prepare the EBS 12.2 adoption

Similar Questions

• Time Machine - there was an error preparing the Time Machine backup drive (could not mount the drive)

  I have a new HD but cannot set up encryption with system preferences. After ten minutes, I get the following error message:

  "There was an error preparing the Time Machine backup disk (disc name) - could not mount drive"

  Apparently, I need to set up the HD in this way:

  • If you are using an external drive connected to your Mac, use disk utility to make sure that your backup disk is formatted in HFS + extended (journaled) and is the partition type GUID Partition Table (GPT)

  It is not an option for the HFS + and so I used; OS x EXTENDED (journaled). GUID is ok.

  Can someone let me know what I need to do.

  Thank you

  Formatting: GUID Partition Table, OS X Extended (journaled).    (it is HFS +)

  For TimeMachine at best to a partition only.

  Do it again if necessary, then disconnect, reconnect, Start Time Machine preferences and "select disk".

• Install Windows 8 on external drive Thunderbolt - Windows could not prepare the computer to begin the next phase of installation

  Hi all

  I'm at my wit's end trying to install windows 8. Let me start at the beginning: I used to have windows running on my Mac Pro ssd internal 8.1, installed via bootcamp. It worked well for a while, and then refused to start, gives me a blue screen KERNEL_SECURITY_CHECK_FAILURE. Despite some advice from lonely T, I was unable to fix and ended up wiping the partition and relocation, again via bootcamp. Yet once again, it worked for a few months, then the same problem. I made this one last time, and it only lasted 2 days... So I gave bootcamp.

  I think that the hybrid MBR partition scheme that implements bootcamp is the culprit, but I don't really have evidence to substantiate this claim. In any case, I tried to install windows in EFI mode. (If I understand correctly, the hybrid MBR is set up to allow windows to install in legacy BIOS mode, but that windows 8 may now install efi, which supports my Mac Pro mode.) My Mac is the new Mac Pro (end of 2013, trash in shape), and I can say short UEFI 2.0 (I have the latest efi update from apple installed).

  The method I'm trying:

  1. create a new partition in HFS + on my external drive using disk utility. The drive has now it's efi partition and partition empty 750Go I want to install windows a 1.25 TB storage partition that I use with my mac. It has a GPT. I formatted HFS + and no FAT, because I think that disk utility creates the same hybrid-MBR as training camp every time a FAT partition is created.

  2. use gdisk to confirm that the disc does not have a hybrid-MBR. (sudo/dev/disk1 gdisk watch MBR: protection)

  3 restart my mac and hold the possibility to put in place to bring up the boot efi menu.

  4. Select the EFI_Boot DVD icon (that's the windows 8 install dvd that I have in my superdrive USB drive)

  5. go in the menus of the disk selection screen installation and delete the partition in HFS +, I created to install windows on (the format option is not available)

  6. now select "Unallocated space" on the good drive and click Next.

  The problem:

  Partitioning seems to go ok (there is no feedback on this basis, but it proceeds to the next screen, and all new partitions expected are there if I check diskutil list later). He said it is "copy of windows files", but then stops with the error "Windows has no prepare the computer to start the next phase of the installation." To install Windows, restart the installation. "If I restart, I can start the same process all over again and get the same result.

  The Question:

  How I get this error and get windows install?

  Extra pieces:

  • The first time it happened I assumed it was the new sip / thing "without roots" in El Capitan, causing problems, then I disabled, but I still get the same error.
  • After reviewing the diskutil list output after one of installs it without success, I found that a labeled EFI partition has been created after my storage partition (the original efi partition was still there in the upper part of the disc).
  • I have windows 8.1 installed now bootcamp on my internal ssd. It was planned to use it and winToUSB to put windows on my crush, but I found that it only works with usb2. I do not have installed could cause problems with the installation on another disk.
  • Before say you I can't run windows on an external, yes you can, and many people have. I read windows sees thunderbolt internal disks.
  • I read a few other posts on this and other sites on this problem, but could not find a pertitnant solution to my situation. I found one that suggested to remove the efi on my disk partition, but that seemed like a bad idea, so I didn't try.
  • I write this at 1 in the morning after a day spent in front of the computer trying to get this working, so please excuse typos typing or other. I am pleased to provide you with any pertinant information helping you will help me.
  • Thank you!

  The other thing I tried also almost succeeded:

  Although I prefer to get the method above works, because it seems the most promising, is something else, I've tried that I thought worth mentioning. If you offer advice pertaining to this method rather than the above, I would appreciate it if you could explicitly declare that at the top of your answer. Thank you.
  

