Problem of VeriSign

Similar Questions

• Problem of CA with NAC

  Hello

  I use internal CA (Microsoft Win 2003 CA) to provide SSL certificates to the NAC. The problem is that end users are still getting warnings on connection to the network in the same way as when I used the Perfigo certificate. I tried to install the certificate from the server to the clients, but CA is always seems to be unreliable. Does this mean I have to buy certificates of authorities of confidence like Verisign, or still there is something I can do for my CA? Help, please.

  Kind regards

  Sybille.

  Sybille,

  If you click this link, it allows you to download a said cert?

  If so, take this file to the client and double-click it. It should automatically install in the correct store.

  HTH,

  Faisal

• Configuration problem TELL!

  Hello

  I am facing a problem in the client configuration SAY for external suppliers. TELL works well for them in the PROD environment where SSL is not yet activated. In the scene environment when I try to connect to the server (https) after the initial Setup, it fails with the error "the connection with the server could not be established.

  Stadium:

  1. Environment node two - UCM 10 g

  2 LB in place with SSL

  3 SAY 11 g

  Receive try connecting the content server via SAY use single node url and it works very well in phase. Also the domain users have been able to establish a connection using SSL LB url.

  In the browser when they try to connect stage SSL url they are facing an exception link "Continue on this site do not recommended", after agreeing, they were able to access the content server.

  Please tell me why the url https LB is a failure for external users only.

  Thank you

  Easy.  The certificate being presented to the user is not coming from an approved certification authority.  Apparently, you have an internal certification authority who issued the certificate, and this internal authority is known for your internal users, but not for external users.  Having the external user add your internal certification authority to their certificate trust store, or buy a certificate for balancing of load of a known certificate authority, such as Verisign or Entrust.

• Alignment problem signature blocks

  I created the form and add the signature blocks on the lines where I want each of the parties to sign.  However, once I have save and send to the signing, Adobe exports only the signature at the bottom of the last page blocks.  In other words, I put a signature block on a specific line for a specific signature, it looks good in the preview, but when I send the document, Adobe has moved the signature blocks at the bottom of the last page, in order of email. Any suggestion would be useful before I turn to VeriSign or another program.

  HiRNashville,

  While placing the form fields in the environment of EchoSign, please check field for the alignment of the fields to the page layout.

  Check to see if it help you solve the problem.

  

  Kind regards
  Nicos

• Impossible to obtain Verisign Signature validated in Acrobat

  For the last six months, I was able to get my digital signature Verisign validated in Adobe Acrobat format. Just today, I renewed my Verisign certificate for another year. I saved the certificate on my hard drive using a password to fix it. When I certify a my signature on a document, the resulting signature icon says "...". invalid persona"and the icon in the upper left corner (the head and shoulders of a person) has an exclamation mark on it.

  I am frustrated trying to figure out what is wrong. Any suggestions would be greatly appreciated.

  Hi Mike,.

  Acrobat (and when I say Acrobat Acrobat and Reader time) it is sufficient to establish a valid string. If you have selected one of the root certificates as the anchor of trust and that the signature is valid, then you're done. One thing I suggest you do is to ensure that all certificates below the anchor of trust have the revocation information. In the view of the certificate dialog box, you can select the revocation tab. As you highlight (select) each cert below the anchor trust you should see information in the Details window on the revocation information. If the text says that it is missing or there are problems let me know, otherwise you are good to go.

  Either way, you might be able to uncheck display all found certification paths (above the window where you see three identical channels) and then you will see only the a string that uses Acrobat. That could help to simplify things.

  Finally, it would be great if you could mark the thread as answered (that is, only if you feel the question was answered) to help other people looking for the forum close to the bottom of what you have to look.

  Thank you

  Steve

• CFHTTP or webservice to Verisign SSL

  I tried many things on getting this work, and I come to the same conclusion at each end... IT simply doesn't get it.
  
