-
Problem with the DHCP server IP address
Hello
a new installation of LAN, two VSS pair core 6509, 15 closets, with piles of 3750. Floor 15 only, host devices can ping the DHCP server, but cannot acquire IP addresses. not this problem on other floors?
PortFast a dother settings are intact.
your thoughts with be appreciated.
Massoud
Are the trunks will switches closets for the vlan, the DHCP server is in?
Sent by Cisco Support technique iPhone App
-
Satellite L870: Problem with USB to serial interface with FTDI chipset
Hi all
bought a L870 year last to run software amateur radio via USB to the serial interface.
Interface uses the FTDI chipset.
The problem I have is that the switch on the led on the interface flashes green to red several times to indicate that it works, but then must remain on green but task on every minute she goes through the same process again.
All the controls on the drivers and the Manager of devices indicates that everything is ok. No problem with interface on computers laptops happens or advent.
Is there anything on the Toshiba laurys usb ports every minute.
Thanking you in advance for any ideas
First of all, I must say that there are different models of L870 Satellite on the market supporting different hardware and software. Some are preinstalled with 8 and some Win with Win 7.
In addition the L870 supports USB 2.0 and USB 3.0 standard.
If you recommend to check the different USB ports and check if your software works correctly with the USB 3.0 standard.
-
Problem with ping VPN cisco 877
Hi all!
I have a working VPN between a fortigate and a Cisco.
I have a problem with ping network behind the cisco of the network behind the forti.
When I ping to vlan2 cisco without problem (192.168.252.1) interface, but I can't ping a server in the vlan2 (192.168.252.2) behind the cisco.
However the Cisco I can ping the server. In the forti, I see that ping to the interface vlan2 and server in vlan2 take in the same way, and I can see package.
I post my config could see it it as blocking the ping from 10.41.2.36 to 192.168.252.2 while 192.168.252.1 ping is OK?
IPSEC #show run
Building configuration...
Current configuration: 3302 bytes
!
! Last modification of the configuration at 14:42:17 CEDT Friday, June 25, 2010
! NVRAM config update at 14:42:23 CEDT Friday, June 25, 2010
!
version 12.4
no service button
horodateurs service debug datetime msec
Log service timestamps datetime localtime show-time zone
encryption password service
!
IPSEC host name
!
boot-start-marker
boot-end-marker
!
logging buffered 1000000
enable secret 5 abdellah
!
No aaa new-model
clock timezone GMT 1
clock to summer time CEDT recurring last Sun Mar 02:00 last Sun Oct 03:00
!
!
dot11 syslog
IP cef
No dhcp use connected vrf ip
DHCP excluded-address IP 192.168.254.0 192.168.254.99
DHCP excluded-address IP 192.168.254.128 192.168.254.255
!
IP dhcp DHCP pool
network 192.168.254.0 255.255.255.0
router by default - 192.168.254.254
Server DNS A.A.A.A B.B.B.B
!
!
no ip domain search
name of the IP-server A.A.A.A
name of the IP-server B.B.B.B
!
!
!
!
!
crypto ISAKMP policy 1
BA aes 256
preshared authentication
Group 5
ISAKMP crypto key ciscokey address IP_forti
!
!
Crypto ipsec transform-set esp - aes 256 esp-sha-hmac vpntest
!
myvpn 10 ipsec-isakmp crypto map
defined by peer IP_forti
Set transform-set vpntest
match address 101
!
Archives
The config log
hidekeys
!
!
!
!
!
interface Tunnel0
IP 2.2.2.1 255.255.255.252
source of Dialer0 tunnel
destination of IP_forti tunnel
myvpn card crypto
!
ATM0 interface
bandwidth 320
no ip address
load-interval 30
No atm ilmi-keepalive
DSL-automatic operation mode
!
point-to-point interface ATM0.1
MTU 1492
bandwidth 160
PVC 8/35
VBR - nrt 160 160
PPPoE-client dial-pool-number 1
!
!
interface FastEthernet0
switchport access vlan 2
!
interface FastEthernet1
!
interface FastEthernet2
!
interface FastEthernet3
switchport access vlan 2
!
interface Vlan1
IP 192.168.20.253 255.255.255.0
IP nat inside
no ip virtual-reassembly
!
interface Vlan2
IP 192.168.252.1 255.255.255.0
IP nat inside
IP virtual-reassembly
!
interface Dialer0
bandwidth 128
the negotiated IP address
NAT outside IP
no ip virtual-reassembly
encapsulation ppp
load-interval 30
Dialer pool 1
Dialer-Group 1
KeepAlive 1 2
Authentication callin PPP chap Protocol
PPP chap hostname [email protected] / * /
PPP chap password 7 abdelkrim
myvpn card crypto
!
