PS6210xs and PS6210x in the same pool?

Similar Questions

• Mix PS6110XS and PS6010 in the same pool?

  Hello

  We think about the purchase of a PS6110XS for a VDI project. (vmware view 5.1)

  Currently we have a San with 4 PS6010 (SATA/SAS) in the storage pool.

  Would you recommend to put the new hybrid matrix in the same pool, or should we configure a new pool to ensure THAT VDI will get the best possible performance?

  Any other consideration?

  (We do not see the performance in the existing configuration problems)

  BR

  Standal

  Unless you need the extra storage space of the existing pool, it would be a good idea to add this member in its own pool dedicated to VDI.

  Here's a case study

  en.Community.Dell.com/.../download.aspx

  This theme has other VDI information:

  en.Community.Dell.com/.../2660.EqualLogic-Technical-content.aspx

  It's a little old, but addresses the basin VDI sizing:

  en.Community.Dell.com/.../2642.Sizing-and-Best-Practices-for-Deploying-VMware-View-VDI-with-EqualLogic-Storage-by-SIS.aspx

  The other important aspect of the VDI is your SAN switch fabric, the case study has some good information on this as well.

  -joe

• Can you indicate several virtual private networks in the same Pool of IP on an ASA/PIX?

  Google and searched everywhere but it's difficult to expression and I struck out.

  Yes, you certainly can.

  If I understand what you're trying to achieve, is to say:

  -you have set up several groups, and you want to point all of these groups to the same Pool of IP.

  -If the above assumption is correct, then the answer is Yes, you can.

• You can install the server connection and security on the same virtual machine Server?

  I was looking around and found an old post that says that you could do.

  I tried the documentation view 5 but not a lot of luck there.

  If the deployment is small say 20 users view total.

  Could install you the connection and security on the same VM Server?   W2K8R2 64-bit?

  I certainly understand some of the security risks.

  TIA

  Marc Alumbaugh says:

  Any other ideas?

  No other ideas, but we have should stick to previous ideas and continue to work through them. You make progress in this analysis - continue! When it is correctly configured, you have configured the firewall/proxy etc don't not to block PCoIP and that you use at least seen 4.6 on the Client and the server, it does not work.

  It always seems that there's something blocking PCoIP in your environment - where the black screen.

  So when 'PCoIP external URL' on the login server is defined on InternalIP:4172, your View on the internal network Client connects fine. If you run Wiresahrk on your connection to the server to capture the connections, you will see a connection HTTPS turns on TCP 443. Then when you select a pool of offices you will see a PCoIP connection come in. It comes to 4172 TCP from the customer to the login server, then UDP 4172 also from the Client to the server connection as well as UDP 4172 in reverse. For this reverse part, the source UDP port will be 4172 and corresponds to the destination UDP port source on the incoming UDP packets. Check that this is the case. This will prove that the login server is gateway your PCoIP correctly.

  So far so good.

  Then, you switch to your remote Client to view from on the Internet. To do this, you assign the URL of the "external" ExternalIP:4172 PCoIP. Note that you don't need to restart the login server for this to take effect. It takes effect immediately. This IP address will be the public IP address which will probably through a NAT/firewall to access your connection to the server. You can start by checking that the IP address is correct using to connect to the server address when you satrt the customer to view. When you use the same IP address to the Client and through the authentication step, it will prove that it is set up correctly in terms of Routing/NAT etc. Then follow with Wireshark on the login server and observe what happens when you select a pool of virtual offices and get the black screen. You should see the same activity PCoIP on your login server model as in the case of internal test (i.e. starting with the incoming TCP connection on port 4172). View Client will use the ExternalIP address that you specified in the "URL external PCoIP ' to establish the PCoIP connection to connect to the server. So if you don't see this com 4172 TCP on the login server, or you do not see the packets UDP 4172 then something is blocking. This is usually caused by a firewall or a proxy blocking PCoIP.

  If this is the case and you do not see these packets to connect to the server, then run Wireshark on the Windows Client to view and see if you can see 4172 TCP and/or UDP sent to this ExternalIP 4172. If Yes, then you know that something (such as a firewall or proxy) between the Customer View and the view connection server it blocks.

  Let us know what it was.

  Hope it will be useful.

  Select this option.

• on the Iphone 7. How to listen to music, if we have a normal headset and charge at the same time?

  How to listen to music, if we have a normal headset and charge at the same time?

