problem in my leptop

Similar Questions

• Hello I have a problem whit my battery

  Hello so as the topic title says I have a little bit of problem my battery leptop I'm all time I do not use the battery out then once weekly iv a replace Pentecost on the power pluged use until she hase 10% more and one House, then I plug in the power I load it 100% and I remove the battery. but now when I whanted to empty and load it again as always when I start the leptop or restart it I get this error when starting. can anyone help me with info about this problem? as it is not the first leptop iv you have this problem.

  Im very sorry for my bad English.

  My Leptop:

  Laptop HP Pavilion 15-e052sv

  Problem:

  Hi ADY9mm,

  Thank you for visiting the Forums HP's Support and welcome. I read your thread on your HP Pavilion Notebook 15-e052sv and get an error screen at the start of the internal battery. Try to check the RTC battery. Could be low and causing the time clock (RTC) incorrect real which would cause the error of the internal battery. Here is a document to show you how you can replace that.

  Hope that helps thanks for the screenshot of the error.

  Thank you.

• I had my leptop Internet cabel but that when I tried to conect wi fi on it did not a thing is a red cross on wirlass conection I have tride to resolve the problem, but no result me please halp

  so I tride to repearitbut everithing do not nothing

  How to configure WiFi...

  http://Windows.Microsoft.com/en-us/Windows7/setting-up-a-wireless-network

• Satellite 2520cds: problem BIOS - Bad checksum (CMOS)

  Hello

  I have an old leptop satellite 2520 CD.
  I have a problem with the BIOS and Cmos.
  I turn on ad after 3-4 seconds write me
  Bad checksum (CMOS) *.
  Before putting end to this problem I run the disk program to kill formad c d partion and I want to restart, start process of you XP installation cd.

  But he began to make this problem.
  So I decided to upgrade the BIOS
  I got my upgrade BIOS to version 8.0.
  I started the leptop but there is the same problem.

  Now, I can't enough F2 is not working.
  What can I do? Please help me
  Sam

  Hello

  The real time clock battery (RTC) feeding the clock/calendar internal and the maintenance of the system configuration settings.
  This error can occur when a machine is left off for a long period of time and is the result of a depleted battery for RTC
  So first step you should try to charge this battery.

  The RTC battery, plug in the adapter and turn on the computer.
  Leave the machine for about 24 hours to ensure a full charge in the RTC battery. Please note that the RTC battery will not charge while the laptop is turned off, the adapter is connected or not.

  In the configuration screen of the BIOS press the [Home] key to restore the default values, and then press the [End] key to save and exit, and then press [Y] to confirm and reboot the system.
  Then set the date and time in Windows

  As long as Windows starts, you will see an error message about an "invalid system time." Go ahead and click 'OK' to clear the error dialog box.
  Open Control Panel, and open the command 'Date and time' by double-clicking its icon. Set the date and time, then click OK to save.

• HP deskjet ink andvantage 1515: driver problem

  I have problem when I got the printer driver installed... it is working correctly

  but... after I stop my leptop. and turn it back on it, I'm trying to print driver error.......

  so I have to reinstall the driver on my OS...

  How to solve this problem permanently?

  Hi @zaeni ,

  I see that whenever you restart the computer, you must reinstall the driver again. I would really like to be able to help solve this problem.

  Most likely, the software is not completely installed correct or it is the installer of Windows causing a few problems.

  Download and run the Print and Scan doctor. It will diagnose the problem and could solve it automatically. Find and fix common printer problems using the tools of diagnosis HP for Windows?

  If you still experience problems, uninstall and download and install the latest software of the printer.

  The re-register Windows Installer first. Just do step 1 of the document please.

  Error: could not start the Windows Installer service. Do not take into account the title.

  Here's the latest drivers.

  HP Deskjet 1510 e-all-in-One Printer series full feature software and drivers.

  What were the results when you ran the Print and Scan Doctor? (she print or scan, error messages)

  If you need help, let me know.

  Have a nice weekend!
  Thank you.

• N100 random diferrent closing problem... RESOLVED (clik for solution)

  Hi, this is my first post...

  I bought a friend a Lenovo 3000 n100 0768-6vg(made in 06/08)

  It worked fine except for the drums, which I think he's dead...

