Program of build error

Similar Questions

• Build error cannot find the distribution under construction

  I had a similar problem like this thread.

  http://forums.NI.com/T5/LabVIEW/build-error-can-t-find-distribution-being-built/TD-p/1462842/page/2

  My old guard Installer and ask for copy of the installation is finish. Quite annoying because it takes so long to get there. Any advice would be appreciated. I've attached a screenshot of my error message.

  You created this problem by running a build already install on your development computer. If you are distributing drivers with your installer you should NEVER run the installation program on the machine on which you build.

  Here's what happens:

  All software shops NOR where it was installed since in the Windows registry. When you initially installed it note where you install (DVD, network drive, etc.).

  When you build an installer in TestStand will prompt for this location if it cannot find the original installation files (that is, if you take the DVD from the drive disconnected from the PC from the network, etc.)

  What happened on this PC is you have to build a Setup program, and then you run this installer on the PC, and because the pilots were already present it replaced the path stored in the registry with the path where your Installer (e.g.) was C:\Temp\long path)

  I'm guessing that you have now deleted this former Installer. That means that you have to re - run installers for ALL the software to, OR that you have installed on this machine so the registry is updated to point to the path of DVD or the network path.

• Ant with WebLogic 10.3 build error

  Hello
  
  I'm trying to compile the web service example in the tutorial
  
  http://download.Oracle.com/docs/CD/E12840_01/WLS/docs103/webserv/use_cases.html#wp228687
  
  Use case # 1
  
  And I get this error when you try the command "> ant-build service:
  >
  D:\myExamples\hello_world\src > ant build_service
  BuildFile: D:\myExamples\hello_world\src\build.xml
  
  BUILD FAILED
  D:\myExamples\hello_world\src\build.XML:4: taskdef class weblogic.wsee.tools.anttasks.JwscTask is not found
  by using the [AntClassLoader] class loader
  
  Total time: 0 seconds
  
  
  At this point in the tutorial, the build.xml file contains:
  >
  < name of project = 'webservices-hello_world"default ="all">
  
  < taskdef = "jwsc" name
  ClassName = "WebLogic.WSEE.Tools.anttasks.JwscTask" / > "
  
  < name target = "build-service" >
  
  < jwsc
  srcdir = "src".
  DESTDIR = "production/helloWorldEar" >
  
  "< file="examples/webservices/hello_world/HelloWorldImpK.java TJ.
  Type = "JAXWS" / >
  
  < / jwsc >
  
  < / target >
  < / project >
  
  
  I wonder if I need to set a variable in the environment?
  
  I know that my Ant installation is good since I managed to compile and run a java program with a manifesto in the jar.
  
  Thanks a lot for your help.

  chk this
  Re: build errors using Ant

  1. If you are working from the user_projects directory, add the following to the Properties section of the generation xml "". "" Other wise, set the value the full path of the directory on the server wlserver_10.3 lib directory.

  2. in each taskdef element, add the following child element
  
  
  
  
  
  
  
  
  3. Save and run the ant task in your project directory.

• Build error when you create the Provisioning package picture

  Hi all

  I'm trying to create a master Windows IOT image by using the tool of IDC (imaging and designer of Configuration).

  I created a package of commissioning and using"customization of the Windows Image" to create a kernel ITO image by specifying the configuration previously created package but still get a build error.

  It looks like a fairly simple process, but repeatedly gives the error below. Also, I have not all USB devices connected to the computer, nor are there insufficient memory problems.

  ERROR

  =====

  Progress of the staging: 75%
  Staging failed to: 75% complete
  UpdateDLL: Measurement of results:
  Staging of total time: seconds = 27 (tickcount = 27235)
  Error: imagery! UpdateImage: Failed call to UpdateDLL::PrepareUpdate with the error code:-2145877241 (0 x 80188307)
  DismountVirtualHardDiskByFileName: disassembly image C:\Users\Shridhar\AppData\Local\Temp\8eceab63e9b746c0a9c65848679d56eb.vhd
  DismountFullFlashImage: [0.219] cleanup of temporary access roads.
  CleanupTemporaryPaths: Cleaning of temporary path C:\Users\Shridhar\AppData\Local\Temp\IMG39F3.tmp\.
  Storage service: disassembly of the image in 0.2 seconds.
  Imaging: See Flash.cbs.log and Flash.csi.log for more details.
  Imaging: Performance results:
  Total running time: 00:00:52.7198674
  Time of image creation: 00:00:00.0642425
  Writing FFU Time: 00:00:00
  Battery storage time: 00:00:17.8667874

  Any help would be greatly appreciated.

