Protect the DHCP with SRM
Hey guys,.
We are in the middle of a project of DR and have come to the point that we want to have our service ready DHCP DR. The idea of Split range (80/20) standard is an option we are looking at, but in a DR or even single server failure there is a bit of management that is necessary to ensure the secondary DHCP server can serve all the IP addresses of all scopes (before it's 20% fills). So we have an idea to use SRM to protect DHCP.
We have two sites, connected via the 3 layer, with two 10GB connections between the two (for fault tolerance and load balancing). The DR site is a live environment; It is a branch across the city (such as 30 kilometers).
The idea of the scope of Split we have DHCP running on a domain controller in each site with the server DHCP secondary (DR) serving 20% of the IP addresses of each field and the primary DHCP serving 80%. This can be setup using the wizard of scope of Split that MS has the Server 2008. In doing so we cover failure of the primary DHCP server (it is also a virtual machine so HA protects too), but also the Site as the secondary DHCP server failure will be in place. If we have an extended outage of the primary DHCP server then we need to get to the secondary DHCP server and increase all scopes, ensuring that conflict detection is on.
Our thinking is to move the DHCP on the domain controller and give it its own virtual server. Then, we protect the service DHCP using MRS to move it on the DR site in a DR situation. This will cause the DHCP server to get a new IP address, as the two sites are connected by Layer 3 - the same subnets cannot exist in both places. And that's where our thought process is getting confused...
What will happen with the DHCP service, if the server has a new IP address?
What is the process for DHCP clients attempting to renew its IP address:
one) to restart the computer?
(b) to the mark 1/2 way of their lease?
On the one hand, I think that MRS is the easiest way to protect not only the DHCP, but also to minimize the DHCP solution management. The scope of Split idea help to ensure that any change to a DHCP server is replicated to the other server: scope changes, scope of options changes, reservation changes, etc...
Has anyone analyzed the all around it?
Thank you!!
Gerald
That is right. DHCP server only cares about its own address. As long as you subnet broadcast forwarders to two IP addresses of the DHCP server so that the request hits the server DHCP it matches just MAC address for reservations of IP / scopes etc. and will work.
Only thing to check when it rises to the DR is if the DHCP server may need approval again before DHCP works. Do not remember how it works off the coast of the hand.
Tags: VMware
Similar Questions
-
Commissioning of the size of the lun with SRM
Hi guys I have a question in mind. While this is resolved in the latest version of vsphere 5.x to present more than 2 TB lun.
the installer, is that I have a virtual machine with 2 TB VMDK for drive D, and 1 TB VMDK for drive E.
If extended two 2 x 2 TB total lun lun 4 TB in the main site using the storage replication and srm for automation.
is it automatically adapt the extension of lun I do elementary when I do fail over the site of DR?
To what extent are you referring?
Extensions of VMFS - are they bad, or just simply misunderstood? VMware vSphere Blog - VMware Blogs
Be careful if you use extended MIS program, make sure that your storage space supports the Group of concordance.
See the guide below:
Documentation Centre Site Recovery Manager 5.5 - How MRS. calculates Datastore groups
The recovering site know the multiple measurement data by storage of consistency group store.
-
Password protect the Structure/form Code
Hello
I'm looking for a way to password protect the structure of a form code, but leave any open/no secure is to say fill, print, emailing, etc. Is it possible to do it with these versions of the applications that someone found?
Adobe Acro Pro X 10.1.6
Adobe Livecycle designer ES2 9.0
I don't want the user to see the protection when the form is opened in the reader. I just want to see the protection or password message box if someone were to open the PDF in Livecycle Designer.
I tried the password protecting the form with LC and then extend the rights but it always take off password protection when I do that. So first I add protection in LC, then I save the PDF file and then I open the PDF in Acro Pro X and extend the rights.
If anyone has faced this, I would appreciate some suggestions. Is there a way to code in the open event, perhaps to check the environment?
