Problems of storage of the data in excel

Similar Questions

• There is a problem of storage with the data path [path to hard] store

  I have two sites connected by using a VPN connection over a WAN link. In each site, I have an esxi with several VMS host and operation of replication device of vSphere (v 5.1.1.0 Build 1079383) in each site. In each site, these is also a vCenter server with the device of RVS registered and logged with the other site. All the virtual machines are configured to replicate to the other site.

  In my initial configuration of the RV (first install) site remote had 2 vNIC used for the management and I figured it was my problem with replication (see kb2040302). So I have changed since my host configuration from the remote site to have that single vnic management (does not solve the problem). I then registered, removed and reinstalled the VR device without change to the problem.

  What is going on:

  1. I am able to configure replication between sites without a problem.

  2. first replication occurs between sites and reports a success.

  3. the remote VM replication to the main site continue to work properly and all is well for the days and continue to work.

  4. the main site of VM replication to the remote site fails on the second and all attempts to reproduce the error. There is a problem of storage with datastore path '[datastorename] '.

  

  I followed the advice of kb2040302 better as I can. But I must confess that I could use some of the more detailed instructions on how and what site should I check the logs. and how to check my configuration management vnic.

  I'm looking for someone provide additional troubleshooting steps with good detail.

  Thank you

  
  

  Resolution:

  The problem was caused by a security setting on the NFS Server data store. VRA could not delete the (hard).

  Specifically, my problem was with authorizations on the Synology NAS under the application of the "file Station.

• Hello. I so want to know if there is a way to keep the photos on icloud and get them deleted on your iphone, so that there is no problem of storage of the device

  Hello. I so want to know if there is a way to keep the photos on icloud and get them deleted on your iphone, so that there is no problem of storage of the device.

  iCloud is a synchronization system, not an external 'hard drive '. If you remove them on your device, they will remove icloud. To increase the available space, go settings/iCloud/Photos and select optimize iPhone/iPad storage. That will reduce the space required by 90% when it is fully effective.

• I tried to download a pdf and convert them into excel, but the data in excellent is always to the image format.  How can I get the pdf data into the columns and rows?

  I tried to download a pdf and convert them into excel, but the data in excellent is always to the image format.  How can I get the pdf data into the columns and rows so that I can do the calculations?

  If you start the https://forums.adobe.com/welcome Forums Index

  You will be able to select a forum for the specific Adobe products you use

  Click on the symbol "arrow down" on the right (where it is said to see all our products and Services) to open the drop-down list and scroll

• problem with the storage of the data in the table

  Hello

  I'm having the problem on the storage of data in the table. My problem is that whenever he makes a loop, the table just keep replacing them rather save to the next index. At 0, the value is 123, and 1 is 234. But I saw that all the data capture all crush to 0 until the last data see the 0. How can I fix this problem?

  
  

• Storage of the data in a table problem

  Hi guys,.
  
  I have the following schema:
  
  < xsd: element name = "Details" type = "DetailsType" / >
  < xsd: complexType name = "DetailsType" >
  < xsd: SEQUENCE >
  < xsd: element name = "count" type = "xsd: Integer" / >
  < xsd: element name = "loop" type = "xsd: Integer" / >
  < xsd: element name = "test" type = "xsd: Integer" / >
  < xsd: element name = "test2" type = "xsd: String" / >
  < xsd: element name = "test3" type = "xsd: String" / >
  < xsd: element name = "ReceiptArr" type = "xsd: String" maxOccurs = "unbounded" / >
  < / xsd: SEQUENCE >
  < / xsd: complexType >
  
  where I said ReceiptArr in a table.
  
  I try to copy the data in the table, but it does not work.
  
  I want the data to be like that
  
  ReceiptArr [1] = 12345
  ReceiptArr [2] = 23456
  ReceiptArr [3] = 78900
  .
  .
  .
  etc.
  