  Hello

  Your question is beyond the scope of this community...

  Repost in the TechNet Forums:

  https://social.technet.Microsoft.com/forums/en-us/home

  Or MSDN Forums:

  https://social.msdn.Microsoft.com/forums/en-us/home

  See you soon.

• Add/Remove Program runtime Server error - the name or address cannot be resolved

  try to add/remove programs win XP computer

  get the error:
  runtime error (8:634) msxml3.dll the server name or address cannot be resolved
  ran hitman pro and trend micro antivirus scans that removed a malware infection
  that is not the program causing this error - who took ok I guess.
  I'm so gone in my program list to delete all those which I think are dubious or is no longer necessary
  all the rest have been removed ok.

  Hi Silverwand,

  ·         Exactly how are you trying to access to add or remove programs?

  ·         Is the limited any question by going to add or remove the tool program or with other tools as well in Control Panel?

  ·         Did you do changes on the computer before the show?

  Follow the suggestions below for a possible solution:

  Method 1: You can try to run add or remove program through the key to execution and check

  a. press the Windows key + R

  b. type appwiz.cpl and press on ENTRY.

  Method 2: You can try to re - register the msxml3.dll file and check.

  If the file is in the correct path to the right size, then try and re-save the file.

  a. click on Start

  b. click run

  c. type: regsvr32 msxml3.dll

  d. click enter

  e. restart your computer.

  Method 3: I suggest that scan you SFC [SFC system] on the computer that would be a system file corrupt on the computer search and replace.

  a. click Start, click run, type cmd in the Open box and then click OK.

  b. at the command prompt, type sfc/scannow, and then press ENTER.

  Note: Could you prompt to insert the Windows XP CD.

  The sfc/scannow command. analyzes all protected system files and replaces incorrect versions with appropriate Microsoft versions.

  For more information, you can consult the following article:

    

  Description of Windows XP and Windows Server 2003 System File Checker (Sfc.exe)

   http://support.Microsoft.com/kb/310747/en-us

  Let us know if that helps.

• most programs now get error message "could not start from this location after a mail there is session 2 nite".

  After a session 2 nites E-mail there, many programs said message error "could not start program from this location. In addition, long delays after you clicked on a link, a large display hourglass for up to several minutes. Have tried to rebuild, but I think that the problem is still there. Any suggestions?

  What is a "mail session?

  What is, "have tried to rebuild?"

  Edition with Service Pack of Windows XP _ _?

  What anti-virus application that you use, and if she slept in day?

  Search for malware:

  Download, install, execute, update and perform analyses complete system with the two following applications:

  • MalwareBytes (FREE)
  • SuperAntiSpyware (FREE)

  Remove anything they find.  Reboot when necessary.  (You can uninstall one or both when finished.)

  Search online with eSet Online Scanner.

  The less you have to run all the time, most things you want to run will perform:

  Use Autoruns to understand this all starts when your computer's / when you log in.  Look for whatever it is you do not know using Google (or ask here.)  You can hopefully figure out if there are things from when your computer does (or connect) you don't not need and then configure them (through their own built-in mechanisms is the preferred method) so they do not - start using your resources without reason.

  You can download and use Process Explorer to see exactly what is taking your time processor/CPU and memory.  This can help you to identify applications that you might want to consider alternatives for and get rid of all together.

  Do a house cleaning and the dust of this hard drive:

  You can free up disk space (will also help get rid of the things that you do not use) through the following steps:

  Windows XP should take between 4.5 and 9 GB * with * an Office suite, editing Photo software, alternative Internet browser (s), various Internet plugins and a host of other things installed.

  If you are comfortable with the stability of your system, you can delete the uninstall of patches which has installed Windows XP...
  http://www3.TELUS.NET/dandemar/spack.htm
  (Especially of interest here - #4)
  (Variant: http://www.dougknox.com/xp/utils/xp_hotfix_backup.htm )

  You can run disk - integrated into Windows XP - cleanup to erase everything except your last restore point and yet more 'free '... files cleaning

  How to use disk cleanup
  http://support.Microsoft.com/kb/310312

  You can disable hibernation if it is enabled and you do not...