Yes, you can add a password to a doc that will only be visible when you open it in LiveCycle designer and not when a user opens the file in Reader/Acrobat.
You also need well Acrobat AND LiveCycle designer.
You are doing your dev in the designer, then you add security in Acrobat.
In acrobat
Advanced > Security > encrypt with password
Then under authorization, check box restrict editing, provide a password, and check the brand of what you can allow/disallow.
Click OK.
A 2nd dialog box will ask you to re-enter your password.
Subsequently, you must save the file and you will notice that the title bar now (secure)
-
Clarification on the protection of the VMS with snapshots. SRM 5.1
In SRM 5.1 documentation one of the limitations listed is:
When the protection of the VMS with snapshots of the memory state, the ESXi hosts on protection and restoration sites must have compatible processors as defined in the articles of the VMware knowledge base CPU VMotion for Intel processors compatibility requirements and CPU VMotion for AMD compatibility requirements. Guests must also have the same characteristics of active BIOS. If the BIOS of the server configurations do not match, they show a compatibility error message, even if otherwise, they are identical. The two most common to check features are the No-Execute memory Protection (NX / XD) and virtualization technology (VT / AMD - V).
You can work around this limitation by using the mode of the VCA on groups the and protected?
VCA mode will mitigate this risk, but you must make sure that the two Clusters to the protégé and recovery Sites are at the SAME level CVS before take snapshots of the memory.
At the end of the day, only a "planned actual Migration" will verify this.
Good luck!
-
How to protect the old tickets in the iphone 5 with ios 9.3?
I managed to password protect the new notes in my Iphone but how to protect notes taken before also in my Iphone?
You can only the password protects the new notes. I suggest 'Copy and paste' transfer of old notes in a new note, and then delete the old note. May take some time according to note how much you have, but it will work.
Note that you can not protect note also with PDFs, audio, video, etc. show in this article.
-
I have a HP DV7-4165 which has Windows 7 64 bit and simple features of the HP pass identity protection using the drive with the tips of the fingers. My Firefox support says "If you have the Firefox browser on your computer when your HP SimplePass Identity Protection software is installed, a Firefox extension will also be installed which enables support for the use of the fingerprints with the browser Firefox." Once I updated to Firefox 4 it no longer works.
You can get Firefox 3.6.16 here:
http://www.Mozilla.com/en-us/Firefox/all-older.html -
Hello
I have a service online Internet with 5 public IP addresses.
The router and the AP are connected to a switch.
I would like to set up a WRT54G Router with a public IP address and use DHCP (with private ip address) for the computers that will connect to the AP.
That the AP is connected to the switch, it is possible that the other wired computers that are connected to the same switch can get an IP from the DHCP?
Thanks in advance
In this case, the routing is automatic.
WRT54G configuration:
WAN:
Internet connection: static IP address
IP address: 180.X. X 170
Subnet mask: 255.255.255.248
Gateway: 180.x.x.x (Ex: 180.x.x.1)
DNS: servers your ISP DNS
LAN:
The IP address of the router: 10.10.10.1
DHCP range: 10.10.10.100 of-online 10.10.10.200
-
Protect the Q10 blackBerry with Blackberry problems
Hello Blackberry community,
Recently, I've had my Blackberry "BOLD" stolen so I said 'no problem, Blackberry protect will take care of all my stuff. "Sound in the cloud." But today, when I got the blackberry protect recovery in my brand new Q10 I realized that I don't have that 31 contact now! Almost all my contacts are GONE! Anyone know what could have happened with the rest of my contacts? I do not understand how the Blackberry protect weekly backups I had put up only ended up saving a small part of my contact list. According to the Blacberry protect the site, the last backup was August 5, 2014. My cell phone was stolen on 12 August, the backup should be updated. But it's not. Is there a problem with Blackberry protect migrate Blackberry 7-10 of Blackberry? No indication as to what is happening with my contacts is greatly appreciated.Concerning
Hello there, 31 contacts most likely are from a very old backup, and all your contacts are now synchronized wirelessly with your email. Which is why you don't have them in a BlackBerry protects back upward.