  When I connect power cord the charge led flashes red once then green and stays like that for about 4-5 seconds... sometimes after a few minutes it starts to blink red as he is in charge, but he died iven after 20 minutes...

  in any case I don't mind the battery problem... the main thing as it sounds...

  I started the leptop and worked verry well, answered all the functions but I disliked the windows install so I installed a new copy then the problems started...

  He had originally Windows xp home edition and I wanted to install windows xp sp2, a new install...

  After installing windows, when I was a few steps to end install, the leptop suddenly shutted down

  now when I try to start windows, after 5-10 minutes it randomly stops

  Iven if I left it in bios mode it stops... I managed to get into windows and install SpeedFan to check temperatures and it is said that the cpu has aprox. 48-50 degrees celsius in normal mode...

  After a reboot I tried to stress him out and get a maximum of 60 to 65 degrees...

  I am desperate... I have tried averything... power without battery... no hard drive (with an xp live usb)...

  could someone help please?

  PS: I have experience in the repair of office but this thing is relatively new to me...

  an update of the bios could not solve my problem? : s

  I found the problem by a mistake ... .the how it happened

  I opened the leptop and close to the circuit of battery I saw something strange... I think that a liquid has managed to enter... I have only out cleanead and nothing... I removed the battery but still nothing...

  the solution I found sounds is like this:

  If you remove the battery charger wile it is still plugged, the 'bad' run will remain in the leptop through capacitors... Yes,

  Unplug the charger...

  Battery remov...

  leave it like that for 1 to 2 minutes wile pressing the power button (to drain run it), and then reconnect the charger without the battery...

  and voila, the liptop works fine without restarts and other animals

  I hope this will help others who encounter this problem... at least they can try this before taking the leptop at a service center

  Cheers!

• When I start my leptop Lenevo my cursor will not move and after clicking on a key sometimes it start to move...

  When I start my leptop Lenevo my cursor will not move and after clicking on a key sometimes it start to move... and when the window open an item on the top left most corner of the desktop is activated itself and any items on the desktop, I clicked on the selected item open... during this problem touchpad does not work when I press any key some time then he start working side effect... of this problem are

  (1) when we assume that slider in the middle of any page because of this problem just started automatically... Suppose that you read the number 10 on any book page and when that happens u don't come on the page no 1 automatically...

  what I've done

  I did a key recovery... even I am facing problem... Please tell me the steps to fix

  Original title: DESKTOP PROBLEM

  Hello

  Check with Lenovo support, their drivers and documentation online and ask in their forums
  on known problems.

  Support from Lenovo and downloads
  http://www-307.IBM.com/PC/support/site.WSS/homeLenovo.do

  Lenovo forums
  http://forums.Lenovo.com/

  Be sure to check that you have the latest driver for touchpad - updated or reinstall at Lenovo.

  =============================

  More troubleshooting if necessary:

  Error: Windows Explorer has stopped working
  http://support.Microsoft.com/kb/2694911

  Crashes Windows or freezes<- try="" these="" first="" and="" the="" methods="" do="" apply="" to="" your="">
  http://support.Microsoft.com/kb/2681286#method22

  Performance and Maintenance<- check="" these="" especially="" the="">
  http://Windows.Microsoft.com/en-us/Windows/performance-maintenance-help#performance-maintenance-help=Windows-7&V2H=win7tab1&V3H=winvistatab1

  Other methods of troubleshooting to use according to your needs:

  Use the startup clean and other methods to try to determine the cause of and/or
  eliminate problems.

  ---------------------------------------------------------------

  References to Vista also apply to Windows 7.

  What antivirus/antispyware/security products do you have on the machine? Include
  everything you've ALWAYS had on this machine, including those you have uninstalled (they
  remains of leave behind which can cause strange problems).

  ----------------------------------------------------

  Follow these steps:

  Try these to erase corruption and missing/damaged file system repair or replacement.

  Start - type this in the search box-> find COMMAND at the top and RIGHT CLICK – RUN AS ADMIN

  Enter this at the command prompt - sfc/scannow

  How to fix the system files of Windows 7 with the System File Checker
  http://www.SevenForums.com/tutorials/1538-SFC-SCANNOW-Command-System-File-Checker.html

  How to analyze the log file entries that the Microsoft Windows Resource Checker
  (SFC.exe) program generates in Windows Vista cbs.log
  http://support.Microsoft.com/kb/928228

  Also run CheckDisk, so we cannot exclude as much as possible of the corruption.