  When you Hibernate your computer, Windows saves the contents of the system memory in the hiberfil.sys file. As a result, the size of the hiberfil.sys file will always be equal to the amount of physical memory in your system. If you don't use the Hibernate feature and want to reclaim the space used by Windows for the hiberfil.sys file, perform the following steps:

  -Start the Control Panel Power Options applet (go to start, settings, Control Panel, and then click Power Options).
  -Select the Hibernate tab, uncheck "Activate the hibernation", and then click OK. Although you might think otherwise, selecting never under "Hibernate" option on the power management tab does not delete the hiberfil.sys file.
  -Windows remove the "Hibernate" option on the power management tab and delete the hiberfil.sys file.

  You can control the amount of space your system restore can use...

  1. Click Start, right click my computer and then click Properties.
  2. click on the System Restore tab.
  3. highlight one of your readers (or C: If you only) and click on the button "settings".
  4 change the percentage of disk space you want to allow... I suggest moving the slider until you have about 1 GB (1024 MB or close to that...)
  5. click on OK. Then click OK again.

  You can control the amount of space used may or may not temporary Internet files...

  Empty the temporary Internet files and reduce the size, that it stores a size between 64 MB and 128 MB...

  -Open a copy of Microsoft Internet Explorer.
  -Select TOOLS - Internet Options.
  -On the general tab in the section 'Temporary Internet files', follow these steps:
  -Click on 'Delete the Cookies' (click OK)
  -Click on "Settings" and change the "amount of disk space to use: ' something between 64 MB and 128 MB. (There may be many more now.)
  -Click OK.
  -Click on 'Delete files', then select "Delete all offline content" (the box), and then click OK. (If you had a LOT, it can take 2 to 10 minutes or more).
  -Once it's done, click OK, close Internet Explorer, open Internet Explorer.

  You can use an application that scans your system for the log files and temporary files and use it to get rid of those who:

  CCleaner (free!)
  http://www.CCleaner.com/
  (just disk cleanup - do not play with the part of the registry for the moment)

  Other ways to free up space...

  SequoiaView
  http://www.win.Tue.nl/SequoiaView/

  JDiskReport
  http://www.jgoodies.com/freeware/JDiskReport/index.html

  Those who can help you discover visually where all space is used.  Then, you can determine what to do.

  After that - you want to check any physical errors and fix everything for efficient access"

  CHKDSK
  How to scan your disks for errors* will take time and a reboot.

  Defragment
  How to defragment your hard drives* will take time

  Cleaning the components of update on your Windows XP computer

  While probably not 100% necessary-, it is probably a good idea at this time to ensure that you continue to get the updates you need.  This will help you ensure that your system update is ready to do it for you.

  Download and run the MSRT tool manually:
  http://www.Microsoft.com/security/malwareremove/default.mspx
  (Ignore the details and download the tool to download and save to your desktop, run it.)

  Reset.

  Download/install the latest program Windows installation (for your operating system):
  (Windows XP 32-bit: WindowsXP-KB942288-v3 - x 86 .exe )
  (Download and save it to your desktop, run it.)

  Reset.

  and...

  Download the latest version of Windows Update (x 86) agent here:
  http://go.Microsoft.com/fwlink/?LinkId=91237
  ... and save it to the root of your C:\ drive. After you register on the root of the C:\ drive, follow these steps:

  Close all Internet Explorer Windows and other applications.

  AutoScan--> RUN and type:
  %SystemDrive%\windowsupdateagent30-x86.exe /WUFORCE
  --> Click OK.

  (If asked, select 'Run'). --> Click on NEXT--> select 'I agree' and click NEXT--> where he completed the installation, click "Finish"...

  Reset.

  Now reset your Windows with this FixIt components update (you * NOT * use the aggressive version):
  How to reset the Windows Update components?

  Reset.

  Now that your system is generally free of malicious software (assuming you have an AntiVirus application), you've cleaned the "additional applications" that could be running and picking up your precious memory and the processor, you have authorized out of valuable and makes disk space as there are no problems with the drive itself and your Windows Update components are updates and should work fine - it is only only one other thing you pouvez wish to make:

  Get and install the hardware device last drivers for your system hardware/system manufacturers support and/or download web site.

