Pro-grammatically discover remote devices (cRIO or sbRIO) within the Local network
Hi I'm developing an application where I need to configure my cRIOs. So first of all, I need to find out all the RIO within the network and configure one by one by selecting their IP address in the list.
What someone has to know everything how to discover. I think there must be a solution that MAX discover any type of remote devices.
Help, please.
You specify the version of LabVIEW you use. In LabVIEW 2009, you can use the RT to target information VI for a list of all targets of RT on your local subnet.
Tags: NI Hardware
Similar Questions
-
* Original title: this page cannot be display the remote or unit does not accept the connection. (! found)
My internet connection works very well, I'm trying to access a page of my gate of the school we use to complete missions. I can access my web page of schools, I can access my e-mail from the school, but I can't get the e-portfolio page. It says cannot display this page - the remote device and does not accept the connection - (! found). He said to ensure that the TSL and SSL in the advanced internet options security part turned on who they are, my better protected as well the mode. I've never had a problem accessing this page before. It is only this page! Help!
Hello Teresa,.
The probable cause of this problem could be due to wrong settings for internet explore.
Please see the link below, Windows 8, follow the steps to check the Proxy and DNS settings
http://support.Microsoft.com/kb/956196/en-usWarning: Reset the Internet Explorer settings can reset security settings or privacy settings that you have added to the list of Trusted Sites. Reset the Internet Explorer settings can also reset parental control settings. We recommend that you note these sites before you use the reset Internet Explorer settings.
Hope this helps, please answer with the results for assistance.
-
Re: Satellite Pro A40 - connection to the local network
Hello
My names Andy and not bieng a total beginner computer, I tried to install all the drivers for my laptop model a SPA40 old fathers PSA45E-001VM-EN. (European model I think) everything looks ok, except that I can't get the ETHERNET driver.
When I go into the Device Manager there is NO controller network displayed in the list and there is a yellow exclamation mark against two controllers ethernet ib the OTHER DEVICES tab looking here, I downloaded the atheros wlan xp file - 7704062.zip, broadcom wlan xp - installed 5604835.ziplan20070912134727.zip and nothing changes, we used to be able to go on the net and with the wifi card in the pci slot wireless go so I know its capable I think it's just the order of drivers and the drivers themselves,
Then someone can point me in the right direction before as I have send myself crazy with this...
You can
regards and thanks in advance
Andy
Hey,.
The drivers that you downloaded are WLAN Card and has nothing to do with the connection to the local network (Ethernet) normal
I think you should check the Web from Toshiba site to download the latest LAN driver. You can find the drivers for Satellite Pro A40 in * archives *.
ttp://EU.computers.Toshiba-Europe.com/innovation/download_drivers_bios.jsp h -
Client remote access VPN gets connected without access to the local network
: Saved
:
ASA 1.0000 Version 2
!
hostname COL-ASA-01
domain dr.test.net
turn on i/RAo1iZPOnp/BK7 encrypted password
i/RAo1iZPOnp/BK7 encrypted passwd
names of
!
interface GigabitEthernet0/0
nameif outside
security-level 0
IP 172.32.0.11 255.255.255.0
!
interface GigabitEthernet0/1
nameif inside
security-level 100
IP 192.9.200.126 255.255.255.0
!
interface GigabitEthernet0/2
Shutdown
No nameif
no level of security
no ip address
!
interface GigabitEthernet0/3
Shutdown
No nameif
no level of security
no ip address
!
interface GigabitEthernet0/4
Shutdown
No nameif
no level of security
no ip address
!
interface GigabitEthernet0/5
nameif failover
security-level 0
192.168.168.1 IP address 255.255.255.0 watch 192.168.168.2
!
interface Management0/0
nameif management
security-level 0
192.168.2.11 IP address 255.255.255.0
!
