Problems WAG160Nv2 (find firmware, adres mac protection does not accept the multicast address)

Similar Questions

• Browser does not accept the IP address?

  I recently had to reset my wrt54g2 v1 router.  I'm currently trying to secure my network, but when I enter my IP address in my browser, it does not connect.  I tried to enter my IPv4, my default gateway, 192.168.1.1 and 192.168.0.1 and none of them works.  Help?

  Hello

  You wired or wireless connected to the router? Just to make sure, temporarily connect a cell phone to one of the ports numbered on the back of your router. Check your connection details (IPv4, DNS and default gateway address), then make sure that you receive these details with the automatic configuration (DHCP). With a stable powerlight, try to access the router configuration page using the default gateway.

• I tried to update OSX 10.5.6 to leopard 10.6.3 and was not working due to a disk error but now my mac book does not, as the starting system, but after a few secons it will turn off itself, what should I do? Thank you very much!

  I tried to update OSX 10.5.6 to leopard 10.6.3 and was not working due to a disk error but now my mac book does not, as the starting system, but after a few secons it will turn off itself, what should I do? Thank you very much!

  You probably should have updated to 10.5.8 first.

  Installation or update of Snow Leopard:

  http://manuals.info.Apple.com/en_US/Snow_Leopard_Installation_Instructions.PDF

• Connection problem diagnosis - "the remote device or resource does not accept the connection detected.

  My computer is a Windows Vista Home Premium 32-bit. The problem occurred about 2 months ago, while he was still in Vista, but please note that I've upgraded to Windows 7 last night and the problem is always the same.

  My Internet Explorer, updates to the computer, iTunes and everything, EXCEPT my AOL, does not work. My connection says 'excellent '. (Hang everything on my laptop to my wireless are works fine, that my office is having this problem)
  When I click on Internet Explorer, it says "Internet Explorer cannot display the webpage", and when I click on "analyze the connection problem" said "problems discovered - the remote device or resource does not accept the connection detected.
  I talked to my internet provider Comcast all morning this problem: she said that his side internet connections work properly. She walked through me steps including reconnected the router cords, control the way in which the Internet is put in place and other things, but everything was how it was supposed to be. She suggested that maybe AOL could be the problem and to remove it because I used it, so I did, but nothing has changed. So then she told me to contact Windows... (not sure how to call technical Windows supports without having to pay $59?, but found this forum)
  Is anyone familiar with this problem and could you please help or at least point me in the right direction?
  In addition, please let me know if you need any other information on the problem.
  Thank you
  Lily

  Hello

  Try the steps from the following link

  http://support.Microsoft.com/default.aspx/KB/956196

• I have a mac / downloaded adobe reader and does not accept the license agreement for end

  I have a mac / downloaded adobe reader and does not accept the license agreement for end.  It says successfully downloaded.  I'm going to use it and it won't work.  Told to close.  I opened adobe reader software and brings me back to install which I knocked again, and he says already installed.

  I closed out of all tabs, went to "safari" in the top of the page, clicked on close safari.  I clicked on Go, and then click applications, then I found adobe down and clicked on it.  then he gave me a place to click on accept.  I hope it works!

• Vista does not accept the password (password not changed or forgotten)

  Vista does not accept the password (we have not forgotten password of windows startup) how can we get around this problem .the password has not been changed or forgotten Vista has a little programming problem which stops the right password

  It is most often caused by the computer being infected, so after you go back into the system, it would be wise to make an analysis.

  http://www.elephantboycomputers.com/page2.html#Removing_Malware

  You can change your password to something you remember (or use a white) another administrative user account. If you had only an administrative user account, all is not lost. You can then follow the general recommendations for implementing user accounts in Vista that I will give you at the end of this post.

  All this requires a certain level of computer skills. You know better and that take the machine to a competent local computer tech (not a type of BigComputerStore/GeekSquad place) is the best solution for you.

  If you have an installation of Vista DVD (not a recovery DVDs), you can start the system with it. Select the default language, then select "repair your computer". Then select "Command Prompt". At the command prompt, type:

  NET user administrator / Active: Yes [press Enter]
  NET user [insert here the name of your user account] [insert the new password of user as 1234 here] [press Enter]

  [Note: do not enter the brackets!]

  Remove the installation DVD and restart the computer. Now, you will be able to connect to your user account by using the password that you set; for example, 1234.

