question about speed

Similar Questions

• Satellite L650-11R - a few questions about this

  Hello there :-)

  I have a few questions about my new L650.

  I've never had Toshiba notebook before so I apologize if some of these "quirks" are actually quite normal on this laptop. I really want to hear the views of other users L650.

  1)
  First of all, by the time I turned it on I saw gradient thin (1-2 mm) along the right edge of the screen that goes from the bottom up. Maybe "degraded" isn't the right word, but it seems that since two or three pixels are kind of discoloration or lose brightness/sharpness to the edge along the straight bezel. It is not really that visible, looks like the colors are desaturated a bit here or brightness is a bit lacking. He can be seen everywhere (bios or no color in Windows, but better in the lighter background).
  The left side (or other) seems ok, all this along the right edge is somewhat suspicious. If one can compare? I don't know if it's something to worry about or is just supposed to be like that.

  2)
  The other thing I noticed heating of the processor (Intel i3 330M) and GPU (ATi Mobility Radeon 5650). It's pretty hot here right now (I would say that the temperature is around 28 degrees Celsius when using cell phones). He is sitting on the hard surface (table) and nothing is blocking the vents.
  However, at "rest" (surf the web & regular light stuff), average CPU temp hovers around 58 ° C. It usually goes from 45 to 62 in just a few minutes after starting, and then I can hear and see (Toshiba PC Health Monitor) evacuate the kicks in. Temp goes back to 50 +, event stops and then the temp rises to 60 + until the vent is used again.
  During load full (Prime95 or some games), CPU is going all the way up to 75 degrees (the highest being 77). Fan runs at 75 to 77% during this time, never go faster.

  GPU idling is usually around 5 degrees above temp CPU (62-65). During full load (for example. Benchmark of Far Cry 2), I see a lot of stuttering with the latest drivers Catalyst and DX10 (not sure if the stuttering has something to do with heat), otherwise it is ok (no artifacts or anything like that). Temp of GPU during the loading goes up to 74-75, fan speed is locked at 30%, the frequency of the heart 5650 is 450 MHz. left side of the laptop (vent and below) is pretty hot, while the keyboard is warm (or slightly warmer who who).

  These time seems correct and safe in the long term? I'd rather events works all the time (they aren't really very strong) and keeping time less than 50, but there are just wishful pious bios control events and I can't control not the bios. :-)

  3)
  This is just General related products. :-)
  Official specifications of Toshiba L650 say ATi 5650 (between other low range GPU), but I saw a few specifications calling for there 5730 (same model 11R). Is there really a Satellite L650 with ATi 5730 GPU models?

  Sorry for the long post, I tried to include the best possible description that I could do. :-)

  Thank you in advance.

  Thanks for the additional info!

• A few questions about the upgrade on Satellite A300-144

  Sorry for the typos, English is not my mother tongue.
  I want to ask some questions about the upgrade of a300-144.

  * Some info first.*

  CPU: T2370 ([http://ark.intel.com/products/34445/Intel-Pentium-Processor-T2370-1M-Cache-1_73-GHz-533-MHz-FSB]).
  Chipset: GM965 ([http://ark.intel.com/products/29821/Intel-82GM965-Graphics-and-Memory-Controller]).

  * Questions.*

  1. my frequency of laptop memory at 533 MHz, supports 667 MHz memory controller, memory modules can work at 667 MHz. Is - this because CPU FSB 533 MHz frequency and new processor at 667/800 MHz FSB will fix it or it is hardcoded in the BIOS?

  2 Intel said that the size of max memory for my chipset is 4 GB (2 x 2 GB), but Toshiba says that only 2 GB (2 x 1 GB), who is right?

  3 I know, taken of my CPU is μFCPGA-478 aka socket P, max FSB 800 MHz, max 35 W TDP, so T9500 ([http://ark.intel.com/products/33918/Intel-Core2-Duo-Processor-T9500-6M-Cache-2_60-GHz-800-MHz-FSB]) is a compatible processor or there are some limitations in the BIOS?