IP forward-Protocol ND
IP route 0.0.0.0 0.0.0.0 Dialer0
IP route 10.41.2.32 Tunnel0 255.255.255.240
!
no ip address of the http server
no ip http secure server
The dns server IP
translation of nat IP tcp-timeout 5400
no ip nat service sip 5060 udp port
overload of IP nat inside source list NAT interface Dialer0
!
IP access-list standard BROADCAST
permit of 0.0.0.0
deny all
!
NAT extended IP access list
IP enable any host IP_cisco
deny ip 192.168.252.0 0.0.0.255 10.41.2.32 0.0.0.31
!
access-list 101 permit ip 192.168.252.0 0.0.0.255 10.41.2.32 0.0.0.31
public RO SNMP-server community
3 RW 99 SNMP-server community
SNMP-server community a RO
SNMP-Server RO community oneCommunityRead
not run cdp
!
!
!
control plan
!
!
Line con 0
password 7 abdelkrim
opening of session
no activation of the modem
line to 0
line vty 0 4
password 7 aaaaa
opening of session
escape character 5
!
max-task-time 5000 Planner
NTP-period clock 17175037
Server NTP B.B.B.B
Server NTP A.A.A.A
end
Alex,
It's your GRE tunnel:
interface Tunnel0
IP 2.2.2.1 255.255.255.252
source of Dialer0 tunnel
destination of IP_forti tunnel
myvpn card crypto
You also have routing set by it.
You don't need a GRE tunnel, nor do you need the road to tunnel if you want just IPsec tunnel.
-
Problem with Tunnel VPN L2L between 2 ASA´s
Hi guys,.
I have some problems with my VPN Site to site tunnel between 2 ASA (5520/5505).
I watched a lot of videos on youtube, but I can't find out why the tunnel does not...
Both devices can ping eachothers WAN IP address (outside interfaces), but I don't see any traffic between the 2 sites. It seems that the tunnel is not open to everyone. When i PING from the local to the Remote LAN (which should be an interesting traffic for the tunnel...), the its IKEv1 remains empty...
Am I missing something? I can't understand it more why same phase 1 is not engaged.
You NAT won't. In your config file traffic is NATted initially and then does not match any more crypto ACL. You must move the rule dynamic NAT/PAT until the end of the table on two ASAs NAT:
no nat (INSIDE,OUTSIDE) source dynamic any interface nat (INSIDE,OUTSIDE) after-auto source dynamic any interface
-
Problems with remote access IPSec VPN
Dear Experts,
Kindly help me with this problem of access VPN remotely.
I have configured remote access VPN IPSec using the wizard. The remote client connects to fine enough seat, gets the defined IP address, sends the packets and bytes, BUT do not receive all the bytes or decrypt packets. On the contrary, the meter to guard discarded rising.
What could be possibly responsible or what another configuration to do on the SAA for the connection to be fully functional?
It can help to say that Anyconnect VPN is configured on the same external Interface on the ASA, and it is still functional. What is the reason?
AnyConnect VPN is used by staff for remote access.
Kindly help.
Thank you.
Hello
So if I understand correctly, you have such an interface for LAN and WAN and, naturally, the destination networks you want to reach via the VPN Client connection are all located behind the LAN interface.
In this case the NAT0 configuration with your software most recent could look like this
object-group, LAN-NETWORKS-VPN network
network-object
network-object
network-object
network of the VPN-POOL object
subnet
destination of LAN-NETWORKS-VPN VPN-NETWORKS-LAN static NAT (LAN, WAN) 1 static source VPN-VPN-POOL
Naturally, the naming of interfaces and objects might be different. In this case its just meant to illustrate the purpose of the object or interface.
Naturally I'm not sure if the NAT0 configuration is the problem if I can't really say anything for some that I can't see the configuration.
As for the other question,
I have not implemented an ASA to use 2 interfaces so WAN in production environments in the case usually has separate platforms for both or we may be hosting / providing service for them.
I imagine that there are ways to do it, but the main problem is the routing. Essentially, we know that the VPN Client connections can come from virtually any public source IP address, and in this case we would need to default route pointing to the VPN interface since its not really convenient to set up separate routes for the IP address where the VPN Client connections would come from.
