Problem with P10-873 SD Slot

Similar Questions

• Satellite P10 problems with Mat * a DVD ROM

  Hello

  I have a problem with my P10,
  I bought it for 2 months and 4 months ago my
  Carpet * a DVD ROM does strange things.
  When I try to copy a CD for example, it reads the cd source, after I put in those recordable, it starts to burn and suddenly it stops, says ERROR (Event Viewer: error on Controller\Dev01\CD-ROM) and my Combo drive is presented as a 'simple' DVD - RAM on Solution Explorer drive.

  Sometimes it won't read movies on DVD or CD so I have
  to restart the P10 and generally it can read the disks after that.
  So is my faulty drive, the card mother or just me?
  Have been looking for a new driver, but there is just a
  DVD-RAM, no driver for the drive itself.

  Hello

  Maybe the contact of the cable to the controller and CD player is loose. The error message said you it should be good!

  Your P10 is under warranty so bring a call Toshiba and it need to be repaired or a Service partner!

  Hans Bye

• Problem with PCI-e slots on the S51200ZCTO Pavilion

  Hello.  I bought this computer for use as a media server, replacing a 3300Z failed two weeks ago.  One of its functions is my AV receiver Rs232 command  I bought an adapter cheap PCI-e series online and installed.  The machine refused to start with the card installed in one of the three locations.  Attached to the HP splash screen.  Decided that my card 12 was obvious junk, I went downtown and bought another card for $30.  Same question.

  What I did:

  Disabled all 3 PCIe x 1 slots and slot of the minimap.

  The machine will start with the card installed, but of course, it's kind of useless.

  I activated the slots selectively.

  The machine will fail to start whenever the first location is enabled and one of the two cards is installled.

  If the first location is disabled, I can activate only two and three slots and the machine starts correctly with each installed card.

  I installed each card in turn in slot 2 and enabled only the slot 2 in the bios.

  Windows 7 can not find two cards.

  I manually installed each card in turn.

  They have installed but shows an error code 10 (device cannot be started)

  I have about confcluded that there must be a motherboard problem.

  I am a very technical user.  I have been upgraded and now my own machines for about 25 years and I've never met this kind of problem with a simple installation device PnP.

  If anyone has any idea I will try it.  I'm not enjoying the thought of working my way through levels of support for HP to convince them that there is a real problem or to ship the computer for repairs.

  Thanks for the chipset, here is another card:

  http://www.Newegg.com/product/product.aspx?item=N82E16815124112

• Strange problem with LAN on Satellite P10 connection

  Since yesterday I get really annoying balloon popup (it appears at intervals a decade or less seconds:(qui dit: câble débranché, mais le réseau fonctionne très bien (avec quelques retards quand il montre)))
  I wonder is this a hardware in my laptop problem or a problem with the internet provider. I have Realtek RTL8139/810 x LAN card. I checked another cable and of the ToolTip always shows :(
  Help, please

  Post edited by: motomadness

  Hello Adam

  On this path, it is not easy to say anything. I recommend you test somewhere else to make sure if this problem occurs due to material.

• Problems with slot-shaped table and set the values of column

  Hello
  
  I have a problem with a tabular presentation.
  
  I have two tables
  
  P_detail and table v_master
  
  columns of v_master:
  v_id
  v_Name
  v_info
  
  columns of p_detail:
  P_ID
  p_master_fk
  p_name
  p_info
  
  I want to have a tabular presentation where I can store permanent data retail values. That's why I want to keep the default main column join the detail columns.
  In SQL, I can do this with an outer join:
  
  SELECT m.v_name, d.p_master_fk, d.p_name, d.p_info
  OF v_master, p_detail
  WHERE v_id = p_master_fk (+)
  
  I get the lines that exist for the master data and can add values for the columns of detail. I removed the "add lines" because that makes no sense, because the amount lines are already offered at the opening of the tabular presentation.
  
  Now, I want to get/save the v_id (main table) in the p_master_fk column value
  
  How can I do this?
  
  Thank you and best regards,
  Matthias

  Hello

  One approach is to use a database instead trigger. If you define a database view using the query:

  SELECT m.v_id, m.v_name, d.p_id, d.p_master_fk, d.p_name, d.p_info
  OF v_master m, p_detail d
  WHERE v_id = p_master_fk (+)

  Then, create a trigger on the view that will insert in the detail table if d.p_id is null and update the secondary table if d.p_id is not null instead.

  The Apex tabular form is then based on the view (with identifiers like hidden columns) and all treatments multirow Apex should work without modification.

  Rod West

• Satellite P10-873 - no sound after reinstalling windows device

  Satellite P10 873 PSP 16th:-not his Device
  Win XP-Home Edition SP2

  Everything was going well until a bad sector on the hard drive. I have Ran Chkdsk /r and re-installed windows.