  > 1. My frequency of laptop memory at 533 MHz, supports 667 MHz memory controller, memory modules can work at 667 MHz. Is - this because CPU FSB 533 MHz frequency and new processor at 667/800 MHz FSB will fix it or it is hardcoded in the BIOS?

  The speed of the memory is related on the material. This means that the FSB is responsible for the limitation.
  If the FSB would allow support 667 MHz then the memory would also at this speed.

  > 2. Intel says that the size of max memory for my chipset is 4 GB (2 x 2 GB), but Toshiba says that only 2 GB (2 x 1 GB), who is right?
  The memory depends on the chipset. So if the chipset supports 4 GB of RAM, you should be capable of this move to 4 GB of RAM

  > 3. I know, my CPU is? FC-PGA-478 aka socket P, max FSB 800 MHz, max 35 W TDP, so T9500 (http://ark.intel.com/products/33918/Intel-Core2-Duo-Processor-T9500-6M-Cache-2_60-GHz-800-MHz-FSB) will be a compatible processor or there are some limitations in the BIOS?

  It might be possible that the new processor would be fully supported by the BIOS, but in most cases it should not be a problem if the chipset would support the new processor.
  But as far as I know the upgrade of the CPU is not supported by Toshiba or any other manufacturers of portable and its your own risk to run laptop with the new processor.

• Satellite U405D - several questions about overheating/disassembly/upgrading etc.

  Hello

  I have several questions about my old one by Satellite U405D-S2910

  1. when it works, after 2-3 hours (I run usually small programs such as safari, msn messenger and bsplayer) CPU gets 85 to 90 C (178-188). When I play age of Empires 2 (come on, its an old game) like 2-3 hours, it stops. What could be the possible reason? Furthermore, let me inform you about the climate of the city I live, 30 c temperature - humidity 25-35% (today).
  PS. CPU is AMD Turion 64 X 2 Dual-Core Mobile Processor. Model RM-74

  2. I'm going to disassemble my laptop in order to clean its cooling units (I think at the rate of overheating is this). It does seem like a desktop computer, so complicated. Ive seen a disassembly not to not (btw, its so difficult to spell dismantling :) I think Im going to do this. What are your suggestions on this subject? experiences could help me?

  3. my laptops is Ram 2x2gb PC5300 DDR2 667 MHz SDRAM memory, I want to replace RAM memory 2x2gb MACH XTREME DDR2 1333 MHZ CL9 NOTEBOOK. Should I do it? Fit my portable, stable work? any suggestions?
  PS. motherboard chipset AMD M780V

  4 - Finally :), should I use OS 64 - bit or 32-bit OS (win7)? what OS would you use if you were me?

  Thank you.

  Hey Buddy,

  1 + 2. I think everything is related to a higher internal temperature and you must clean your laptop using a jet of compressed air. That is why it s not necessary to remove, just blow softly and soon the air through the laptop. You can buy such compressed air which squirts of each computer store I think and it takes only 5 minutes.
  You can find a useful article about this here:

  3. in my opinion he should forget this update! The speed of the RAM is related to the FSB of the CPU and as much as I know about Satellite U405D it s 667 MHz so it s already the RAM faster than you can have. Save your money and buy a larger HARD drive or in the best case a SSD that can really improve the performance!

  4. in my view, the answer is clear: Windows 7 64-bit.
  Only a 64-bit OS supports full 4 GB of RAM. ;)

• Ask questions about the functionality of EA8500 MU-MIMO

  Dear Linksys

  I bought EA8500, and it arrived today.

  I have two questions about the functionality of MU-MIMO of EA8500 AP.

  1. I want to compare the performance between SU-MIMO and MU-MIMO, but there is no option to control this feature in the router admin page. Is that one of the possible ways?

  2 EA8500 supports 1733 Mbps wireless speed, but it resembles the speed of 1 Gbps ethernet cable.

  This router supports really speed 1 Gbps ethernet? or y at - it an option to support more throughput as the aggregation of links?

