Questin - DX4870

Similar Questions

• Gateway DX4870-UB318 - new video card

  I have a Gateway DX4870-UB318 computer with Intel integrated graphics.  There is a slot PCIe 3.0.

  I just buy a new PNY GE Force GT video card 2 710-gig.   This card requires only a power supply, I have 300 Watts.

  When I isntall the map, it freezes at the screen to start the BIOS for a few minutes, until he finally arrived with a screen showing the details of the card - just what kind of card it is, memory, etc..  Let it sit longer, does not seem to get further along the boot process.

  If I remove the new card and return to the integrated graphics card, it works again.

  I installed the latest version of the BIOS for this PC on the site of the bridge, hoping that could help or give a few additional options - such as secure boot power off, what could be the cause, based on some of what I read.

  Anyone have any ideas on how to get this working?

  Details on the PC:

  http://www.CNET.com/products/gateway-dx4870-ub318-core-i5-3330-3-GHz-8-GB-1-TB/specs/

  The details on the purchased map:

  https://www.PNY.com/GeForce_GT_710_2048MB_DDR3_PCI-E_2_0_Low_Profile

  If anyone has this problem, I have now received a response from PNY.  They indicated that I would need a card not in line no UEFI.  Unfortunately, the BIOS on this computer will not support this card.

  They recommended the GT 520.  I don't know, but it is possible, it is the last of the cards that don't require UEFI.

• Gateway DX4870 - What BIOS for the dual-boot Win8 & Win7?

  I have a Gateway DX4870-UR10P desktop computer, with Windows 7 Home Prem 64-bit.
  The bios is originally shipped in 2012.

  I want to run Windows 8.1 PRO 64-bit - disk a hard nine separate. And keep Win 7 on the original hard drive. I probably will add 10.1 Win or above on a drive partition in the future. BTW, I run the Hyper-V virtualization in Win 8 other (Windows XP, Linux).
  Download of the available bios (they also list Linux pkgs)
  Gateway BIOS - UEFI for P11 Windows 8 (not for updates). B1
  Gateway BIOS P01. A2

  If I update the Bios to P11. B1, continue to support Win 7?  In addition, win 10?
  Is P11. B1 correct to use bios? Did anyone see any issues, "traps", config problems?

  Thank you.

  You can update only to this:

  Gateway BIOS P01. A2

  BIOS P11 is reserved for the DX4870 who had 8 windows of the factory (no updates)

• Gateway DX4870: openal32.dll

  Today, I tried to open a game that was working fine 2 days ago and received a message "OpenAL32.dll". What is - this and how to fix it. How is it past when the game was working fine

  As the message says, uninstall the program and reinstall it.  Why it disappeared I can't say, maybe some update.

• PhoneCall questin

  Hello

  I have the following code:

  PhoneArguments phoneArgs = new PhoneArguments(PhoneArguments.ARG_CALL, "1234567890");
  Invoke.invokeApplication(Invoke.APP_TYPE_PHONE, phoneArgs);
  

  Now, in the next line, I want to get the instance of the object the initiated call PhoneCall. How can I reach it?

  Thank you.

  I don't think that there is another way.

  What bothers you about the interface of PhoneListener?

• Why have I been questined on the problems in my association, if the credit card has been correctly debted?

  I use a PC for Windows 8.1 with an I7 processor. My creatinve cloud app works very well, but I got a message saying

  "You are not connected to the internet or there is a problem in your account... check payment information...". 1 day left... "(in Portuguese, I installed the creative cloud...)

  Contact Adobe technical support via chat and describe your problem to them.

  Chat support - the link below click the still need help? the option in the blue box below and choose the option to chat...
  Make sure that you are logged on the Adobe site, having cookies enabled, clearing your cookie cache.  If it fails to connect, try to use another browser.

  Creative cloud support (all creative cloud customer service problems)
  http://helpx.Adobe.com/x-productkb/global/service-CCM.html ( http://adobe.ly/19llvMN )

• where to save downloaded files? iPod Touch

  Hello

  Starting at all things Apple, so looking for help, while I still have some hair left.

  I am at a total loss, so I hope someone will hold my hand and guide me through the first steps. Once I downloaded a few MP3 files on my PC, where to save / move then I them to iTunes, so that I can then transfer them to my iPod? The following questin I ask will be ' and how do I do this?

  Thank you for those who started on MS-DOS and grew through the windows (and now Android).