  
  Here is my statement copy of bpel
  
  
  < copy >
  < expression = "ora:getNodes ('receiveInput_Get_InputVariable', 'CashReceipt', concat ('/ ns2:CashReceipt / ns2:Detail [', bpws:getVariableData('DebtorVar','/ns9:Details/ns9:loop'),'. / ns2:receipt_number'))" / >
  < variable = "DebtorVar."
  Query = "Concat ('/ NS9:Details / NS9:ReceiptArr [', bpws:getVariableData('DebtorVar','/NS9:Details/NS9:loop'),']')" / >
  < / copy >
  
  and it fails, does anyone know how I can complete my table in bpel?
  
  Thank you
  K

  Hello
  I had to do in the past, and this is the approach I used. Create two variables, one for a number of records and the other as an index of the loop. The index of the loop the value 1 and get a number of nodes in the xml data in the entry for the second variable. Then the loop through the input xml data while the loop index is less than the record number, set the value of your table and incrementing the index of the loop, the use of brackets around the loop index (i.e. open close bpws:getVariableData('Variable_loopIndex') of the angle. I see that when I post this message, this part of the code is eating, and in my browser at least when I replace the ASCII for support, it is displayed instead of the media.

  There might be better ways to address the issue, but it worked for my process. I have not tested the below with your types to xml schema, but here's an example of how this can stand as a model using my code:

  
  
  
  
  
  
  
  
  
  

  
  condition = "bpws:getVariableData('Variable_loopIndex') < = bpws:getVariableData('Variable_recordCount')" > "
  
            
  
  
  Query = "/ ns2:CashReceipt / ns2:Detail / ns2:receipt_number [bpws:getVariableData('Variable_loopIndex')]" / > ""
  
  Query = "/ ns9:Details / ns9:ReceiptArr [bpws:getVariableData('Variable_loopIndex')]" / > ""
  
  
  
  
  
  
  
  
  
  

  Hope this helps
  Candace

  Published by: cmcavaney on June 25, 2009 08:26

• ESXi5 - problems with NFS and the data copy store

  Hello world

  I recently moved into a solution fully virtualized for my network, 3 x 5 ESXi servers running on our GigE network.

  First of all, I use all free software from VMware, so vCentre etc is out of the question.

  I have major problems when you try to copy files between:

  • NAS (NFS) to ESXi 5 host
  • ESXi host to the NAS (NFS) 5
  • And using VMware converter between ESXi 5 hosts converter Standalone

  The problem is that whenever I'm transfer between hosts I am struck with the horrible network performance. Even if I use GigE adapters and switches between my hosts I will receive no more than 12 Mbps speed of transfer real (100 Mbit/s connect?).

  On the flipside, if I use virtual guests on the same exact host I can happily transfer data between my NAS (NFS) servers with speeds between 60-150MBps ~ (1000 Mbps).

  Examples:

  Speed of 10 Mbps of transfer of ESXi_1 copy OF NFS data store share ~

  Server2008 (comments, located on ESXi_1) copy OF NFS 75MBps transfer rate ~.

  Server2011 SBS (comments, located on ESXi_2) copy OF Windows share 2008 (ESXi_1) transfer speed 120MBps. ~

  ESXi_2 copy OF NFS data store share transfer rate 5MBps ~.

  Attached (wtf.png) example:

  I copy a file that is located on our NFS share first, it's a 3 GB file to the copy within guest OS (2008), it is indicated in blue - top speed of 80MBps

  I copy the same exact NFS share for the host (datastore1), this is indicated in red - top speed of 7.5Mbps

  The third transfer/s (green) is between the customers of windows on different hosts, transfer a 6 GB file as well as a copy of the 360 MB file - transfers two happily send to GigE speeds with a peak around 40MBps

  I can reflect these results across the three servers without modification. Copies between you will be able to run well enough (not exactly 100% use of GigE) but at the moment where I try to do something to the data store it will just choke at all about a 100 Mbps connection speed.

  The final image (wot.png) confuses me beyond belief. I would try to explain what is happening here:

  • This image shows two times the same exact file transfers, except even machine PHYSICS
  • The first (red) transfer between the ESXi_2 host server and the NFS share using the browser data store and direct download - its top speed is around 8MBps
  • The second (green) transfer between a guest server 2008 running on ESXi_2, download the same file exactly at the exact location using vSphere Client. I mean the same EXACT file; It connects to the NFS drive by the data store ESXi_2 (NFS share).