  Thank you

  Hi, hyeonu. For your first query, it is not possible because there is no option to disable the feature of MU-MIMO on your Linksys EA8500 router. In addition, with regard to your second, you can get a higher throughput of 1 Gbps since this is the maximum capacity of your ethernet connection.

• Question about RAM CL

  Hi guys. I'm finalizing my PC build and I have a question about ram CL I can't find answers for hackers page here. http://ppbm7.com/index.php/news/planning?showall= & start = 3

  I would use these two RAM sticks for example.

  Module 240 pin DDR3-1333 transcend JetRam™ 8 GB High Performance: CL9, layer 6 circuit board

  Transcend JetRam™ High - Performance 8 GB DDR3-1600 240-Pin Module: CL11, 6 layer PCB, ultimate card stability and cross-platform compatibility

  My question is, what is the best for video editing? On the one hand we have 1333 mhz to with a CL of 9. On the other hand, we have RAM 1600 mhz faster, but at a higher CL of 11. Now, I'm not one to get caught up in the technical aspects as it may seem, but I don't understand so I can make decisions, especially when price is a factor. In this case however, they are at the same price...
  

  Well good for video editing, important criteria for RAM is:

  • Never, never crashes - it is very important; choose only RAM sticks (certified QVL) certified provider and do not use unmatched sticks
  • Speed; faster is better - while true also, past at the speed of the RAM, or lowering of the CASE wait cycles (latency) contribute to the speed, but the gains are very low; Faster RAM is hardly perceptible vs CPU speed more fast which is very sensitive (I played with it a lot on some versions overclock and test first with PPBM speed and speed up the processor 5% performance contributes to 5% where speed RAM about 30% can speed up about 1%)

  Google "what is the CASE for the RAM" and one week at self-teaching yourself if you want to even begin to really understand speed RAM! I know enough to know there is a lot to learn about the subject. The good news is that you don't need really to know a lot to build a reliable, excellent for running Adobe products, including the first, Photoshop and After Effects:

  • Use only RAM who has certified the seller of memory for your motherboard; do not assume that if the seller indicates a set 4x8Go of sticks that will work with your motherboard that two sets of such RAM will work with a card mother 8 locations either! (too late to discuss here, but various factors may override the controller memory in the processor itself - factors include voltage RAM, number of sticks, RAM clock, status of CASE of waiting settings speed, voltage of the cpu memory controller and maybe more)
  • Increasing the speed of the RAM always helps if slightly for first speed up to 1600 MHz (for x 79 in any case) and wins the speed of RAM which are still lighter

  Now, back to why both sets of sticks are the same cost. They most likely use the same chips of RAM, which is an important factor for what it costs to build the RAM sticks. While the Asus motherboard you buy allows full customization of many, many, many things, unless you are an extreme Overclocker and plan to spend a few weeks to fine-tune a new simple version you in the bios of motherboard and it say to use XMP settings. This indicates the motherboard, how to set the speed of the RAM and sticks of timings CASE for your particular RAM with the settings the seller intended.

  You really know a lot about what you are doing to set the timings RAM in any way other than the simple choice of XMP settings safely. And, you can easily burn your CPU if you don't know what you're doing and you choose some really bad parameters.

  Kind regards

  Jim

• Questions about the export of PDF with India CS5.5

  Hey all,.

  A few questions about the export to PDF of the most recent version of India.

  First of all, I noticed it seems to take much more time to access a PDF file. Any suggestions about how to speed up the process? It took 8 minutes to generate a PDF low resolution (for printing) of a document of 24pp with placed images and vector graphics. Wow, that's a long wait, especially for evidence.

  Second, the background task... If I get it will make this PDF of 8 minutes and then more work on the document, which is exactly in the PDF? Usually, I have save before making a PDF or printing. Thus, the latest version is saved which will be in the PDF?

