Question: BDP-S570 or BX57 internet multi-channel flow?

Similar Questions

• BDP-S570 and SACD

  Hi, I'm new on this forum, but long-time Sony fan and supporter. I recently bought a new Sony BDP-S570 BD player to go with my old Philips 32 '' LCD HDTV, the new Sony KDL-46HX800 3D TV and the STR-DA4600ES receiver. I have also several audio SACD discs I wanted to play with this configuration.
  Here's the problem I have:
  I currently have my receiver output HDMI connected to my HDMI TV Philips entry. I have my BDP-S570 connected to the Sony STR-DA4600ES HDMI4 entered. I put the BDP-S570 to output SACD PCM since this receiver that I discovered after I bought it does not support the SACD DSD decoding. Anyway, in PCM mode when I try to play any disc SACD, I see video playback on the TV screen, but there is no audio output. If I put the drive to play only tracks CD (as opposed to the SACD titles) of the disc, then it plays audio in stereo via the PCM mode very well.
  I narrowed down it to her get to play SACD by disconnecting the HDMI TV to receiver connection. If I remove the connection HDMI to the TV, the BDP-S570 SACD multichannel audio stream to the receiver. If I turn on the TV the audio stream disappears again. If I connect the player to a compatible old receiver from Onkyo NR-905 HDMI 1. 3A, she plays SACD audio fine even with connected HDMI TV. So it seems to be a bug in signaling of handshake in my Sony (receiver and BD player) components.
  Sony support, please have your engineers check this aspect of the game of the SACD through your own line of Sony STR-DA4600ES of receivers with an old connected HDMI TV. It simply doesn't get it!
  Sorry for the long-winded post but no other way to describe the details of my configuration to explain it all. Is there a fix in the works for more reliable SACD playback on this player BD BDP-S570 3D? Oh, BTW, I installed the latest firmware update from 13/02/2011 or there abouts. Receiver was last updated available also new out of the box. Please tell me Sony is concerned and is looking to fix this incompatibility in the next version of the firmware! Thank you!

  I just update my situation with this problem of reading SACD I posted. I see nobody else was interested, but I'll post my resolution and conclusions.

  I got my BDP-S570 to play multi-channel SACD through my receiver STR-DA4600ES now by removing a HDMI switch which is connected between a video output HDMI to my receiver and my TV HDMI input jacks. It's the HDMI switch which was somehow not the right signals to the system causing the BD drive to not stream of SACD PCM signals to the receiver. As soon as I removed this switch HDMI from the signal path, it al started to work and read its SACD via the receiver.

  Also, I just noticed that the BDP-S570 is streaming music network in multichannel format now on Pandora music! I never saw blue light multichannel light upward when streaming music on the internet before. I don't know if it is also a symptom of the switch HDMI sending bad communications signals to the player OR if there is a change in the last update of the firmware that I installed on my BDP-S570. It's streaming multi-channel music on Pandora as I type this post!

  Update: I think the BD drive his downmix PCM multi-channel had put instead if 2-channel PCM. If this can explain why I see multichannel streams now too and has not seen him before. HDMI switch issue was also this masking of screening until previously I suspect. Now with HDMI switch out of the picture, it appears as a multi-channel as it supposed to.

  Update2: Well I just tried to change the setting to "DownMix" multichannel stereo PCM BD drive. Then I turned off the BD drive and turned back on to ensure that it restores its settings. I pulled to the top of the current internet music and video broadcasts and guess what? The Sony receiver is always get a stream PCM multi-channel (surround sound)! So it isn't the "DownMix" setting, which is the only cause. Apparently after I loaded the last firmware for this player, it plays now all this internet stream (music and video sites shows) in Multchannel surround sound mode.

  Update: too bad people, I found my answer. The cause of constantly multichannel PCM streaming of all my network connections was because I had the BDP-S570 DTS parameter defined on ' Neo: 6 Music ' instead of 'Off' in the settings menu. I set this to "off" and all the music from the internet is now back to regular 2-channel flows. for info. case solved.

