protection of the system only records a week

Similar Questions

• Protection of the system. Responding file or directory is not a reparse point: (0 X 80071126) if please close the property page and try again.

  Three weeks ago, I got a problem of compatibility with nero premium 7 that I installed it, so I had to remove my laptop with great difficulty! I tried restoring the system by removing, and it failed. Whenever I open the system restore, I get a message... "There was an unexpected error in the property page. "The file or directory is not a reparse point: (0 X 80071126) if please close the property page and try again. For the protection of the system disks can not be re-analyzed for the same reason.
  What is the problem and how can I solve it? System repair not even managed to solve!

  Hello
   
  We will first check if the system restore services are set to automatic and started. To do this, follow these steps.
  1. Click Start, type services.msc and press to enter.
  2. from the list of services, double-click Windows backup and Volume shadow copy services.
  3. in the Properties window, select the automatic startup type and click Start.
  4. apply the changes.
  5. try to open the system restore and check the result.
   
  If the problem continues, check if the system of protection is disabled. To do this, follow these steps.
  1. Click Start, right-click computer and click Properties.
  2. click on Protection of the system under tasks.
  3. on the System Protection tab, be sure to place a check mark under all available disks to enable system restore or to market.
  4. apply the settings and check the result.
   
  For more information, see this link: http://windows.microsoft.com/en-us/windows-vista/System-Restore-frequently-asked-questions
   
  I hope this helps.

  Kind regards
  Syed
  Answers from Microsoft supports the engineer.
  Visit our Microsoft answers feedback Forum and let us know what you think.

• On the Protection of the system in Windows 8!

  Hello

  My question is in the protection of the system in Windows 8, I have C and D lit discs! And when you turn on the drive C drive D is also on both at the same time! These drives supposed to be because I was still able to do the restore of the system both off!

  Thank you very much for your help,

  HONEY BEAR 100

  Yes, drive C and drive D are always when the computer is turned on. Drive C is your main drive and D drive is often used by the CD/DVD drive in your computer. The only way to 'turn off' the D drive is by disconnecting the data cable and the power cable on the CD/DVD drive. I have no experience with the system restore.

• How to create a restore point in the protection of the system in safe mode?

  As topic the question, how to create a restore point in the protection of the system in safe mode?

  Hello

  read a tutorial on the below link for everything you need to know about the system restore

  http://www.bleepingcomputer.com/tutorials/tutorial143.html

  and read this too

  System Restore: frequently asked questions

  http://Windows.Microsoft.com/en-us/Windows-Vista/system-restore-frequently-asked-questions

• Get the error when you try to manually create a restore point in Vista 32 - Bit - System - Protection of the system control panel. Got the unable to create the specified task

  Get the error when you try to manually create a restore point in Vista 32 - Bit - System - Protection of the system control panel.
  Got the unable to create the specified task

  Hello

  What is the exact error message received when the problem occurs?

  Methood 1:

  Auditor of file system (CFS) scan to fix all of the corrupted system files. To do this, follow the steps in the following link:

  How to use the System File Checker tool to fix the system files missing or corrupted on Windows Vista or Windows 7

  http://support.Microsoft.com/kb/929833 

  Method 2:

  You can start Windows Vista by using a minimal set of drivers and startup programs. This type of boot is known as a "clean boot". A clean boot helps eliminate software conflicts.

  I suggest to put the computer in a clean boot state, and check if the problem persists, see the link:
  How to troubleshoot a problem by performing a clean boot in Windows Vista or in Windows 7
  http://support.Microsoft.com/kb/929135
  Note: See step 7; Reset the computer to start as usual after troubleshooting is performed.

  Method 3:

  You can temporarily disable the security software and check if the problem occurs. Check out the following link to do the same thing:

  http://Windows.Microsoft.com/en-GB/Windows-Vista/disable-antivirus-software

  Warning: Antivirus software can help protect your computer against viruses and other security threats. In most cases, you should not disable your antivirus software. If you need to disable temporarily to install other software, you must reactivate as soon as you are finished. If you are connected to the Internet or a network, while your antivirus software is disabled, your computer is vulnerable to attacks.

  I hope this helps! Let us know if you need more assistance.

• HOW CAN I PREVENT THE ADOBE BEING THE SYSTEM THAT RECORDS MY DOCUMENTS?

  HOW CAN I PREVENT THE ADOBE BEING THE SYSTEM THAT RECORDS MY DOCUMENTS?

  You must associate the file with MS Word .doc extension.

  How to change file Associations in Windows | eHow

• How writing protected for the system disk?

  Hello

  I wanted to delete some files on the external hard drive. He cannot because of the write protected. So, I had to go to the registry editor. HKeylocalMachine-> system-> CurrentControlSet-> control-> StorageDevicePolicies.That is protected with DataSet '0' means write-enabled. If I change the value "1" is disabled. Having administrator rights, it can activate and disable write protection. But when I allow it, it does not appear the disk write protected when deleting message.