  I tried to install windows on the physical disk using vmware and virtual box. The instrutctions I followed for this can be found here: http://www.andrewsavory.com/blog/2011/2156 (the only thing different, it's because it's on an external drive, I created the Fat 32 partition manually using disk utility). The first time (using vmware) installation seems to go off without a hitch, but I couldn't get my computer to see the windows partition as bootable with the boot efi menu hold-option regular refined or with system preferences-> startup disk. I think that I was using always inadvertently a hybrid-MBR at this stage. I tried to repeat this new beginning with the first two steps above to avoid the hybrid-MBR. But now when I try to create the virtual machine based on the gross vmdk, it starts to copy the files then says not sufficient permissions and fails. I don't know if it's a permission with the disk or the hard problem. I tried chmod 777 and chown $USER of the vmdk disk (/ dev/disk1s3) does not.

  Wow, that was a long post...

  1. when a second drive is detected by the Windows Setup program, he wants to create his own brand of EFI (104 MB) and not to mess with the Mac EFI (200 MB). You can force it to use the EFI to the Mac using Diskpart commands.

  2 instead of HFS/FAT32, create a piece of 750 GB free space and it should only get a new MSR/MSD, without the part of EFI.

  3. on your VM method, the link you have is quite old. You have a MP 2013, with references to the 2010 Mac alumni and is a bit too archaic to be useful. http://forums.macrumors.com/threads/install-a-Windows-7-partition-on-Mac-OSX-Wit hout-optical-car-or - usb.1836959 / #post... seems to work for many and can be useful for a test. It also uses Winclone.

  4. you can also try http://bleeptobleep.blogspot.com/2013/02/mac-install-windows-7-or-8-on-external. html .

• HP ENVY TS m6 Sleekbook: HP ENVY TS m6 Sleekbook will prepare the auto repair when booting with Seagate Backup Plus 2 to

  I had problems for some time with my HP ENVY when you restart.   I have a backup Seagate more Desktop 2 TB connected via a USB hub.    When it is connected and restarting the computer, it goes to the screen to "prepare the AutoFix.   So I have to unplug and restart and that's fine.     I don't know why it continues to be.   I checked my BIOS and it should boot from the hard drive first.     Any ideas?

  @mikejenkins1,

  Hello and thanks for the display on the HP support forums.  Using a USB hub, you get a signal from one of the disks is trying to make a repair due to a possible disconnection during a writing session.  You will need to do is a test on the external drives to see if one of them has problems.  Try to make a direct connect with each drive connected by tonight and see if they are the problem on their own.

  If one of them is causing the problem, try and use the test drive of windows.  Here is a link to help you with that.

  Check a drive for errors

  Please let me know how things are going.

  Thanks again for posting and have a great day.

• Laptop stuck on the screen to "prepare the AutoFix.

  My laptop HP a few months came pre-installed with windows 8. When I tried to start it this morning it came with the screen to "Prepare the automatic repair" and is pasted on it. It is not off or change to a different screen as "scan your computer. I'm sure that it does not start in safe mode by pressing f8 or shift + f8, Ive tried several times. I don't know what to do because it's just stuck on the same screen "prepare auto repair.

  This is not a good thing. The long test. Post the results here.

  The result of the test is indicative of a hard disk failure requiring the replacement of the hard disk.

  Contact HP for a replacement under warranty hard drive. You will need the failure status code providing for the drive test hard when you contact HP.

  It's time to find your set of recovery disks. You will need to install the operating system and the software that came with your laptop.

  Best regards
  ERICO

• WS 2012 and NAS backup failed to prepare the backup image

  Hello

  I'm trying to back up some of my data to Windows server 2012. I am using LG - 250GL Buffalo NAS.

  I use the scheduled backup option, but it is unable to prepare the backup image, error code is "0x807800C5", event id 517."

  However, if I rename my folder name, and then it creates the folder and with successful backup my data, only problem is that it is said version is not compatible. Once again, if I change the name of the folder, it's OK, but I can't do that everyday manually, everything save automatically at certain time.

  I tried to find a solution, but nothing works.

  Maybe my NAS is a bit too old and is not compatible with the version of 2012.

  What are my options? Should I buy new SIN or is it fixable somehow?

  This issue is beyond the scope of this site (for consumers) and to be sure, you get the best (and fastest) reply, we have to ask either on Technet (for IT Pro) or MSDN (for developers)
  *

  http://social.technet.Microsoft.com/forums/en-us/home s/fr-U.S./Accueil
  http://social.msdn.Microsoft.com/Forum
  
  
  If you give us a link to the new thread we can point to some resources it

• My HP Photosmart Premium is saying "preparing the printer can not be interrupted. Please wait... "What is happening?