passive FTP mode
DNS server-group DefaultDNS
domain dr.test.net
network of the RAVPN object
192.168.0.0 subnet 255.255.255.0
network of the NETWORK_OBJ_192.168.200.0_24 object
192.168.200.0 subnet 255.255.255.0
network of the NETWORK_OBJ_192.9.200.0_24 object
192.9.200.0 subnet 255.255.255.0
the inside_network object-group network
object-network 192.9.200.0 255.255.255.0
external network object-group
host of the object-Network 172.32.0.25
Standard access list RAVPN_splitTunnelAcl allow 192.9.200.0 255.255.255.0
access-list extended test123 permit ip host 192.168.200.1 192.9.200.190
access-list extended test123 permit ip host 192.9.200.190 192.168.200.1
access-list extended test123 allowed ip object NETWORK_OBJ_192.168.200.0_24 192.9.200.0 255.255.255.0
192.9.200.0 IP Access-list extended test123 255.255.255.0 allow object NETWORK_OBJ_192.9.200.0_24
pager lines 24
management of MTU 1500
Outside 1500 MTU
Within 1500 MTU
failover of MTU 1500
local pool RAVPN 192.168.200.1 - 192.168.200.254 255.255.255.0 IP mask
no failover
ICMP unreachable rate-limit 1 burst-size 1
ASDM image disk0: / asdm - 66114.bin
don't allow no asdm history
ARP timeout 14400
NAT (inside, outside) source Dynamics one interface
NAT (it is, inside) static static source NETWORK_OBJ_192.9.200.0_24 destination NETWORK_OBJ_192.168.200.0_24 NETWORK_OBJ_192.168.200.0_24 NETWORK_OBJ_192.9.200.0_24
Route outside 0.0.0.0 0.0.0.0 172.32.0.2 1
Timeout xlate 03:00
Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
Floating conn timeout 0:00:00
dynamic-access-policy-registration DfltAccessPolicy
identity of the user by default-domain LOCAL
the ssh LOCAL console AAA authentication
Enable http server
http 0.0.0.0 0.0.0.0 outdoors
http 0.0.0.0 0.0.0.0 inside
No snmp server location
No snmp Server contact
Server enable SNMP traps snmp authentication linkup, linkdown warmstart of cold start
Crypto ipsec transform-set ikev1 ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-DES-SHA esp - esp-sha-hmac
Crypto ipsec transform-set ikev1 SHA-ESP-3DES esp-3des esp-sha-hmac
Crypto ipsec transform-set ikev1 esp ESP-DES-MD5-esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-3DES-MD5-esp-3des esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
Crypto ipsec transform-set ikev1 ESP-AES-128-SHA aes - esp esp-sha-hmac
Crypto ipsec transform-set ikev1 ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
Crypto ipsec transform-set ikev1 ESP-AES-128-MD5-esp - aes esp-md5-hmac
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 pfs Group1 set
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 define ikev1 transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5
outside_map card crypto 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP
outside_map interface card crypto outside
Crypto ca trustpoint ASDM_TrustPoint0
Terminal registration
name of the object CN = KWI-COL-ASA - 01.dr.test .net, C = US, O = KWI
Configure CRL
Crypto ikev1 allow outside
IKEv1 crypto policy 10
authentication crack
aes-256 encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 20
authentication rsa - sig
aes-256 encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 30
preshared authentication
aes-256 encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 40
authentication crack
aes-192 encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 50
authentication rsa - sig
aes-192 encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 60
preshared authentication
aes-192 encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 70
authentication crack
aes encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 80
authentication rsa - sig
aes encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 90
preshared authentication
aes encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 100
authentication crack
3des encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 110
authentication rsa - sig
3des encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 120
preshared authentication
3des encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 130
authentication crack
the Encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 140
authentication rsa - sig
the Encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 150
preshared authentication
the Encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 65535
preshared authentication
3des encryption
sha hash
Group 2
life 86400
Telnet 192.9.200.0 255.255.255.0 inside
Telnet timeout 30
SSH 0.0.0.0 0.0.0.0 management
SSH 0.0.0.0 0.0.0.0 outdoors
SSH 66.35.45.128 255.255.255.192 outside
SSH 0.0.0.0 0.0.0.0 inside
SSH timeout 30
SSH version 2
Console timeout 0
a basic threat threat detection
Statistics-list of access threat detection
no statistical threat detection tcp-interception
WebVPN
allow outside
AnyConnect image disk0:/anyconnect-win-2.5.2014-k9.pkg 1
AnyConnect enable
tunnel-group-list activate
attributes of Group Policy DfltGrpPolicy
internal RAVPN group policy
RAVPN group policy attributes
value of server WINS 192.9.200.164
value of 66.35.46.84 DNS server 66.35.47.12
VPN-filter value test123
Ikev1 VPN-tunnel-Protocol
Split-tunnel-policy tunnelspecified
Split-tunnel-network-list value test123
Dr.kligerweiss.NET value by default-field
username test encrypted password xxxxxxx
username admin password encrypted aaaaaaaaaaaa privilege 15
vpntest Delahaye of encrypted password username
type tunnel-group RAVPN remote access
attributes global-tunnel-group RAVPN
address RAVPN pool
Group Policy - by default-RAVPN
IPSec-attributes tunnel-group RAVPN
IKEv1 pre-shared-key *.