  If you do not have a Vista installation DVD (only have a recovery disk), the computer mftr. may have given you the option to repair Vista (not a system recovery!) system in the diagnostic menu. This menu of diagnosis is the same one where you can choose Safe Mode. Get to this menu by repeatedly pressing the F8 key as the computer starts. If you do not have this option, you can make a bootable Vista file repair DVD in this link:

  http://NeoSmart.net/blog/2008/Windows-Vista-recovery-disc-download/

  Note: All the Neosmart recovery disk downloads are torrent files. There is a good explanation of the torrent on the site Web of Neosmart files. You will need a torrent as muTorrent client to get the files. Torrent client will download the .iso file with which to create the bootable DVD. You will need to use third-party burning software such as Nero, Roxio or the free ImgBurn (http://www.imgburn.com ) to burn the image .iso image file, not in the form of data.

  Once you have fixed things, log on to the additional administrative account you will be made by the suggestions below and disable the administrator account integrated yet for security reasons:

  Start Orb > Search box > type: cmd
  When cmd appears in the above results, right-click and choose "Run as Administrator" [OK]. Now, you will get the command prompt. At the command prompt, type:

  NET user administrator / active: No. [Enter]

  Exit the command prompt.

  General recommendations for creating users in Vista:

  You absolutely don't want to have only one user account. As XP and all the other modern operating systems, Vista is a multi-user system with integrated system of accounts as default Administrator and comments. These accounts should be left alone because they are part of the structure of the operating system.

  In particular, you do not want one account user with administrative privileges on Vista because the administrator account integrated (normally only used in emergencies) is disabled by default. If you use as an administrator for your daily work, and this account is corrupt, things will be difficult.  It is not impossible to activate the built-in administrator to rescue things, but there may be more that you want to do. Better not to put you in a bad situation at first.

  The user account that is for your daily work must be a Standard user, with the extra administrative user (call it something like 'CompAdmin' or 'Tech' or similar) only it for elevation purposes. As a user Standard is recommended for security reasons and will help protect your computer against infections. After you have created "CompAdmin", connect to it and change your normal user account Standard. Then log on to your regular account.

  If you want to go directly to the desktop and ignore the Welcome screen with the icons of the user accounts, you can do this:

  Start Orb > Search box > type: netplwiz [Enter]
  Click continue (or provide an administrator password) when you are prompted by UAC

  Uncheck "users must enter a user name and password to use this computer". Select a user account to connect automatically by clicking on the account you want to highlight and press OK. Enter the password for this user account (when it exists) when you are prompted. Leave blank if there is no password (null).
  MS - MVP - Elephant Boy computers - don't panic!

• The remote device or resource does not accept the connection

  I have a desktop computer Windows 7 connected to my router via an ethernet cable, but when I try to go to a website on Google Chrome as Google.ca, loading the page forever without even showing the page. Finally after a long wait, it finally says that the Web page is not available. I tried to go to the Web sites by using Internet Explorer, but occurs the same result. I tried to troubleshoot the problem and it "the remote device or resource does not accept the connection" is detected, but does not set automatically. I have a wireless printer connected to my router which is online and works very well. I can even connect to my router page. But still no access to Web pages don't like my outlook.com and etc. Sometimes a go open the network and sharing Center to change the settings of the card and disable the wired ethernet only to activate it again. It works only a few times, and it's really frustrating, because it is the only computer that does not connect to the internet, even with a ethernet cable. Please find a solution as soon as possible. Thank you.

  Hello Kyle,.

  Your computer is connected to a domain network?

  If your computer is connected to a domain network, then, I suggest you follow the link below to post your query in the TechNet forums, because they have more expertise on this issue.

  Forums TechNet for Windows 7
  http://social.technet.Microsoft.com/forums/Windows/en-us/home?Forum=w7itpronetworking

  Otherwise, try to follow the following suggestions to solve the problem.

  "Internet Explorer cannot display the webpage" error

  Note: Reset the Internet Explorer settings can reset security settings or privacy settings that you have added to the list of Trusted Sites. Reset the Internet Explorer settings can also reset parental control settings. We recommend that you note these sites before you use the reset Internet Explorer settings. Reset Internet Explorer is not reversible, and all the previous settings are lost after reset.