Haven't you set up your email yet? What are the prospects it, Gmail? -
Problem with the DHCP server IP address
Hello
a new installation of LAN, two VSS pair core 6509, 15 closets, with piles of 3750. Floor 15 only, host devices can ping the DHCP server, but cannot acquire IP addresses. not this problem on other floors?
PortFast a dother settings are intact.
your thoughts with be appreciated.
Massoud
Are the trunks will switches closets for the vlan, the DHCP server is in?
Sent by Cisco Support technique iPhone App
-
Having the problem with the function on SG300 Dhcp / 500?
Having the problem with the function on SG300 Dhcp / 500? now I can use the dhcp server on the two model, but have a problem.
My problem is when I create
VLAN 1: 192.168.0.1/24 dhcp pool 192.168.0.10 - 250
VLAN 10: 192.168.10.10 - 250 192.168.10.1/24 dhcp pool
case 1
I plug the pc to vlan 1 can I get ip 192.168.0.11. But when I change this pc to a new port in vlan 2 I always get the same ip address. why I can not get IP of vlan2.
case 1
I plug the pc to vlan 2 I can get ip 192.168.10.11. But when I change this pc to a new port in the vlan 1 I always get the same ip address. why I can not get IP of vlan1.
but when I have access to the switch and remove the link after that that i will get correct IP.
I think this is the bug of this firmware. Could you help this case.
This is a known bug that is the setting of Cisco
Sent by Cisco Support technique iPad App
-
protection tunnels works with the mode of transport only?
Anyone know why protection tunnel works with the mode of transport only? If I change to tunnel mode, it stops working immediately.
Thank you
That's because Tunnel mode creates a new IP header that is modified when is coordinated, when the remote peer receives this new header which is concerned the Security numbers do not match what it generated. Using transport mode retains the original header and only encapsulates the payload.
-
Remote access VPN with ASA 5510 by using the DHCP server
Hello
Can someone please share your knowledge to help me find out why I'm not able to receive an IP address on the remote access VPN connection so that I can get an IP local pool DHCP?
I'm trying to set up remote access VPN with ASA 5510. It works with dhcp local pool but does not seem to work when I tried to use an existing DHCP server. It is tested in an internal network as follows:
!
ASA Version 8.2 (5)
!
interface Ethernet0/1
nameif inside
security-level 100
IP 10.6.0.12 255.255.254.0
!
IP local pool testpool 10.6.240.150 - 10.6.240.159 a mask of 255.255.248.0. (worked with it)
!
Route inside 0.0.0.0 0.0.0.0 10.6.0.1 1
!
Crypto ipsec transform-set esp-3des esp-md5-hmac FirstSet
life crypto ipsec security association seconds 28800
Crypto ipsec kilobytes of life - safety 4608000 association
Crypto-map dynamic dyn1 1jeu transform-set FirstSet
dynamic mymap 1 dyn1 ipsec-isakmp crypto map
mymap map crypto inside interface
crypto ISAKMP allow inside
crypto ISAKMP policy 1
preshared authentication
3des encryption
sha hash
Group 2
life 43200
!
VPN-addr-assign aaa
VPN-addr-assign dhcp
!
internal group testgroup strategy
testgroup group policy attributes
DHCP-network-scope 10.6.192.1
enable IPSec-udp
IPSec-udp-port 10000
!
username testlay password * encrypted
!
tunnel-group testgroup type remote access
tunnel-group testgroup General attributes
strategy-group-by default testgroup
DHCP-server 10.6.20.3
testgroup group tunnel ipsec-attributes
pre-shared key *.
!