So if we consider that it should be the default route on the WEBSITE of the ASA link, we run to the problem that we can not have 2 default routes on the same active device at the same time.
Naturally, with the level of your software, you would be able to use the NAT to get the result you wanted.
In short, the requirements would be the following
- VPN interface has a default route, INTERNET interface has a default route to value at the address below
- NAT0 between LAN and VPN interface configuration to make sure that this traffic is passed between these interface without NAT
- Interfaces to special NAT configuration between LAN and INTERNET which would essentially transfer all traffic on the INTERNET interface (except for VPN traffic that we have handled in the previous step)
The above things would essentially allow the VPN interface have the default route that would mean that no matter what the VPN Client source IP address it should be able to communicate with the ASA.
The NAT0 configuration application would be to force ASA to pass this traffic between the LAN and VPN (pools) for VPN traffic.
The special configuration of NAT then match the traffic from LAN to ANY destination address and send to the INTERNET interface. Once this decision is made the traffic would follow the lower value default route on this interface.
I would say that this isn't really the ideal situation and the configuration to use in an environment of productin. It potentially creates a complex NAT configuration such that you use to manipulate the traffic instead of leave the mark of table routing choice in the first place.
Of course, there could be other options, but I have to test this configuration before I can say anything more for some.
-Jouni
-
Problem with "vpn sysopt connection permit.
Hi all
I would like to ask you for advice with "vpn sysopt connection permit". I have a problem with by-pass-access list (acl) in the INSIDE interface. As I understand it and I'm going to use this command, there is no need to especialy allow traffic in the access list for the INSIDE and I can control the filter-vpn traffic. But in my case it's quite the opposite, I want particularly to this INTERIOR acl traffi. When I allow this traffic inside acl L2L tunnel rises, hollow traffic flow vpn-fltr ane acl that everything is OK. But when I do not allow that this traffic is inside of the rule with Deny statement in acl INSIDE block traffic and tunnel goes ever upward. Part of the configuraciton which you can view below.
Please let me know if I'm wrong, or what I did wrong?
Thank you
Karel
PHA-FW01 # view worm | Worm Inc
Cisco Adaptive Security Appliance Software Version 4,0000 1
PHA-FW01 # display ru all sys
No timewait sysopt connection
Sysopt connection tcpmss 1380
Sysopt connection tcpmss minimum 0
Sysopt connection permit VPN
Sysopt connection VPN-reclassify
No sysopt preserve-vpn-stream connection
no RADIUS secret ignore sysopt
No inside sysopt noproxyarp
No EXT-VLAN20 sysopt noproxyarp
No EXT-WIFI-VLAN30 sysopt noproxyarp
No OUTSIDE sysopt noproxyarp
PHA-FW01 # display the id of the object-group ALGOTECH
object-group network ALGOTECH
object-network 10.10.22.0 255.255.255.0
host of the object-Network 172.16.15.11
PHA-FW01 # show running-config id of the object VLAN20
network of the VLAN20 object
subnet 10.1.2.0 255.255.255.0
L2L_to_ALGOTECH list extended access permitted ip object object-group VLAN20 ALGOTECH
extended access list ACL-ALGOTECH allow ip object-group object VLAN20 ALGOTECH
Note EXT-VLAN20 of access list =.
access list EXT-VLAN20 allowed extended ip object VLAN20 ALGOTECH #why object-group must be the rule here?
access list EXT-VLAN20 extended permitted udp object VLAN20 object-group OUT-DNS-SERVERS eq field
EXT-VLAN20 allowed extended VLAN20 object VPN-USERS ip access list
EXT-VLAN20 extended access list permit ip object VLAN20 OPENVPN-SASPO object-group
EXT-VLAN20 allowed extended object VLAN10 VLAN20 ip access list
deny access list extended VLAN20 EXT ip no matter what LOCAL NETS of object-group paper
EXT-VLAN20 allowed extended icmp access list no echo
access list EXT-VLAN20 allowed extended object-group SERVICE VLAN20 object VLAN20 everything
EXT-VLAN20 extended access list deny ip any any newspaper
extended access list ACL-ALGOTECH allow ip object-group object VLAN20 ALGOTECH
GROUP_POLICY-91 group policy. X 41. X.12 internal
GROUP_POLICY-91 group policy. X 41. X.12 attributes
value of VPN-filter ACL-ALGOTECH
Ikev1 VPN-tunnel-Protocol
tunnel-group 91.X41. X.12 type ipsec-l2l
tunnel-group 91.X41. X.12 General attributes
Group Policy - by default-GROUP_POLICY-91. X 41. X.12
tunnel-group 91.X41. X.12 ipsec-attributes
IKEv1 pre-shared-key *.
