Problems with connecting fiber and new router AirPort

Similar Questions

• problem with thinkpad x220i and rangeplus router wrt 110

  Just got a new thinkpad x220i and whenever I try to connect to my wireless network, accidents of router and my cable modem seems to descend with her and the internet connection is also lost.

  I need to restart the whole nine yards.

  I got this router - rangeplus wireless wrt 110 for 3 years without problems with a mac, my ipad, iphone and my previous thinkpad x 201

  Someone has an idea of what could be the cause?

  very frustrating

  Thannks

  In the computer turn off IPv6 under properties for wired connections and wireless LAN.  Restart and try again.

• Problem with MAC pinning and new VLAN

  [Cross Announces nexus 1000V and forums of the UCS]

  Hi all, I have a working of the UCS 1.4 configuration (3i) and the Nexus 1000V 1.4 and according to best practices guide uses "channel-group auto on mac - pinning mode" on the uplink of Nexus. I have a problem when you add a new VLAN in this environment, and it is a reproducible problem in two different facilities.

  I pass by the VLAN usual creation process on the Nexus, the network upstream and within the UCS himself. I create new port vethernet profile and set it as an access port in the new VIRTUAL LAN. However when I join a VM (existing or new) to this new port vethernet profile in vCentre virtual machine cannot communicate with anything. However, if I disable MAC pinning with 'no channel-group auto on mac - pinning mode', the virtual machine will start instantly talk to the outside world and the new VIRTUAL LAN is running. Can I turn MAC pinning back once again, and everything continues to work.

  So the question is, is this normal or is there a problem? MAC the Θtiquetage has a brief interruption of the uplink, so is not a viable long-term customer solution when they want to add new VLAN. Is it possible to add new VLANS in this scenario without any unavailability of the network, but brief?

  Thank you

  Close the loop on this.  You tap the CSCto00715bug.

  Symptom: New MAC address is not learn on vem in the l2 table even though the mac address table is not overflow yet. vemcmd show l2-emergency-aging-stats | grep "Number of entries that could not be inserted:" will show extreme large number. Conditions: Nexus1000v VEM running on SV1.4 release. There are two CPU cores on the host. This issue may happen at race condition. Workaround: Reboot the ESX/ESXi host. 

  This problem is corrected in the 1. 4A release.

  Kind regards

  Robert

• [SOLVED] Problem with the ACB and InterVLAN routing

  Hello.

  I have Cisco 3750 G with IOS k9 - mz.150 - 2.SE4 Service of intellectual property. In my network, I have 4 VLANs with 4 internet gateways. I have set 4 static route for each gateways and with PBR to match this static routes. If I use "set ip next-hop" all traffic goes through the specific gateway interVlan routing does not work (I need to because the customers interVlan routing in different VLANS must be), and if I use 'set ip default next-hop', I was incapable of it attributed to Vlan (road-map lan14 not supported based on routing strategies).

  Model SDM is on the road that ip Routing is enabled.

  Here is my config for 2 of these VLANS:

  interface Vlan7
  IP 192.168.7.254 255.255.255.0
  IP access-group 107 to
  !
  interface Vlan14
  IP 192.168.14.254 255.255.255.0
  IP access-group 114 to
  !
  IP http server
  IP http secure server
  !
  !
  IP route 0.0.0.0 0.0.0.0 192.168.70.254
  IP route 0.0.0.0 0.0.0.0 192.168.140.254
  !
  access-list 107 permit udp any eq bootpc any eq bootps
  access-list 107 allow ip 192.168.7.0 0.0.0.255 any

  access-list 114 permit udp any eq bootpc any eq bootps
  access-list 114 allow ip 192.168.14.0 0.0.0.255 any

  lan7 allowed 10 route map
  corresponds to the IP 107
  IP 192.168.70.254 jump according to the value
  !

  lan14 allowed 10 route map
  corresponds to the IP 114
  IP 192.168.140.254 jump according to the value

  !

  Where is my error in config?

  Please help me, I'm stuck here almost three weeks.

  Hello

  You have created courses 2-card to set the next hop for a portion of the traffic classified with an acl.

  If you want any other traffic manager you must create an empty instance of your roadmap

  Example:

  lan7 allowed 10 route map

  football game...

  map of route allowed lan7 20 ==> Add this instance and leave it empty. You say the switch/router that he must refrain from other traffic but nothing to apply.

  Hope that this clear.