I got following output when I test connect to the ASA with Cisco VPN client 5.0
Jan 16 15:39:21 [IKEv1]: IP = 10.15.200.108, IKE_DECODE RECEIPT Message (msgid = 0) with payloads: (4) SA (1) + KE + NUNCIO (10) + ID (5), HDR + VENDO
4024 bytesR copied in 3,41 0 seconds (1341 by(tes/sec) 13) of the SELLER (13) seller (13) + the SELLER (13), as well as the SELLER (13) ++ (0) NONE total length: 853
Jan 16 15:39:21 [IKEv1 DEBUG]: IP = 10.15.200.108, SA payload processing
Jan 16 15:39:21 [IKEv1 DEBUG]: IP = 10.15.200.108, processing ke payload
Jan 16 15:39:21 [IKEv1 DEBUG]: IP = 10.15.200.108, payload processing ISA_KE
Jan 16 15:39:21 [IKEv1 DEBUG]: IP = 10.15.200.108, nonce payload processing
Jan 16 15:39:21 [IKEv1 DEBUG]: IP = 10.15.200.108, payload processing ID
Jan 16 15:39:21 [IKEv1 DEBUG]: IP = 10.15.200.108, payload processing VID
Jan 16 15:39:21 [IKEv1 DEBUG]: IP = 10.15.200.108, received xauth V6 VID
Jan 16 15:39:21 [IKEv1 DEBUG]: IP = 10.15.200.108, payload processing VID
Jan 16 15:39:21 [IKEv1 DEBUG]: IP = 10.15.200.108, DPD received VID
Jan 16 15:39:21 [IKEv1 DEBUG]: IP = 10.15.200.108, payload processing VID
Jan 16 15:39:21 [IKEv1 DEBUG]: IP = 10.15.200.108, received Fragmentation VID
Jan 16 15:39:21 [IKEv1 DEBUG]: IP = 10.15.200.108, IKE Peer included IKE fragmentation capability flags: Main Mode: real aggressive Mode: false
Jan 16 15:39:21 [IKEv1 DEBUG]: IP = 10.15.200.108, payload processing VID
Jan 16 15:39:21 [IKEv1 DEBUG]: IP = 10.15.200.108, received NAT-Traversal worm 02 VID
Jan 16 15:39:21 [IKEv1 DEBUG]: IP = 10.15.200.108, payload processing VID
Jan 16 15:39:21 [IKEv1 DEBUG]: IP = 10.15.200.108, the customer has received Cisco Unity VID
Jan 16 15:39:21 [IKEv1]: IP = 10.15.200.108, connection landed on tunnel_group testgroup
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, IKE SA payload processing
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, IKE SA proposal # 1, turn # 9 entry overall IKE acceptable matches # 1
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, build the payloads of ISAKMP security
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, building ke payload
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, building nonce payload
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, Generating keys for answering machine...
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, construction of payload ID
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, build payloads of hash
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, calculation of hash for ISAKMP
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, build payloads of Cisco Unity VID
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, constructing payload V6 VID xauth
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, building dpd vid payload
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, constructing the payload of the NAT-Traversal VID ver 02
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, NAT-discovery payload construction
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, calculation of hash discovered NAT
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, NAT-discovery payload construction
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, calculation of hash discovered NAT
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, construction of Fragmentation VID + load useful functionality
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, build payloads VID
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, send Altiga/Cisco VPN3000/Cisco ASA GW VID
Jan 16 15:39:21 [IKEv1]: IP = 10.15.200.108, IKE_DECODE SEND Message (msgid = 0) with payloads: HDR SA (1) KE (4) NUNCIO (10) + ID (5) + HASH (8) + SELLER (13) + the SELLER (13) + the SELLER (13) + the SELLER (13) NAT - D (130) + NAT - D (130) of the SELLER (13) + the seller (13) + NONE (0) total length: 440
Jan 16 15:39:21 [IKEv1]: IP = 10.15.200.108, IKE_DECODE RECEIPT Message (msgid = 0) with payloads: HDR + HASH (8) + NOTIFY (11) + NAT - D (130) + NAT - D (130) of the SELLER (13) + the seller (13) + NONE (0) overall length: 168
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, processing hash payload
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, calculation of hash for ISAKMP
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, processing notify payload
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, payload NAT-discovery of treatment
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, calculation of hash discovered NAT
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, payload NAT-discovery of treatment
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, calculation of hash discovered NAT