!
class-map inspection_default
match default-inspection-traffic
!
!
type of policy-card inspect dns preset_dns_map
parameters
maximum message length automatic of customer
message-length maximum 512
Policy-map global_policy
class inspection_default
inspect the preset_dns_map dns
inspect the ftp
inspect h323 h225
inspect the h323 ras
Review the ip options
inspect the netbios
inspect the rsh
inspect the rtsp
inspect the skinny
inspect esmtp
inspect sqlnet
inspect sunrpc
inspect the tftp
inspect the sip
inspect xdmcp
!
global service-policy global_policy
context of prompt hostname
no remote anonymous reporting call
call-home
Profile of CiscoTAC-1
no active account
http https://tools.cisco.com/its/service/oddce/services/DDCEService destination address
email address of destination [email protected] / * /
destination-mode http transport
Subscribe to alert-group diagnosis
Subscribe to alert-group environment
Subscribe to alert-group monthly periodic inventory 2
Subscribe to alert-group configuration periodic monthly 2
daily periodic subscribe to alert-group telemetry
aes encryption password
Cryptochecksum:b001e526a239af2c73fa56f3ca7667ea
: end
COL-ASA-01 #.
Here is a shot made inside interface which can help as well, I've tried pointing the front door inside the interface on the target device, but I think it was a switch without ip route available on this subject I think which is always send package back to Cisco within the interface
Test of Cape COLLAR-ASA-01 # sho | in 192.168.200
25: 23:45:55.570618 192.168.200.1 > 192.9.200.190: icmp: echo request
29: 23:45:56.582794 192.168.200.1.137 > 192.9.200.164.137: udp 68
38: 23:45:58.081050 192.168.200.1.137 > 192.9.200.164.137: udp 68
56: 23:45:59.583176 192.168.200.1.137 > 192.9.200.164.137: udp 68
69: 23:46:00.573517 192.168.200.1 > 192.9.200.190: icmp: echo request
98: 23:46:05.578110 192.168.200.1 > 192.9.200.190: icmp: echo request
99: 23:46:05.590057 192.168.200.1.137 > 192.9.200.164.137: udp 68
108: 23:46:07.092310 192.168.200.1.137 > 192.9.200.164.137: udp 68
115: 23:46:08.592468 192.168.200.1.137 > 192.9.200.164.137: udp 68
116: 23:46:10.580795 192.168.200.1 > 192.9.200.190: icmp: echo request
COL-ASA-01 #.
Any help or pointers greatly appreciated, I have do this config after a long interval on Cisco of the last time I was working it was all PIX so just need to expert eyes to let me know if I'm missing something.
And yes I don't have a domestic network host to test against, all I have is a switch that cannot route and bridge default ip helps too...
Hello
The first thing you should do to avoid problems is to change the pool VPN to something else than the current LAN they are not really directly connected in the same network segment.
You can try the following changes
attributes global-tunnel-group RAVPN
No address RAVPN pool
no mask RAVPN 192.168.200.1 - 192.168.200.254 255.255.255.0 ip local pool
local pool RAVPN 192.168.201.1 - 192.168.201.254 255.255.255.0 IP mask
attributes global-tunnel-group RAVPN
address RAVPN pool
no nat (it is, inside) static source NETWORK_OBJ_192.168.200.0_24 NETWORK_OBJ_192.168.200.0_24 static destination NETWORK_OBJ_192.9.200.0_24 NETWORK_OBJ_192.9.200.0_24
In the above you first delete the VPN "tunnel-group" Pool and then delete and re-create the VPN pool with another network and then insert the same "tunnel-group". NEX will remove the current configuration of the NAT.
the object of the LAN network
192.168.200.0 subnet 255.255.255.0
network of the VPN-POOL object
192.168.201.0 subnet 255.255.255.0
NAT (inside, outside) 1 static source LAN LAN to static destination VPN-VPN-POOL
NAT configurations above adds the correct NAT0 configuration for the VPN Pool has changed. It also inserts the NAT rule to the Summit before the dynamic PAT rule you currently have. He is also one of the problems with the configurations that it replaces your current NAT configurations.
