Problems creating a NAT form an outside inside the network on the PIX
I need to create a NAT device for an address from the outside to the inside, I'm not able to create the static method for it.
I have an external host with a 10.x.x.x address who wants to translate the 172.x.x.x address inside, using the PIX with the static control, it does not.
The I am using the syntax is:
Public static 172.1.1.9 (exterior, Interior) 10.1.1.10 netmask 255.255.255.255
but the pix sends the following error message:
0 on the outside has a lower value of security within 100
I don't have another device between the host and the PIX and so I am limited to use the PIX for this purpose.
What can I do else?
Hello
This feature is called bidirectional NAT. It was introduced in the code of 6.2. The previous code doesn't have this feature, sorry! So, if it must be done on the PIX, then you must have the code of version 6.2. What you're trying is right, but its your code that doesn't allow you to do.
Here is the link that talks about when this feature was introduced.
http://www.Cisco.com/univercd/CC/TD/doc/product/iaabu/PIX/pix_sw/v_62/Relnotes/pixrn621.htm#1249308
I hope this helps! Thank you
Renault
Tags: Cisco Security
Similar Questions
-
How can do NAT on (internet) outside inside LAN servers using a public IP address?
How can do NAT on (internet) outside inside LAN servers using a public IP address?
Should I using the route?
Lets say that 99.3.81.66 is your public IP address and ISP is on INT G0/0
IP nat inside source list 1 interface GigabitEthernet0/0 overload
IP nat inside source static tcp 10.3.81.6 443 993.81.66 443 extensible
IP nat inside source static tcp 10.3.81.61 80 99.3.81.66 80 extensibleaccess-list 1 permit 10.3.81.0 0.0.0.255
Int G0/0
NAT outside IP
int g0/2
IP nat inside
-
I can't seem to get a search form web app to work within another page of detail web app. Anyone know if this is possible?
I can view a list of web app; and the search engine works on a standard page. but when I try to load it into another web application details page, I get an error: "page not found". In this case, regarless of whether if I put {module_searchresuts} on the same page as the form or if I redirect the results to a different page.
Does anyone have any suggestions?
Thank you, but I needed to get the search form and the results of the Web A app to show inside the detail for the Web App B model... Apparently is not possible. I finished by simply using an iFrame - inase anyone who crosses the same question
-
Creating user database form and by inserting the username, password to a table
Hi all
Help me anyone how to do the following tasks from10g.
Creating user forms data and inserting the name of user, password, and other data to a specific table.
ArifHello
I think the guy gave you automated statements that you do not get :) Try this simple...FORMS_DDL('CREATE USER YOU_USER_NAME IDENTIFIED BY YOUR_PASSWORD'); -- Replace the user and pass variables upon your requirement. FORMS_DDL('GRANT CONNECT, RESOURCE TO YOUR_USER_NAME'); -- Or any role you want to set...
-Clément
-
Problem of size and form of policy on the executable in Windows 7
Hello
my colleague has a problem with his application on a Windows 7 computer. It's an executable built with LabVIEW 2011 on a XP machine.
Please see the attached screenshots for the appearance of the same exe under Windows XP and Windows 7 (where the fonts are more grand/resized).
Do you have ideas about how to avoid this? One solution could be the use of screenshots of screen/bitmaps instead of text, but it is very uneasy about future changes.
Best regards
Manu
Hi, manual,.
This has been asked several times before:
You must include some keys over in the INI of the executable file. I usually use those:
FPFont = "Tahoma" 13
BDFont = "Tahoma" 13
appFont = "Tahoma" 13
dialogFont = "Tahoma" 13
systemFont = "Tahoma" 13Best regards!
-
NAT order of operation on the PIX firewall
Hi all.
Can someone refer me to a document that clearly explains the order of operations on a PIX w firewall NAT / code 6.3 (3) or 6.3 (5)?
The statements are first aveluated? Static Nat, static policy NAT, NAT/PAT dynamics and so forth, for outbound connections?
And for incoming connections? I know that xlate table is checked on the first place for incoming connections, but, assuming that there is no entry corresponds to an incoming packet... What is the medal in which NAT set out are avaluated?
TKS in advance.
Diego
Hello
Refers to these positions. These are the same though...
HTH
AK
-
I can't find the field 'upload file' when creating a web form
Hi, I can't find the field 'upload file' when creating a web form. This is the site I put for my client home | ServilogEX. And I attach a display of the form.