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, payload processing VID
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, useful treatment IOS/PIX Vendor ID (version: 1.0.0 capabilities: 00000408)
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, payload processing VID
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, the customer has received Cisco Unity VID
Jan 16 15:39:21 [IKEv1]: Group = testgroup, I
[OK]
KenS-mgmt-012 # P = 10.15.200.108, status of automatic NAT detection: remote end is NOT behind a NAT device this end is NOT behind a NAT device
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, empty building hash payload
Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, build payloads of hash qm
Jan 16 15:39:21 [IKEv1]: IP = 10.15.200.108, IKE_DECODE SEND Message (msgid = d4ca48e4) with payloads: HDR + HASH (8) + ATTR (14) + (0) NONE total length: 72
Jan 16 15:39:26 [IKEv1]: IP = 10.15.200.108, IKE_DECODE RECEIPT Message (msgid = d4ca48e4) with payloads: HDR + HASH (8) + ATTR (14) + (0) NONE total length: 87
Jan 16 15:39:26 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, process_attr(): enter!
Jan 16 15:39:26 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, transformation MODE_CFG response attributes.
Jan 16 15:39:26 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, IKEGetUserAttributes: primary DNS = authorized
Jan 16 15:39:26 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, IKEGetUserAttributes: secondary DNS = authorized
Jan 16 15:39:26 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, IKEGetUserAttributes: = authorized primary WINS
Jan 16 15:39:26 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, IKEGetUserAttributes: = authorized secondary WINS
Jan 16 15:39:26 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, IKEGetUserAttributes: Compression IP = disabled
Jan 16 15:39:26 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, IKEGetUserAttributes: Split Tunneling political = disabled
Jan 16 15:39:26 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, IKEGetUserAttributes: setting Proxy browser = no - modify
Jan 16 15:39:26 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, IKEGetUserAttributes: browser Local Proxy bypass = disable
Jan 16 15:39:26 [IKEv1]: Group = testgroup, Username = testlay, IP = 10.15.200.108, (testlay) the authenticated user.
Jan 16 15:39:26 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, empty building hash payload
Jan 16 15:39:26 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, build payloads of hash qm
Jan 16 15:39:26 [IKEv1]: IP = 10.15.200.108, IKE_DECODE SEND Message (msgid = 6b1b471) with payloads: HDR + HASH (8) + ATTR (14) + (0) NONE total length: 64
Jan 16 15:39:26 [IKEv1]: IP = 10.15.200.108, IKE_DECODE RECEIPT Message (msgid = 6b1b471) with payloads: HDR + HASH (8) + ATTR (14) + NONE (0) overall length: 60
Jan 16 15:39:26 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, process_attr(): enter!
Jan 16 15:39:26 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, cfg ACK processing attributes
Jan 16 15:39:27 [IKEv1]: IP = 10.15.200.108, IKE_DECODE RECEIPT Message (msgid = 49ae1bb8) with payloads: HDR + HASH (8) + ATTR (14) + (0) NONE total length: 182
Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, process_attr(): enter!
Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, treatment cfg request attributes
Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: application received for the IPV4 address!
Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: application received for the IPV4 network mask!
Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: application received for DNS server address.
Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: application received for the address of the WINS server.
Jan 16 15:39:27 [IKEv1]: Group = testgroup, Username = testlay, IP = 10.15.200.108, transaction mode attribute unhandled received: 5
Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: application received for the banner!
Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: application received for setting save PW!
Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: receipt of request for default domain name!
Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: application received for Split-Tunnel list!
Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: application received for split DNS!
Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: application received for PFS setting!
Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: application received for the Proxy Client browser setting!
Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: application received for the list of backup peer ip - sec!
Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: application received for setting disconnect from the Client Smartcard Removal!
Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: application received for the Version of the Application.
Jan 16 15:39:27 [IKEv1]: Group = testgroup, Username = testlay, IP = 10.15.200.108, Type of Client: Windows NT Client Application Version: 5.0.07.0440
Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: application received for FWTYPE!
Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: request received for the DHCP for DDNS hostname is: DEC20128!
Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: application received for the UDP Port!
Jan 16 15:39:32 [IKEv1]: Group = testgroup, Username = testlay, IP = 10.15.200.108, in double Phase 2 detected packets. No last packet retransmit.
Jan 16 15:39:37 [IKEv1]: IP = 10.15.200.108, IKE_DECODE RECEIPT Message (msgid = b04e830f) with payloads: HDR + HASH (8) + NOTIFY (11) + (0) NONE total length: 84
Jan 16 15:39:37 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, processing hash payload
Jan 16 15:39:37 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, processing notify payload
Jan 16 15:39:37 [IKEv1]: Group = testgroup, Username = testlay, IP = 10.15.200.108, in double Phase 2 detected packets. No last packet retransmit.
Jan 16 15:39:39 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, IKE has received the response from type [] at the request of the utility of IP address
Jan 16 15:39:39 [IKEv1]: Group = testgroup, Username = testlay, IP = 10.15.200.108, cannot get an IP address for the remote peer
Jan 16 15:39:39 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, case of mistaken IKE TM V6 WSF (struct & 0xd8030048)
, : TM_DONE, EV_ERROR--> TM_BLD_REPLY, EV_IP_FAIL--> TM_BLD_REPLY NullEvent--> TM_BLD_REPLY, EV_GET_IP--> TM_BLD_REPLY, EV_NEED_IP--> TM_WAIT_REQ, EV_PROC_MSG--> TM_WAIT_REQ, EV_HASH_OK--> TM_WAIT_REQ, NullEvent Jan 16 15:39:39 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, case of mistaken IKE AM Responder WSF (struct & 0xd82b6740)
, : AM_DONE, EV_ERROR--> AM_TM_INIT_MODECFG_V6H, EV_TM_FAIL--> AM_TM_INIT_MODECFG_V6H NullEvent--> AM_TM_INIT_MODECFG, EV_WAIT--> AM_TM_INIT_XAUTH_V6H, EV_CHECK_QM_MSG--> AM_TM_INIT_XAUTH_V6H, EV_TM_XAUTH_OK--> AM_TM_INIT_XAUTH_V6H NullEvent--> AM_TM_INIT_XAUTH_V6H, EV_ACTIVATE_NEW_SA Jan 16 15:39:39 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, IKE SA AM:bd3a9a4b ending: 0x0945c001, refcnt flags 0, tuncnt 0
Jan 16 15:39:39 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, sending clear/delete with the message of reason
Jan 16 15:39:39 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, empty building hash payload
Jan 16 15:39:39 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, constructing the payload to delete IKE
Jan 16 15:39:39 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, build payloads of hash qm
Jan 16 15:39:39 [IKEv1]: IP = 10.15.200.108, IKE_DECODE SEND Message (msgid = 9de30522) with payloads: HDR HASH (8) + DELETE (12) + (0) NONE total length: 80
Kind regards
Lay
For the RADIUS, you need a definition of server-aaa:
Protocol AAA - NPS RADIUS server RADIUS
AAA-server RADIUS NPS (inside) host 10.10.18.12
key *.
authentication port 1812
accounting-port 1813
and tell your tunnel-group for this server:
General-attributes of VPN Tunnel-group
Group-NPS LOCAL RADIUS authentication server
--
Don't stop once you have upgraded your network! Improve the world by lending money to low-income workers:
http://www.Kiva.org/invitedBy/karsteni -
Replicate the VMS with FTP and VM with virtual disk shared by: SRM with vSphre replication
I have a VM and FT is configured on it. Now I can reproduce the virtual machine with SRM with replication of vSphere. I have not configured array based replication. Similarly, I have two DB VMs cluster, but they share a virtual disk between them. Can I replicate these VMs DB with vSphere replication?