  If I try to connect to a site using SSL with CFHTTP or via cfinvoke, I get a result like this:
  
  struct
  Charset [empty string]
  ErrorDetail I/O Exception: peer not authenticated
  FileContent connection failure
  Header [empty string]
  MimeType unable to determine the MIME type of the file.
  ResponseHeader struct [empty]
  
  StatusCode connection failure. Not available status code.
  Text YES
  
  In my case, I try to connect to a Verisign Class 3 certificate. I went to verisign, downloaded the current intermediate certificates, install them using the keytool utility, rebooted my machine, re-tested, did not work. I have installed the keys through MMC in windows, did not work. I also tested with Godaddy ssl key... does not always work. I have read just about every post in the forums about this, and none of them never seemed to have the problem resolved. I have a box with 7 and 8.01 and I've tried it on both boxes, and none of them had set. My installation 8.01 running jvm 1.6, which was supposed to have this fixed number... I am at a loss here...
  
  Has anyone fixed this problem?
  

  Surprisingly, I found the snipped below on livedocs.

  Please note that I was on my own dedicated server Windows to which I had access command prompt, so that I could perform the commands below. It's the only thing that worked for me.

  http://livedocs.Adobe.com/ColdFusion/8/htmldocs/help.HTML?content=Tags_g-h_09.html

  Manually import a certificate

  Go to a page on the SSL server in question.
  Double-click the lock icon.
  Click the Details tab.
  Click on copy to a file.
  Select the base64 option and save the file.
  Copy the REB in C:\CFusionMX7\runtime\jre\lib\security (or if it uses ColdFusion JRE).
  Run the following command in the same directory (keytool.exe is located in C:\CFusionMX7\runtime\jre\bin):
  keytool-import - keystore cacerts-alias giveUniqueName-file NomFichier.cer

• Unable to Scan to the computer after downloading macOS Sierra. Is this a software problem?

  How can I scan from HP Envy 4500 to computer after downloading macOS Sierra?

  Hello wdemetris,

  Thanks for asking for scanning helps here in the Apple Support communities. I understand how it is important to have access to your scanner and am happy to offer help for this.

  As a precaution, we always recommend that you have backups to make sure that all your data is safe. You can perform a backup using Time Machine and an external hard drive. Use this article to help make a backup of your Mac: use Time Machine to back up or restore your Mac.

  Then, in accordance with article help: printer and scanner for Sierra, El Capitan, Yosemite, and the Mavericks macOS software, the HP Envy 4500 e-all-in-one is supported for printing and scanning. The drivers must be installed, but if not, if it please go to the App Store and check the updates tab to see if there are updates for HP. If there is, please install.

  If you have only general questions about how to get your updated scanner in place or how to scan pictures, please check out these two articles: macOS Sierra: implement a scanner & macOS Sierra: scan images or documents. If everything is configured correctly and you still have problems scanning, please visit this help article: macOS Sierra: scanning troubleshooting.

  Thanks again and have a great rest of your day.

• My iPhone 6 installed 10.0.2 stops when it gets to 40% of autonomy.  In addition, it seems to pass power WAY to fast with the new software.  Does anyone else have this problem?

  My iPhone 6 installed 10.0.2 stops when it gets to 40% of autonomy.  In addition, it seems to pass power WAY to fast with the new software.  Does anyone else have this problem?

  Hello brooksm549,
  Thank you for using communities of Apple Support.

  I got your message which, since updating your iPhone 6 to iOS 10.0.2 your iPhone stops when it is 40% and the power to empty very quickly. I understand your concern with the iPhone turn off and drains the battery. I recommend you to review the use of the battery to see what app contributes more to the battery drain. The following article will provide you with steps on how to check the use of the battery:

  On the use of the battery on your iPhone, iPad and iPod touch

  When you know about the soft uses more battery, you can change your settings in order to optimize the battery life:

  Maximize the life of the battery and battery life

  Best regards.

• MacBook Pro display problem

  Hello members of the community.

  As of recently, I have noticed some glitches when feeding on my MacBook or awakened from his sleep.

  The colors are distorted, usually with pink, green, or yellow blobs. Blobs cannot entirely replace the colors, they appear to be contained in a element would normally be. For example. the menu bar will be partially pink and white, but pink does not leave the menu bar in this area, and the Office has green lines on it.

  I tried to take a screenshot, but the problem resolves in about 20 seconds, but it's a recurring problem.