  In Control Panel/System/Hardware/Device Manager it is a unknown device in the sound,.
  Section of video and games controllers which I think can be unit XT of SRS truesurround.
  also Realtek AC97 sound devices shown as correct and functional.

  Tried to load the audio drivers from the website of Toshiba (sound-s-p10-xp-510005490) and still no audio device

  available from the configuration/sounds and Audio devices Control Panel.
  Got the patch KB888111 from Microsoft and installed, still no luck.

  Any ideas as to what I'm doing wrong please?

  Satellite P10 is old enough laptop model. I have very good experiences with P20. It's almost the same laptop, but a bit bigger. A friend of mine uses P10 for the job and we have installed WXP Pro using all the tricks of the Toshiba support page. The OS is installed two years ago, and the sound still works.

  If you can not get this to work, I recommend you remove all the important data for the D partition or save on an external device and make the clean OS install. It will be interesting to see if the problem persists.

  By the way: is a connected to your laptop satellite external game controller?
  An interesting solution, I found here.

• Satellite P10 873 LAN wireless connection

  Hi all

  I have a laptop Satellite P10 873. I just bought a Netgear DG834GT wireless modem/router and can not get completely connected to the internet via Tiscali (ISP).
  The problem manifests itself in what I can connect to the router and can even ping various sites on the net. But trying to connect to a site using MSIE I just get "unable to connect" rejection page
  In addition, using the CMD prompt, tempting a Telnet session to a web site on port 80 is rejected for example "80 www.bt.com.
  I put all the securities to a minimum without effect.
  I have another laptop that connects and works perfectly with the Netgear/Ticali Installer. I also identically configured MSIE on both machines without success.

  Anyone has any ideas what could be the cause?

  Thanks Mike

  [Edited by: admin October 14 05 11:49]

  Hello

  Well, do you have Devil WLan configurations?
  If you use the Windows settings you must activate it in the WLAN properties and if you are using a customer this option should be disabled.
  Also, check if the windows firewall is disabled. This option please the good state of market for the wireless card
  Sorry, I put t have other ideas.

  Good bye

• Satellite P10 873: power supply and CPU Overload

  I have the laptop of P10 - 873 for 4 months.
  The problem is that it turns off when it is connected to an electrical outlet.
  I can only work using the battery. When the battery goes out I normally load (with the laptop turned off) and then I use the notebook only with the battery again.
  If I connect it to AC power turns off after 3 minutes!

  I checked the CPU usage when connected to the AC and it seems that the CPU is too important (from 65 to 98% - where it stops!) without running applications other than the process required for the laptop to operate.

  I sent the laptop to TOSHIBA and they returned saying that they have updated the BIOS.
  Unfortunately, the problem was not fixed!

  Do you have any suggestions?

  Hello christina123.

  Sylvain is right. It is not a problem with the bios.
  I think it's a problem with the motherboard.

  Good bye

• Problems with Compaq Presario 5BW220 RAM

  This office is 8 years old and supposedly supports 512 MB memory SDRAM PC100.

  Recently, I worked on this for my son-in-law.  It came with 64 MB of SDRAM PC100 and Windows Millennium Edition.  I tried to install 2-256 MB memory SDRAM PC133 maximum amount supported RAM, but it refused to start.  I replaced every 256 MB module with a 128 MB PC100 module and managed to do start.  I expected to read 384, but he will read only 256 MB.  I had not all PC100 256 MB modules to use.  I finally installed modules from 2 to 128 MB PC100 and he left like that.

  I never had a problem in the past with an old desk accepting a combination of PC100 and PC133 modules, so it was a first for me.

  The Compaq Presario 5BW220 have a problem with the acceptance of this combination, and she actually says a maximum of 512 MB?

  This could be useful in the future:

  http://www.crucial.com/

  If you click "scan my system" he can tell you all sorts of things on the RAM.

  I have a system built home (with all the paperwork by moving the boxes...) who had a chip spoil.  I could not remember what RAM took it and I didn't go root through the boxes in the garage. =)

  Their scanning system could not see what kind of memory I had, but he told me exactly what my motherboard could support. (Type and max of 1 GB per slot)  He even suggested several configurations of memory.

  Once I saw what he said, he had, I remembered that I had bought before and it didn't fit.

• Satellite Pro L10 problem with Ports COM/Hyperterminal & Bluetooth

  Hello
  I have the following problems with the above machine:

  (1) I have attached an external series COM port to the machine. However, I can not connect to the COM Port using Hyperterminal.
  (2) I installed a Bluetooth USB adapter, but I can't view the protocol configuration.

  Each of the above works perfectly with another laptop that doesn't have a Bluetooth or even a network card.

  Everyone has experienced similar problems. I use WinXP SP2.