• Unable to connect to my new router cable, my XP and Windows 7 machines

  Vista, wireless router Netgear, no link, please help

  No matter what I try, I can't connect to my new router cable, my XP and Windows 7 machines work fine but the Vista laptop are it. Have searched the web, looked at this site and the forums, but nothing does not jump and helps me solve the problem. I use a HP Pavilion DV9000 laptop, all service packs updates and so forth... any ideas?

  I suggest that you contact your ISP and get their help in setting up the Vista machine so it connects properly.  They know the right settings for the access provider, while we do not have and that there may be something else you need to do with Vista which is different of the other two systems (and hopefullly the ISP will also know and be able to talk you through the process).  I call my ISP all the time and they are VERY useful and have ALWAYS resolved any problems, I called (even if sometimes he had a visit from a technician).

  If the ISP Can ' t/don't/can't help you, then after coming back here and we'll try to go through it step by step, even if we cannot have all the information we need.  But I am sure that they will be able to help you more quickly and more effectively and with greater chances of success.

  I hope this helps.

  Good luck!

  Lorien - MCSA/MCSE/network + / has + - if this post solves your problem, please click the 'Mark as answer' or 'Useful' button at the top of this message. Marking a post as answer, or relatively useful, you help others find the answer more quickly.

• I've had dramas with my photos because I got my new iphone 4s in saying that there is a problem with the properties and I can't change the format of images

  Hello

  I've had dramas with my photos because I got my new iphone 4s in saying that there is a problem with the properties and I can't change the format of images (ie the rotating EGTC)

  Now, I see the image preview and it disappears to the flower, so I did not see one of my photos

  Some would like TO help on this im so not good with this kind of thing.

  Appreciate it in advance

  Let

  Hello

  • When you change the format of images of?
  • What is Windows Explorer or Itunes?

  Try the TV activation

  Enabled and disable the Option 'show window previews (thumbnails) '.

  a. right click on the taskbar.

  b. Select Properties.

  c. check show window previews (thumbnails) "Option. .

• Satellite Pro C650D - problems with the audio and game controllers

  Hello

  I recently had problems with my microphone and speakers/headphones and game controllers.
  Sometimes the microphone stops working when on Skype, for example, but most of the time works fine, once again, when I restart the pc.

  Stakeholders sometimes still work when I connect headset.
  Some of the sounds are still coming through the speakers while some coming through the headphones.

  I have a usb game controller which also did not work everything properly.
  If I assign buttons in the program that they do not work in the game.

  All these devices are in Device Manager in a group that makes me think it's sort of annoying update doubtful that messes with them.

  Any body have similar problems or know what to do better?

  See you soon
  Laurin

  Hello

  Can you please send some details on the laptop model and the system you are using?

  With regard to the issue of sound/mic:
  > The microphone sometimes stops working when on Skype, for example, but most of the time works fine, once again, when I restart the pc.

  Are you talking about internal microphone or external? This only happens using Skype?
  In your case I would test the microphone using different applications to make sure that is not a Skype related issue.

  > Yet sometimes the speakers work when I connect headset.
  I recommend this thread:
  http://forums.computers.Toshiba-Europe.com/forums/thread.jspa?threadID=65295

  The user has had a similar problem, but this phenomenon was linked to the Realtek HD Audio Manager settings.
  She wrote:
  + In the upper right corner, there is a small yellow folder called "Connector settings" in my version. +
  + There, finally I could re-enable the setting "enable popup dialog box, when the unit is plugged. +

  + So now when I plug an external speaker or headphones, it appears, and I select the option "helmet" (instead of "line-in"), and then the sound only through the headphones/ext.speaker.+

  Regarding the game controller:
  > I have a usb game controller which also did not work everything properly.
  > If I attribute buttons in the program, they do not work in the game.
  I put t think its problem of laptop in my opinion, you must make sure that the controller is compatible with the games you play and also recommended to check some info provided by the manufacturer of the game controller.

• Problems with wifi, bluetooth and gps in my iphone after updating iOS 6

  After that the last iOS 9.3 update my iphone 6 has problems with wifi, bluetooth and gps. Now, my wifi connection is slower and falls easily on a short distance. My bluetooth does the same. But the biggest problem is the GPS on my phone. I tried Island:

  -By doing a reset network

  -Do a reset total and restore my phone

  -To restart my phone twice.