  My HP Photosmart Premium is saying "preparing the printer can not be interrupted.  Please wait... "What is happening?

  http://h30434.www3.HP.com/T5/scanning-faxing-and-copying/HP-Photosmart-premium-error-message/TD-p/1470957

  HP support

  Edit:

  I know that maybe it's a little late to come and see this post was several months ago, but I had the same problem.

  I ended up turning off the machine and opening printer and check the ink cartridges (I had seen just to find the part number for a new cartridge).  I found that the blue cover which snaps into place on the ink cartridges was broken not closed completely.  This has caused the printer constantly tries to go into maintenance mode, but it could never align cartridges.  She also told me that there is a paper jam, even when there is no paper in the machine.  I even let the maintenance run all night without success.

  Once the cartridges have been broken in place and the blue cover has been fully guaranteed, the printer worked.

  above compositions of this thread:

  http://h30434.www3.HP.com/T5/eprint-print-apps-mobile/HP-OfficeJet-Pro-8500A-plus-printer-is-stuck-in-maintenance-mode/TD-p/1207907

• 'Prepare the empty disc' when I insert a CD or DVD

  When I insert any type of disc in my CD/DVD drive, he invites me to "prepare the empty drive. I can't find a solution that actually works. Help!

  Diane

  Hi Diane,

  1 have had any changes made to your computer before this problem?

  2. did you recently install a service pack in Vista computer or update the drivers?

  3. you try to burn a CD/DVD?

  Perform the following methods and check if it helps.

  Method 1:

  Please run the difficulty of following article and check if that helps.

  Your CD or DVD drive cannot read or write media

  http://support.Microsoft.com/mats/cd_dvd_drive_problems/en-us

  Method 2:

  You can read the following article to see what might cause this problem.

  When you insert a CD or a DVD, Windows Vista may not recognize the disc

  http://support.Microsoft.com/kb/939052/en-us

  If you had recently upgraded the computer to the Vista operating system or install the Service Packs, then try the steps as described in the following article.

  The CD drive or the DVD drive does not work as expected on a computer that you upgraded to Windows Vista

  http://support.Microsoft.com/kb/929461/en-us

  Important: This section, method, or task contains steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click on the number below to view the article in the Microsoft Knowledge Base:

  How to back up and restore the registry in Windows

  http://support.Microsoft.com/kb/322756/  

  Hope this information is useful.

• Windows didn't prepare the computer to start the next phase of installation

  Hey I get the error "windows has no prepare the computer to start the next phase of installation" during the installation of vista and Windows 7, I use xp professional I would like to mention that a few days ago, I company vista works well, so I thought I should update to the win 7 but since that day I have my receive this error message and also I could not install vista  , the specifications of the system are: optima PC with motherboard 2.8 GHz intel and intel 865GLC inside the processor 2.8 GHz, 1 GB ram, 160 GB HDD
  PLEASE please help me I lost so much time, but all in vain :(: @.
  I also tried msconfig utility chkdsk, but she shows that its fine and also unplugged all other additional devices in the connection only the mouse and keybard but no American (e):
  PLEASE SOMEONE HELP ME

  Hello

  These are forums for vista for home pc users

  you use enterprise

  Try the vista it pro forums

  http://social.technet.Microsoft.com/forums/en-us/category/windowsvistaitpro/

• prepare the config for the model/tool switches

  Guys,

  I'm trying to find out if there is a tool to prepare config Cisco routers/switches. I'm looking to prepare the basic config with some VLANS, static IP, etc. of the AAA. Should I use GNS3 as Simulator to simulate a router and configure it to serve as a model or if there is another free light weight tool where I can test config for typo errors or something.

  Thanks in advance!

  If you have existing switches just the running-config and get some simple editor like Notepad and change the IP addresses and other things

  Add No. SHUTDOWN on the interfaces, because by default they are not upward, and when you do a show running-config it does not appear as no. SHUTDOWN.

• Cannot install Windows 7 "Windows didn't prepare the computer to start the next phase of the installation." to install Windows, restart the application.

  Original title: Installation of Windows 7.

  I tried to install Windows 7 (clean install from XP and reveived the following message is displayed:)

  Windows didn't prepare the computer to start the next phase of the installation.  to install Windows, restart the application.

  I restarted my PC, anti anti-virus disabled (as advised) and still get the error message.

  According to the Upgrade Advisor Windows 7 my PC is compatible.

  Any ideas?

  If you have compatible hardware and your computer still stops responding, disable any unnecessary material. Remove (USB) universal serial bus devices. Remove or disable network cards, sound cards and cards of the series; and then restart the installation.

  Boot from the Windows 7 DVD
  Click Install now
  Accept the license agreement
  When the option is displayed to select a type of installation, click (Custom advanced)

  Select the disk partition where you want to install Windows 7 click Next.