PHA-FW01 # show running-config nat
NAT (EXT-VLAN20, outdoors) static source VLAN20 VLAN20 static destination ALGOTECH ALGOTECH non-proxy-arp-search to itinerary
network of the VLAN20 object
dynamic NAT interface (EXT-VLAN20, outdoors)
group-access to the INTERIOR in the interface inside
Access-group interface VLAN20 EXT EXT-VLAN20
Hello
The command "sysopt connection permit-vpn" is the default setting and it applies only to bypass ACL interface to the interface that ends the VPN. It would be connected to the external network interface. This custom has no effect on the other interfaces ACL interface.
So if you initiate or need to open connections from your local network to remote network through the VPN L2L connection then you will need to allow this traffic on your LAN interface ACL networks.
If the situation was that only the remote end has launched connections to your network then 'sysopt permit vpn connection' would allow their connections around the external interfaces ACL. If If you have a VPN configured ACL filter, I think that the traffic will always accompany against this ACL.
Here are the ASA reference section to order custom "sysopt"
http://www.Cisco.com/en/us/docs/security/ASA/command-reference/S21.html#wp1567918
-Jouni
-
Problem with VPN
I have two problems with IPSEC VPN, using the cisco client, and a third, which I think could answer here if this isn't strictly associated with VPN.
1. cannot access the internet, while VPN is in place. This can be a problem of client as I * think * I've split tunneling to install correctly.
2. cannot access other networks except the network associated with the inside interface natively.
3. I can not ping to the internet from inside, be it on the VPN or not.
I tend to use the SMDA; Please, if possible, keep the answer to this kindof of entry.
Here is the config:
Output of the command: "sh run".
: Saved
:
ASA Version 8.4 (1)
!
hostname BVGW
domain blueVector.com
activate qWxO.XjLGf3hYkQ1 encrypted password
2KFQnbNIdI.2KYOU encrypted passwd
names of
!
interface Ethernet0/0
nameif outside
security-level 10
IP 5.29.79.10 255.255.255.248
!
interface Ethernet0/1
nameif inside
security-level 100
IP 172.17.1.2 255.255.255.0
!
interface Ethernet0/2
Shutdown
No nameif
no level of security
no ip address
!
interface Ethernet0/3
Shutdown
No nameif
no level of security
no ip address
!
interface Management0/0
nameif management
security-level 100
IP 172.19.1.1 255.255.255.0
management only
!
passive FTP mode
DNS server-group DefaultDNS
domain blueVector.com
permit same-security-traffic inter-interface
permit same-security-traffic intra-interface
the subject of WiFi network
172.17.100.0 subnet 255.255.255.0
WiFi description
the object to the Interior-net network
172.17.1.0 subnet 255.255.255.0
network of the NOSPAM object
Home 172.17.1.60
network of the BH2 object
Home 172.17.1.60
the EX2 object network
Home 172.17.1.61
Description internal Exchange / SMTP outgoing
the Mail2 object network
Home 5.29.79.11
Description Ext EX2
network of the NETWORK_OBJ_172.17.1.240_28 object
subnet 172.17.1.240 255.255.255.240
network of the NETWORK_OBJ_172.17.200.0_24 object
172.17.200.0 subnet 255.255.255.0
DM_INLINE_TCP_1 tcp service object-group
port-object eq www
EQ object of the https port
the DM_INLINE_NETWORK_1 object-group network
network-object BH2
network-object NOSPAM
Outside_access_in list extended access permit tcp any eq smtp DM_INLINE_NETWORK_1 object-group
Outside_access_in list extended access permit tcp any object object-group DM_INLINE_TCP_1 BH2
pager lines 24
Enable logging
asdm of logging of information
Outside 1500 MTU
Within 1500 MTU
management of MTU 1500
mask pool local 172.17.1.240 - 172.17.1.250 VPN IP 255.255.255.0
mask pool local 172.17.200.100 - 172.17.200.200 VPN2 IP 255.255.255.0
no failover
ICMP unreachable rate-limit 1 burst-size 1
don't allow no asdm history
ARP timeout 14400
NAT (inside, outside) static source EX2 Mail2
NAT (inside, outside) static source all all NETWORK_OBJ_172.17.1.240_28 of NETWORK_OBJ_172.17.1.240_28 static destination
NAT (inside, outside) static source all all NETWORK_OBJ_172.17.200.0_24 of NETWORK_OBJ_172.17.200.0_24 static destination
NAT (inside, outside) static source to the Interior-NET Interior-net destination static NETWORK_OBJ_172.17.1.240_28 NETWORK_OBJ_172.17.1.240_28
!