  -Audit and third-party applications unnistalling

  Nothing works. I was in the apple store where they checked my phone and they say everything is ok with the phone. I'm not crazy, and I know when something does not work correctly. Also, I think it's iOS 9.3 update a reaponsible for my phone issues.

  Please fix bugs fast.

  Having the same exact problems since the upgrade. In addition, battery drains very quickly now, and sometimes the phone becomes very hot. It took to the Genius Bar and they told me everything was normal in the diagnostic tests. Restored, restarting, etc., and always the same problems. GPS locates me, but then don't follow my movement at all and told to go outside as the gps is not detected even if I am outside. Bluetooth connection to the car and watch grave intermittently. Signal WiFi is greatly reduced and falls easily.

• Problems with Windows Update and load XP SP3

  I had a problem with my system and had to replace my HARD drive and reload XP and all my applications and data.  Now, I installed SP2 and try to install SP3. Windows Update does not work (get the 080244019 error code x) and when I try to install the SP3 files from the Microsoft site, it'll run about halfway through and then stop and hang, displaying the message "Finish Installation" with bar at halfway of the progression.  I tried the MSRT and FixIt nothing helps.  I checked services.msc to see all the required services are enabled or started.  I read that some malware will be stop some services without notice.

  After a few attempts to load the file SP3 failed, check Add/Remove programs in Control Panel Windows XP Service Pack lists 3 but no file size or to update the date information as with other programs.  My browser is IE8 and I was doing some Hot fix for Windows XP downloads, this adventure started about 3 weeks ago, but no other automatic update downloads.  I use the following McAfee provided by my ISP for protection AV and firewall with regular full scans.  Scan today revealed there is apparently a single trojan file that cannot be deleted, but there were no further details.  My system is also fully functional; I seem to get the updates for McAfee and other applications OK but not SP3.  I received or otherwise installed following updates or Hot Fix for XP downloads in the past 3 weeks:

  KB954550-v5

  KB932823-v3

  KB915800 v4

  KB884020

  KB926239

  KB2618444 (Windows IE8 security update)

  I found an answer on another forum on editing the registry for the "/ Edit EDWARD CSDVersion value ' but have not yet tried waiting for any response to this request.  I'd like some useful suggestions.  Thank you and happy new year!

  Thanks for the quick response.  I did some checking on my system, I have XP Home Edition ships with the system bought in July 2007.  Add/Remove Programs shows that the aborted install XP SP3 and IE8 installation; I tried to load the SP2 file but it doesn't show here as an addition, so it may have been part of the original XP CD and I just crush.  Even for IE7 so I am not able to drop back to all recommend you.  I will try your solution later today and post my results. I saved SP2, SP3 and IE8 in my office and a flash player to reload later according to your instructions.  Stay tuned.

  It would be unusual for a CD of Windows XP (official) to have integrated Internet Explorer 7.

• Problems with my mouse, and have not been able to find a solution to the research on various forums.

  Original title: mouse problems

  I have problems with my mouse and have not been able to find a solution to the research on various forums. Here are the symptoms:

  1. you must click several times to get the menus to open. Sometimes they are not just and sometimes they open with a single click flash but do not stick until I clicked several times.

  2 several times the menu drop down and seem to become transparent (not in looks) because when I click on something on the menu, he actually selects everything that is behind the menu drop down. For example, if I'm in powerpoint and you select an item in edit mode, it might work and here again he can just select the slideview behind the menu and expand. Or well, if I'm on a Web site, such as Facebook, and I chose to close the session, rather than enable the disconnection of the key, he chooses some ad is behind the part of the menu and redirects the page of this Web site.

  3. when I try to select a Word, words or sections as paragraphs, it performs several different things: continually select as soon as I let go of the mouse button, the jumps of color selection in another part of the document, or deselects the part of the text before I even let go of the mouse button.

  Here is what I tried:

  1. I had originally a usb wireless mouse. I changed the batteries and then got a new. Now I use a wired mouse.

  2 make sure all updates for Windows and Office 2010 are updated.

  3 has tried to update the drivers mouse, says that it is up-to-date. He restored, did not work. Uninstalled and restarted.

  4 Ran Windows Security Essential and Malwarebytes - found nothing.

  5. ensure that all the Toshiba updates were up-to-date.

  I don't know how the word this issue properly in order to find information about it. Everything I typed in search engines brings me other problems unrelated to this one.