  Also refer to:

  The remote device or resource does not accept the connection

  I hope this helps. Otherwise, feel free to write us again and we will be happy to help you.

  Thank you

• IE9 "the remote device or resource does not accept the connection.

  IE9, "the remote device or resource does not accept the connection" appears when you try to open any website. My office to tell me that it is connected but cannot access any www. Meanwhile, my laptop connects fine. I have reset the settings in the internet options does not. I downloaded 'team' to connect (or similar) and asked for a connection and I thought that suspicious so uninstall this program... leaving me without access to the internet... * sigh * please can someone help me?

  Hello

  
  Method 1:
   
  Step 1:
   
  Run the network troubleshooter and see if that diagnoses the problem.
  Using the troubleshooter from network in Windows 7
  http://Windows.Microsoft.com/en-us/Windows7/using-the-network-troubleshooter-in-Windows-7
   
  Step 2:
   
  Reference:
   
  Windows wireless and wired network connection problems
  http://Windows.Microsoft.com/en-us/Windows/help/wired-and-wireless-network-connection-problems-in-Windows
   
  See also:
  How can I troubleshoot network card?
  http://Windows.Microsoft.com/en-us/Windows7/fix-network-adapter-problems
   
  Method 2:
   
  Temporarily disable antivirus programs and firewalls.

  Disable the anti-virus software

  
  http://Windows.Microsoft.com/en-us/Windows7/disable-antivirus-software

  Windows Firewall
  http://Windows.Microsoft.com/en-us/Windows7/products/features/Windows-Firewall

  http://Windows.Microsoft.com/en-us/Windows7/firewall-frequently-asked-questions

  Note: make sure that you enable the antivirus software, other security and firewall after the test programs.

  Warning:
  Antivirus software can help protect your computer against viruses and other security threats. In most cases, you should not disable your antivirus software. If you need to disable temporarily to install other software, you must reactivate as soon as you are finished. If you are connected to the Internet or a network, while your antivirus software is disabled, your computer is vulnerable to attacks.

   
  Display the results.

• Windows 8 does not accept the product key

  About 3 years ago I bought Windows 8 Pro (64-bit). In the meantime, I reinstalled the system a good several times because of some strange accidents (see my other question). Now, I tried to reinstall it again, until Windows 10 comes out, but activation does not accept the key. I read on other forums that this is probably beyond the limit of activations.

  Is there a way to reset the key or am I forced to buy a second?

  Thank you

  Mario

  Hello Mario,

  Thanks for posting your question on the Microsoft community.

  I would like to know some information about the problem so that we can help you better.

  1. you made any hardware or software changes to the Surface before the show?
  2. do you receive a code or a message when you say, 'activation does not accept the key?

  Thank you for details on the question and your efforts to resolve.

  This problem may occur because corrupt Windows activation files or parameters.

  I would suggest trying the following methods and check if it helps.

  Method 1:
  To activate the phone and check.
  Refer to this article:
  Get help from Microsoft Windows activation
  https://support.Microsoft.com/en-us/KB/950929

  If this does not help, use method 2.

  Method 2:
  Please refer to the suggestions of nobody611 responded on 4 December 2012 and check the issue.
  http://answers.Microsoft.com/en-us/Windows/Forum/windows_8-windows_install/Windows-8-activation-after-clean-install-does-not/01047349-516A-485f-b88d-68c1c9ac0e9c

  Note: Serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click on the number below to view the article in the Microsoft Knowledge Base:
  http://support.Microsoft.com/kb/322756

  I hope this information helps.

  Please let us know if you need more help.

  Thank you

• Error: This page cannot be displayed - the remote device and does not accept the connection. (! found)

  * Original title: this page cannot be display the remote or unit does not accept the connection. (! found)

  My internet connection works very well, I'm trying to access a page of my gate of the school we use to complete missions. I can access my web page of schools, I can access my e-mail from the school, but I can't get the e-portfolio page. It says cannot display this page - the remote device and does not accept the connection - (! found). He said to ensure that the TSL and SSL in the advanced internet options security part turned on who they are, my better protected as well the mode. I've never had a problem accessing this page before. It is only this page! Help!

  Hello Teresa,.

  The probable cause of this problem could be due to wrong settings for internet explore.