  Why on earth can my comments directly download a file on a data store connected to NFS GigE clocked and yet the same exact host cannot go anywhere near corresponding to these speeds?

  As indicated in the title, the problem seems to happen whenever I use ESXi datastore browser on the host computer using vSphere Client or between browser datastore ESXi to/from an NFS share.

  No one knows what might happen?

  Is there some sort of restriction on the transfer of files between a host and shared NFS ESXi 5? Whence this bottleneck?

  Thanks in advance for all the help/ideas that guys can throw my way.

  P.S. Sorry for the wall of text, I really wanted to give as much information. as possible.

  What type of storage you have locally on the host computer?

  I have seen this problem with write-through controllers: http://wahlnetwork.com/2011/07/20/solving-slow-write-speeds-when-using-local-storage-on-a-vsphere-host/

• How to set the date output Excel in RTF format

  Hello
  
  I have a report and I have a date named as period column. And I need this field as this MAY-11 output.
  
  So I used this tag <? format-date: CREATION_DATE; "MON - YY'? > when I ran and see the results in rtf his works very well and the exit is on MAY 11, but when I see the result in Excel format its does not display correctly. It shows as 11-MAY '.
  
  Can someone tell me if this is a format problem or a problem with excel.
  
  Thanks and greetings
  Srikkanth

  You can add two spaces at the end to prevent excellent formatting, so that it treats the field as a text.

• storage of the data output of while loop

  Hello

  I have a data acquisition system set up to read the couple of a transducer. The output needs to be fed with an excel document, once the program stops running, or when a key is pressed.

  with the current code attached, the excel document is created, but it only shows the most recent series of data. How to make the table to store all the data coming from while loop?

  Ive only been programming with labview for two weeks, so chances are that it is something simple, but please help us in any case.

  JM

  To get what you expect, the Terminal output of table a while loop right click and select the option activate Indexing. Usually if you want to save data use queue to pass data inside the while loop to another loop/VI and perform data recording. For all that you have examples, please do a searc in LabVIEW help > find examples.

• want to compare the data in excel with real-time signal

  Hello

  my request is to check the PCB pins of I/o... Firstly I have signal corresponding to each pin in GOOD PCB board and the output of each needle is saved in excel using scripture to the spreadsheet... then the database be act as master for more tips of PCB...

  If I want to check the other pcb edge means that the same signals should be send on the pin of each Member of the PCB... received out of the Council should check with the data already stored in the database if this is the way to match status LED should illuminate otherwise is not to shine...

  pls help me finish this application... I have attached model vi with poster and Excel in too...

  I hate to say it, but you don't have really any type of application there.  It is quite difficult to help you complete when you barely started.  An express VI couple in a sequence structure do not apply.

  What you need to do is sit down and write a design specification.  What are your entries for this application? What are your results?  What do you think the UI to look like?  What steps do you need to do to go from A to B?  Chart out.

• Change the Date Format of the data in Excel

  Hello, my data is stored in an excel file. They are connected to the Warehouse Builder through ODBC.

  When I used an operator to change the format of a date column, I have an error which referred to ODBC.

  Someone know how I can change the date format of the data that are not initially stored in an oracle database in oracle,.

  but in an excel file.

  If you need to know anything else, please ask me. It is so important to me. Thank you.

  When you directly use the warehouse with MS Excel ODBC without the bridge builder, then send your question directly in the Warehouse Builder Forum:

  Warehouse Builder

  We are discussing only matters concerning Oracle gateways.

  Thank you

  Klaus

• local storage in the data store

  I have 4 ESXi 5.5 cluster nodes (host1, 2... 5) + 3par storage, I noticed that the local drive of host2 is detected as a data store.

  When I create a VM and I choose the data store, I can see all data related to my on3par LUN stores but it seems this drive local host2 too!

  I would like to remove it! Can you offer me please?

