Problem of Time out of workflow

Similar Questions

• VISA Read.vi time-out

  Hello

  Recently I happened to use Labview drivers of NewPort (ESP301) and Lakeshore (Lsci218) and I encountered the same problem of "time out" every time that a Subvi driver called VISA Read.vi for serial communication.

  I first thought has problems with driver Labview provided by the manufacturers, but after trying the pilot different LV from different companies, I started to think that the problem might be the Read.vi VISA itself.

  I use LV2010-spring, also tested with LV2011SP1. Both give the same timeout problem.

  I asked businesses about the problem, they have not found answers, nor they have LV2010 or LV2011.

  Someone had the same problem?

  Screw joint are FYI for what I tested.

  'test initialize.vi 218' is 218 Lakeshore pilot, with a change of the addition of "\r\n" in the "* IDN? the Subvi called VISA Read.vi. and a timeout error.

  "test initialize 218 - md2.vi ' has the same function, but call VISAWriteRead.vi instead of VISA Read.vi. and works OK.

  How can I know that the VISA Read.vi in LV2010 or LV2011 works correctly? or can I replace the VISA Read.vi with LV8.6 one?

  It seems to me that Newport and pilot LV lakeshore have been developed under version LV does not exceed 8.6. and I think that they tried their driver before release or I hope.

  any suggestion is appreciated.

  Xiaofeng

  The version of LabVIEW is not relevant.

  In the read/write, you add the LF/CR. In the other, you add CR/LF.

  Avoid platform dependent end consistent line in the communication of the instrument.

• Time-out in the workflow

  Hi all

  I am new to Oracle Workflow. I am facing problem when I put the Notification time-out feature.

  Approve and reject functionality does not work as expected.

  I put the time for 2 Minutes.

  and my notification package is as below,

  If funcmode = "RUN" then

  Insert the script - good job (it is inserting only when I select to approve or reject, not sure why it doesn't work when timeout)

  end if;

  If funcmode = "TIMEOUT" then

  Insert the script - don't DO NOT WORK
  end if

  If funcmode = 'REPLY' then

  If result = "APPROVED" then

  ... good job

  elsif result = "REJECTED" then

  ... good job.

  on the other

  ......

  end if;

  end if;

  I need to insert into a table, when the time came.

  Please tell me how to do?

  I thank in advance.

  Kind regards

  UVA.

  Are you sure that you have completed the engine in background once expired the time-out? I mean, not because two minutes have passed is the activity considered as expired. You must run the background engine for the activity has expired. He's there when the funcmode = "TIMEOUT" will be used.

  You can use the wfengchk.sql script to check whether the activity has actually expired.

  Kind regards

  Alejandro

• Increase the time-out value of external WF stubs in vRA 6.2 device?

  The stubs of external workflow (BuildingMachine, MachineProvisioned, etc.) are defined to use a time-out of 30 minutes by default. It seems that other people change delays via a XML configuration file (see "example XML configuration file" in this post: Creation of Workflows for change state), but all of the examples use a Windows Setup and the file does not exist in the device of vRA.

  Does anyone know how to set timeouts, perhaps through custom properties or something?

  Thank you.

  Someone else has this problem, I found the file. The XML file is the server of IaaS in the following location: C:\Program Files (x86)\VMware\vCAC\Server\ExternalWorkflows\xmldb\ExternalWFStubs.xml

• error message "kauth resolver external time out."

  Hello

  Pay my iMac (21.5 inch, end of 2013, 2.7 GHz Intel Core i5 processor) bought with Maverick, I went successively to Yosemite and then to El captain. And since then, I have a problem starting not to power: the progress bar stuck at 60%. Start-up in Verbose mode, I get the message "kauth resolver external time out."

  The only solution is to "turn off, is dry, and tension to under 30." This second time under tension, the mac restarts. A solution that is not terrible.

  I used OnyX, but no verification has failed to solve the problem, everything looks ok.
  Who has a solution pour troubleshoot this problem?