  (Either incidentally, this ability to work on the doc while generating a PDF file seems kind of weird. Generally, we do a PDF for proofing, or even for printing, when any changes have been made and that everything is "final". Therefore, I see no advantage in being able to work on my document while it is making a PDF file, I am probably once your revisions for the moment. I must say that I like the progress bar that you get when you perform an interactive PDF, as you know that you can not work on the document when it is on the screen...)

  Thank you as always.

  Good, people. Wanted to just follow this and post my results. It turns out that the problem is somewhere in the Illustrator file. I never had the time to guess what work plan was the culprit. Other India files PDF files is transparent and not a lot of time.

  No resolution, unfortunately, just good to know that it is not all India files on my system. Phew!

  THANK YOU for your advice.

• Where can I ask a handful of general order questions about Firefox OS as a consumer and get the answers? (a forum or something similar)

  I have about seven questions about Firefox OS. I'm potentially interested in opting for a tablet that works instead of Android or iOS. I couldn't find a place to ask questions like that. Thank you!

  https://support.Mozilla.org/en-us/forums/Firefox-OS-English-Forum

  There is another option.

• About a month ago I posted a question about iMovie and not being able to "share". I solved the problem thanks, so no more emails!

  About a month ago I posted a question about iMovie and not being able to "share". I solved the problem thanks, so no more emails!

  Hi Michael,

  If you want to stop receiving notifications by electronic mail, in the thread, that you have created, then I suggest that you follow the steps below:

  One time connected to the Apple Support communities, visit your mini profile and select manage subscriptions.

  

  Content

  To manage this content, you are currently subscribed and changing your preferences, select the content.

  Select next to see what content you are currently following.  Note that any thread you are responding you subscribe you automatically to this thread.

  You can select to terminate a subscription to a thread.

  

  Learn how to manage your subscriptions

  Take care.

• Where and how do I ask questions about Email?

  The Commission opening thingy is complicated, I have trouble finding my way around it.  I don't know where or how questions about email.  Is there an easier way than trawling through all these icons?  Like a list or something - as you get on all other forums on the internet?

  It would be a good starting point: Mac mini

  Or the appropriate under MAC Os and system software section.

  You might also find this useful: find answers and new questions

• Many questions about the HP 50 g

  I just ordered a HP 50 g graphic calculator! I have a few questions about this so hang on tight! What is the USB connector on the calculator? Mini-USB, micro USB, or is it a connector owner, "custom". Then, it would be possible to connect a keyboard to the HP 50 g by using the USB Port? Is there a program that would make this possible? (I doubt it would work if you plug it..) I have a Mini-USB to female USB 2.0 connector. So I could just plug the keyboard right, provided that the port on the calculator is a Mini-USB Port. If this is not so that I could use my female to female USB adaptor to connect the keyboard.

  Thanks for your help,

  Zekelegge

  Hi!, zekelegge:

  Welcome to Forum!

  The only printer I use, 50G calculators, 48GII, 39GS and 17BII +, as well as many former models, such as the 48 s/SX/G/G + / GX, 38 G, 39 G, 42, 41 C/CV/CX and 28 C/S, is the infrared printer HP 82240 b. If you can use the emulator HP50G, on the PC, the simulator of the printer, you can download, since... http://www.HPCalc.org/details.php?id=7386

  The printer... HP 82240 B

  

  The cable series...

  

  The description... http://www.allenwan.com/hpcalcserialcable/

  The original cable...

  

• Question about warranty after exchanges of RAM on Satellite module series

  Hello together,

  I have a question about the warranty. My laptop is 5 months old and now I want to improve it with more RAM. I want to do it myself, and now I'm wondering if the warranty will be getting hurt.
  Thanks in advance for your answers.

  Concerning

  TiG3r

  For new models of laptops the RAM upgrade described in s operating manuals. It is public act and it shows the owner of the notebook how do RAM upgrade only.

  If Toshiba offers something like this he won't have the negative influence of valid warranty.
  Buy a compatible module and RAM upgrade.

  Bye and good luck!