  Please see the link below, Windows 8, follow the steps to check the Proxy and DNS settings
  http://support.Microsoft.com/kb/956196/en-us

  Warning: Reset the Internet Explorer settings can reset security settings or privacy settings that you have added to the list of Trusted Sites. Reset the Internet Explorer settings can also reset parental control settings. We recommend that you note these sites before you use the reset Internet Explorer settings.

  Hope this helps, please answer with the results for assistance.

• IPhone does not accept the code to check for text messages

  II phone does not accept the code verification for the transfer of messages text imac

  Maybe these articles will help:

  Get a verification code and connect with authentication to two factors - Apple Support

  If you don't receive your check or reset email - Apple Support

  If this is not the case, can you explain a little more detail what exactly is your problem?  Or see the 'Contact us' at the bottom of the second article.

• When I open a link in a new window does not display the web address.

  When I open a link in a new window does not display the web address. What have I done wrong? It used to work and it works if I open the link in a new tab, the problem is that I hate to use tabs prefer a new window every time... Help!

  Start Firefox in Firefox to solve the issues in Safe Mode to check if one of the extensions or if hardware acceleration is the cause of the problem (switch to the DEFAULT theme: Firefox (Tools) > Add-ons > appearance/themes).

  • Makes no changes on the start safe mode window.
  • https://support.Mozilla.org/KB/safe+mode
  • https://support.Mozilla.org/KB/troubleshooting+extensions+and+themes

• Re: Failed on nine L510 Vista admin password - does not accept the admin pass

  Hi all

  Completely baffled by this one so would appreciate any advice.

  I just bought a new Satellite L510 with vista hard disk installation.

  I went through the installation process long and eventually got to the point where I could configure my admin account and the name of my computer.

  I chose the name of my admin account and typed in the password and confirm the password and named my computer.

  Now when I get to the initial Vista logon screen, it does not accept the password I am entered (and confirmed).

  This can be a problem with caps lock, as the password was all numbers.

  (the password was all numbers and five numbers)

  It, however, gives the correct indication for the password that I entered. It does not accept the password.

  I would be happy even just redo the installation process, but I have no idea how to do this, because I can't even a quick command-line anywhere.

  Help, please!

  It's strange. You can log on using a different user name?

  In any case to run recovery, you either:

  * Press and hold zero during the power upward
  * Press F8 before Windows starts to enter the Windows Start Menu, then run recovery of the option "repair your computer". http://APS2.toshiba-tro.de/KB0/HTD9102IR0000R01.htm

• update of sql server 2005 service pack 3 error code 6D9E Windows update security does not accept the update

  update of sql server 2005 service pack 3 error code 6D9E Windows update security does not accept the update

  Hey lasdj,

  Thanks for posting in the Microsoft answers site!

  If you receive Windows Update error 6d9e while installing SQL Server 2005 Service Pack 3 by using Windows Update, it means that the installation folders and directories are compressed or encrypted.

  To fix this problem, make sure the folder locations where you are installing the service pack to aren't compressed or encrypted, or specify a different folder and then run Windows Update again.

  Therefore, remove the compression of the DATA directory and run together to the top again.

  Remove compression from the C:\Program Files\Microsoft SQL Server folder and see if you are able to install the updates without any problem.

  See the links below for more details:
  
  Windows Update error 6d9e
  http://Windows.Microsoft.com/en-IE/Windows-Vista/Windows-Update-error-6D9E 

  Install SQL Server 2005 and 2008 failures (compressed DATA directory)
  http://blogs.msdn.com/psssql/archive/2009/02/24/SQL-Server-2005-and-2008-Setup-failures-compressed-data-directory.aspx

  I hope this helps!
  Gokul T - Microsoft Support

• My computer does not accept the print command.

  My computer does not accept the print command.  He always questions me to save a file, I don't want to save a file.  How can I change this?

  Sherimcfalls,

  1. what operating system is installed on the computer?
  2. the problem occurs with any particular application?

  Method 1
  I suggest you try the steps from the following link:

  Printer in Windows problems
  http://Windows.Microsoft.com/en-us/Windows/help/printer-problems-in-Windows

  Method 2
  Try to set the default printer.

  Change your default printer
  http://Windows.Microsoft.com/en-us/Windows7/change-your-default-printer
  http://Windows.Microsoft.com/en-us/Windows-Vista/change-your-default-printer