the object to the Interior-net network
NAT (inside, outside) dynamic interface
network of the NOSPAM object
NAT (inside, outside) static 5.29.79.12
Access-group Outside_access_in in interface outside
Route outside 0.0.0.0 0.0.0.0 5.29.79.9 1
Route inside 10.2.0.0 255.255.255.0 172.17.1.1 1
Route inside 10.3.0.0 255.255.255.128 172.17.1.1 1
Route inside 10.10.10.0 255.255.255.0 172.17.1.1 1
Route inside 172.17.100.0 255.255.255.0 172.17.1.3 1
Route inside 172.18.1.0 255.255.255.0 172.17.1.1 1
Route inside 192.168.1.0 255.255.255.0 172.17.1.1 1
Route inside 192.168.11.0 255.255.255.0 172.17.1.1 1
Route inside 192.168.30.0 255.255.255.0 172.17.1.1 1
Timeout xlate 03:00
Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
dynamic-access-policy-registration DfltAccessPolicy
AAA-server blueVec protocol ldap
blueVec AAA-server (inside) host 172.17.1.41
LDAP-base-dn DC = adrs1, DC = net
LDAP-group-base-dn DC = EIM, DC = net
LDAP-scope subtree
LDAP-naming-attribute sAMAccountName
LDAP-login-password *.
LDAP-connection-dn CN = Hanna\, Roger, OU = human, or = WPLAdministrator, DC = adrs1, DC = net
microsoft server type
Enable http server
http 192.168.1.0 255.255.255.0 management
http 172.17.1.0 255.255.255.0 inside
http 24.32.208.223 255.255.255.255 outside
No snmp server location
No snmp Server contact
Server enable SNMP traps snmp authentication linkup, linkdown warmstart of cold start
Crypto ipsec transform-set ikev1 ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-DES-SHA esp - esp-sha-hmac
Crypto ipsec transform-set ikev1 esp ESP-DES-MD5-esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-3DES-MD5-esp-3des esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
Crypto ipsec transform-set ikev1 ESP-AES-128-SHA aes - esp esp-sha-hmac
Crypto ipsec transform-set ikev1 ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
Crypto ipsec transform-set ikev1 ESP-AES-128-MD5-esp - aes esp-md5-hmac
Crypto ipsec transform-set ikev1 SHA-ESP-3DES esp-3des esp-sha-hmac
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 define ikev1 transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5
card crypto Outside_map 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP
Outside_map interface card crypto outside
Crypto ikev1 allow outside
IKEv1 crypto policy 10
preshared authentication
3des encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 30
authentication crack
3des encryption
sha hash
Group 2
life 86400
Telnet timeout 5
SSH 172.17.1.0 255.255.255.0 inside
SSH timeout 5
Console timeout 0
dhcpd address 172.17.1.100 - 172.17.1.200 inside
dhcpd 4.2.2.2 dns 8.8.8.8 interface inside
dhcpd lease interface 100000 inside
dhcpd adrs1.net area inside interface
!