  < re-titled by host >

  It sopposed must be a wireless charging dock to be launched shortly if the dock does not so it is a disappointment

• When I opened my firefox on my mac - it opens to a blank screen. I tried to remove and redownloading but the same thing happens. How can I fix?

  When I opened my firefox on my mac - it opens to a blank screen. I tried to remove and redownloading but the same thing happens. How can I fix?

  Ahh. I thought you meant Subject: vacuum

  Start Firefox in Safe Mode {web link} by holding down the < shift >
  (Mac options) key and then from Firefox. Is always the problem?

  Start your computer in safe mode with network. Then launch Firefox.
  Try the sites secure web. Is always the problem?

  Start the computer in Mode safe;
  Free online encyclopedia

• can not put cookies and exceptions on the same screen. Need to fix this.

  Went to the options today and the format has changed. Now I can't put Cookies and Exceptions on the same page at the same time. It is vital that I can put together up to manage cookies. Please fix this. Anyone have any ideas?

  You can enable/disable browser.preferences.inContent false on the topic: page config to restore the autonomous Options/preferences window you had in previous versions of Firefox.

  You can open the topic: config page via the address bar.
  You can accept the warning and click on "I'll be careful" to continue.

  • http://KB.mozillazine.org/about:config

• I have two computers on the same router. One, on Xp and Eudora normally receives. The second on WIN-7 and Thunderbird receives the same messages in code -?

  I have two computers-
  On WinXp and Eudora receives emails in normal text.
  Sometimes, the other on Win-7 and Thunderbird receives the same message in code.
  Normally, this same message is received on the other computer.
  What have I've set wrong
  GerryMcDonald

  Start with view-> Message-> HTML Original body

• My iphone 6 does not light, I held the home button and power at the same time and no vibration or no sign of life, any suggestions as to what it could be would be appreciated

  Phone bought 3 days ago and I fight to turn it on, it's just a black screen, the phone records into iTunes but does not turn, I tried holding down the home button and power at the same time and still nothing, I presume that it's a battery problem as if it was the backlight then the phone vibrated when you press the power button help Please!

  Marley6921 wrote:

  Phone bought 3 days ago and I fight to turn it on, it's just a black screen, the phone records into iTunes but does not turn, I tried holding down the home button and power at the same time and still nothing, I presume that it's a battery problem as if it was the backlight then the phone vibrated when you press the power button help Please!

  Put it on wait ten minutes if the phone did not come one, then hold down the sleep/Home button until you see the apple logo and then release, make sure that the phone is still connected to the charger.

• My husband and I have the same phone.  We see the two of you on each of our phones calls him, and that missed us a call from (the phone number is in red when it's a missed call).  Thanks for your help.

  My husband and I have the same phone.  We see them entering and fact phone outgoing calls and missed calls (phone # is in red) from the other phone.  Thank you for your help.

  This happens when you both share the same Apple ID. It is recommended - for a number of reasons - that each have their own Apple ID and then uses the sharing of the family for things you want to share. http://www.Apple.com/icloud/family-sharing/

• USBOTG and Charge at the same time on Stream 8

  To keep this thread as productive as possible and efficient for those who find it useful to:

  Unless you have under your eyes

  1. a schematic representation of the 8 Stream USB port (USB port and battery electric circuit etc.)

  2 source code for the firmware BIOS and kernel that controls the material

  Please DO NOT respond or say "is not possible".  In view of the above is true, you do not have enough information to say '' not possible. ''

  If no one replys with a solution, what he calls not possible by default.

  Also please do not answer to say ' I don't know how "or" but I know how to do anything else that ' is also not that useful.

  An update of the BIOS or other software update may be required by HP, Microsoft or both to offer this feature really intuitive and quite possible.