  Thank you for your help.

  I too have this problem sporadically with some of our iMacs us upgrades 10.11.3 (from 10.10).  By chance are your iMacs have records of merger?

• A time-out of the finite queue of wiring allows parallelism?

  I have several loops (11) all running in parallel, set up with a producer--> several consumer-> multiple consumer architecture.

  In each of the loops of consumer, I wired the values of time-out on the order of 1 second each of the vi "remove item" which feed on each loop. However, the overall performance of all vi is very slugish.  I have no expectation s vi in the loops of consumer, I guess the time queue supports this feature and allows labview to work its magic of parallelism. This hypothesis is correct?

  For what it's worth, the loop of the producer bed synchronously large shared memory double paintings representing the acquired data and post processed in RT through virtualization (hypervisor). The loop of producer implements an element of expectation. This loop of producer distributes the data to the various queues, depending on the data type meta code embedded in the data of recevied. Then, first consumer level loops review data, update some PLC tags accordingly (via the datasocket connection) and, under certain conditions, send signals well formatted the next level consumer loops that manages storage PDM.

  Each consumer has a dedicated queue and each of them are powered by several producers to the top of the pipe. I put vi waiting in each loop of consumer with a value of about half of the time waiting for data to arrive, and it did not help at all. However, the problem has been resolved by configuring the properties of execution of almost all under vi as priority of subroutine, returning with dedicated allocation of memory. I know it's basic stuff that I should have checked before hand, but everything works fine now.

  Thanks for the help anyway!

• Time-out in the structure of the event

  Hello

  I try to configure the time-out period in the structure of the 5s event using the loop, as shown in the picture as an attachment. The problem is that this time-out event occurred only when I code debugging and does not happen when I run the same without debugging. Any suggestions on this?

  Thank you!

  OK, just use VISA Read to read the first three octets.  Then do another set VISA Read the number of bytes defined in dlen.  If the data does not, then you will get a VISA expiration time.

  

• smart camera of the trigger of the time-out value of the error - VBAI 3.6

  Hello that tal?, el tema are that I have a problem with the Smart camera're tengo una fotocelula conectada has the patilla of trigger and (2), el u Trigger-(12) masa in las patillas del conector DB15 of the smart camera para as cuando PASE una pieza realice the fotografia. The cuestion are el solo time-out error me already poner 60000 ms, y for example, so una pieza soon en pasar 60000 ms en el paso of the closing of imagen mas me pone time-out error, y sigue por el diagrama of blocking como if would Fall the imagen. In principio imported me that salga el time-out error, pero me gustaria that esperase has the following pieza sin avanzar por el diagrama of blocking, not so to me explico very well.

  If alguien tiene alguna idea como el problama delivery could be lo agradeceria mucho.

  Cordially, is muchas gracias of photos. David.

  Hey David,

  entonces Perfecto. If the respond you vale marcala como tal in el foro o con UN kudo en knew defecto para as other users themselves can the answer is beneficiar.

  Duro con ello!

  Jesus.

• time-out error

  Hello

  I get an error of delay in my exe file but its not working in laptop but its does not work in desktop basically I m do mannully x and axis are using servo motor control first meters in mannully and I'll store data and after I'll are automatically at the time where I get error of wait time at the office. In the same office before it was working now its time-out error is. Please tell me the solution. actully I change office in this office than m... timeout error please tell me the solution.

  Thank you.

  Hi, I had the answer... I solved the problem of my problem, I have already mentioned above (in his work at the office laptop its does not work) Finally I solved the problem is (I use delta servo motor control, I was using the communication cable connection is not based) in connection only. Finally I gave the connection now its fantastic work...

  Thank you for your review of precious...

• PCIe-1429 randome time-out errors

  I use a card National Instruments PCIe - 1429 Camera Link which gives timeout errors about 20% of the time every time that the show clock is stopped and restarted.