Am I missing something?
Thanks in advance,
Diego.
Hi Diego,.
Your site map is too low. I believe that you must 'webMarketing' plan or higher to support downloads of files in the web forms.
-
How to create a dynamic form with bind variable: figure &;: table_name
My application has two LOV, one to select a schema and the other to select a table in this schema. Then I have a button that goes to a report that displays data in this table.schema.
Now, I want to create a link to a form where I can edit the record based on the identifier of this table.schema, but it does not appear that I can create a dynamic form where I pass the schema.table_name and the rowid. Is this possible? Can someone tell how can I do this? The form builder only wants a fixed schema/table name.
Thanks in advance.
Stuart.Hi Stuart,
If you create your section in the section #BOXBODY # it will already have to be encapsulated in a form.
He will submit to the correct location.
If you call your field of multi line field names, they will be stored in them.
form field f01 is mapped to wwv_flow.g_f01
Concerning
Michael
-
recommendations for the use of files outside of the root of web documents
Hi all
I decided to give another go to Dreamweaver now that I have CS4, rather than "hand coding", it's been a while, and I'm just getting used to everything...
So the first site I created is a PHP/MySQL site and I have the installer. I have the files local/tests/remote view works fine, trotting along, now I want add files I normally outside the root of web documents, for example, if the web root is/website/htdocs / I like to put some files in/site/includes and include / require them as needed. The problem is that I can't decide how to view these files/folders by Dreamweaver.
My only choice to move the root of the document/site sets up a directory? How will this effect site preview and other features?
Thank you
It is one of the less satisfactory aspects of the management of site in Dreamweaver, and several developers, including myself, made pressure on the Dreamweaver team in recent years to improve it. Who knows? They could possibly take knowledge.
The only way to do at present is to create two site definitions, one nested inside the other. Set up the site definition normally based on specific folder as the root of your site. Then create a new site definition based on site. Dreamweaver will be nag you it can cause problems, but this doesn't actually block you to do. The only potential problem is with synchronization of the site.
The problem with the use of site as the only basis for the definition of your site is that Dreamweaver automatically puts things like connections, Scripts and other files in the root of the site. Thus, all things evil at the level of the site hierarchy. Frankly, all this is a bit of a pain. Development of the dynamic site has been added to Dreamweaver only in the version 6 (Dreamweaver MX), and nobody had really thought through the need to store files outside the root of the site.
-
Problems with NAT? Can't access internet from inside the network?
I was intrigued with this problem for a few days now. I'm stuck on what could be the issue. The problem is that I can ping my router, G0/0 and G0/1, to the internet. However, since the switch and my PC, I can not ping Internet. I'm sure that everything is configured correctly, but here is my setup for the switch and the router:
Router 1:
version 15.1
no service button
horodateurs service debug datetime msec
Log service timestamps datetime msec
encryption password service
!
hostname LAN_Router_1
!
boot-start-marker
boot-end-marker
!
!
enable secret 5 *.
!
No aaa new-model
!
no location network-clock-participate 3
!
dot11 syslog
no ip source route
!
IP cef
!
!
!
!
domain IP MyTestLab.com
8.8.8.8 IP name-server
IP-server names 8.8.4.4
No ipv6 cef
!
Authenticated MultiLink bundle-name Panel
!
!
!
!
!
voice-card 0
!
!
!
!
!
!
!
Crypto pki token removal timeout default 0
!
!
!
!
license udi pid CISCO3845-MB sn FOC105013BA
username * secret privilege 15 5 *.
!
redundancy
!
!
property intellectual ssh time 60
property intellectual ssh authentication-2 retries
property intellectual ssh event logging
property intellectual ssh version 2
!
!
!
!
!
!
!
!
interface Loopback0
192.168.254.1 IP 255.255.255.255
!
interface GigabitEthernet0/0
DHCP IP address
penetration of the IP stream
stream IP output
NAT outside IP
IP virtual-reassembly in
automatic duplex
automatic speed
media type rj45
!
interface GigabitEthernet0/1
the IP 192.168.0.1 255.255.255.248
penetration of the IP stream
stream IP output
IP nat inside
IP virtual-reassembly in
GLBP 100 ip 192.168.0.4
priority GLBP 100 115
GLBP 100 preempt
automatic duplex
automatic speed
media type rj45
!
ospf Router 5
router ID - 192.168.254.1
network 192.168.0.1 0.0.0.0 area 1
192.168.254.1 network 0.0.0.0 area 0
!