  If you want, come back and let us know a bit more information on your system - particularly the brand / model of the system, you have - and maybe someone here can guide you to the place s x of law to this end.  This isn't 100% necessary - but I'd be willing to bet that you would gain some performance and features in making this part.

• Could not load dll target ("C:\program files\backweb\backweb client\6.1.0.153\program\backweb.dll error code126)

  Original title: error code 126

  Could not load dll target ("C:\program files\backweb\backweb client\6.1.0.153\program\backweb.dll error code126)

  How can I fix it?

  Hello

  1. when exactly you get this error message?
  2. don't you make changes on the computer before this problem?

  Please answer these questions and tell us more about the issue. This could help us help you better.

  Check if the problem persists in the clean boot state.

  From your computer by using a minimal set of drivers and startup programs so that you can determine if a background program is interfering with your game or program. This type of boot is known as a "clean boot".

  Reference:

  How to configure Windows XP to start in a "clean boot" State
  http://support.Microsoft.com/kb/310353

  When you are finished troubleshooting, follow these steps to reset the computer to start as usual:
  1. click on start and then click Run.
  2. type msconfig and click OK.
  The System Configuration Utility dialog box appears.
  3. click on the tab general, click Normal Startup - load all services and device drivers and then click OK.
  4. When prompted, click on restart to restart the computer.

• Cannot install Windows updates and cannot install new programs due to Error Codes: CODE C355, Code 80070652

  Original title: C355 Codes error: CODE, Code 80070652

  I'm unable to download the updates of widows and also have problems to install new programs.  The error is in the topic above and also get a screenshot that windows installs another program that must be done first when don't want to install anything.

  Hi Whitefish50m,

  (1) what programs are you trying to install?

  (2) how long have you been faced with this problem?

  Please provide the number of up-to-date Knowledge Base that you are trying to install.

  Method 1: If a Protection of resources Windows (WRP) file is missing or is damaged, Windows may not behave as expected. Auditor of file system (CFS) scan to fix all of the corrupted system files. To do this, follow the steps mentioned in the link below:

  How to use the System File Checker tool to fix the system files missing or corrupted on Windows Vista or Windows 7

  http://support.Microsoft.com/kb/929833

  Method 2: You can follow the steps described in the article below

  Error message when you try to use Microsoft Update or Windows Update Web sites to install updates: "0x800B0100.

  http://support.Microsoft.com/kb/956702

  Method 3: You can also view the steps mentioned in the link below

  You cannot install some programs or updates

  http://support.Microsoft.com/kb/822798

  Important This section, method, or task contains steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click on the number below to view the article in the Microsoft Knowledge Base.
  How to back up and restore the registry in Windows

• Several installed programs give me error messages that they cannot work properly because I'm not the administrator

  original title: Administrator status

  Several installed programs give me error messages that they cannot work properly because I'm not the administrator.  I double checked with control panel to change my status and I AM ADMINISTRATOR. What is the problem and how to fix this?

  Several installed programs give me error messages that they cannot work properly because I'm not the administrator.  I double checked with control panel to change my status and I AM ADMINISTRATOR. What is the problem and how to fix this?

  Hey Honeybe2

  When you want to use the right click on it and run as administrator

  Walter, the time zone traveller

• Upgrade 'Stacked vs. Non-Stack Build' error-

  During the upgrade from Vista to Win7, I am stopped by an "stacked vs. non-Stack build" Error Message... which means this message - means and how to successfully upgrade to Win7?

  For all questions, installation of Windows 7, the Windows 7 Forums are the best place to ask, as they came across these errors before:

  http://social.answers.Microsoft.com/forums/en-us/w7install/threads

  "Download Windows 7 installed and activated on your PC."

  They will help you in the Windows 7 Forum at the above address.

  See you soon. Mick Murphy - Microsoft partner

• build error of createUser using the c# code sample

  I get the following build error when you use the c# code for the createUser use method example.

  I use VisualStudio2008 and the Blackberry_Admin_API - 5.0 - US.pdf c# code example.