  The problem I see occurs for a 1-tap 16-bit and 8-bit 8 - tap camera configuration.  Every time the camera changes modes show link camera clock is momentarily interrupted, and PCIe-1429 is unable to acquire an image of 20% of the time.

  In Measurement & Automation Explorer, it returns the error: "a timeout error has occurred while you wait for the specified event.  If you expect a picture, make sure all the video data is acquired during the period.  If you wait for a signal, check that the assertion of signal occurs within the period.

  Now, I know that my timing is correct because if I simply stop the clock to show again the PCIe-1429 will begin to acquire images.  He was to acquire and then always correctly the images until the next time the clock of transmission is interrupted.  It is on a probability of 20% of a timeout error if the clock of transmission is interrupted.  It behaves like the phase PCIe-1429 liaison camera receiver locking loop has re-synchronization problems.

  Our camera (an intern built Kodak) uses the National Semiconductor DS90CR287 channel link transmitter.  When the PCIe-1429 gives a timeout error, I check the clock of transmission DS90CR287 on an oscilloscope and it looks always good.

  Is this a known issue with the PCIe-1429 or a known sender of DS90CR287 problem?

  Apparently, there is a bug in the DS90CR287 channel link serializer.  The phase lock loop, sometimes fails to produce a clock output series of acquisition card and the operating cycle if the input clocks are interrupted.  A phase lock loop should be able to recover from that.  We noticed that National Semiconductor changed their sheets to require power cycling the DS90CR287 after all of the input clocks are interrupted.  We have implemented the procedure of power cycle and time-out errors now appear to have stopped.

  All fixed!

• Using the MS ODBC driver to connect to Oracle and MS SQL DB - get a time-out error

  I have the driver installed and configured on the Linux host where sits the Oracle DB.  I worked through the configuration and tested along the way.

  If I execute the following SQL statement I get a timeout error after only 15 minutes:

  SQL > select * from host_table@UCMDB806;

  Select * from host_table@UCMDB806

  *

  ERROR on line 1:

  ORA-28511: interruption of the RPC connection to heterogeneous remote agent to help

  SID = ORA-28511: lost RPC connection to heterogeneous remote agent to help

  SID = (Description = (Address = (Protocol = TCP)(Host=localhost) (port = 1521)) (CONNECT_DAT

  A = (SID = UCMDB806)))

  ORA-02063: preceding the line of UCMDB9

  Process ID: 4070

  Session ID: 392 serial number: 40935

  If I limit the SQL to give hosting me only that start with 'a', I get this:

  SQL > select * from host_table@UCMDB806 where (name) lower like 'a % ';

  ID

  ------------------------------------------------------------

  NAME

  --------------------------------------------------------------------------------

  TenantID

  ------------------------------------------------------------

  name of the vendor

  --------------------------------------------------------------------------------

  softwarename

  --------------------------------------------------------------------------------

  4616

  AHOST-B

  76436

  ID

  ------------------------------------------------------------

  NAME

  --------------------------------------------------------------------------------

  TenantID

  ------------------------------------------------------------

  name of the vendor

  --------------------------------------------------------------------------------

  softwarename

  --------------------------------------------------------------------------------

  SYMANTEC

  .

  .

  .

  It seems to be a time-out on this query.  My software is located 20 minutes for a query.  MS SQL server is set to unlimited for remote queries (we did it to help isolate the timeout).  So, I guess the wait time that is happening at the level of ODBC driver.  Someone has all understand how to solve this problem?

  Hello

  Your question is beyond the scope of this community.

  Please repost your question in the SQL Server TechNet Forums.

  https://social.technet.Microsoft.com/forums/SQLServer/en-us/home?category=SQLServer

  See you soon.

• Windows Server 2012 R2 Request Time Out

  I installed Oracle Linux 7 use of Hyper-V on Windows Server 2012 R2. When I connect the Oracle Linux for internet (parameters--> network--> then set the device to run the internet), Oracle Linux takes the entire internet server and also indicates "Request Time Out" while that ping using command line on Windows server.