You have your dynamic PAT rule at the top of your NAT rules currently that is not a good idea. If you want to change to something else will not replace other NAT configurations in the future, you can make the following change.
No source (indoor, outdoor) nat Dynamics one interface
NAT source auto after (indoor, outdoor) dynamic one interface
NOTICE! PAT dynamic configuration change above temporarily interrupt all connections for users on the local network as you reconfigure the dynamic State PAT. So if you make this change, make sure you that its ok to still cause little reduced in the current internal users connections
Hope this helps
Let me know if it works for you
-Jouni
-
HP OfficeJet Pro 8600, connected to the local network but cannot print printer on the same local network.
Work tried fixing it but all attempts fail.
Firewall disabled.
Printer recognizes the router's LAN.
Was also pointed out that the port does not communicate, can not remove it; Cannot add another...
Printer does not print.
How can I fix?
Hi @AnnisMonadjem,
Welcome to the Forums of HP Support!
I understand that you are unable to print to your printer HP Officejet Pro 8600. I'd be happy to help you and don't forget to come back to this thread and check "Accept as Solution", if I have successfully helped solve you the problem. If you want to say 'Thank you' to my effort to help, click on the "thumbs up" to give me a Kudos.
When you say 'LAN', are you referring to the network or you try to share the printer on the network?
How is the printer connected? (Ethernet/WiFi)
If you have noticed that the port is causing problems, please download and run the print and Scan doctor, it will be probably diagnose and fix the problem you are experiencing.
What were the results when you ran the Print and Scan Doctor? (she print or scan, error messages)
HP has several Officejet Pro 8600 series.
What is the name and the product number of your printer? How can I find my model number or product number?
- Update the firmware of the printer.
- Don't hide the SSID (network name).
- What type of encryption are you helping? HP recommends WPA and WPA2.
- You have a double router broadband? Make sure that the two groups were not the same network name.
If the problem persists, you may encounter an IP address conflict. It's a good idea to assign the printer a static IP address outside your DHCP range. For example, some routers default DHCP is located between 192.168.0.100 to 192.168.0.200. So, I would use 192.168.0.232.
To assign the static IP address, use the following steps as a guide.
- Print a Page of Network Configuration menu of the printer front panel. Note the IP printer. IPV4 address
- Type the IP address in the browser to bring up the SAP.
- Choose the network tab, then wireless on the left side, and then select the IPv4 tab.
- Select Manual IP.
- Enter your IP address manual (192.168.0.232)
- Enter 255.255.255.0 for the subnet mask, except if it is different.
- Enter the IP address of your router that sits on the Network Configuration Page) for the default gateway.
- Please, click on manual DNS server. For the preferred DNS Server Manual please enter 8.8.8.8 and the Alternate DNS Server Manual, please enter 8.8.4.4.
- Click on apply.
- Restart the router, the printer and the computer.
- Test printing and scanning.
If the problem persists, download and run this patch rollup: resolving printing issues in Windows 7 and Windows Server 2008 R2
- Try printing and scanning.
In addition, if you are still having problems try the steps in this guide, HP printers - "offline" Status Message printer (Windows 7).
Continue on, if the problem persists.
Important! Delete the temporary files and folders by using the disk cleanup utility
- Open the disk cleanup utility:
-
ASA5505 can transfer clients to remote VPN access to the local network
I have currently ASA 5505 and 2911-router and I am trying to configure the VPN topology.
Can ASA5505 you transmit to remote VPN access clients LAN operated by another router?
These two cases are possible? :
(1) ASA 5505 and 2911-router are separate WAN interfaces, each connected directly to the ISP. But so can I connect an other interfaces LAN of ASA 5505 in a switch managed by 2911 router customers to distance-SSL-VPN to inject into the local network managed by the router?
(2) ASA 5505 is behind router-2911. May 2911 router address public ip or public ip address VPN-access attempts have directly be sent to ASA 5505 when there is only a single public ip address address available?
Long put short, ASA 5505 can inject its clients to remote-access-VPN as one of the hosts on the local network managed by 2911-router?