a basic threat threat detection
threat detection statistics
a statistical threat detection tcp-interception rate-interval 30 burst-400-rate average rate 200
WebVPN
internal blueV group policy
attributes of the strategy of group blueV
value of server WINS 172.17.1.41
value of 172.17.1.41 DNS server 172.17.1.42
Ikev1 VPN-tunnel-Protocol
value by default-field ADRS1.NET
internal blueV_1 group policy
attributes of the strategy of group blueV_1
value of server WINS 172.17.1.41
value of 172.17.1.41 DNS server 172.17.1.42
Ikev1 VPN-tunnel-Protocol
Split-tunnel-policy tunnelspecified
adrs1.NET value by default-field
username gwhitten encrypted password privilege 0 8fLfC1TTV35zytjA
username gwhitten attributes
VPN-group-policy blueV
rparker encrypted FnbvAdOZxk4r40E5 privilege 15 password username
attributes of username rparker
VPN-group-policy blueV
username mhale encrypted password privilege 0 2reWKpsLC5em3o1P
username mhale attributes
VPN-group-policy blueV
VpnUser2 SlHbkDWqPQLgylxJ encrypted privilege 0 username password
username VpnUser2 attributes
VPN-group-policy blueV
Vpnuser3 R6zHxBM9chjqBPHl encrypted privilege 0 username password
username Vpnuser3 attributes
VPN-group-policy blueV
username VpnUser1 encrypted password privilege 0 mLHXwxsjJEIziFgb
username VpnUser1 attributes
VPN-group-policy blueV
username dcoletto encrypted password privilege 0 g53yRiEqpcYkSyYS
username dcoletto attributes
VPN-group-policy blueV
username, password jmcleod aSV6RHsq7Wn/YJ7X encrypted privilege 0
username jmcleod attributes
VPN-group-policy blueV
rhanna encrypted Pd3E3vqnGmV84Ds2 privilege 15 password username
rhanna attributes username
VPN-group-policy blueV
username rheimann encrypted password privilege 0 tHH5ZYDXJ0qKyxnk
username rheimann attributes
VPN-group-policy blueV
username jwoosley encrypted password privilege 0 yBOc8ubzzbeBXmuo
username jwoosley attributes
VPN-group-policy blueV
2DBQVSUbfTBuxC8u encrypted password privilege 0 kdavis username
kdavis username attributes
VPN-group-policy blueV
username mbell encrypted password privilege 0 adskOOsnVPnw6eJD
username mbell attributes
VPN-group-policy blueV
bmiller dpqK9cKk50J7TuPN encrypted password privilege 0 username
bmiller username attributes
VPN-group-policy blueV
type tunnel-group blueV remote access
tunnel-group blueV General-attributes
address VPN2 pool
authentication-server-group blueVec
Group Policy - by default-blueV_1
blueV group of tunnel ipsec-attributes
IKEv1 pre-shablue-key *.
!
class-map inspection_default
match default-inspection-traffic
!
!
type of policy-card inspect dns preset_dns_map
parameters
maximum message length automatic of customer
message-length maximum 512
Policy-map global_policy
class inspection_default
inspect the preset_dns_map dns
inspect the ftp
inspect h323 h225
inspect the h323 ras
inspect the rsh
inspect the rtsp
inspect esmtp
inspect sqlnet
inspect the skinny
inspect sunrpc
inspect xdmcp
inspect the sip
inspect the netbios
inspect the tftp
Review the ip options
!
global service-policy global_policy
context of prompt hostname
call-home
Profile of CiscoTAC-1
no active account
http https://tools.cisco.com/its/service/oddce/services/DDCEService destination address
email address of destination [email protected] / * /
destination-mode http transport
Subscribe to alert-group diagnosis
Subscribe to alert-group environment
Subscribe to alert-group monthly periodic inventory
monthly periodicals to subscribe to alert-group configuration
daily periodic subscribe to alert-group telemetry
HPM topN enable
Cryptochecksum:2491a825fb8a81439a6c80288f33818e
: end
Any help is appreciated!
-Roger
Hey,.
Unfortunately, I do not use ASDM myself but will always mention things that could be done.
You do not split tunneling. All traffic either tunnel to the ASA, while VPN is active
You have the following line under the "group policy"
Split-tunnel-policy tunnelspecified
You will also need this line
Split-tunnel-network-list value
Defines the destination for the VPN Client networks. If you go in on the side of the ASDM group policy settings, you should see that no ACL is selected. You don't really seem to have an ACL in the configuration above, for the split tunneling?
To activate access Internet via the VPN Client now in the current configuration, I would say the following configuration of NAT
VPN-CLIENT-PAT-SOURCE network object-group
object-network 172.17.200.0 255.255.255.0
NAT (outside, outdoor) automatic interface after dynamic source VPN-CLIENT-PAT-SOURCE
In regards to the traffic does not for other networks, I'm not really sure. I guess they aren't hitting the rule NAT that are configured. I think they should, but I guess they aren't because its does not work
I could myself try the following configuration of NAT
object-group, network LAN-NETWORKS
object-network 10.2.0.0 255.255.255.0
object-network 10.3.0.0 255.255.255.128
object-network 10.10.10.0 255.255.255.0
object-network 172.17.100.0 255.255.255.0
object-network 172.18.1.0 255.255.255.0
object-network 192.168.1.0 255.255.255.0
object-network 192.168.11.0 255.255.255.0
object-network 192.168.30.0 255.255.255.0
object-group, network VPN-POOL
object-network 172.17.200.0 255.255.255.0
NAT (inside, outside) static static source of destination LAN-LAN-NETWORK VPN-VPN-POOL
Add ICMP ICMP Inspection
Policy-map global_policy
class inspection_default
inspect the icmp
or alternatively
fixup protocol icmp
This will allow automatically response to ICMP echo messages pass through the firewall. I assume that they are is blocked by the firewall now since you did not previously enable ICMP Inspection.