IP forward-Protocol ND
no ip address of the http server
no ip http secure server
!
!
IP nat inside source list 10 interface GigabitEthernet0/0 overload
IP route 0.0.0.0 0.0.0.0 dhcp
!
access-list 10 permit 192.168.94.32 0.0.0.15 connect
access-list 10 permit 192.168.17.0 connect 0.0.0.7
access-list 10 permit 192.168.52.0 connect 0.0.0.7
access-list 10 permit 192.168.0.0 0.0.0.7 connect
access-list 10 deny any newspaper
!
!
!
!
!
!
control plan
!
!
!
!profile MGCP default
!
!
!
!
!
connection of the banner ^ C
W A R N I N GTHIS IS A PRIVATE COMPUTER SYSTEM.
This computer system, including all related equipment, network devices
(specifically including Internet access), are provided only for
authorized used.All computer systems may be monitored for all lawful, including purpose
to ensure that their use is authorized, for management of the system, to
facilitate protection against unauthorized access, and to verify security
survival and operational security procedures.Monitoring includes active attacks by authorized personnel and their
entities to test or verify the security of the system. During the surveillance,.
information may be examined, recorded, copied and used for authorized
purposes.All information, including personal information, placed on or sent over
This system may be monitored. Uses of this system, authorized or
unauthorized, constitutes consent to monitoring of this system.Unauthorized use may subject you to criminal prosecution. Evidence of
any unauthorized use collected during monitoring may be used for
administrative, criminal or other adverse action. Use of this system
constitutes a consent to monitoring for these purposes.
^ C
!
Line con 0
Synchronous recording
local connection
line to 0
line vty 0
local connection
entry ssh transport
output transport ssh
line vty 1 4
opening of session
transport of entry all
!
Scheduler allocate 20000 1000
NTP 198.60.73.8 Server
NTP 13.85.70.43 Server
SaveRunConfig event manager applet
cron cron-event timer entry ' 0 0 * * ".
command action 1.0 cli 'enable '.
cli 2.0 action command "RAM".Router 2:
version 15.1
horodateurs service debug datetime msec
Log service timestamps datetime msec
encryption password service
!
hostname LAN_Router_2
!
boot-start-marker
boot-end-marker
!
!
! card order type necessary for slot 1
Monitor logging warnings
enable secret 5 *.
!
No aaa new-model
!
clock timezone CST - 5 0
!
dot11 syslog
IP source-route
!
IP cef
!
!
!
!
domain IP MyTestLab.com
8.8.8.8 IP name-server
IP-server names 8.8.4.4
No ipv6 cef
!
Authenticated MultiLink bundle-name Panel
!
!
!
!
type of parameter-card inspect global
Select a dropped packet newspapers
!
voice-card 0
!
!
!
!
!
!
!
Crypto pki token removal timeout default 0
!
!
!
!
license udi pid CISCO3845-MB sn FOC1411592J
username * secret 5 *.!
redundancy
!
!
property intellectual ssh time 60
property intellectual ssh authentication-2 retries
property intellectual ssh event logging
property intellectual ssh version 2
!
!
!
!
!
!
!
!
interface Loopback0
192.168.254.2 the IP 255.255.255.255
!
interface GigabitEthernet0/0
DHCP IP address
penetration of the IP stream
stream IP output
NAT outside IP
IP virtual-reassembly in
automatic duplex
automatic speed
media type rj45
!
interface GigabitEthernet0/1
IP 192.168.0.2 255.255.255.248
penetration of the IP stream
stream IP output
IP nat inside
IP virtual-reassembly in
GLBP 100 ip 192.168.0.4
priority GLBP 100 110
automatic duplex
automatic speed
media type rj45
!
ospf Router 5
router ID - 192.168.254.2
network 192.168.0.2 0.0.0.0 area 1
0.0.0.0 network 192.168.254.2 area 0
!
Default IP gateway 192.168.0.1
IP forward-Protocol ND
no ip address of the http server
no ip http secure server
!
!
IP nat inside source list 10 interface GigabitEthernet0/0 overload
IP route 0.0.0.0 0.0.0.0 dhcp
!