  Ken

  First (to be sure) you have installed iTunes on your computer - correct?

  http://www.Apple.com/iTunes/download/

  Then, you can find these useful for importing music into iTunes:

  12 iTunes for Windows: importing music and video already on your computer

  12 iTunes for Windows: import songs from CD

  Then finally, sync them to your iPod:

  Sync your iPhone, iPad or iPod touch with iTunes on your computer via a USB - Apple Support

  or

  Sync your iPhone, iPad or iPod touch with iTunes using Wi - Fi - Apple Support

• Pavilion Elite m9452p: Flying Blind with a HP Pavilion Elite m9452p - no video at all - HELP!

  It is a Core 2 Quad Q8200 processor Intel PC with 8 GB of RAM and 750 GB drive HARD + 1 TB back up drive running Windows 7 Ultimate 64 bit (it came with Vista 64-bit home edition Premium, but updated for win 7 just now).

  It has always worked perfectly, but last week there was no video at all when I turned it on. The monitor says 'No Signal' on an otherwise black screen when turned on.

  HDD lights indicate activity and I can hear readers spinning and the LEDs for the DVD and the wireless signal light up as well.  In addition, ports Ethernet led Flash and show activity, as does the DVD player if I put a disc, but no video at all.

  I did the following to try to resolve this problem:

  1. I checked the monitor I was using is working;

  2. I always connected this PC to another monitor DVI to work with no luck.

  3. I have connected the PC to a working VGA monitor with no luck.

  4. I connect the VGA monitor to the VGA port, integrated with no luck.

  5.i tried to boot in the BIOS, but there again, no video is not sure if it goes to BIOS or not;

  6. I have read somewhere that the built-in VGA port will not work if a video card is present, so I removed the video card of exisitng and connected to the VGA integrated with no luck;

  7. I bought a replacement video card (it came with a MSI V240 500 MB PCIex16 card and got a card XFX Radeon HD 5450 1 GB PCI ex16); I installed the new card and tried again without success;

  8. I don't remember if this PC was set to beep on the POST before he always started quickly and without problems. Now that I'm looking for any beeps, I don't hear everything but yet once, can't remember if it still beep before;

  9. looks like it's a hardware problem, but I also tried to boot from a drive of W7 64 Bit repair, but even once, no video so don't know if it works.

  The last thing I remember having seen it was a Windows Update I think to include an optional update to the video driver. I don't remember if I acdcpeted that one or not, but it seems to me that the drivers for the MSI card (nVidia, GE Force pilots I think) that does not correspond with an AMD Radeon graphics card drivers - this is why I opted to get the Radeon card).

  I have not tested the original map, mainly because I don't have any PC with which test (I have a Core 2 Duo Pc with a PCI slot ex but not an ex16 PCI card. I don't know if this card would be retro-compatible with this PC or not).

  I vaguely recall disabling the onboard VGA in the BIOS, but do not remember if it is with this PC or another.

  I hope someone has a way to put video on so I can uninstall all recent drivers or updates that may have caused this (or I can enable VGA integrated in the BIOS).

  I sure hope the MoBo is not messed up (it does not fuel upward hard drives, the DVD player and the fans, etc.) but with no video, it is difficult to know what is happening.

  Help!

  OK - SOLVED!

  After re-reading my post, I realized that if the BIOS for the integrated video card setting had actually been changed, I could re - put these default settings by resetting the CMOS.

  I had not tried to clear the CMOS by the cavaliers to the MoBo, so I'm the manual MoBo and I cleared the CMOs (which would reset the BIOS to factory settings). I restarted the PC and voila! I now have the video!

  Sometimes the simplest things will solve the whole problem!

  I felt bad that I couldn't solve this problem, as I can usually solve everything that came out on any of my systems, but here I answer my questin oiwn and solved the problem - I hope this will help others too!

• Damaged by a new original drive replacement.

  I hope I chose the correct boad...  Our Pavilion dv6 - 2173cl hangs after the display of the: wallpaper with the fame of the taskbar and the Start button logo Hp and Date/time button. The cursor shows with the blue 'busy' ring for several minutes then all 'freezes' requiring the use of the switch on the case at the stop.  This happens also in Mode without failure.  HP Daignostics returned an error code of 9077j2-50e656-xd0021(7? sorry wrote it in a bit of a hurry, lol)-6ou103 for the car test.  We can always get on the drive as a "slave" drive for personal info, settings are available.  Replacement is practically a given drive, I'm just wondering do the new disk a «plain» W7disc  So my questin is "are required HP programs? "Or are they just ' space takers?  I suspect a problem of overheating, such as case initial drivr a fading... Probable cause of the damage of disk... Right?  All we need is a working disc until finances allow you to buy a new computer. Probably about February.

  That has always worked, I've never had it fail.

  The only thing I can suggest is to make sure that the key is correct.

  The entire disk must be removed to create the space unallocated on the entire disk. Just formatted it is not enough. After you have created no allocated space leaves the Windows disk format automatically, don't do it yourself.