  You must hide hide this data store using permissions, you must run the following procedure: Open-> inventory-> warehouses vSphere-> select the select data-> permissions VMFS store-> click the user or group in the list and set them to 'No access' - are not propagated.

  Once achieve you its judgment showing everywhere.

• Total amount of storage in the data center

  I'm trying to get a script that will give me the whole total amount of space used in a data center. I want to launch against the center of data from virtual centres. There is a total of approximately 1900 of virtual machines and virtual machine is distributed among several LUNS. I need to get the overall figure for a migration.

  PS: I want to get the numbers in GB instead of megabytes and I also want it spits out a report in .csv on my local machine (c:\scripts\xxxx.csv)

  
  

  
  

  Thank you guys.

  I'm afraid that it won't work by changing just the data center-Get Get-cluster.

  The reason is the cmdlet Get-data store later in the script, on the location setting it only accepts the data center objects, folder and DatastoreCluster.

  But with a little small change, we can get it to work for clusters as well.

  Get-Cluster | Select Name,@{N="Storage Used (GB)";E={  $sum = Get-Datastore -RelatedObject (Get-VMHost -Location $_) |   where {$_.ExtensionData.Summary.MultipleHostAccess -and $_.Type -eq "VMFS"} |  Measure-Object -Property CapacityGB,FreeSpaceGB -Sum  [Math]::Round($sum[0].Sum - $sum[1].Sum,2)}} |Export-Csv c:\scrpits\xxxxx.csv -NoTypeInformation -UseCulture
  

• Cannot add the NFS storage to the data device

  Hello

  I try to add the NFS storage unit of data.

  I followed the documentation, and when I ran the script supposed to mount/add NFS storage to the device, an error message indicating that the export is read-only, which is actually not the case:

  ./Mount-NFS-Store.pl nfs--servername.domain.com:/hzn-data-01

  NFS: servername.domain.com:/hzn-data-01

  HOST: servername.domain.com

  servername.domain.com is alive.

  Mount.NFS: deadline set for Fri Mar 8 21:33:13 2013

  Mount.NFS: try the options based on the text 'hard, rsize = 32768, wsize = 32768, intr, addr = 128.178.102.59'

  Mount.NFS: prog 100003, try around = 3, prot = 6

  Mount.NFS: try the port TCP XXX.XXX.XXX.XXX prog 100003 3 prot 2049

  Mount.NFS: prog 100005, try around = 3, prot = 17

  Mount.NFS: try XXX.XXX.XXX.XXX prog 100005 3 UDP port 1234 prot

  ServerName.domain.com:/HZN-Data-01 on/opt/zimbra/store10 type nfs (rw, sync, noatime, hard, rsize is 32768, wsize = 32768, intr)

  Error has occurred: directory does not exist or is not writable: / opt/zimbra/store10

  zmvolume failed at ligne./mount-nfs-store.pl 49.

  Of course, I tried to go to the mount point (in this case/opt/zimbra/store10) and quite capable of writing in it (touch, create the file + dir, etc...).

  The data device has root access to the NFS export. I have no idea about the cause of this error.

  Any clue?

  Thank you very much

  Eric

  In my view, that ashish ask you to run the following command, so that the folder is owned by the user «zimbra»

  chown-r zimbra:zimbra

• Is it possible to export the data to excel without table?

  Is it possible to directly export data to excel from a view object?
  Currently I use af:tree to display data (this is a requirement). I have therefore no table in my page.
  I want to export lines of data corresponding to this tree to Excel.
  If I select export as tree id, then only the nodes are exported, in a single column. I would also like to other columns that are in its original Version.
  
  Someone help me please. I found ways to export of table, no VO.
  
  Thank you
  Jose

  Hello..
  I think that you can not directly from VO. In any case you can do it with rendered = false table, which will not show the table in page, but your condition is ok. (Drag and drop VOS as ADF Table to your page then he put false rendering)

  rendered = "false" >

  
  
  filename = "export_xls" title = "Export ADF faces" / >
  

  Hope it will be useful...