  Build error States:

  Cannot implicitly convert type 'BESAdmin.BASemailExchangeWebService.EnableBlackBerryUserAttributesType' in 'BESAdmin.BASCoreWebService.EnableBlackBerryUserAttributesType' C:\VS2008\BESAdmin\BESAdmin\Form1.cs 76 488 BESAdmin

  The build error is on this part of the code:

  for (int j = 0; j)< attributes.enableblackberryuserattributes.length;="">

  {

  userEnableBBAttributes.enableBlackBerryUserAttributes [j] = attributes.enableBlackBerryUserAttributes [j];

  }

  Everyone has this same problem and found the solution?  It seems that there is something missing or incorrect in the sample code around type conversion between the EnableBlackberryAttributesType.

  Thank you, Ed

  Hi Ed,

  I tried throwing the code example in a project already created the mine and has not known this error at compile. The two types of objects must be the same, so I don't know why there is no conflict with assignment.

  Please try to use the sample code to create a user from the BAA API reference documents:

  http://www.BlackBerry.com/developers/docs/BAA/5.0.0/

  Or the Knowledge Base of the developer section:

  http://www.BlackBerry.com/knowledgecenterpublic/livelink.exe/fetch/2000/348583/1608023/How_To_-_Get _...

  It can also be a good idea to recreate your proxy to do this.

  Let us know if the problem is still evident with the examples above.

• chronic build error

  Since today, I get a build error in all of my projects:

  Error occurred during the build.

  Errors under builder "App descriptor Validator" of the project "MNKit".

  java.lang.NullPointerException

  Google gives no guidance on this. Restarting Momentics, or clean up projects does not help.

  At the opening of bar - descriptor.xml, I get:

  java.lang.NullPointerException
  to com.qnx.tools.bbt.core.signing.BarSignerTool. (BarSignerTool.java:105)
  to com.qnx.tools.ide.bbt.internal.core.BBTNativeSDKProvider$ BBTNativeSDKDescriptor.getBarSigner (BBTNativeSDKProvider.java:172)
  at com.qnx.tools.bbt.core.sdk.AbstractBlackBerryTabletSDKDescriptor.getValidator(AbstractBlackBerryTabletSDKDescriptor.java:122)
  at com.qnx.tools.ide.bbt.internal.core.BBTNativeSDKProvider.getValidSDKs(BBTNativeSDKProvider.java:97)
  to com.qnx.tools.bbt.core.sdk.IBlackBerryTabletSDKDescriptor$ IRegistry$ Impl.collectValidSDKs (IBlackBerryTabletSDKDescriptor.java:327)
  to com.qnx.tools.bbt.core.sdk.IBlackBerryTabletSDKDescriptor$ IRegistry$ Impl.getValidSDKs (IBlackBerryTabletSDKDescriptor.java:311)
  at com.qnx.tools.bbt.internal.core.utils.BlackberryTabletSDKUtils.getAvailableTargetPlatformVersions(BlackberryTabletSDKUtils.java:130)
  at com.qnx.tools.bbt.xml.internal.ui.editor.bbtxml.forms.GeneralAdvancedPart.getAvailablePlatformVersions(GeneralAdvancedPart.java:146)
  to com.qnx.tools.bbt.xml.internal.ui.editor.bbtxml.forms.GeneralAdvancedPart. (GeneralAdvancedPart.java:69)
  at com.qnx.tools.bbt.xml.internal.ui.editor.bbtxml.forms.GeneralPage.createLeftContent(GeneralPage.java:65)
  at com.qnx.tools.bbt.xml.internal.ui.editor.bbtxml.forms.GeneralPage.createFormContent(GeneralPage.java:54)
  at com.qnx.tools.bbt.xml.internal.ui.editor.bbtxml.forms.BBTFormPage.createFormContent(BBTFormPage.java:92)
  to org.eclipse.ui.forms.editor.FormPage$ 1.run(FormPage.java:152)
  at org.eclipse.swt.custom.BusyIndicator.showWhile(BusyIndicator.java:70)
  at org.eclipse.ui.forms.editor.FormPage.createPartControl(FormPage.java:150)
  at org.eclipse.ui.part.MultiPageEditorPart.addPage(MultiPageEditorPart.java:241)
  at org.eclipse.ui.forms.editor.FormEditor.addPage(FormEditor.java:325)
  at org.eclipse.ui.part.MultiPageEditorPart.addPage(MultiPageEditorPart.java:211)
  at org.eclipse.ui.forms.editor.FormEditor.addPage(FormEditor.java:308)
  at com.qnx.tools.bbt.xml.internal.ui.editor.bbtxml.BBTXMLEditor.addBBTPage(BBTXMLEditor.java:233)
  at com.qnx.tools.bbt.xml.internal.ui.editor.bbtxml.BBTXMLEditor.createGeneralPage(BBTXMLEditor.java:240)
  at com.qnx.tools.bbt.xml.internal.ui.editor.bbtxml.BBTXMLEditor.addPages(BBTXMLEditor.java:324)
  at org.eclipse.ui.forms.editor.FormEditor.createPages(FormEditor.java:138)
  at org.eclipse.ui.part.MultiPageEditorPart.createPartControl(MultiPageEditorPart.java:348)
  at org.eclipse.ui.internal.EditorReference.createPartHelper(EditorReference.java:670)
  at org.eclipse.ui.internal.EditorReference.createPart(EditorReference.java:465)
  at org.eclipse.ui.internal.WorkbenchPartReference.getPart(WorkbenchPartReference.java:595)
  at org.eclipse.ui.internal.EditorReference.getEditor(EditorReference.java:289)
  at org.eclipse.ui.internal.WorkbenchPage.busyOpenEditorBatched(WorkbenchPage.java:2945)
  at org.eclipse.ui.internal.WorkbenchPage.busyOpenEditor(WorkbenchPage.java:2850)
  to org.eclipse.ui.internal.WorkbenchPage.access$ 11 (WorkbenchPage.java:2842)
  to org.eclipse.ui.internal.WorkbenchPage$ 10.run(WorkbenchPage.java:2793)
  at org.eclipse.swt.custom.BusyIndicator.showWhile(BusyIndicator.java:70)
  at org.eclipse.ui.internal.WorkbenchPage.openEditor(WorkbenchPage.java:2789)
  at org.eclipse.ui.internal.WorkbenchPage.openEditor(WorkbenchPage.java:2773)
  at org.eclipse.ui.internal.WorkbenchPage.openEditor(WorkbenchPage.java:2764)
  at org.eclipse.ui.ide.IDE.openEditor(IDE.java:651)
  at org.eclipse.ui.ide.IDE.openEditor(IDE.java:610)
  at org.eclipse.ui.actions.OpenFileAction.openFile(OpenFileAction.java:99)
  at org.eclipse.ui.actions.OpenSystemEditorAction.run(OpenSystemEditorAction.java:99)
  at org.eclipse.ui.actions.RetargetAction.run(RetargetAction.java:221)
  to org.eclipse.ui.navigator.CommonNavigatorManager$ 3.open(CommonNavigatorManager.java:185)
  to org.eclipse.ui.OpenAndLinkWithEditorHelper$ InternalListener.open (OpenAndLinkWithEditorHelper.java:48)
  to org.eclipse.jface.viewers.StructuredViewer$ 2.run(StructuredViewer.java:866)
  at org.eclipse.core.runtime.SafeRunner.run(SafeRunner.java:42)
  to org.eclipse.ui.internal.JFaceUtil$ 1.run(JFaceUtil.java:49)
  at org.eclipse.jface.util.SafeRunnable.run(SafeRunnable.java:175)
  at org.eclipse.jface.viewers.StructuredViewer.fireOpen(StructuredViewer.java:864)
  at org.eclipse.jface.viewers.StructuredViewer.handleOpen(StructuredViewer.java:1152)
  at org.eclipse.ui.navigator.CommonViewer.handleOpen(CommonViewer.java:462)
  to org.eclipse.jface.viewers.StructuredViewer$ 6.handleOpen(StructuredViewer.java:1256)
  at org.eclipse.jface.util.OpenStrategy.fireOpenEvent(OpenStrategy.java:275)
  to org.eclipse.jface.util.OpenStrategy.access$ 2 (OpenStrategy.java:269)
  to org.eclipse.jface.util.OpenStrategy$ 1.handleEvent(OpenStrategy.java:309)
  at org.eclipse.swt.widgets.EventTable.sendEvent(EventTable.java:84)
  at org.eclipse.swt.widgets.Display.sendEvent(Display.java:4128)
  at org.eclipse.swt.widgets.Widget.sendEvent(Widget.java:1457)
  at org.eclipse.swt.widgets.Widget.sendEvent(Widget.java:1480)
  at org.eclipse.swt.widgets.Widget.sendEvent(Widget.java:1465)
  at org.eclipse.swt.widgets.Widget.notifyListeners(Widget.java:1270)
  at org.eclipse.swt.widgets.Display.runDeferredEvents(Display.java:3974)
  at org.eclipse.swt.widgets.Display.readAndDispatch(Display.java:3613)
  at org.eclipse.ui.internal.Workbench.runEventLoop(Workbench.java:2701)
  at org.eclipse.ui.internal.Workbench.runUI(Workbench.java:2665)
  to org.eclipse.ui.internal.Workbench.access$ 4 (Workbench.java:2499)
  to org.eclipse.ui.internal.Workbench$ 7.run(Workbench.java:679)
  at org.eclipse.core.databinding.observable.Realm.runWithDefault(Realm.java:332)
  at org.eclipse.ui.internal.Workbench.createAndRunWorkbench(Workbench.java:668)
  at org.eclipse.ui.PlatformUI.createAndRunWorkbench(PlatformUI.java:149)
  at org.eclipse.ui.internal.ide.application.IDEApplication.start(IDEApplication.java:123)
  at org.eclipse.equinox.internal.app.EclipseAppHandle.run(EclipseAppHandle.java:196)
  at org.eclipse.core.runtime.internal.adaptor.EclipseAppLauncher.runApplication(EclipseAppLauncher.java:110)
  at org.eclipse.core.runtime.internal.adaptor.EclipseAppLauncher.start(EclipseAppLauncher.java:79)
  at org.eclipse.core.runtime.adaptor.EclipseStarter.run(EclipseStarter.java:344)
  at org.eclipse.core.runtime.adaptor.EclipseStarter.run(EclipseStarter.java:179)
  at sun.reflect.NativeMethodAccessorImpl.invoke0 (Native Method)
  at sun.reflect.NativeMethodAccessorImpl.invoke(NativeMethodAccessorImpl.java:39)
  at sun.reflect.DelegatingMethodAccessorImpl.invoke(DelegatingMethodAccessorImpl.java:25)
  at java.lang.reflect.Method.invoke(Method.java:597)
  at org.eclipse.equinox.launcher.Main.invokeFramework(Main.java:622)
  at org.eclipse.equinox.launcher.Main.basicRun(Main.java:577)
  at org.eclipse.equinox.launcher.Main.run(Main.java:1410)