Thank you.I could help you more if you can explain the purpose of this configuration and connectivity between the router and ASA.
You can activate the reverse route on the dynamic plane on the SAA. The ASA will install a static route to the customer on the routing table. You can use a routing protocol to redistribute static routes to your switch on the side of LAN of the SAA.
-
remote VPN and vpn site to site vpn remote users unable to access the local network
As per below config remote vpn and vpn site to site vpn remote users unable to access the local network please suggest me a required config
The local 192.168.215.4 not able ping server IP this server connectivity remote vpn works fine but not able to ping to the local network vpn users.
ASA Version 8.2 (2)
!
host name
domain kunchevrolet
activate r8xwsBuKsSP7kABz encrypted password
r8xwsBuKsSP7kABz encrypted passwd
names of
!
interface Ethernet0/0
nameif outside
security-level 0
PPPoE client vpdn group dataone
IP address pppoe
!
interface Ethernet0/1
nameif inside
security-level 50
IP 192.168.215.2 255.255.255.0
!
interface Ethernet0/2
nameif Internet
security-level 0
IP address dhcp setroute
!
interface Ethernet0/3
Shutdown
No nameif
no level of security
no ip address
!
interface Management0/0
Shutdown
No nameif
no level of security
no ip address
management only
!
passive FTP mode
clock timezone IST 5 30
DNS server-group DefaultDNS
domain kunchevrolet
permit same-security-traffic intra-interface
object-group network GM-DC-VPN-Gateway
object-group, net-LAN
access extensive list ip 192.168.215.0 sptnl allow 255.255.255.0 192.168.2.0 255.255.255.0
192.168.215.0 IP Access-list extended sheep 255.255.255.0 allow 192.168.2.0 255.255.255.0
tunnel of splitting allowed access list standard 192.168.215.0 255.255.255.0
pager lines 24
Enable logging
asdm of logging of information
Outside 1500 MTU
Within 1500 MTU
MTU 1500 Internet
IP local pool VPN_Users 192.168.2.1 - 192.168.2.250 mask 255.255.255.0
ICMP unreachable rate-limit 1 burst-size 1
enable ASDM history
ARP timeout 14400
NAT-control
Global 1 interface (outside)
NAT (inside) 1 0.0.0.0 0.0.0.0
Route outside 0.0.0.0 0.0.0.0 59.90.214.1 1
Timeout xlate 03:00
Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
dynamic-access-policy-registration DfltAccessPolicy
the ssh LOCAL console AAA authentication
AAA authentication LOCAL telnet console
AAA authentication http LOCAL console
AAA authentication enable LOCAL console
LOCAL AAA authentication serial console
Enable http server
x.x.x.x 255.255.255.252 out http
http 192.168.215.0 255.255.255.252 inside
http 192.168.215.0 255.255.255.0 inside
No snmp server location
No snmp Server contact
Server enable SNMP traps snmp authentication linkup, linkdown cold start
Crypto ipsec transform-set esp-3des esp-sha-hmac RIGHT
life crypto ipsec security association seconds 28800
Crypto ipsec kilobytes of life - safety 4608000 association
Crypto-map dynamic dynmap 65500 transform-set RIGHT
card crypto 10 VPN ipsec-isakmp dynamic dynmap
card crypto VPN outside interface
card crypto 10 ASA-01 set peer 221.135.138.130
card crypto 10 ASA - 01 the transform-set RIGHT value
crypto ISAKMP allow outside
crypto ISAKMP policy 10
preshared authentication
3des encryption
sha hash
Group 2
life 86400
crypto ISAKMP policy 65535
preshared authentication
the Encryption
sha hash
Group 2
lifetime 28800
Telnet 192.168.215.0 255.255.255.0 inside
Telnet timeout 5
SSH 0.0.0.0 0.0.0.0 outdoors
SSH timeout 5
Console timeout 0
management-access inside
VPDN group dataone request dialout pppoe
VPDN group dataone localname bb4027654187_scdrid
VPDN group dataone ppp authentication chap
VPDN username bb4027654187_scdrid password * local store
interface for identifying DHCP-client Internet customer
dhcpd dns 218.248.255.141 218.248.245.1
!
dhcpd address 192.168.215.11 - 192.168.215.254 inside
dhcpd allow inside
!