  And I hope that this thread can be an effort consolidated by all who have the 8 flow to make the necessary changes.  The majority of the other tablet PCs are capable of it.  It seems that only the 8 Stream and a few others have trouble with her.

  ~~~~

  I want the ability to use a simple, inexpensive cable and perhaps standard (with electronic active minimum inside) which allows me to host and to use one or more USB devices on the Stream via its USB port B microphone 8 while this cable can also be connected to a charger standard and charge 8 flow simultaneously.  This means that the cable has a minimum of three connectors.  One of the possible configurations are as follows (apart from the normal charging cable):

  1 cable Micro USB B Male - connect to the stream 8

  2 USB male A - connect to the AC charger (IE one that came with the 8 Stream)

  3. USB A female - one or several connectors to plug into the key of USB data, keyboard, mouse or even a hub.

  Connector # 2. above shall provide a power supply to recharge the 8 Stream via conn. #1 and the power supply for external USB devices via conn. #3 so that they are in use - all at the same time.

  A and if the same cable can act as a normal OTG no charger for when no external power supply is available.  This may necessitate a switch or an electrontics active inside.

  The last part of this goal is unimportant for various reasons.  I wish that HP, the manufacturer of 8 flow, to State in writing good mode necessary to do this, so that other manufacturers or even-it yourself can make maximum use of their tablet HP equipment.

  ~~~~

  The neat thing it will alow a person to do with their tablet, it is to work at home using the Tablet as a desktop PC by connecting a keyboard, mouse, perhaps external screen (with USB to the display adapter) and knit for a long time without time limit prescribed by the battery life because the charger provides energy to all involved.

  If there is only a single connector on the cable #3, then an additional node of coarse had to provide support for these multiple USB devices at the same time.  However, it would be better if there were several #3 connectors integrated in the cable itself.  This would be better as a suitable USB hub also requires its own power.  That an adapter is necessary if the whole thing were integrated into one.

  ~~~~

  I really want answers from anyone who has already accomplished USB OTG delivered with simultaneous load with flow 8. (independent of any published 'proper' way is also welcome)

  Today's date is 2015-01-16.  If in 2015-02-16 (one month), nobody has posted a solution and then starts to bug HP and Microsoft on it's us?

  ~~~~

  Technical training:

  I understand the possibility the tablet software and firmware must take a decision on the manner in which power flows on the power port USB microphone B pins.

  I know that with a proper design of the electronic circuit carring these signals of power inside the Tablet could be sensitive to what is connected and without risk to decide for himself what to do without needing to control software.  For example by testing/detecting periodically differential voltage or current management to see what sides of the connector can supply.

  But this is only one of the many "could bes".

  In addition, this can be no standard regarding the standard USB.  What seems to be actually the case with a lot of cables OTG + fresh, is that physical clues embedded in the cable or charger are used to signal to the Tablet what the situation is.  Then the signal of software/firmware of the Tablet, interprets what the situation is intelligently and responds by flipping the bits of correct hardware control to activate, or deactivate the power flow in the port and also control its direction in or out.

  I'm not familiar with the standard USB.  Maybe I could do more research, if I believed that HP followed with 8 Stream or even the standard covered this situation explicitly.

  But to a certain extent, it seems I'll have to invent something that should be intuitively just like it does with other tablets. Isn't it?  Maybe I'm overthinking, but I can't find any USB OTG + cables load that specify compatibility with 8 HP flow.

  In any case, I was familiar with both methods other use of tablets to send the highest mentioned signal to the hardware/firmware/software of the tablet to the idea that it's time to load / time of OTG or both.

  The first method is a 0 Ohm to 200 ohms short between pin USB A 2 and 3.  This is the bidirectional data differential lines D - and D + respectively.  In data mode, all the data passes back and forth on those lines.  When you load with a cable, it's the charger module that puts this short, not on the cable.  I measured the short on three different Chargers.  It is 0 Ohms on two of them, one of those who are the charger that came with the 8 HP flow.  The others 0 ohms was generic.  The third was for an apple iPad and it measured on 53KOhms.  It's probably not the resistance ohms 0-200, but probably it is impedance termination indicating that there is some intelligent serial port communication in the charger itself.  Leave it to Apple to be different.

  This method is somewhat questionable, as this signaling mode would prevent OTG + fee because it seems unlikely that you will be able to OTG when the data lines are shorted each and overloaded with such low impedance.  I could be wrong on this subject...

  The other method I have seen suggested to work with some tablets and phones other than the 8 stream is too short the USB microphone B pin 5 to Terminal 4 with 0 Ohms to 100 000 Ohms.

  USB B has 5 pins.  USB has only 4.  The extra pin on B moves the GND pin 4 pin 5 pin to and makes pin 4 PIN ID.

  If this signal applies to a drop in the ID pin (4) or in some cases, I saw that she proposed, he runs down with 0 Ohms.