  How to run check disk in Windows 7
  http://www.SevenForums.com/tutorials/433-disk-check.html

  ==========================================

  After the foregoing:

  How to troubleshoot a problem by performing a clean boot in Windows
  Vista or Windows 7
  http://support.Microsoft.com/kb/929135

  Use advanced tools to solve performance problems in Windows 7
  http://www.howtogeek.com/HOWTO/6152/use-advanced-tools-to-troubleshoot-performance-problems-in-Windows-7/

  Problems with the overall speed of the system and performance
  http://support.Microsoft.com/default.aspx/GP/slow_windows_performance?p=1

  Optimize Windows 7 for better performance
  http://Windows.Microsoft.com/en-us/Windows7/optimize-Windows-7-for-better-performance

  Open the troubleshooter of Performance
  http://Windows.Microsoft.com/en-us/Windows7/open-the-performance-Troubleshooter

  To see everything that is in charge of startup - wait a few minutes without doing anything-
  then right click on taskbar - task manager - take a look at Applications.
  Process - Services - this is a quick reference (if you have a little box on)
  Lower left - show for all users, then check that).

  How to change, add or remove startup programs in Windows 7
  http://www.SevenForums.com/tutorials/1401-startup-programs-change.html

  Is a quick check to see who are loading method 2 - using MSCONFIG
  then after a list of these here.
  --------------------------------------------------------------------

  Tools that should help you:

  Process Explorer - free - find out what files, registry keys, and other objects
  processes have open, which DLLs they have loaded and more. This unique
  powerful utility will show you even owned by each process.
  http://TechNet.Microsoft.com/en-us/Sysinternals/bb896653.aspx

  Autoruns - free - see what programs are configured to start automatically
  When your system boots and you connect. Autoruns also shows you the complete list
  locations of registry and files where applications can configure start automatic settings.
  http://TechNet.Microsoft.com/en-us/sysinternals/bb963902.aspx
  Process Monitor - Free - monitor file system, registry, process, thread and DLL
  activity in real time.
  http://TechNet.Microsoft.com/en-us/Sysinternals/bb896645.aspx

  There are many excellent free tools from Sysinternals
  http://TechNet.Microsoft.com/en-us/Sysinternals/default.aspx

  WhatsInStartUP - free - this utility displays the list of all applications that are
  loaded automatically when Windows starts. For each application, what follows
  the information is displayed: Type of startup (registry/Startup folder), Command - Line
  Channel file, the product name, Version, company name, location in the registry or
  file system and more. It allows you to easily disable or remove unwanted programs
  that runs in your Windows startup.
  http://www.NirSoft.NET/utils/what_run_in_startup.html

  There are many excellent free tools to NirSoft
  http://www.NirSoft.NET/utils/index.html

  Window Watcher - free - do you know what is running on your computer? Maybe
  not. The window Watcher says it all, every window created by each execution of the statement
  program, if the window is visible or not.
  http://www.KarenWare.com/PowerTools/ptwinwatch.asp
  Many excellent free tools and an excellent newsletter at Karenware
  http://www.KarenWare.com/

  ===========================================

  Think about it an absolute must - manually update your drivers.

  Vista and Windows 7 updated drivers love then here's how update the most important.

  This is my generic how updates of appropriate driver:

  This utility, it is easy see which versions are loaded: run DriverView - set
  SEE drivers to hide Microsoft - update those with Dump in their names. (Also
  updated the BIOS and drivers from the chipset on the site of the constructor/the system motherboard).

  -Free - DriverView utility displays the list of all device drivers currently loaded
  on your system. For each driver in the list, additional useful information is
  Poster: load address of the driver, description, version, product name,.
  company that created the driver and more.
  http://www.NirSoft.NET/utils/DriverView.html

  For drivers, visit Maker as replacements and system manufacturer of device which are
  the most recent. Control Panel - write - graphics card - device manager
  the brand and complete model of your video card - double click - tab of the driver-
  Note the version information. Now click on UPdate Driver (this can do nothing
  MS is far behind the certification of drivers) - then do a right click - Uninstall - REBOOT
  This will refresh the driver stack.