  Is it possible that I can fix this or can anyone help me solve this problem? Very Important and Urgent. Please help me.

  Hello

  Post your question in the TechNet Server Forums, as your question kindly is beyond the scope of these Forums.

  http://social.technet.Microsoft.com/forums/WindowsServer/en-us/home?category=WindowsServer

  See you soon.

• Why my network time-out when you try to download the update for ipod?

  I keep trying to download Ipod software version 5.0.1 which takes about 2 hours, but after an hour or two, says network error message has expired. I checked all the settings that I found but nothing helped.

  Hello

  I removed the suggestion of Brian Tillman on the accounting in the Forum Feedback since I went ahead and moved this thread in a forum more appropriate responses.

  However, I still agree with his second suggestion to ask in the forums of Apple. As you mention that this problem occurs by updating your iPod, I think there must be a problem with her or with iTunes which is at the origin of the network to time out.

• Time-out error when you try to calibrate a PXI-6552 using Calibration Executive.

  I make a mistake I never saw elsewhere trying to calibrate a PXI-6552 using Calibration Executive. We have been calibrating these cards for 3 years and never had a problem. The error I get has to do with the HP 3458 A DMM taking a reading.

  1074126845 error occurred at IviDMM Read.vi in audit generation step voltage
  The possible reasons: maximum time state of the driver (Hex 0xBFFA2003) exceeded before the operation is complete.
  The primary error: (Hex 0xBFFF0015) timeout expired before the operation is complete.

  As soon as Cal Exec implements the PXI-6552 module then will take a reading of the 3458A what an SRQ message on the 3458A, then the error message above appears in Cal Exec. I tried to reinstall the drivers OR DMM. The voltage on the meter screen is good for the first stage (5.5 volts DC), but it times out and gives me the error as indicated.

  Nevermind, I got the latest drivers and install and everything works fine now.

• Windows XP is very slow and auto update works but when I try to run internet explore the system times out. »

  Original title: Windows XP runs very slow

  Windows XP is very slow and auto update works, but when I try to run internet explore the system times out.

  Hi Bill,

  Thanks for posting your question in the Microsoft Community.

  I imagine the inconvenience that you are experiencing. I will certainly help the question of fixing.

  To help you suggest several steps to solve the problem, I would appreciate if you could answer the following questions:

  1. What is the error message that is accurate or complete?
  2. have you made any recent hardware or exchange of software on your computer before the show?

  Please follow the links below and check the issue:

  Maintenance tasks that improve performance:
  http://Windows.Microsoft.com/en-us/Windows-XP/help/Setup/maintenance-improve-performance

  Slow PC? Optimize your computer for optimal performance:
  http://www.Microsoft.com/athome/Setup/optimize.aspx#fBid=R7qdKIMaJyT

  Warning of Chkdsk.
  Important: when running chkdsk on the drive hard if bad sectors are found on the disk hard when chkdsk attempts to repair this area if all available on which data may be lost.
  WARNING: Reset Internet Explorer settings can reset security settings or privacy settings that you have added to the list of Trusted Sites. Reset the Internet Explorer settings can also reset parental control settings. We recommend that you note these sites before you use the reset Internet Explorer settings.

  Note: The data files that are infected must be cleaned only by removing the file completely, which means that there is a risk of data loss.

  Internet Explorer is slow? 5 things to try:
  http://Windows.Microsoft.com/en-us/Windows/help/Internet-Explorer/slow-five-tips-to-boost-performance

  Warning: Reset the Internet Explorer settings can reset security settings or privacy settings that you have added to the list of Trusted Sites. Reset the Internet Explorer settings can also reset parental control settings. We recommend that you note these sites before you use the reset Internet Explorer settings.

  Your response is very important for us to ensure a proper resolution. Please get back to us to help you accordingly.