  Dead shorting things always makes me nervous.  If ID is a simple normally high impedance high input, resistance could be used to make voltage well below the low or zero threshold while also preventing the risk of damage when cheat on him with a device that you do not have the diagram for.

  Yet, 100K is a bit high for a 'pull down' in most of the situations that I'm used to.  Even a 10K would be uncertain. A 1 K or 2 K seems reliable enough, but then things are weaker and in know more nowadays low...   All but a dead short but if possible.

  So, it seems possible that the device might be able to "indicate" by the specific value of the resistance, which can be found here.  In other words the resistance is not a pull down but in fact a signature analog ID, in which case the exact value will be crucial. So if this is the case, a guess is not going to work.

  Obviously in such a system as described above, a chip inside the Stream 8 should be responsible to support this information. I hope the 8 Stream has such a chip.

  Probably a register inside this chip would be at all times what the State of the pin ID is a binary number.  All that is needed is for the BIOS to the chip and the registry in it and read this number via the bus to determine what happens to the port. Finally, he would use that signals of info to send the order of material to the electrontics of power set the appropriate direction to take etc.  (and change the State of the icon on the screen of the rude)

  I don't know if the PIN ID method described is a standard USB or not either.

  Eventually, there may be a third way. But I do not suspect that it would be possible with a non-active external device. In any case too complicated for the novice DIY for sure.

  The device would need to act is a kind of extension of bus.  As an active hub.  But she would use the negotiation of data USB serial lines and in addition to reproduce one or more additional USB ports, intelligently inform the tablet to get with the program which is "now we're going to otg and recharge at the same time."

  This requires a smart external device with a processor Inside, no doubt.

  It seems to me that many other tablets have been able achieve avecjoint here the need for a smart external device and thus the flow must also be able to do.

  There is a device that claims to be able to work with the HP Jet 7 and 8 and provides same ethernet and USB and big DVI ports so loads the data stream.  But its expensive because it is active.  Se here:

  http://AMZN.com/B00OVDE0GC

  It's called a "Docking Station".

  A reference to a product that does exactly what I want (possibly without active electronic components) is here:

  http://AMZN.com/B00LTHBCNM

  It's by Kirin and it is a device of type squid with four USB ports.  Precisely, which is my goal.  But read in the comments stream 7 user indicated that he would not be OTG and load, not really clear if it worked as a hub USB OTG or not.  Another evaluator stated that she would not support even a single USB device much less fees of 8 Stream.  This device has a switch.

  I forgot to mention that some 'hackers' have claimed success with other tablets to deceive their devices by using a multi-step process to plug things in.  Usually in general they would get connected Tablet and load first, then they would return a switch or something remove some resistance or the signal was introduced by the first position of the switch. For some reason any Tablet would continue to require. Then the data lines would be free and they would plug in a usb key and it mounts correctly even if the tablet was always in charge.

  It's like the power circuit has a lock which does not allow it to return to the mode "power flow" as long as he still feels the power flows inward regardless of what software it is telling.  Full proposal here.

  These tips seem dubious to me.  Changes in the BIOS could change the way it works.  Also you can not be sure what actually happens if you do not have a schematic representation.  You could damage your tablet.  Many people will support icon in the operating system whether the Tablet is in charge.  But I'm sort of a low-risk guy and my policy is generally indicators of intereperet not to have meaning at all once a device is functioning in a non-standard setting.  Especially when it's something that I did not built and could not fix if I FRY.

  Hypothetical reasoning: tell me what data sensory discs really the State of the charging light screen?  This reflect the bit of hardware control programs actually feeding management and status on the port?  Or does it measure the direction of the flow of power, said in the section of the circuit battery monitoring?  Point - none of us have a schema because it's owner. To really be sure according to the smart electronic hardware, the port must be mode flow under advisement "of power. If it's in a "power flow out" mode and power will be delivered externally as well you wind upward with both power supplies the same power at the wheel nets.  In this case, the two opposing regulators attempting both to drive 5 V can have slightly different voltage calibrations.  That could lead to fighting between them, with more than 100% of their capacity.  For example if you try to regulate 4.95 real V and the other and other attempts to regulate 5.05 V.  Current then flows to the tune of 100 mV / a few milliohms in the cables linking the two.  This may be several amperes. (many)  In other words, like I said: you want the tablet to know that power is coming in don't go out and automatically hitting the internal switches needed for that to happen. Probably the icon should indicate this with precision, but in some wacky situation, he could not. There may be a chance that the icon could indicate the load and still be burning or focusing on some circuits of the tablet or the charger.