a basic threat threat detection
Statistics-list of access threat detection
no statistical threat detection tcp-interception
Des-sha1 encryption SSL
WebVPN
allow outside
tunnel-group-list activate
internal kun group policy
kun group policy attributes
VPN - connections 8
Protocol-tunnel-VPN IPSec
Split-tunnel-policy tunnelspecified
Split-tunnel-network-list value split tunnel
kunchevrolet value by default-field
test P4ttSyrm33SV8TYp encrypted password username
username kunauto password bSHrKTGl8PUbvus / encrypted privilege 15
username kunauto attributes
Strategy Group-VPN-kun
Protocol-tunnel-VPN IPSec
tunnel-group vpngroup type remote access
tunnel-group vpngroup General attributes
address pool VPN_Users
Group Policy - by default-kun
tunnel-group vpngroup webvpn-attributes
the vpngroup group alias activation
vpngroup group tunnel ipsec-attributes
pre-shared key *.
type tunnel-group test remote access
tunnel-group x.x.x.x type ipsec-l2l
tunnel-group ipsec-attributes x.x.x.x
pre-shared key *.
!
class-map inspection_default
match default-inspection-traffic
!
!
type of policy-card inspect dns preset_dns_map
parameters
maximum message length automatic of customer
message-length maximum 512
Policy-map global_policy
class inspection_default
inspect the preset_dns_map dns
inspect the ftp
inspect h323 h225
inspect the h323 ras
Review the ip options
inspect the netbios
inspect the rsh
inspect the rtsp
inspect the skinny
inspect esmtp
inspect sqlnet
inspect sunrpc
inspect the tftp
inspect the sip
inspect xdmcp
inspect the icmp
!
global service-policy global_policy
context of prompt hostname
call-home
Profile of CiscoTAC-1
no active account
http https://tools.cisco.com/its/service/oddce/services/DDCEService destination address
email address of destination [email protected] / * /
destination-mode http transport
Subscribe to alert-group diagnosis
Subscribe to alert-group environment
Subscribe to alert-group monthly periodic inventory
monthly periodicals to subscribe to alert-group configuration
daily periodic subscribe to alert-group telemetry
Cryptochecksum:0d2497e1280e41ab3875e77c6b184cf8
: end
kunauto #.Hello
Looking at the configuration, there is an access list this nat exemption: -.
192.168.215.0 IP Access-list extended sheep 255.255.255.0 allow 192.168.2.0 255.255.255.0
But it is not applied in the States of nat.
Send the following command to the nat exemption to apply: -.
NAT (inside) 0 access-list sheep
Kind regards
Dinesh Moudgil
P.S. Please mark this message as 'Responded' If you find this information useful so that it brings goodness to other users of the community
-
Win 7 pro license on 2 devices if one desktop and the second a mobile?
Hello
I have read, it is possible to install a win 7 pro license on 2 devices if one is a desktop computer and the second mobile (Tablet, netbook or laptop).Is this true?If yes how to do it please?I bought a laptop with win 7 pro on this subject and we must now install it on a new desktop computer that I am editing.THXThis is not true.
No, the key that can be used with 32-bit or 64-bit Windows 7 is exclusively for use with the disc 1. You cannot use install both. 1 license, 1 installation, so choose wisely. If you want to install Windows 7 32 or 64 bit on another partition or another computer, you must purchase an additional license.
http://www.Microsoft.com/Windows/buy/default.aspx
http://Windows.Microsoft.com/en-us/Windows7/get-a-new-Windows-product-key
INSTALLATION AND USE RIGHTS.
a. one copy per computer. You can install one copy of the software on a single computer. This computer is "licensed computer.
b. a computer license. You can use the software on up to two processors of the computer under license at some point. Except as provided in these license terms, you cannot use the software on any other computer.
c. number of users. Except as provided in these license terms, only one user may use the software at a time.
d. other Versions. The software may include several versions, such as 32-bit and 64-bit. You may install and use only one version at a time.
-
Satellite Pro A100 has "limited or no connectivity" & no connection to the local network
Hello!
I + really + hope someone might be able to help with this - been going slowly crazy.