  Thank you

  MC

  Hello

  1, in which is the external COM port connected? Is detected in a straight path in Device Manager? What is the error msg to Hyperterminal?
  When connected via PCMCIA, try to change the settings for PCMCIA slot in the BIOS!

  2, try to reinstall the Toshiba Bluetooth stack! There may be some problems. The MS Bluetooth stack does not work properly with the Toshiba devices and one of the earlier Toshiba Bluetooth stack is not signed by Windows XP Service Pack 2!

  Hans Bye

• Problem with RAM Pro 4600 - Original RAM is not compatible!

  Hi, first sorry for my English.

  I ve had some problems with original module Toshiba PA3069U-M 256 MB of RAM for my Toshiba Satellite Pro 4600.

  History: (# = number of RAM)

  #1 was delivered to the original box from Toshiba and works in the slot A and B without any problem, but was damaged after only 2 weeks (!) --> Distributor sent me a new: #4

  #2 has been delieverd by the same distributor (same tine as #1), but only in the bag to shield static orginal. The laptop shows that the RAM is incompatible in the slot A and B--> I return

  #3 was delivered by another distributor, a few days after #1 was also damaged in the original Toshiba box. It still works fine in both slots.

  #4 was delivered yesterday, but only in the original static shield bag. The laptop shows that RAM is not compatible in both slots.

  The RAM in the box and the RAM that in static shield bag are two RAM Toshiba original from the manufacturing, seems to be quite the same. But still those in the area of work others are incompatible even after a BIOS update.

  Someone had the sampe problem or can help me?

  THX Braumeister

  Hello

  This seems very strange! The PA3069U-M 256 MB Ram Modules must adapt and work! So it may be that no work modules were damaged by sending by mail just packed in Toshiba box modules that work!

  Goodbye, TOK

• Problem with Half Life 2 display driver

  Please can someone help me?
  I just installed the game (Half Life 2)
  whenever I play the game everything is fine until I have quit the game, my laptop fell down and restarts.
  the error report I send said that there is a problem with my display driver.
  before I start the game, I get a message that says that my display driver is outdated and that I could get in trouble, because my computer is a laptop, (Nvidia) do not carry the Toshiba drivers.
  I've been on the Toshiba site and they have no display driver newer than the one I use now.
  Please could someone suggest something I could try.
  and Toshiba will bring a driver updated in the near future? This really seems a pity that the game seems to work verywell accept for this problem that exists.
  My laptop is a Toshiba Satellite P10 with a Nvidia G-FORCE FX GO5200 card inside.
  Your M Lovett.

  I have the same card and I get the same message, however without crashing.

  you have installed all the updates/fixes you can to ACE this may solve the problem.

  What about drivers who are the cause of the accident, one of my friends had a lot of problems with regularize them and crashing and it was running the game on a custom platform so maybe it's not that the real fault.

  [Edited by: admin 30 May 05 07:13]

• Replace HDD on P10 - 873

  I was wondering, where is the HARD drive located on the P10 873 and how do I go abouts changing?

  Y at - it the intsructions to show you how to diassemble the laptop?

  Thanks in adavnce

  Hello

  The HARD drive is placed at the bottom of the unit.
  If you want to replace the HARD drive, you must remove the battery and the optical drive, and then follow these steps:

  1. remove the four black screws that anchor the shield with aluminum on the HARD drive and pull it out.
  2. gently pull on the HARD drive the front panel of the computer to disconnect the system board, then pull it out.
  3. remove the four silver screws that attach the HARD drive to the HARD disk case
  4. then remove the casing HARD drive HARD drive

  Be careful with the replacement

• Satellite P10 - 873 swtichs audio out

  Hello

  mine is a P10-873. The problem is sometimes audio output is diabling alone for which I need to turn it off and restart restore the audio out put. I don't know the cause of it... could u please help me!
  Thank you

  Hello

  If please try to de - and reinstall the audio driver.

  At the http://eu.computers.toshiba-europe.com, you will find an audio driver for your laptop in the driver download section!

  Good luck
  Good bye

• Problem with the Satellite Pro 2100 and new modules of RAM

  Hello

  I have a Toshiba Satellite Pro 2100 and I have a problem with the memory upgrade.
  My notebook of startup only if a plug-in module to a ddr, but if I insert the two modules IN CC led orange flashing start when I try to turn on the pc. The stop led not blinking unless I take out the battery and the dc adapter.
  Here is the code of the modules:
  KTT3614/256 (original)
  KVR266X64SC25/256
  256 MB pc2100 both.
  Starting the PC with any of them, as well as the modules are both compatible.

  Any ideas?
  (Sorry for my English but I'm Italian: D)

  Post edited by: DaK_TaLeS

  Hello

  the second location of memory perhaps is the problem.
  Try to start with a module in the second slot, first an empty slot.

  Good bye