  I am running W7 64 x Home Premium SP1, SP2 MS 2010 with a mouse Dell; Toshiba Satellite C655

  Well I have stumbled on the fix... looks like there was a problem with the HID-compliant mouse. The convenience store hardware detected and solved the problem. Everything seems to work properly again.

• Problem with the areo and transparency in Windows 7 after installation of Nvidia Geforce go 6200

  Am having problem with the areo and transparency in Windows 7 after installation of Nvidia Geforce go 6200

  * original title - I'm having a problem *.

  You have the latest drivers?
  http://www.nvidia.com/page/support.html

  Aero - Windows 7 - How to troubleshoot problems with Aero

  (1) first of all, click on the Start button and type in Aero. Now, click on find and fix problems with transparency and other Visual effects of link.

  (2) a new Wizard dialog box opens. Make sure that you click Advanced to solve all problems automatically.

  (3) either the problem will be solved or not. If this isn't the case, you will get a list of items that are potential problems.

  (4) If you want to see more details about the problem, you can click View detailed information. This will give you a list of potential problems that have been verified and those that pose problems.

  If it does not---> click Start---> right click computer---> click Properties

  Click the link for 'Windows performance index' and then click 'rerun the assessment"to refresh your WEI score and try again.

  Note: If you have Windows 7 Starter, or if your system does not meet the requirements for Aero you will not be able to use Aero.

• Problems with Acrobat XI and a pro version

  I uninstalled Acrobat Pro XI and re-installed with a license key valid (as confirmed by Adope JUDGMENT).

  However, when trying to first open the program, I accept the terms and then a windo opens that says:

  "XI acrobat Pro-Testversion; Tagus 00;

  Der Testzeitraum sit abgelaufen. Sie können Acrobat Pro XI weiter use, indem sie die Software kaufen'... "

  But I already bought the Pro Version...

  Best regards

  I am locking this discussion as it continues on a new thread. Please see Re: problems with Acrobat XI and a pro asking for license key version for additional troubleshooting.

• Photoshop elements 13 said that there was a problem with the download and recommend exit us and restart

  We bought a new laptop and 13 items today. We spent the day trying to get it set up. We tried to download the 13 items at least 6 times. Whenever it took about 45 minutes to download, but when we open the file and click on set up it says that there was a problem with the download and it recommends that stop, restart and download it again? How we work what goes wrong? We had to remove the files and start every time. I don't have another day to try to get this sort. Should not it is just a matter of downloading and then, should not come with a message to install and we just press Yes and it works.

  You can also download the trial version of the software directly (No Download Manager) through the page linked below and then use your current serial number to activate it.  You should get two files, an executable file and a compressed file.  Run the executable file and it will install the rest.

  Don't forget to follow the steps described in the Note: very important Instructions in the section on the pages of this site download and have cookies turned on in your browser, otherwise the download will not work correctly.

  Photoshop/Premiere Elements 13: http://prodesigntools.com/photoshop-elements-13-direct-download-links-premiere.html

• Problems with saving files, creating new layouts div fluid

  Problems with saving files, creating new layouts div fluid. Can I reinstall all the software Dreamweaver?

  Thank you

  I reinstalled and all is well.

  Sent from my iPad

• Problems with line spacing and text in Indesign 6 rate

  Hello everyone. I'm a graphic designer working with new magazine layout in Indesign. I used Quark for years and recently fell on this problem...

  In a paragraph, we usually use a soft return back some words to the next line. However, there are opportunities, I notice that in doing so the lines above where I am bumping the word ebb and Exchange. I've never had a problem with this before and it is a serious problem for us. Is it a setting I have on that I'm not aware? What can I do to avoid what is happening?

  Thank you for any input or advice.

  It is one of the main differences between Quark and ID.

  ID has a "paragraph composer" for will as a simple line like Quark composer, and it is enabled by default. When you use the paragraph composer, text is constantly analyzed and spacing adjusted for better form and appearance (according to the spacing algorithm and parameters of your justification) for the whole paragraph. If force you a line break, ID can adjust all the lines above as well as the following lines.

  If it is a 'serious problem' you shoud probably witch to the composer line simple. You will find a drop down for it in the dialog box of the definitin of paragraph under the parameters of the Justification style, or you can change individual paragraph as a local override from the steering wheel to control panel menu.

  Most of us who've been ID user for some time find the paragraph composer include the forces of the ID, and feel that it generates more nice looking text than a single-line composer.