Bought my A100 18 months ago in Australia while I lived there and had no trouble to connect to LANs and others with my wireless. Everything was shipped over to me (here in London) last week and everything seems to have gone pear shaped. The House I live in has Wireless Broadband comes with our Sky Cable subscription, working on (I think - there is no real marking on the device) a router wireless Netgear A/G dual band (108 Mbps 802.11 b/g network). My laptop model is: SatellitePro A100 (part No.: PSAACE-007002EN) and it works on the following network hardware (drivers installed in brackets):
1394 net adapter (5.1.2535.0)
Intel(r) PRO/1000 PL Network Connection (9.2.24.0)
Intel (R) PRO/Wireless 3945ABG Network Connection (10.1.0.13)I used the Sky Broadband installation disc to set up the network, but every time I try to connect it tells me that I have "Limited or no connectivity" and will not let me online. I've been on the phone for Technical Support of sky for hours, trying to get this sort, but when I plug in the Ethernet cable to the laptop it will not even get to communicate directly with the router (i.e. put the IP address of the router in explore and view the settings of the router). My 'Connectivity Doctor' shows there is a problem with my wireless connection (which the network has not assigned a network address of the computer), but no problem with my ethernet connection and yet neither will allow me to get online and every time that I try to repair the wireless connection I get an error message saying that Windows could not renew the IP address.
I have disabled the Bluetooth, reset the router I don't know how many times and made sure that all cards have been activated and crosses without bad red and yellow exclaimation in Device Manager. All network devices seem to be "working properly" (according to the properties of the device).
After days of weeding through the proverbial haystack of resources online while at work, I think that the problem is either something very simple (i.e. a setting random advanced configuration). I read somewhere as you will need to 'install' the router on the system, and that is not "plug and play" as Sky Broadband seems to have deduced by phone... but I would have thought the installation CD has done this, as when I discovered my connections (when the Ethernet cable is plugged in), it recognizes the connection (it won't only ++ anything). If there is no specific process I need to follow in order to properly install the Netgear router (for which I am currently trying to see if there are appropriate drivers, I need to download), I'd appreciate a lot of the age of enlightenment! It could also be a question that I need to reset the network key in the security settings of the router, as there are already three computers in the House connected to the network... but of course I can not do without first sorting on why my laptop can still communicate with the router via the Ethernet connection.
Points to note:
-My laptop runs on Windows XP Professional Version 2002 Service Pack 2
-The disc to install Sky Broadband installed Internet Explorer 7. the last time I was online, I think that I was still using 6.If anyone could be of any use to solve this puzzle, you have earned yourself my eternal gratitude!
-Danielle
Hello
I think that the solution should be simple;
I presume that you TCP/IP settings are false. I mean that the settings should be set to automatically assign the IP address.Please check this box. Simply go to the network connections-> local network connections TCP/IP properties properties
He put everything on automatic
-
Satellite M30-S309: cannot change on the local network adapter device
Hello
My name is Sebastian and I have a Satellite M30-S309 I can't configure IT the Connection WiFi.
The drivers its OK (and reinstall) the LAN, but the WiFi RADIO network ok is OFF, have any opportunity to step ON this Board?I reinstall the KEYBOARD shortcut, but I think that the app or utility for the Fn + F8 key and the LED does not.
Any can help me?
Thanks in advance,S.
You said the LAN is ok, but are you sure that the wireless network adapter has been installed on this laptop. Please check in the area to network adapters Device Manager.
If the wireless network adapter has been installed, you should see the wireless network card in this area. As much as I k now the Wlan switch on the front of the laptop works only if the wireless network adapter has been placed. -
How to prohibit remote access vpn client to use the local DNS server
Hello
I'm on ASA5505 remote access vpn configuration.
Everything works fine so far, except when the client got connected, he always used the local DNS server provided by the ISP. How can I force the customer to use the DNS server configured on ASA?
Thank you.
Kind regards
The command "Activate dns split-tunnel-all" is supported only on SSL VPN and VPN IKEv2. Since you're using IKEv1, this command is not supported.
Here's the order reference:
http://www.Cisco.com/en/us/docs/security/ASA/asa82/command/reference/S8.html#wp1533793
You configure no split tunnel? If you are, then you need to configure "tunnelall" split tunnel policy, and that will force the dns resolution and everything else through the VPN tunnel.
-
Loggin to the administrator of the remote site redirects to localhost on the local server.
This is certainly news to me. I created a Wordpress site locally and then uploaded to the remote server. For some reason when I connect I get redirected to the local host and the version installed locally in XAMPP. I tried to clear the cache in Firefox, but nothing helped. When Apache and MySQL are disabled in the XAMPP Control Panel, he always tries to redirect to the local server and I get the error "problem loading page".