SSH extended IP access list
permit tcp host 192.168.52.2 any eq 22 log
permit tcp 192.168.10.0 0.0.0.255 any eq 22 log
permit tcp host 192.168.17.18 any eq 22 log
any eq 22 host tcp 192.168.0.1 newspaper permit
permit tcp host 192.168.0.2 any eq 22 log
permit tcp host 192.168.0.3 any eq 22 log
permit tcp host 192.168.0.5 any eq 22 log
denyip a session
!
access-list 10 permit 192.168.94.32 0.0.0.15 connect
access-list 10 permit 192.168.17.0 connect 0.0.0.7
access-list 10 permit 192.168.52.0 connect 0.0.0.7
access-list 10 permit 192.168.0.0 0.0.0.7 connect
access-list 10 deny any newspaper
!
!
!
!
!
!
control plan
!
!
!
!
profile MGCP default
!
!
!
!
!
connection of the banner ^ C
W A R N I N GTHIS IS A PRIVATE COMPUTER SYSTEM.
This computer system, including all related equipment, network devices
(specifically including Internet access), are provided only for
authorized used.All computer systems may be monitored for all lawful, including purpose
to ensure that their use is authorized, for management of the system, to
facilitate protection against unauthorized access, and to verify security
survival and operational security procedures.Monitoring includes active attacks by authorized personnel and their
entities to test or verify the security of the system. During the surveillance,.
information may be examined, recorded, copied and used for authorized
purposes.All information, including personal information, placed on or sent over
This system may be monitored. Uses of this system, authorized or
unauthorized, constitutes consent to monitoring of this system.Unauthorized use may subject you to criminal prosecution. Evidence of
any unauthorized use collected during monitoring may be used for
administrative, criminal or other adverse action. Use of this system
constitutes a consent to monitoring for these purposes.
^ C
!
Line con 0
session-timeout 360
exec-timeout 360 0
7 password *.
Synchronous recording
local connection
line to 0
opening of session
line vty 0 4
SSH access class in
Synchronous recording
local connection
entry ssh transport
output transport ssh
!
Scheduler allocate 20000 1000
NTP 198.60.73.8 Server
NTP 13.85.70.43 Server
SaveRunConfig event manager applet
cron cron-event timer entry ' 0 0 * * ".
command action 1.0 cli 'enable '.
cli 2.0 action command "RAM".Switch:
version 12.2
no service button
tcp KeepAlive-component snap-in service
a tcp-KeepAlive-quick service
horodateurs service debug uptime
Log service timestamps uptime
encryption password service
!
hostname LAN_Switch
!
boot-start-marker
boot-end-marker
!
!
username * secret privilege 15 5 *.
!
!
!
No aaa new-model
clock timezone CST - 6
1 supply ws-c3750-24ts switch
mtu 1500 routing system
IP routing
IP - domain name MyTestLab.com
8.8.8.8 IP name-server
IP-server names 8.8.4.4
!
!
!
!
!
!
!
!
!
spanning tree mode rapid pvst
spanning tree logging
spanning tree extend id-system
!
internal allocation policy of VLAN ascendant
!
property intellectual ssh time 60
property intellectual ssh authentication-2 retries
property intellectual ssh event logging
property intellectual ssh version 2
!
!
interface Loopback0
192.168.254.5 the IP 255.255.255.255
!
interface FastEthernet1/0/1
switchport access vlan 17
switchport mode access
spanning tree portfast
spanning tree enable bpduguard
!
interface FastEthernet1/0/2
switchport access vlan 10
switchport mode access
spanning tree portfast
spanning tree enable bpduguard
!
interface FastEthernet1/0/3
switchport access vlan 666
switchport mode access
Shutdown
spanning tree portfast
spanning tree enable bpduguard
!
interface FastEthernet1/0/4
switchport access vlan 666
switchport mode access
Shutdown
spanning tree portfast
spanning tree enable bpduguard
!
interface FastEthernet1/0/5
switchport access vlan 666
switchport mode access
Shutdown
spanning tree portfast
spanning tree enable bpduguard
!
interface FastEthernet1/0/6
switchport access vlan 666
switchport mode access
Shutdown
spanning tree portfast
spanning tree enable bpduguard
!
interface FastEthernet1/0/7
switchport access vlan 666
switchport mode access
Shutdown
spanning tree portfast
spanning tree enable bpduguard
!
interface FastEthernet1/0/8
switchport access vlan 666
switchport mode access
Shutdown
spanning tree portfast
spanning tree enable bpduguard
!
interface FastEthernet1/0/9
switchport access vlan 666
switchport mode access
Shutdown
spanning tree portfast
spanning tree enable bpduguard
!