  Here's a tutorial that describes what I'm talking about.

  http://pcsupport.about.com/od/OperatingSystems/SS/Windows-7-clean-install-part-1.htm

  A place to download the ISO of most of the W7 version, if you need it.

  http://www.mydigitallife.info/official-Windows-7-SP1-ISO-from-Digital-River/

• The use of registers at offset in a while loop that never loop

  Here's a picture of 'syslog_Device function Engine.vi. This isn't really a question specifically about this vi, but rather a technique I see here.

  First thing I noticed, it was a while loop always outputs, never loops. And shift registers. This serves for the VI can retain values between calls, almost like what I consider a local variable which are persistent between function calls in another language? It is an interesting way to accomplish what I have not looked at.

  Please tell me if I'm missing what is happening here.

  

  It is a driving force.

  It's a code construct that allows you to encapsulate data and features that are available in multiple threads.

  The nugget I linked above explains their operation the theory behind them and follow-up discussions in discussion on how to exploit them.

  Good questin incidentally!

  Ben

• Ram HP p180ca 17 slots

  Just a quick questin on computers notebooks 17-p180ca of HP model. Did anyone know how many ram slots or memory is n it? Also what is the maximum ram your laptop can handle.  Thanjs in advance

  Hello

  This unit supports up to 8 GB of total RAM that is combining the two RAM slots.

• How to use the commands on the cmd prompt witout using a string like 'netstat' but I need output

  How use the commands on the cmd prompt witout using a string like netstat but I need output
  example: C:\ > netstat-an... will give its results
  But if the keyword netstat is blocked...
  I want to use the command netstat another way... can I convert it to binary, and then I can run or something else
  Please answer my questin

  Netstat is simply a file program located in the folder C:\Windows\System32.   It appears as "netstat.exe.  If you rename (or copy / paste / rename) to "abc.exe" then you can run it using 'abc' instead of 'netstat '.

  HTH,
  JW

• Delete Playlis & recognition of Micro SD

  Thank you people of my previous questin family.  Very useful information.  Now...

  Please keep things simple: 1. How can I delete my Fuze 8 GB playlist?  Formatting is the only way?

  2. what should I do if my Fuze 8 GB rrecognizes files on the micro 2 GB cards?

  I use Windows media, and I was now 4 days, am a quick learner.

  Thank you all in advance for the help.

  1. to delete a Playlist you go in the "rocket" thru 'My Computer' as if it were a hard drive and then the folder selections, find the files with the same name that you want to get rid of the playlist. If you want to remove the files of the song, you will have to do it manually by going to the music and deleting each file folder.

  2. all you have to do is plug in the SD card. The "rocket" will do the rest. It does not differentiate the internal memory card while playing. When you plug into your computer and open Windows Media and click on the Synchronize tab, it will give you 2 options of your should say something to the effect of the Sansa Fuze 8 GB - internal memory, and the second will be Sansa Fuze 2 GB - uSD card

• "Your computer could not renew its address from the network (from the DHCP server) for the network card"?

  I saw this question posted several times here, but I can't find someone who has exactly the same problem I have.

  This problem started a week ago. Basically, my computer loses its connection ethernet once per hour to around the same exact time. which is only for about 5 seconds, but it's enough to get Skype and other things while I'm working, and it's very frustrating because I use Skype to talk with customers, and it looks unprofessional when my calls fall every single time. my computer can also use wireless (which does not go down), but he's too unstable for my work.

  now on the error message I posted. I get this error in my observer of events in about 30 minutes until my ethernet goes down, so I don't know if they are interlaced or not, because I don't get any errors when my ethernet really crashes.

  Here's what I've tried so far without success:

  -temporarily disable the firewall and antivirus

  -updated driver for both my wired network cards and wireless (both were UTD)

  I don't know what to do because I've never had this problem before.

  Here is some information on my computer if that helps all:

  OS: windows 7 Home premium (x 64-bit)

  computer model: gateway DX4870

  Look on the side of the router and make sure that the DHCP lease time has not set to 60 minutes.  As a simple solution you can just assign a reserved DHCP or a static address to the computer (in the router).

  PS: You'll find the DHCP lease on the map with the command ipconfig/all command at a command prompt

  John

• HP Photosmart 7520 vs 7525

  Forgive me if this is the wrong place to post this questin, but I could not learn the difference between the HP Photosmart 7520 and the HP Photosmart 7525 anywhere.  Y at - it you to experts who can direct me to where HP provides this information. or someone on the Forum has the answer?

  Hello

  The HP Photosmart 7520 and 7525 provide the same exact features, ones that are just different 7520 series models.

  You can find the specifications below:

  http://support.HP.com/us-en/document/c03369370

  Shlomi