  It happens when I wake up, connection or not. I had also certain powers serious and problems of performance, such that my MagSafe LED would not illuminate when plugged on rare occasions, fan could turn unnecessarily, graphics performance were SUPER slow, and the health of my battery was running out quickly. I actually ran a report on the system at 2 different times and my quality of full load is depleting of 1.2% per charge cycle, which is very worrying. I went from 6281 mAh mAh 6138 maximum capacity after two cycles of load. I'm tracking closely it because at this rate, my battery will survive only at load cycles about 150 instead of the 1000 expected, gives me the idea that this could very well be a bad battery. The computer is also warm to the touch while you sleep, not connected to the power supply. I NAP active but even taking into account should not be hotter my iPhone did the same thing.

  I have reset the SMC, and it solved a couple of problems. The charger works fine now and my performance improved considerably (which made me feel better, either it is a high-performance laptop, a 11-inch MacBook Air should not he surpass), and battery life has improved. I feel even if it uses a lot of power in his sleep. Maybe I need to turn off the NAP and see if that makes a difference. The graphic bug still persists however, and I don't have enough time to see if the max battery is depleting again.

  In regards to the bug, is there something that can be done? Basically, I want to assure you that I took all appropriate measures or if someone else has this problem to see if it can be software related instead of my computer.

  I have the entry level MacBook Pro with the retina, last generation.

  Any constructive contribution welcome!

  See you soon.

  -adreaux

  Hello bernardn753,

  After reviewing your post, it seems that you are having problems with the screen showing strange things on it. Looks like you already have a troubleshooting. I recommend you read this article, as reset NVRAM would be to reset your screen resolution settings that should help.

  How to reset the NVRAM on your Mac.

  Thank you for using communities of Apple Support. Good day.

• with IOS 10.0.2 - 5s iphone Bluetooth problems

  Since upgrading ISO 10.0.2 my M50 from PLT Plantronics (helmet unique headset) do not reliably connects with my iPhone 5 more. I have to go to the settings, activate bluetooth turned off/turned on, touch the device on the bluetooth page, etc. Once it connects successfully, it will reconnect (if I turn off the headset and turn it back on) for a short period. The next day he does not connect itself but I play with bluetooth on the iPhone again.

  It has always worked perfectly before the 10th of IOS.

  And, as I noticed others mentioning, the volume is much lower with IOS 10. The maximum volume is much lower. I can barely hear it now, more normal background noise, while driving.

  I did:

  Forget this device for the PLT M50 and paired again (several times)

  I did a Reset Network Settings

  I don't know what else to do - but it's a 10.0.2 IOS issue.

  Hello AppleUser2k,

  Please ask questions about your problems of connection between your iPhone and your Plantronics headset since you upgraded to iOS 10. I understand how important it is to have your Bluetooth devices connect with your iPhone with reliability. Here's what I recommend.

  The first thing we want to make sure is that all your data is safe. You can perform a backup in iCloud or iTunes using this article: backing up your iPhone, iPad, and iPod touch.

  Once your data is safe, try the troubleshooting steps in this article to help: get help to connect a Bluetooth accessory with your iPhone, iPad or iPod touch device should also check with the manufacturer that the device has all the drivers and firmware to work with the new version of iOS.

  If you have checked everything and that you have installed the latest firmware or driver and always are problems, please be aware of your surroundings when you encounter these problems. If you can isolate the time or location, you see the problems, you can isolate the cause. You can even see this help article to ensure that you are not affected by outside interference: the potential sources of Wi-Fi and Bluetooth.

  Thanks again and have a great rest of your day.

• Problem after update 10.0.2 iOS iPhone touchscreen

  After I have updated to iOS 10.0.2, I noticed a problem with the touch screen. Using the position of the image on the right side, near the corner, the toushscreen does not work.
  For example: when you use the keyboard, I can't type the letter 'P', have trouble typing BACKSPACE. Using the Contacts app, I can't scroll through using the alphabet bar.

  Do what idea of the problem?

  Kind regards!

  Hi fabriciorela,

  Thanks for the upgrade to iOS 10! I understand that the right of your screen is unresponsive to the touch. You can try the steps in this link to fix the problem. If the screen of your iPhone, iPad or iPod touch does not respond to touch

  If it does not help the problem, try to restore the device to factory settings. I would like to backup your important data first.