• A few quick questions about the Satellite P300 - 18 M

  Hello

  I am about to order a Satellite P300 - 18 M and have just a few questions about this:

  (Although these may apply for other similar Satellite/Equium P300.)

  Is the touchpad made by / to use the Alps or Synaptics driver?

  It has the Wireless N network card, is the map made by Intel or Realtec?

  And also, someone has experience with face recognition software to connect?

  If so, does it take a lot of time to initalise?

  Thanks in advance,
  Jack

  Hello

  The P300 - 18M belongs to the PSPCCE series.
  It uses the two touchpad drivers. Synaptics & Alps Electric
  There is an Intel 802.11agn minicards WLan installed

  The face recognition is a nice tool but local to be illuminated and you must take your face the right of the post sometimes it of not very easy

  But if you face is recognized correctly that the connection should work properly

  See you soon

• Questions about nb200

  I recently bought a mini nb200 with windows 7 and I have a few questions about it. How can you set up your email, I was willing to put up with Outlook Express, but I don't know if I can. Also, is there a way to get a paper copy of the user manual?

  You can download and install a new e-mail program when you download Windows Live via Microsoft Update. You can select the components of Windows Live, you want to include by checking a box for each you want. I installed all the. Or you can use Outlook, if you have Microsoft Office and you want to install it.

• A few questions about the difference between the Satellite P70, L70, S70

  Hello, I have a lot of questions about the P70, L70, S70 series that come with a 1920 x 1080 panel.

  (1) what are the differences between the L70 and S70 series? With the exception of the RAM and HARD drive capacity, books seem pretty identical.

  (2) P70, L70, S70 doesn't support a 2nd HARD drive or it's just the P70 series that support?

  (3) all the three (P70, L70, S70 series) come with the same TFT panels?

  (4) of the above series, which supports mSata?

  (5) all the model of each series are delivered with support from mSata? For example, it could be that L70 - a - 13 m supports mSata is not the case of the L70-a-146?

  (6) all the foregoing, are delivered with a S - ATA II or III S - ATA interface?

  (7) who is the best of these series listed? I'm trying to understand what makes the big difference of S70 to P70 except for the envelope for example.

  Thank you in advance.

  > (1) what are the differences between the series L70 and S70? With the exception of the RAM and HARD drive capacity, books seem pretty identical.

  What models Sat L70 and S70 do you mean exactly? There are different L70-xxx-xxx and S70 models on the market that supports different hardware specifications.

  (> S70 2) P70, L70, support a 2nd drive HARD or is - it just the series P70 that support?
  As you can see in this [Sam P70 HDD replacement document, | http://aps2.toshiba-tro.de/kb0/CRU3903II0000R01.htm] the P70 series supports the 2nd drive Bay HARD, BUT even if there is a 2nd HARD drive Bay, this does not mean that you can use the 2nd HARD drive. In the case where the 2nd HARD drive Bay are equipped with HARD drive connector, you can use the 2nd HARD drive

  I also found the [Sam L70/S70 HDD replacement | http://aps2.toshiba-tro.de/kb0/CRU3703HG0000R01.htm] the document on the Toshiba page and there I see this 2nd HARD drive Bay is not available

  (> 3) all three (P70, L70, S70 series) come with the same TFT panels?
  See point 1). Different P70, L70, S70 models were equipped with different material parts.

  (> 4) of the series above, which takes in charge mSata?
  As far as I know that some P70 models are equipped with an mSATA SSD of 256 GB.

  (> 5) do all the model of each series are delivered with support mSata? For example, it could be that L70 - a - 13 m supports mSata is not the case of the L70-a-146?
  See point 4) not all models supports the same hardware specifications

  (> 6) all of the above, come with a S - ATA II or III S - ATA interface?
  I don t think that SATA III is supported. I guess it would be SATA II

  (> 7) which is the best of these series listed? I'm trying to understand what makes the big difference of S70 to P70 except for the envelope for example.
  Not easy to answer because there are too many models released in Europea.
  And not all models are available in each country. So I guess you will have to look for the models that have been released in your country.