  My only concern if someone uses the system, if they accidentally delete the file, it would be a big problem. I ask you please tell me the procedure on how to set writing disc protected by default. Which would be really appreciated if you can tell me the method.

  Operating system: - Windows XP MCE - 32-bit

  Thank you very much.

  Hello

  It depends on the software you use to write protect the disk.

  I suggest you to check with apple support for questions regarding the iPod.

  http://www.Apple.com/support/iPod/

• Events shown in the range of navigation when you view the properties of the system for recording of JFR

  Which record the events shown in the range of navigation when you view the Properties tab system for a Java flight recorder? I'm guessing that they mark the time for JFR's writing of the events on the disk.

  I ask because, during the capture of a lot of information with the help of JFR, we see two effects that correlate with these events: (1) CPU usage ramps up a little bit between an event and the back then, level departure after each event, even if the application workload is constant; (2) the clock used to time stamp on all the events THAT JFR capture high-resolution seems to run more slowly in the period following immediately each of these events, perhaps for the period while JFR is written to disk. The slowdown of the clock appears as an increase in the rate of events shown in the range of navigation in other tabs - I also analyzed the events selected out of the original EN file to check their apparent rate.

  I see this on Java EE applications running on JBoss EAP 6.x on Java 7 on machines virtual small vSphere.

  The events shown in the navigotor range in any time must appear at the same time they are created. not when they are written to disk which can be a little later, depending on the settings.

  In the System Properties tab, you generally see a single spike per segment in your record. You should see the same thing if you go to the tabgroup events and enable only the Java Virtual Machine system property / Initial if Types discovered.

  As for the damages of its use and CPU timestamp, it sounds interesting.

  What exact version of Java 7 you use, there would be some bug fixes in later versions.

• XW4400 does not start. Occurred after the power to the system off for 2 weeks. Now, does not start. Help!

  As noted above in the subject... exploded with power for about 2 weeks supply.  On his return the

  system won't start.  It keeps going in a circle.

  Here's what happens;
  

  (1) it goes to the window HP

  2) immediately goes to a window stating "windows did not start properly. A recent hardware or software change might be the cause. "Then on and other causes.  Well, none of them took place.

  To the bottom of the window there's several options to try.  Safe mode, Safe Mode Networking, last known successful... and start normally.  All the options have been tried several times.  To 30 sec timer waiting for your choice.  NONE OF THE OPTIONS WORK.  Cannot start in any mode.  After all of the selections it shows;

  (3) a flash of the microsoft windows screen and then we go back to number 1.

  Info on the system;

  XW4400

  • Manufacturer part number: ET115AV-CTO
  • Manufacturer: HP
  • Product description: ET115AV-CTO HP xw4400 Workstation computer desk
  • Product type: desktop
  • Form factor: mountable Convertible minitower on rack
  • Operating system: Windows XP Professional 64-bit
  • Processor: Core 2 Duo processor E6700 (2.66 GHz)
  • Front side bus: 1066 MHz front Bus up to
  • Chipset: Intel¿975 X Express
  • Memory: DDR - 2 667 MHz ECC unbuffered
  • Installed memory: 2 GB
  • Maximum memory: up to 8 GB
  • Installed hard drive: 160 GB
  • Hard drives: up to 4 SATA hard drives 2 to maximum
  • Expansion bays: 3 external bays of 5.25 inch and 1 external 3.5 inch bay 2-Bay internal 3.5-inch
  • CD DVD: 16 X DVD + - RW DL
  • Speed variators: controller 4 channels SATA 3 GB s integrated with RAID 0, RAID 1, RAID 0 + 1 capacity
  • Graphics card: NVIDIA Quadro FX1400
  • Expansion slots: graphics PCI Express (x 16) 1 slot 1 PCI Express (x 16 mechanically x 4 electrically) slots 1 PCI Express (x 1) and 3 long legacy PCI
  • Audio: Integrated high definition Audio with Jack Retasking capability,
  • Networking - communication: integrated Broadcom 5755 Netxtreme Gigabit PCIe LAN
  • I/o ports and connectors: front: headphone, microphone, 2 USB 2.0 and 1 optional IEEE 1394 a rear: 5 USB 2.0 1 USB 2.0 (internal) 1 serial port standard 1 keyboard PS-2 port 2 in parallel and mouse audio Gigabit LAN RJ-45 1 built-in audio microphone
  • I have no recovery disks!

  Hello:

  I can't help with your problem, because in this case, my recommendation would be to reinstall the operating system.

  What I can do, is give you information to get a set of recovery discs for your xw4400 for only $10 USD.

  Here's how:

  1. Enter the part number and the serial number on the top of the computer on the Silver label. The model # is a Compaq HP xw4400, but the part number is on this tag silver under the serial No.