-Jouni
-
Problem with DHCP broadcast between VLAN
Hello
I trying to solve the lab that I set up, I have a problem with broadcast between VLANS with my DHCP. I looked around the vmware community to find my answer, but I did not who is right why I post here!
So here's my situation :
- ESX with 2 race of VM:
- An R2 of 2012 Windows running a DHCP server with a configured scope
- This virtual machine is assigned to the vmnic4 with the port VLAN 100 group
- A Windows 7, which I use as a customer
- This virtual machine is assigned to the vmnic4 with the port VLAN 110 group
- Switch Cisco with a simple configuration:
interface FastEthernet0/1
Description LINK FOR ESX
switchport mode trunk
switchport nonegotiate
interface FastEthernet0/24
Description OF LINK ROUTER
switchport mode trunk
- Configuration of the Cisco "router on the stick:
interface FastEthernet0/0.100
encapsulation dot1q 100
10.1.1.254 IP address 255.255.255.0
interface FastEthernet0/0,110
encapsulation dot1q 110
IP 10.1.2.254 255.255.255.0
IP helper 10.1.1.0
The resolution of the problems that I did:
- Affecting the client static IP and that both virtual machine can ping each other
- Moving from the client to the same VLAN as DHCP server, and the DHCP server is to give the client an IP address.
- Sniffing the packet:
- I can see the client DHCPDiscover
- I can see the router with the command "debug ip dhcp server packet" package passed on the 10.1.1.0.
- I am not able to see the packets from the router to DHCP perspective
That's why I guess miss me something ESX configuration.
Thanks in advance for reading this post!
PS: I've linked a vswitch configuration screenshot
I think that you have configured an incorrect address of IP support, take a look at the following line:
IP helper 10.1.1.0
Your DCHP server is really 10.1.1.0? I think not, since 10.1.1.0 corresponds to the ID of the network 10.1.1.0/24 network.
-
Satellite L670-1HD - problem with audio interfaces USB 1.1
Hello
I have a Toshiba L670-1HD with an Intel HM55 chipset, and an Intel Core i5 460M processor. I use this machine for my music software and that's why I use different audio interfaces external and USB-MIDI-Controller with build in audio interface like Mixvibes U - Mix Control Pro (http://www.mixvibes.com/content/u-mix-control-pro). These built-in audio interface are connected via USB 1.1. Always when I use this audio interfaces interfaces crash audio internalt - the sound is cracked very hard and there are noises in. The controller of all crashes sometimes too.
When I use another interface audio as an audio interface Hercules DJ Trim 4 & 6 (http://www.hercules.com/uk/DJ-Music/bdd/p/102/deejay-trim-4-6/), which is a USB 2.0, everything works fine. No crashes, no cracks and no noise.
You could say now that there is no problem and I should stick to the Hercules interface if it does no problem. The problem is that the Hercules is an audio interface only, there is no controller in it with which I can control my music software.
I've updated all the drivers from the support page of this site without success. Is there a solution available or the Toshiba knows this subject? Am I the only one having this problem?
Would be nice if a Toshiba official support employer could respond to this message. But this does not mean that I don't want to read somethng submitted by the user for which an index - all Board/Council/recommendation is welcome.
Thanks in advance for the help!
See you soon,.
Stefan
Hello Stefan
In my view, you see the problem from the wrong point of view.
Toshiba and each laptop manufacturer offer product and hardware and software support. So if there is a general problem with the functionality of the material you are by Toshiba on the right address.
You use a third party and that you have some problems. Do you really believe Toshiba should support you and help to get this external peripheral work? In my opinion not. On the market, there are thousands of different devices and laptop computer how of the manufacturer must be able to test each of them and offer a solution?
Something like that is definitely not possible.
In my opinion, you should communicate with Mixvibes and ask for help. They have the best experience with own product and I presume that they are testing the features on different PC/laptop platforms.
They should know how the device should work on new laptops with USB 2.0.
It seems silly now, but Toshiba has nothing to do with it. If you have a general problem with the USB ports and they don t work with different devices that Toshiba should ask for help.
-
ProBook 650 1: Problems with W10 upgrade - Client VPN in my notebook?