Also, strangely, when I disable XAMPP the CSS for the site on the REMOTE server is not displayed! Any ideas short of clear and start over? I can't even to the admin of the site to change the password.
The fixed. Had to manually change the siteurl value in the table options in the remote database. Thank God...
-
When I was with the built-in webserver (EWS) to perform a backup, I get a message saying: "Year Error Has Occurred" and the printer would just lock up and flash lights and compel me to press the power button on the printer to reset.
I've done a few shrinking down and discovered that this happens only when the Scan-To-Email are selected to be included in the backup. I then discovered that it only happens when I have the email set to a (compressed) PDF Document Type Options.
I was able to get the backup to succeed by changing the options of Scan - To - Email Email Type of Document to PDF instead of PDF (compressed), then the backup succeeded.
In this case with the latest version of the firmware: CKP1CN1322CR.
Here's my printer information page (this could make this message other users to find more easily):
Product Name HP Officejet Pro 8600 N911g Product Model Number CN579A Service ID 23220 Firmware Version CKP1CN1322CR Country/Region USA
I couldn't find a place to submit a bug report, so I hope that this information gets to the right people.
Hmm, I tried this on my 8600 more Offcieejt and can confirm the same behavior, even though I have the firmware CLP1CN1322CR. I'll forward a link to this topic to some folks at HP who can be able to focus on this.
Nice work tracking down the details to replicate that.
-
Satellite Pro U300: No connection to the local network after updating BIOS 5.00 - WIN (Vista32)
Hello!
After the bios update newest to my Satellite Pro U300 (PSU31E) Lan Realtek adapter not working anymore. The map shows in Device Manager, but if I connect a cable, nothing happens (it says no cable connected).
ipconfig-all says:
Adapter Ethernet LAN connection:
Medienstatus...: En medium (disconnected)
Suffix-Verbindungsspezifisches DNS:
Description...: Realtek RTL8101 Family PCI - E Fast Ethernet NIC (NDIS 6.0)
Physical address: 00-1B-24-98-D7-AA
DHCP aktiviert...: Ja
Autokonfiguration aktiviert...: JaThanks for your advice!
Hello
In your case I would uninstall the Realtek LAN driver.
Can I visit the Realtek and download and reinstall the latest LAN driver.In addition, in the DOS command window, you can try to run this command:
* Ipconfig / renew *.PS: Try to also set the default BIOS too.
Concerning
-
PCMCIA card does not recognize the connection to the local network on Satellite Pro 4340
Hello world
I have 2 Satellite Pro 4340, running Win2K, SP4. I bought a card PCMCIA 10 / 100MB of Ultron (more or less no name :-))
When you insert the card, Win2k recognizes the card, but when the I plug the network cable, it does not recognize the connection. Cable is fine. It seems there is no power on the PCMCIA card. I read on some forums that there is a problem with the Topic100 Card Bus driver and voltage. I see that many people have the problem but not where to find the driver for the problem :-/ I couldn't find a driver on toshiba support site. A
ll have an idea, or better a link where I can download this driver? Any help is appreciated and thanks in advance for your help, support and answers.
CoreyIf this card needs a driver you will not find it on the download page of manufacturer of portable. You must check the card producer site.
As you know in the world of computers, it has set different standards. Produced very often cheap are not designed for these standards, and you can have different problems. I recommend you to use high quality products.
Maybe you are looking for
-
Satellite P-25 Audio CD will not play
Hey guys,. Looking for a little help. I have a Toshiba Satellite P - 25 series. My drive will read DVD and CD-ROM discs, but does not recognize audio CDs. I get an error message that says that there is no disc in the drive. I have rolled back the dri
-
I downloaded KB2459075 and its installation has failed several times? Help!
KB2459075 aDownload does not install!
-
BlackBerry Smartphones Startup2
A weird icon on my application selector named "sartup2". I restarted my laptop and nothing has changed, howa can remove this icon of my app selector?
-
BlackBerry smartphones help me! I want to download free applications
-
How to upgrade to Windows 7 Home Premium to professional?
I just bought a laptop with Windows 7 home premium and would like to 7 Professional using a computer drive nine full version I already have. How can I do this?