  2. call HP at 1-800-952-7689, option 1 (ranking in the list in the option made restore disks).

  3. provide the information asked by the representative who answers the phone. Some simply ask for the serial No., some want at the same time, or they'll want just the serial number and the type of computer (xw4400).

  4. do you have a Master Card or Visa ready for purchase. They do not take discover. You will be charged $10.00.

  You will receive the discs by first class mail, or you can pay an additional $10.00 for shipping FedEx.

  Paul

• Protection of the system, the System Restore Points

  On my PC at home in the restoration of the system, must a check be in the area to monitor the automatic restore points (D) recovery disk, or a check on the system drive (C), automatic restore points only OK.

  Ruben G.

  Ruben, clear control of D: drive. Let the checked C: drive.

  Unchecking the drive D: will also prevent future error messages telling you that the drive is full.

  Example:

  http://support.HP.com/us-en/document/c01555992

• There is a strange folder in my Options for the Protection of the system!

  The tab System Protection in system properties, which gives you options of system restore, there is a system volume that looks like there's a number of clsid.

  It is outside the usual partitions. Is this normal? It does not appear in Windows Explorer.

  The machine is quarantined and not visit the internet more, so I can't give you the screenshot. But it's the name of the folder:

  \\?\Volume{d331125c-e4fe-11E1-B1EB-806e6f6e6963}\  Below these are the partitions C: and E:, I created the disk during a recent clean install. The new internal drive is a WD 320 GB Scorpio.

  Previously, Windows wouldn't start and gave me a hardware error. I took the bottom of the laptop, reinstall the memory, hard drive and DVD - RW, it blew out and everything close up. It works fine now.

  However, I also had a problem of malware with Rimecud! INF, DelfInject.gen! BE and DelfInject.gen! AF, which is the reason why I ask this question. This file would be a remnant of malware? I wiped the disk four times.

  Hello

  The mouse interface will not be infected by the virus.

  Refer to this link and perform the virus scan using Microsoft standalone system sweeper tool.

  Utility Spotlight: Repair the Infection from your PC

  http://TechNet.Microsoft.com/en-us/magazine/hh547009.aspx

  Note: The data files that are infected must be cleaned only by removing the file completely, which means that there is a risk of data loss.

  I hope this helps!

• Protection of the system for the recovery Partition...

  System protection is turned on for the C: partition that is NTFS.

  I note that the Protection system is OFF for recovery D:

  partition.  What is the State recommended for both?

  The recovery partition didn't need a letter drive, because nothing in Windows use it.  You use the recovery partition by pressing a special key combination when the computer starts.  For more details, refer to the User Guide for your computer. Boulder computer Maven
  Most Microsoft Valuable Professional

• 10.6.8 performer must update on 10.7 or more but the system only tells me no update available

  I'm on 10.6.8 update on my iMac, but require 10.7 or higher for the installation of the printer - my search for Mac update tells me no update is available. How updated?

  Open the Mac App Store and try to download El Capitan. If you get told that it is incompatible with your computer or not desired, choose about this Mac from the Apple menu, check if the computer has at least a Xeon or CPU Core 2 Duo(not Core Duo) and 2 GB of RAM, and if this is the case, click here and order a download code for Lion 10.7; the Apple Online Store also sells codes for 10.8 Mountain Lion to download, but it has the same system requirements as El Capitan.

  Back up your data and control your applications for compatibility before upgrading. In particular, Mac OS X 10.7 and newer do not support PowerPC programs such as versions of Microsoft Office prior to 2008.

  (138748)

• BlackBerry Q5 downloads from the internet only recording does not

  Help please, how to save internet downloads? It gives the ability to save, it automatically opens the file.

  I had the same problem. But all you have to do is to maintain the link until the open option box then u click on save the link to the file and it will save

• 2 available drives on the points of RECOVERY and OS (C) of the system and restore the protection settings

  Greetings! I am very confused and need help. Looking for just my restore points.

  I am interested in the protection of the system, I clicked on the system protection and under the protection option I

  available from 2 discs on protection RECOVERY settings (it looks like folder sign) and OS (c :)) system)

  Protection of RECOVERY: off

  OPERATING SYSTEM (C :)) System Protection is enabled. I clicked on configure I activated the setting to restore system and previous version of the files. Maximum use of 2% (10,00 GB), use current 962,89 MB

  Now, my question is this, if recovery protection be ON? When I click on configure, check "turn off system protection"

  What is the right configuration? Help, please. I hope I'm not confusing you either.

  No, do not turn on System Protection for the system recovery disk. Which is locked and should only be used when you need to do a factory restore (that reinstalls the operating system). Just keep the System Restore enabled for the system partition on which your Windows installation exist. Releasing it's easy: with Windows | ActiveWin | Laptops | Microsoft MVP