  Another thing, I could see that happening is if you play with these reported resistance types enough you might find a resistance value that winds up place the device in an intermittent condition.  In other words it keeps flipping back and forth quickly between OTG and fresh.  It can give the illusion that it works.  You can have marginal communication with your USB devices and battery could even load.  But will still be a lot of stress on the power circuit.

  It is difficult for me to risk a Tablet perfectly well if I don't know exactly what I'm doing.

  If a brave individual makes their own experimentation and verifies that it charges and OTGs and you tell the rest of us, you're a hero.

  Maybe one of you has a good knowledge on the USB standard to have more confidence in such an experience... like what the ID pin 4 REALLY supposed to work for example?

  That's what I know so far.  If you think you can help, thanks in advance, or if this helped you, then your quite welcome.

  It works

  http://Accessories.us.Dell.com/SNA/ProductDetail.aspx?c=us & l = to & CS = 19 & SKU = 470-abes & baynote_bnrank = 0 & baynote_irrank = 0 & ~ CK = baynoteSearch & dgc = CJ & cid = 47997 & lid = 4279734 & acd = 10550055-4485850-eb75dcb47e53437680ed323a1f4885fe

  Evidence

  http://targusblog.com/2014/11/25/how-to-turn-a-99-Tablet-into-a-workstation/

  But it's 4 x the price in Europe

  Have fun

• Satellite M30X-122: how to use the headphones and speaker at the same time?

  Hello

  y at - it a possiblity to use headphones and speaker at the same time?
  When I plug the headphones into the Jack, the speaker is created off the coast of the moment.

  Thank you
  Peter

  Hi Peter,.

  There is unfortunately no way to use both headphones and speakers at the same time. This is because tghere's a disconnection physical power for the internal speakers when you plug in the headphones. It is not by software. The only way around this would be to dismantle the headphones Jack and solder connections that are broken when you insert the headphone permanently.

  Kind regards

• Is it possible to rotate the two iMovie 9 and 10 of the same MacBook Pro?

  Hi all

  Please be gentle with me; I have only just joined the community.

  I have an Apple MacBook Pro 2015 running OS X El Capitan; I used iMovie 10.1.1 and have already fallen on its limits.

  I would like to export to Quicktime so I can have more control over the settings (fps / sound, etc.) of my videos created with 10.1.1 before posting on You Tube, but can do with 10.1.1. I would like to download 9.0.9 and have both versions on my Mac (I understand that you can have both on the same machine) and you can / export to QuickTime with 9.0.9 share.

  I tried to download from the official website of Apple but encounter the following:

  "This update has no need to be installed. A new version of iMovie is already installed"

  It is no possible to navigate around this alert.

  Is it possible to have the two 9 and 10 on the same Mac, iMovie as 9 has never been installed on it, and if yes, how does one?

  Thanks in advance!

  J0hnst0n00

  What you propose, it's really not the way to accomplish what you want to do. iMovie 9.0.9 is not available on the App Store and can be purchased as part of the package iLife online from a third party like Amazon. Also, it is not completely compatible with El Capitan. Certainly not the right approach. I suggest you get MPEG Streamclip against 5 squared, which is downloadable for free. Share your iMovie project to file that will give you a MP4 file. Open in Streamclip and you can save as a Quicktime movie. It has a complete set of options, including the choice of codec, rate, etc. to image size.

• Satellite Pro L770 - 14 H - the use of WLan and Bluetooth at the same time

  I have a Satellite Pro L770 - 14H and you want to use a Bluetooth mouse.
  With the 'FN' and F8 key I am capable of coding between WLAN and Bluetooth, but it is not possibel to have both at the same time.

  My question is: How can I have WLAN and Bluetooth at the same time?
  To use a Bluetooth mouse with WLAN connection.

  Thank you very much
  Helmut

  Hello

  Using Win 8.1?

  Usually you could turn on and off Bluetooth in Win 8.1
  Settings PC-> PC &-> of Bluetooth devices

  There, you can move the cursor to BT for THE position.

• Is it possible to use iCloud shares photos with the two opening and Photos at the same time?

  Is it possible to use iCloud shares photos with the two opening and Photos at the same time?

  Non - PEAK is not a feature of iPhoto or Aperture - this is new with Photos

  LN