interface FastEthernet1/0/10
switchport access vlan 666
switchport mode access
Shutdown
spanning tree portfast
spanning tree enable bpduguard
!
interface FastEthernet1/0/11
switchport access vlan 666
switchport mode access
Shutdown
spanning tree portfast
spanning tree enable bpduguard
!
interface FastEthernet1/0/12
switchport access vlan 666
switchport mode access
Shutdown
spanning tree portfast
spanning tree enable bpduguard
!
interface FastEthernet1/0/13
switchport access vlan 666
switchport mode access
Shutdown
spanning tree portfast
spanning tree enable bpduguard
!
interface FastEthernet1/0/14
switchport access vlan 666
switchport mode access
Shutdown
spanning tree portfast
spanning tree enable bpduguard
!
interface FastEthernet1/0/15
switchport access vlan 666
switchport mode access
Shutdown
spanning tree portfast
spanning tree enable bpduguard
!
interface FastEthernet1/0/16
switchport access vlan 666
switchport mode access
Shutdown
spanning tree portfast
spanning tree enable bpduguard
!
interface FastEthernet1/0/17
switchport access vlan 666
switchport mode access
Shutdown
spanning tree portfast
spanning tree enable bpduguard
!
interface FastEthernet1/0/18
switchport access vlan 666
switchport mode access
Shutdown
spanning tree portfast
spanning tree enable bpduguard
!
interface FastEthernet1/0/19
Description # PC #.
switchport access vlan 10
switchport mode access
spanning tree portfast
spanning tree enable bpduguard
!
interface FastEthernet1/0/20
Description # X_BOX #.
switchport access vlan 666
switchport mode access
Shutdown
spanning tree portfast
spanning tree enable bpduguard
!
interface FastEthernet1/0/21
switchport access vlan 94
switchport mode access
spanning tree portfast
spanning tree enable bpduguard
!
interface FastEthernet1/0/22
switchport access vlan 5
switchport mode access
!
interface FastEthernet1/0/23
switchport access vlan 5
switchport mode access
!
interface FastEthernet1/0/24
switchport access vlan 5
switchport mode access
!
GigabitEthernet1/0/1 interface
switchport access vlan 666
Shutdown
!
interface GigabitEthernet1/0/2
switchport access vlan 666
Shutdown
!
interface Vlan1
no ip address
Shutdown
!
interface Vlan5
IP 192.168.0.5 255.255.255.248
!
interface Vlan10
address 192.168.10.2 255.255.255.0
!
interface Vlan17
IP 192.168.17.17 255.255.255.248
!
interface Vlan52
IP 192.168.52.1 255.255.255.248
!
interface Vlan94
IP 192.168.94.33 255.255.255.240
!
ospf Router 5
router ID - 192.168.254.5
Log-adjacency-changes
network 192.168.0.5 0.0.0.0 area 1
network 192.168.10.2 0.0.0.0 area 2
network 192.168.17.17 0.0.0.0 area 2
network 192.168.52.1 0.0.0.0 area 2
network 192.168.94.33 0.0.0.0 area 2
0.0.0.0 network 192.168.254.5 area 0
!
IP classless
IP route 0.0.0.0 0.0.0.0 192.168.0.4 permanent
no ip address of the http server
no ip http secure server
!
!
SSH_IN extended IP access list
permit tcp host 192.168.52.2 any eq 22 log
permit tcp 192.168.10.0 0.0.0.255 any eq 22 log
permit tcp host 192.168.17.18 any eq 22 log
any eq 22 host tcp 192.168.0.1 newspaper permit
permit tcp host 192.168.0.2 any eq 22 log
permit tcp host 192.168.0.3 any eq 22 log
permit tcp host 192.168.0.5 any eq 22 log
deny ip any any newspaper
!
!
connection of the banner ^ C
W A R N I N G
THIS IS A PRIVATE COMPUTER SYSTEM.
This computer system, including all related equipment, network devices
(specifically including Internet access), are provided only for
authorized used.
All computer systems may be monitored for all lawful, including purpose
to ensure that their use is authorized, for management of the system, to
facilitate protection against unauthorized access, and to verify security
survival and operational security procedures.
Monitoring includes active attacks by authorized personnel and their
entities to test or verify the security of the system. During the surveillance,.
information may be examined, recorded, copied and used for authorized
purposes.