Your valuable contribution is much appreciated.
I got the answer, for the virtual machine with FT and shared virtual disk replication, to do SRM with array based replication. vSphere replication cannot replicate virtual machine with FT or shared disk.
-
ADF Mobile access protected web service with the user name and password
With Jdev 11.1.2.4 (with the extension of the ADF Mobile) I am creating a data control that uses a SOAP web service. The web service is not protected by a policy of wss, but its point of endpoint URL is only protected by simple HTTP authentication (internal weblogic server is not accessible public.) We use an Apache server that is configured with a location that is a simple proxypass on url of the web service endpoint weblogic. This apache location apply simple HTTP authorization). I can invoke successfully the methods with parser HTTP by simply adding to the request HTTP header "authorization: xxxxxxxxxxxxxxxxxx base =" (where xxx = user name and encrypted password).
In the mobile application of ADF, I used the DataControls.dcx-> window to connect to the Web Service change and provided the username and password to the URL of the endpoint. The problem is that after the deployment and execution of this application on the emulator (or the device itself), I get no data by the web service since with the HTTP 401 error http server responses. It seems that that the credentials are not deployed to the device, so while the application is running can not find them.
I searched a lot and found a similar article (quite old) in the RTO by Frank Nimphius here access_protected_web_services_from_adf.htm
Is there a way to do this, or if I'm missing the entire image?
Thank you very much.
Christos
Check out blog Shay https://blogs.oracle.com/shay/entry/accessing_secure_web_services_from
or Andrejus http://andrejusb.blogspot.de/2012/11/adf-mobile-secured-web-service-access.html
Timo
-
Storage VMotion in LUN protected with SRM
Hello
I don't have RS in my environment and do not know what will happen in the next version of SRM (Version 1.5), but I'm caurios to know the answer to this question.
Now that vSphere officially supports Storage VMotion, is it supported in SRM as well? Which means that if you have two LUNS protected by SRM in a DataCenter. What happens if use you Storage VMotion LUN to one another. (Both protected)
Move the files in your DR Site as well? No need to reproduce on the internet?
Thank you
Currently, if you a data store SVMotion not replicated to replicated store listed in MRS. VM pop-ups in the Protection Group - like 'not protected' as a whole new VM. You can then right-click and choose to protect...
It is less smooth vice versa - it is as "not configured" and you need to delete manually the list of SRM...
My free guide to SRM - covers this 179 page...
Concerning
Mike Landry
RTFM education
Author of the book of MRS: http://www.lulu.com/content/4343147
Maybe you are looking for
-
iMessages - out of 'Available' on 'Offline '.
In iMessages > Preferences I think I chose to stay as being available at all times, open the application start upward, toward the top of the icon in the menu BUT when I go out iMessage to go to the post office or elsewhere to check, it says that my s
-
Black flashing/scrapie browser on Web sites.
If the thing is, the whole page is flashing black, as you can see in the screenshot. And when it's dark, if I hit f11 or I change the tab and go right, correct, but I don't see things like the home in facebook for example button. Or the facebook chat
-
Is it possible to transfer a conversation iMessage from my iPhone to my Mac?
Hi all... I was wondering if someone could help me with the problem of having an iMessage conversation dating back months my phone is off and as a result of my Macbook. My iPhone is running iOS 9.3.3 and my Macbook is running 10.7.5. It would be g
-
I accidentally deleted my entire search engine bar in the toolbar. Please help me to get it back.
I accidentally deleted my entire search engine bar in the toolbar. I can't find how to get it back. Can someone help me? Thank you
-
Hi all I lost my manual book and I have a problem to find the what is the maximum can RAM that my HP for computer laptop-15-AY012DX is going up? Your help is appreciated. Thank you and best regards.