  Repeat this for network - card (NIC), Wifi network, sound, mouse, and keyboard
  If there are 3rd party with their own software and drivers and the other main device drivers
  you have.

  Now, go to the site of the manufacturer of system (Dell, HP, Toshiba as examples) (restore)
  and site (Realtek, Intel, Nvidia, ATI, for example) and get the manufacturer and device
  their latest versions. (Look for the system to update the BIOS, Chipset and software updates
  Site of the manufacturer here.)

  Download - SAVE - go to where you put them - right click - RUN AD ADMIN -.
  REBOOT after each installation.

  Always check in the Device Manager - drivers tab to be sure the version you are
  installation actually appears. This is because that some rollback of drivers before the
  later is installed (particularly that audio drivers) so install a driver - reboot.
  Make sure that it is installed and repeat if necessary.

  Repeat to the manufacturers - BTW to the device makers DO NOT RUN THEIR
  SCANNER - check manually by model.

  Look at the sites of the manufacturer for drivers - and the manufacturer of the device manually.
  http://pcsupport.about.com/od/driverssupport/HT/driverdlmfgr.htm

  Installation and update of drivers under Windows 7 (updated drivers manually using
  the above methods is preferable to ensure the latest drivers from the manufacturer of system
  and device manufacturers are located)
  http://www.SevenForums.com/tutorials/43216-installing-updating-drivers-7-a.html

  If you update the drivers manually, then it's a good idea to disable driver facilities
  in the updates of Windows, which leaves on Windows updates, but it will not be installed
  pilots who are generally older and cause problems. If updates provides a new
  driver then hide it (right click on it) and then go get new ones manually if
  you want.

  How to stop Windows 7 automatically install drivers
  http://support.Microsoft.com/kb/2500967

  ===========================================

  Refer to these discussions because many more excellent advice however remember to check
  your antivirus, the main drivers and BIOS update programs and also to solve problems
  with the first method cleanboot.

  Problems with the overall speed of the system and performance
  http://support.Microsoft.com/GP/slow_windows_performance/en-us

  Performance and Maintenance Tips
  http://social.answers.Microsoft.com/forums/en-us/w7performance/thread/19e5d6c3-BF07-49ac-a2fa-6718c988f125

  Explorer Windows stopped working
  http://social.answers.Microsoft.com/forums/en-us/w7performance/thread/6ab02526-5071-4DCC-895F-d90202bad8b3

  I hope this helps.

  Rob Brown - Microsoft MVP<- profile="" -="" windows="" expert="" -="" consumer="" :="" bicycle=""><- mark="" twain="" said="" it="">

• Unable to Scan to the computer after downloading macOS Sierra. Is this a software problem?

  How can I scan from HP Envy 4500 to computer after downloading macOS Sierra?

  Hello wdemetris,

  Thanks for asking for scanning helps here in the Apple Support communities. I understand how it is important to have access to your scanner and am happy to offer help for this.

  As a precaution, we always recommend that you have backups to make sure that all your data is safe. You can perform a backup using Time Machine and an external hard drive. Use this article to help make a backup of your Mac: use Time Machine to back up or restore your Mac.

  Then, in accordance with article help: printer and scanner for Sierra, El Capitan, Yosemite, and the Mavericks macOS software, the HP Envy 4500 e-all-in-one is supported for printing and scanning. The drivers must be installed, but if not, if it please go to the App Store and check the updates tab to see if there are updates for HP. If there is, please install.

  If you have only general questions about how to get your updated scanner in place or how to scan pictures, please check out these two articles: macOS Sierra: implement a scanner & macOS Sierra: scan images or documents. If everything is configured correctly and you still have problems scanning, please visit this help article: macOS Sierra: scanning troubleshooting.

  Thanks again and have a great rest of your day.

• My iPhone 6 installed 10.0.2 stops when it gets to 40% of autonomy.  In addition, it seems to pass power WAY to fast with the new software.  Does anyone else have this problem?

  My iPhone 6 installed 10.0.2 stops when it gets to 40% of autonomy.  In addition, it seems to pass power WAY to fast with the new software.  Does anyone else have this problem?

  Hello brooksm549,
  Thank you for using communities of Apple Support.