All information, including personal information, placed on or sent over
This system may be monitored. Uses of this system, authorized or
unauthorized, constitutes consent to monitoring of this system.
Unauthorized use may subject you to criminal prosecution. Evidence of
any unauthorized use collected during monitoring may be used for
administrative, criminal or other adverse action. Use of this system
constitutes a consent to monitoring for these purposes.
^ C
!
Line con 0
session-timeout 60
exec-timeout 60 0
Synchronous recording
local connection
line vty 0
access-class SSH_IN in
local connection
line vty 1 4
access-class SSH_IN in
opening of session
line vty 5 15
access-class SSH_IN in
opening of session
!
NTP 198.60.73.8 Server
Event Manager environment suspend_ports_config flash: / susp_ports.dat
Event Manager environment suspend_ports_days 7
Event Manager user Directorystrategie "flash: / policies /.
Event manager session cli username "stw".
political event manager sl_suspend_ports.tcl
political event manager tm_suspend_ports.tcl
SaveRunConfig event manager applet
cron cron-event timer entry ' 0 0 * * ".
command action 1.0 cli 'enable '.
cli 2.0 action command "RAM".Well, I totally forgot the keyword "log" and NAT:
Cisco IOS NAT support ACLs with a keyword "log"?
A. When you configure Cisco IOS NAT translation dynamic NAT, an ACL is used to identify the packages that can be translated. The current NAT architecture does not support the ACL with a keyword "log".
http://www.Cisco.com/c/en/us/support/docs/IP/network-address-translation...
If your problem is not the mask with joker, but the command "log"...
-
Problem opening of HTML forms "Find Service request" and "Create Service Request"
Hello
I'm working on the establishment of a date for the Service of the EBS, and I'm unable to open forms HTML 'Find Service request' and "create Service request".
I get the error message:
Oracle error - 20001: ORA-20001: APP-FND-02902: option profile Multi-Org is required. Please define either MO: MO or Security Profile: profile of operating unit option. has been detected in MO_GLOBAL_INIT.
I have knowledge of EBS min set up and configuration. We simply use EBS as a source system for our ETLs. Please suggest no work around to solve the problem.
Thank you
Kishore
Go to the responsibility of the system administrator > profile > system. Search for the profile MO: unit operating and under field of responsibility, put in the name of responsibility you use to create the service request, click OK, and enter the value you want in the next window operating unit. He shoots to the top of all the defined business units and you can choose the one desired.
Thank you
Shree
-
Reader Adobe XI updates last week. Reinstalled this morning. All previous saved pdf files are now forms of words asking the conversion? Creates problems for my business. Help, please?
See http://windows.microsoft.com/en-us/windows/change-file-open-program#1TC=windows-7
Another method: http://windows.microsoft.com/en-us/windows/change-default-programs#1TC=windows-7
-
Link inside the declaration of nat in outermost interface ERROR
Hi all
I'm having a problem with my PIX501 w / "Cisco PIX Firewall Version 6.3 (4)", when ordering I get this caveat, is that normal? because it works perfectly fine in version 7.2 (2)...
THE ERROR:
PIX1 (config) # nat (outside) 1 222.127.244.52 255.255.255.252
WARNING: Link inside the nat in outermost interface declaration.
WARNING: Keyword 'outside' is probably missing.
REFERENCE:
# Sh nameif PIX1
ethernet0 nameif outside security0
nameif ethernet1 inside the security100
In addition,
Here is information on the 'outside' of the order PIX 6.3 setting
outdoors
If this interface is on a lower security interface that you identify by the corresponding overall statement, you must enter on the outside. This feature is called outside NAT or bidirectional NAT.
Note from firewall PIX 6.3.2 source translation is performed before the translation of destination. For this reason, if the political source NAT allows the connection, the xlate will create, even if the traffic is denied by the policy of destination.
Source:
http://www.Cisco.com/en/us/docs/security/PIX/pix63/command/reference/Mr.html#wp1032129
Don't forget to mark the answer as the correct answer or useful rate answers
-Jouni
-
ASA problem inside the VPN client routing
Hello
I have a problem where I can't reach the VPN clients with their vpn IP pool from the inside or the asa itself. Connect VPN clients can access internal network very well. I have no nat configured for the pool of vpn and packet trace crypt packages and puts it into the tunnel. I'm not sure what's wrong.