  You will receive the following warning:

  The partition you have selected may contain files from a previous Installation of Windows. If so, these files and folders will be moved to a folder named Windows.old. You will be able to access the information in Windows.old, but you will be able to use your previous version of Windows.

  (At all costs, do NOT click on anything in Format, deletion or Partition name.) So even do a custom installation, your personal files are still kept. Click OK

  The installation program will now begin installation. During installation, your computer will be restarted several times.

  Once the installation is complete, you can complete the Out of Box experience as the choice of your laptop, create a username, password, your time zone. You can then proceed to download the latest updates for Windows and reinstall your applications and drivers.

  You can then retrieve your personal files from the Windows.old folder and reinstall all of your applications and drivers.

  http://notebooks.com/2010/11/09/how-to-recover-documents-music-and-email-after-upgrading-with-the-Windows-old-folder/

• I get an error message when the computer starts, "failed to prepare the critical file! Engine out of Chameleon.

  I have a laptop Asus N53Jq, 16 GB, 224 GB ssd, I get an error message when the computer starts, "failed to prepare the critical file! Engine out of Chameleon"when I click the computer works fine, but it seems that she was taking more resources without doing me anything. Do know how to solve this problem.

  Original title: Chameleon engine

  I uninstalled ASUS Splendid Video Enhancement Technology to my computer and it solved the problem!

• Download "Windows didn't prepare the computer to start the next phase of the installation during installation of Windows7.

  When installing windows7 in the second phase, it gives error such as ' Windows has not to prepare the computer to start in the next phase of installation.to install Windows, restart the installation. " It comes at the end of 50% of the extraction of windows.

  How you attempt installation?

  You are upgrading from a previous version of Windows?

  Are there devices non-essential attached to the system as a external hard drive or USB key?

  If so, try to disconnect them, they might interfere with installation.

  Could you give your full system specs?

  If you have compatible hardware and your computer still stops responding, disable any unnecessary material. Remove (USB) universal serial bus devices. Remove or disable network cards, sound cards and cards of the series; and then restart the installation.

  1 disable any security software before attempting to upgrade

  2. make sure that your computer is updated (devices and applications)

  3. disconnect all external devices before installing.

  4. check your hard disk for errors:

  Click Start

  Type: CMD, according to the results, right-click CMD

  Click on "Run as Administrator"

  At the command prompt, type: chkdsk /f /r

  When you restart your system, your computer will be scanned for errors and will try to correct them.

  1. click on start, type msconfig in the search box and press ENTER.

  User account control permission

  If you are prompted for an administrator password or a confirmation, type the password, or click on continue.

  2. in the general tab, click Selective startup.

  3. under Selective startup, clear the check box load startup items.

  4. click on the Services tab, select the hide all Microsoft Services check box, and then click Disable all.

  5. click on OK.

  6. When you are prompted, click on restart.

  7. after the computer starts, check if the problem is resolved.

  Also run the Windows 7 Upgrade Advisor:

  http://www.Microsoft.com/Windows/Windows-7/Upgrade-Advisor.aspx

• Convert the EBS for one example at RAC

  Hi all

  EBS R12.2.4

  11 GR 2

  OL 6.5

  I want to convert our EBS instance to RAC.

  Can you share me documentation on how to convert a single instance of the EBS R12.2.4 CARS?

  I need to convert both the apps and the level of db? or the level of db only?

  Kind regards

  JC

  Hi Vishnu,

  I ran the 2nd step: but received the error

  rman target $ /.

  Recovery Manager: release 11.2.0.3.0 - Production on Tue Feb 23 11:42:11 2016

  Copyright (c) 1982, 2011, Oracle and/or its affiliates.  All rights reserved.

  RMAN-00571: ===========================================================

  RMAN-00569: = ERROR MESSAGE STACK FOLLOWS =.

  RMAN-00571: ===========================================================

  RMAN-00554: initialization of the package manager internal collection failed

  RMAN-04005: target database error:

  ORA-21561: OID generation failed

  Kind regards

• Reconciliation of the EBS target does not work for the payments.

  Hi all

  I use OIM 11 g 2 and Oracle EBS user Managment 9.1.0.7.0 connector.
  I want to link the user's responsibilities in EBS your child to IOM. I tried to use the Scheduler ""eBusiness UM target user reconciliation resource ' but the execution of this work is just creating the EBS account for the user at the IOM. " I can see the user's responsibilities in the details information of the EBS account, which was created by the work of reconciliation of target, but I don't see them as the user rights

  How can I achieve this?

  Any help is appreciated.

  Thank you and best regards,

  Thank you for your help. I solved this problem with the use of assignments of rights enforcement after the work MU target resource user reconciliation eBusiness