  The backup of your iPhone, iPad and iPod touch

  Use iTunes on your Mac or PC to restore your iPhone, iPad or iPod to factory settings

  Please use the Apple Support communities to post your question. Let us know how it turns out. Have a great day.

• Bluetooth connection problem iPhone - audio system Nissan after upgrade iOS10

  After iOS10.0.2 iOS9 on iPhone upgrade, I got a cordially problem receive calls raise Nissan car audio.

  I can make a call without any problem. Bluetooth connection is stable. I can download address book e.t.c. But I can't receive a call. I see the incoming call on the radio shows. After pressing the button "answer" on the car Audio System, audio between iPhone and Audio streams car breaks down.

  But the cellular connection remains active. I need to rotate the audio output on the screen of the iPhone car for iPhone and back to the car. After that, I can continue my call via the car radio.

  Thanks in advance

  Hello StasV,

  Thank you for using communities Support from Apple. I know having a problem with calls on your iPhone in your car, it's not what you expect. The good news is that these steps will be useful for your problem of phone calls while using the bluetooth in your car. Go to settings > general > accessibility > routing of Audio calls and the value headset/Bluetooth Headset and retest your question.

  Audio routing call - the iPhone user Guide
  Help to connect your iPhone, iPad or iPod touch with your car radio

  See you soon!

• 2 iphones on one iTunes, problem of photo icloud account

  OK, my brother-in-law just updated its OS on his Iphone. He shared an Apple ID with his wife, who has his own iPhone. They all have two backup only in iCloud. His problem is that his wife photos are now on his phone. How can he fix it?

  Get its own identifier Apple- create and start using a Apple - Apple Support ID

• Problem activation ISO 10 September 2016

  After my Ipad iOS 10.0.2 update I could not activate because it says I am not access with the original Apple journal. Makes no sense. I bought the new Ipad in seven of 2013 Dabs.com. She has been linked to my Apple account 10 days ago (I deleted my profile by own Apple support Web site suggestion as a way to fix my problem, the other restoration/upgrade to the Ipad with ITunes update). I contacted the support of Apple (I have two numbers in case Apple). Asked Apple support to provide a proof of purchase I made. Told me now the reception that I provided does not correspond to my Ipad, but Apple isn't going to help with all the details to help to regularize the situation. The Ipad is mine and well was linked to my account from the date of purchase in September of 2013 until I removed it at the suggestion of site specific help from Apple. I now do not have access to my ipad £460 for more than 10 days and have lost money and time talking to 4 different cooperatives of Apple, after 6 calls and none seem able to deal with a ridiculous situation. Alexandre Vitorino (Apple) seems to have the best handle on weird how this situation is. Please can someone fix this? A software update on an Ipad that I own shouldn't stop me using it and then force me to prove that I admit actually before I use it again! I'm a professional businessman who uses it for meetings of the Council. I have a receipt for my camera and get treated like a kind of criminal.

  My sincere sympathy for those who can't find their original receipt or forget their original log-in Ipad because Apple does not help, you and your Ipad will be also useless mine is currently!

  If you are in the same situation please confirm to this post. I can't be alone, if she feels like it!

  Post edited by: cibble10

  Lock activation occurs when the ID of original Apple blocking it does not match with your current Apple ID.

  Until you can bring a receipt valid from an Apple reseller or authorized, it's nothing you can do.

  BTW, the polling stations in this Apple-owned forums is prohibited. You can review the terms of use.

• Anyone know how to solve my problem? I can't import my photos from Iphone to computer. Sign says: Photos in the camera cannot be imported because the IPhone is locked with a password or read. My phone is unlocked. I've tried everything

  Anyone know how to solve my problem? I can't import my photos from Iphone to computer. Sign says: Photos in the camera cannot be imported because the IPhone is locked with a password or read. My phone is unlocked. I tried everything, every single idea. Without success! Any other idea?

  For example, you specify that the device does not display the lock screen, correct? Do you use Touch IDS? If so, try to put your finger on the device to see if it's what he wants.

  See you soon,.

  GB