Here are a few relevant config:
network object obj - 192.168.245.0
192.168.245.0 subnet 255.255.255.0
192.168.245.1 - 192.168.245.50 vpn IP local pool
NAT (inside, outside) static source any any destination static obj - 192.168.245.0 obj - 192.168.245.0 no-proxy-arp-search to itinerary
Out of Packet trace:
Firewall # entry packet - trace inside the x.x.x.x icmp 8 0 192.168.245.33
Phase: 1
Type: ACCESS-LIST
Subtype:
Result: ALLOW
Config:
Implicit rule
Additional information:
MAC access list
Phase: 2
Type:-ROUTE SEARCH
Subtype: entry
Result: ALLOW
Config:
Additional information:
in 192.168.245.33 255.255.255.255 outside
Phase: 3
Type: ACCESS-LIST
Subtype: Journal
Result: ALLOW
Config:
Access-group acl-Interior interface inside
access list acl-Interior extended icmp permitted an echo
Additional information:
Phase: 4
Type: IP-OPTIONS
Subtype:
Result: ALLOW
Config:
Additional information:
Phase: 5
Type: INSPECT
Subtype: np - inspect
Result: ALLOW
Config:
Additional information:
Phase: 6
Type:
Subtype:
Result: ALLOW
Config:
Additional information:
Phase: 7
Type: NAT
Subtype:
Result: ALLOW
Config:
NAT (inside, outside) static source any any destination static obj - 192.168.245.0
obj - 192.168.245.0 no-proxy-arp-search to itinerary
Additional information:
Definition of static 0/x.x.x.x-x.x.x.x/0
Phase: 8
Type: VPN
Subtype: encrypt
Result: ALLOW
Config:
Additional information:
Phase: 9
Type: CREATING STREAMS
Subtype:
Result: ALLOW
Config:
Additional information:
New workflow created with the 277723432 id, package sent to the next module
Result:
input interface: inside
entry status: to the top
entry-line-status: to the top
output interface: outside
the status of the output: to the top
output-line-status: to the top
Action: allow
There is no route to the address pool of vpn. Maybe that's the problem? I don't know than that used to work before we went to 8.4.
Check if the firewall is enabled on your host from the client ravpn and blocking your pings.
-
Not able to ping inside the interface from outside
Hello
I'm trying to stimulate a new network like the diagram of the topology below:
However, I have a problem:
ASA:
I can ping to:
192.168.200.1 (Site_RTR IP, int fa0/1)
192.168.200.2 (ASA vlan interface IP, outside interface)
10.133.95.12 (DC_RTR, int fa0/1)
10.133.200.1 (ASA vlan interface IP, inside the interface)
10.133.200.23 (machine)
The RTR website, I can do a ping to:
10.133.95.12
192.168.200.1
192.168.200.2
10.133.200.23 (machine)
but not
10.133.200.1 (ASA vlan interface IP, inside the interface)
Question 1:
It is possible to access / ping back to this address within the IP Interface from outside?
Question 2:
As all subnets 10.0.0.0/8 will go through the interface on the outside, however for the internet traffic, out thru interfacera outside 2.
I haven't set up any nat, is correct to nat all out for outside2?
NAT (inside outside2) source Dynamics one interface
Thanks for the help.
JJ
Hi JJ,
If you plan doing a ping within the IP address of the interface, while the traffic is coming from any interface other than inside, you won't able to ping inside the IP address of the interface.
This is by design, and you cannot change it by any ACL or other settings.
Thank you
Ishan
Please do not forget to select a correct answer and rate useful posts
Maybe you are looking for
-
Win 7 Explorer missing column headers
Hello I noticed recently that my Win7 Explorer no longer displays the column headings. I know that Win7 now only display in 'details' but nothing there either. I tried to reset the folder options - no luck. I see when I googled the problem that other
-
negative film looking for the C5280?
Can I set up my HP C5280 to scan negatives somehow?
-
Original title: I have a BIG problem! When I start my computer I is no longer able to enter my tab start. It is empty. When I shoot computer (search) it says that I have nothing. All files have been deleted! A program called OnPay, Inc. (USA) check
-
Why am I required to accept the windows 10?
I'm furious, I have a very urgent work today that I have to get finished in the late afternoon, and I was wasting hours trying to delay installation (WHO I NEVER AGREED to) Windows 10. I am very stressed and will NEVER have anything to do with window
-
How to remove names from the address book in Windows Live Mail
I want to remove some names from my Windows Live Mail account but can't find a way to do it?