  I am running on a Mac with the new Oracle Java 1.6.0.37 Mountain Lion.

  solved.

  Re-install Momentics and the simutaor is done.

• Build error on request requestExit

  I encountered a strange problem to call the requestExit API. Compiles normal but generation has an error.

  undefined reference to the symbol "_ZN2bb11Application11requestExitEv".

  Note: '_ZN2bb11Application11requestExitEv' is defined in DSO C:/bbndk/target_10_0_9_2318/qnx6/armle-v7/usr/lib/libbb.so.1 try so add to the linker command line

  could not read symbols: invalid operation

  My source code is as below

  Cpp:
  
  MyApplication::MyApplication(bb::cascades::Application *app)
  : app(app)
  
  app->requestExit(); //Application::instance()->requestExit(); build error also
  
  bar-descriptor.xml
  
  
  .pro
  LIBS += -lbbsystem -lbbnetwork -lbbplatform -lscreen -lbbdata -lbbdevice
  

  Which library else I would add to my project?  Thanks for letting me out.

  Hello

  libbb.so East - lbb

• I use windows 7 64-bit edition Home premium and I cannot connect to access database in java program.it shows error database connection driver not installed.

  I am using windows 7 64 bit home premium I installed ms office 2007 and did all the settings.
  but I am unable to connect to the Access database in java program.it shows error database connection driver not installed.
  Please give me the solution...

  Hello

  I suggest you to ask your question about Java programming forums on the subject.

  https://forums.Oracle.com/Forums/Forum.jspa?forumid=922

  You can also ask your question on the forums to access.

  http://answers.Microsoft.com/en-us/Office/forum/access?page=1&tab=all&TM=1349633636662

• An unexpected build error has occurred: index was outside the bounds of the array

  Hello

  I use OPA version 12.1.1 (November 2015 edition of cloud).

  When I try to debug my OPA project I get this error:

  "An unexpected build error has occurred: index was outside the bounds of the array.

  Does anyone of you understand what that means?

  Kind regards

  Xavier M.

  What language / region is your project?

  You are able to apply for service with the support of Oracle?  This error usually requires the investigation of the project to determine the root cause.