  I got your message which, since updating your iPhone 6 to iOS 10.0.2 your iPhone stops when it is 40% and the power to empty very quickly. I understand your concern with the iPhone turn off and drains the battery. I recommend you to review the use of the battery to see what app contributes more to the battery drain. The following article will provide you with steps on how to check the use of the battery:

  On the use of the battery on your iPhone, iPad and iPod touch

  When you know about the soft uses more battery, you can change your settings in order to optimize the battery life:

  Maximize the life of the battery and battery life

  Best regards.

• MacBook Pro display problem

  Hello members of the community.

  As of recently, I have noticed some glitches when feeding on my MacBook or awakened from his sleep.

  The colors are distorted, usually with pink, green, or yellow blobs. Blobs cannot entirely replace the colors, they appear to be contained in a element would normally be. For example. the menu bar will be partially pink and white, but pink does not leave the menu bar in this area, and the Office has green lines on it.

  I tried to take a screenshot, but the problem resolves in about 20 seconds, but it's a recurring problem.

  It happens when I wake up, connection or not. I had also certain powers serious and problems of performance, such that my MagSafe LED would not illuminate when plugged on rare occasions, fan could turn unnecessarily, graphics performance were SUPER slow, and the health of my battery was running out quickly. I actually ran a report on the system at 2 different times and my quality of full load is depleting of 1.2% per charge cycle, which is very worrying. I went from 6281 mAh mAh 6138 maximum capacity after two cycles of load. I'm tracking closely it because at this rate, my battery will survive only at load cycles about 150 instead of the 1000 expected, gives me the idea that this could very well be a bad battery. The computer is also warm to the touch while you sleep, not connected to the power supply. I NAP active but even taking into account should not be hotter my iPhone did the same thing.

  I have reset the SMC, and it solved a couple of problems. The charger works fine now and my performance improved considerably (which made me feel better, either it is a high-performance laptop, a 11-inch MacBook Air should not he surpass), and battery life has improved. I feel even if it uses a lot of power in his sleep. Maybe I need to turn off the NAP and see if that makes a difference. The graphic bug still persists however, and I don't have enough time to see if the max battery is depleting again.

  In regards to the bug, is there something that can be done? Basically, I want to assure you that I took all appropriate measures or if someone else has this problem to see if it can be software related instead of my computer.

  I have the entry level MacBook Pro with the retina, last generation.

  Any constructive contribution welcome!

  See you soon.

  -adreaux

  Hello bernardn753,

  After reviewing your post, it seems that you are having problems with the screen showing strange things on it. Looks like you already have a troubleshooting. I recommend you read this article, as reset NVRAM would be to reset your screen resolution settings that should help.

  How to reset the NVRAM on your Mac.

  Thank you for using communities of Apple Support. Good day.

• with IOS 10.0.2 - 5s iphone Bluetooth problems

  Since upgrading ISO 10.0.2 my M50 from PLT Plantronics (helmet unique headset) do not reliably connects with my iPhone 5 more. I have to go to the settings, activate bluetooth turned off/turned on, touch the device on the bluetooth page, etc. Once it connects successfully, it will reconnect (if I turn off the headset and turn it back on) for a short period. The next day he does not connect itself but I play with bluetooth on the iPhone again.

  It has always worked perfectly before the 10th of IOS.

  And, as I noticed others mentioning, the volume is much lower with IOS 10. The maximum volume is much lower. I can barely hear it now, more normal background noise, while driving.

  I did:

  Forget this device for the PLT M50 and paired again (several times)

  I did a Reset Network Settings

  I don't know what else to do - but it's a 10.0.2 IOS issue.

  Hello AppleUser2k,

  Please ask questions about your problems of connection between your iPhone and your Plantronics headset since you upgraded to iOS 10. I understand how important it is to have your Bluetooth devices connect with your iPhone with reliability. Here's what I recommend.

  The first thing we want to make sure is that all your data is safe. You can perform a backup in iCloud or iTunes using this article: backing up your iPhone, iPad, and iPod touch.

  Once your data is safe, try the troubleshooting steps in this article to help: get help to connect a Bluetooth accessory with your iPhone, iPad or iPod touch device should also check with the manufacturer that the device has all the drivers and firmware to work with the new version of iOS.

  If you have checked everything and that you have installed the latest firmware or driver and always are problems, please be aware of your surroundings when you encounter these problems. If you can isolate the time or location, you see the problems, you can isolate the cause. You can even see this help article to ensure that you are not affected by outside interference: the potential sources of Wi-Fi and Bluetooth.