Hello
I upgraded my laptop to Windows 10 but, like many people, I encountered some problems with the Broadcom 802.11 wi - fi adapter. I read a lot of discussion about it and I decide to yestarday to roll back to Windows 7 in order to do a clean update by ISO and unisntall VPN. I read that Cisco VPN Client is the problem when upgrading to W10... but I'm not sure I have the Cisco Client in my notebook.
You help me find a software which VPN I have in my book?
I run Microsoft Fixit and found out that I have:
Cisco PEAP
Cisco LEAP
Cisco EAP-FAST
Is this software VPN? Or not?
After having updated Broadcom driver on Windows 10 WiFi worked well, but I still had an error message ' Broadcom 802.11 network adapter wi - fi doesn't work "whenever I turned on the laptop.
In addition, it was impossible on W10 to open the Broadcom Wireless Tool (Control Panel) software, I always get an error message.
Should I unistall Cisco software?
See you soon,.
Marco
"Hi @Kreiskybill,
I'm sorry that was meant to be an internal memo that I'm not trained on commercial products and I was hoping one of my colleagues would help, but I'll try my best to help you.
For your wireless problem, there are several troubleshooting documents available on the page of product support for your ProBook (http://ow.ly/ADK7301hCLl), that might be useful. Also, here is the 'HP PC' document - troubleshooting wireless network and the Internet (Windows 10) consumer ( http://ow.ly/pIm0301hEIN ) for reference.
With regard to programs of Cisco that you listed, @SpiritX on the Microsoft Forums ( http://ow.ly/DAhQ301hCFt ) well answer your question about Cisco programs you listed. I know that you are not running Windows Vista, but the answer is always valid for you.
If it helps and you want to thank me, please click the 'Thumbs Up' icon to say thank you. If you think that I helped to solve your problem, please click the button of "acceptable Solution". This will allow other users to find what worked for you. »
-
Problem with PCI-GPIB card control Agilent 8648 D generator interface
Hello
I downloaded the driver Plug-and-Play (project-style) for Agilent 8648 A generator of signals. I use LabVIEW 2011.
I open the file project and resource VISA name menu, select COM1. Note that I use 82350B of the PCI-GPIB Interface Card.
I run the project, and I get timeout error.
Is there a problem in the PCI-GPIB interface or am I missing something? I'm new to LabView and PCI-GPIB interface, and I'd appreciate any help.
Thank you
Nabil Gharib
Given that you do not use a NI GPIB, go to MAX, select software and NI-VISA. In the right window, click the Options of VISA, and then select passports under general settings. Check on the passport of NI-VISA for Tulip.
I'm assumimg you loaded the driver of Agilent and tested the communication with their software.
-
Cisco VPN problem with security update KB3057839 for Vista
Someone had problems with any connection Cisco VPN works after the installation of update of security KB3057839 for Vista? When this update is installed, the pop-up to enter the password and user id not come, need to use the Task Manager to close the program. The first time I went back to the restore point to get my VPN to work, this time I tried to reinstall the VPN but that doesn't work anymore. I started to uninstall updates (had 7 of them), when I got to it, KB3057839, the VPN began working again.
Mike
See this on the real issue:
http://www.chiark.greenend.org.uk/~sgtatham/PuTTY/wishlist/Vista-update-breaks-config.html
It turns out that the logon dialog box is invisible, but still, it agrees to enter you your password and LOG you!
-
OfficeJet 6700 DHCP causing problems with airprint and web services
I find it kind of interesting that this printer does not properly with DHCP enabled by default and more easy to use configuration. My new printer seems to require to manually set the ip and dns settings before the features of web services or airprint worked correctly. It was strange because printing from a PC and iMac worked well, it was that only the web services feature (unable to connect to the server) and the airprint from IOS devices failed (printer shows up but just disappeared rather than printing impression actually). Someone else has seen this and not do anything to solve this problem?
The problem with this is effectively resolved through static DNS, generally. The reason it is and not with other functions, is that our print servers that connect you with are able to communicate more easily with some DNS configurations on the other.
For this reason, HP recommends generally defining the DNS for your printer on the parameters of Google DNS: 8.8.8.8 & 8.8.4.4.
Does that answer your question?
Have a great day!
-
Problem with user API 5.0 interface components
Hello!
I have a problem with the user interface components.
My application needs of the analogues of the toolbar and PaneManager (as in api 6 and higher) in BB API 5, but I have no idea how to make them.
Please, need help
Toolbar can be made with evenlyspacedhorizontalfieldmanager in the Advanced UI package available on the java dev site of bb.