  Thanks again and have a great rest of your day.

• Problem after update 10.0.2 iOS iPhone touchscreen

  After I have updated to iOS 10.0.2, I noticed a problem with the touch screen. Using the position of the image on the right side, near the corner, the toushscreen does not work.
  For example: when you use the keyboard, I can't type the letter 'P', have trouble typing BACKSPACE. Using the Contacts app, I can't scroll through using the alphabet bar.

  Do what idea of the problem?

  Kind regards!

  Hi fabriciorela,

  Thanks for the upgrade to iOS 10! I understand that the right of your screen is unresponsive to the touch. You can try the steps in this link to fix the problem. If the screen of your iPhone, iPad or iPod touch does not respond to touch

  If it does not help the problem, try to restore the device to factory settings. I would like to backup your important data first.

  The backup of your iPhone, iPad and iPod touch

  Use iTunes on your Mac or PC to restore your iPhone, iPad or iPod to factory settings

  Please use the Apple Support communities to post your question. Let us know how it turns out. Have a great day.

• Bluetooth connection problem iPhone - audio system Nissan after upgrade iOS10

  After iOS10.0.2 iOS9 on iPhone upgrade, I got a cordially problem receive calls raise Nissan car audio.

  I can make a call without any problem. Bluetooth connection is stable. I can download address book e.t.c. But I can't receive a call. I see the incoming call on the radio shows. After pressing the button "answer" on the car Audio System, audio between iPhone and Audio streams car breaks down.

  But the cellular connection remains active. I need to rotate the audio output on the screen of the iPhone car for iPhone and back to the car. After that, I can continue my call via the car radio.

  Thanks in advance

  Hello StasV,

  Thank you for using communities Support from Apple. I know having a problem with calls on your iPhone in your car, it's not what you expect. The good news is that these steps will be useful for your problem of phone calls while using the bluetooth in your car. Go to settings > general > accessibility > routing of Audio calls and the value headset/Bluetooth Headset and retest your question.

  Audio routing call - the iPhone user Guide
  Help to connect your iPhone, iPad or iPod touch with your car radio

  See you soon!

• 2 iphones on one iTunes, problem of photo icloud account

  OK, my brother-in-law just updated its OS on his Iphone. He shared an Apple ID with his wife, who has his own iPhone. They all have two backup only in iCloud. His problem is that his wife photos are now on his phone. How can he fix it?

  Get its own identifier Apple- create and start using a Apple - Apple Support ID

• Problem activation ISO 10 September 2016

  After my Ipad iOS 10.0.2 update I could not activate because it says I am not access with the original Apple journal. Makes no sense. I bought the new Ipad in seven of 2013 Dabs.com. She has been linked to my Apple account 10 days ago (I deleted my profile by own Apple support Web site suggestion as a way to fix my problem, the other restoration/upgrade to the Ipad with ITunes update). I contacted the support of Apple (I have two numbers in case Apple). Asked Apple support to provide a proof of purchase I made. Told me now the reception that I provided does not correspond to my Ipad, but Apple isn't going to help with all the details to help to regularize the situation. The Ipad is mine and well was linked to my account from the date of purchase in September of 2013 until I removed it at the suggestion of site specific help from Apple. I now do not have access to my ipad £460 for more than 10 days and have lost money and time talking to 4 different cooperatives of Apple, after 6 calls and none seem able to deal with a ridiculous situation. Alexandre Vitorino (Apple) seems to have the best handle on weird how this situation is. Please can someone fix this? A software update on an Ipad that I own shouldn't stop me using it and then force me to prove that I admit actually before I use it again! I'm a professional businessman who uses it for meetings of the Council. I have a receipt for my camera and get treated like a kind of criminal.

  My sincere sympathy for those who can't find their original receipt or forget their original log-in Ipad because Apple does not help, you and your Ipad will be also useless mine is currently!

  If you are in the same situation please confirm to this post. I can't be alone, if she feels like it!

  Post edited by: cibble10

  Lock activation occurs when the ID of original Apple blocking it does not match with your current Apple ID.

  Until you can bring a receipt valid from an Apple reseller or authorized, it's nothing you can do.

  BTW, the polling stations in this Apple-owned forums is prohibited. You can review the terms of use.