• Cannot create the multi channels Tx two USRP-2943Rs Session with driver

  I have problems of implementation of several USRP-2943R devices in tranmist both of their channels at once.  Right now my configuration is a configuration of four chains composed of two devices of RIO.  I am only able to transmit at the same time successfully CH0 and CH1.  I'm creating a session using two devices and my aim is to perform Tx on CH0 via CH3.  In addition, my goal is to use the LabVIEW driver without any synchronization, because I test fix synchronization through post-processing and you want the VI be as simple as possible without the hassle of FPGA programming. I realize has the Simple models OR - USRP Streaming Sync in LabVIEW, but additional synchronization and FPGA programming is too much for such a simple project like mine which would require no synchronization USRP.

  My VI and some screenshots of the error messages resulting is attached.  I am able to succesfully implement multi-channel Rx deals and attached is my multichannel Rx VI.  My question is why I can open and operate a session of Rx mult-channel without problem, while a multi-channel Tx session will give me errors?

  My final goal is to merge my multichannel work Rx VI with a mult-channel Tx VI work for measurements in order to test some synchronization post-processing routines that are performed in Matlab.

  I think that I found a solution to my problem.  I thought to post it here to help others.  It is important to use some sort of device to synchronize several USRPs.  However. I found that you must reset the device by setting the node of reset function blocks that open and session Rx or Tx.  "" If it is not defined, then the ' niUSRP Signal.vi configurethe ID of the specified attribute is not valid for the scope specified (or channel)." error occurs, any circuits that you define.  After the node Reset true and place an empty string for my channels Enabled, all was fine.  Also, a full duplex system you will be only to first log of Rx with a reset of the device, followed by the opening of a session of Tx without a reset of the device.

  One more thing, it is that there seems to be a bug if you feed a Tx process a table whose number of lines does not match the number of channels Tx.  This will result in weird errors funny will disappear only after doing a hard reset of the units.  So, just something to take note of.

  I hope this information will help others and this message can be marked as resolved.

• BDP-S570 not out of HD audio formats

  I have audio output with my BDP-S570 problems. BluRay connected to the Denon AVR-1911, through cable high speed HDMI. Denon then connected to Bravia KDL-55HX800 through same cables. 3D video works fine but I'm not getting any outputs audio TrueHD or DTS HD and not even get regular Dolby incidentally. Output on just says Denon Multi Ch. I have a PS3 connected to the Denon even with the same cables and output HD audio very well. I realize that I can just use the PS3 for the same use but still need to understand this problem. I have read a lot into that and have fooled with several settings, but nothing seems to work. Am I missing something simple? Any help is greatly appreciated.

  Figured it out. Just in case anyone has the same problem, you have to set Off BD Audio Mix. (Mix = is the default.) When the mixture is turned on, the player decodes and output multichannel PCM. Now I get the DTS HD and the sound is incredible.

• Simultaneous multi-channel Imaging NI PCI-1422 or 1424?

  We have an IMAQ 1408. We want to make simultaneous multi-channel imagery. However, 1408 has only 1 A/D converter, it cannot acquire multiple channels simultaneously. We are looking for possible upgrade.

  The NI PCI-1422 or 1424 seem to upgrade products of 1408. Can someone tell us if they can do simultaneous multi-channel Imaging?

  Sorry if this isn't the right forum for me to post this question. But I called the customer service OR. The guy doesn't really know acquisition cards. I think that there are more experts here.

  If you have analog signals, it is a little more difficult.  NEITHER ensures more hardware to read signals from analog cameras.  I don't remember all of their equipment, be capable of more of an analog input signal simultaneously.  They always alternate between the signals, a reading at the same time frame.

  Your best bet would be to get an analogue to digital converter which converts the formats I've mentioned.  You must make sure it is compatible (uncompressed, industry standard, etc.).

  Bruce

• BDP-S570 not stream 5.1

  I am unable to stream digital Dolby 5.1 on NetFlix or Amazon.  I re - configure the audio settings and the audio still come as a Pro Logic.  DVD and BluRay discs work very well (DD or DTS) and Pandora plays music as PCM 44.1.

  NetFlix thinks I must throw my BDP-S570 and buy a new one.

  If this can be true?

  Apparently, the Dolby Digital 5.1 is not available when you play movies netflix on this unit. For amazon, you may have to contact them to see if they allow the DD 5.1 surround sound on the Blu - ray player.

  If my post answered your question, please mark it as "accept as a Solution.

• How can I get multi channel audio via the HDMI port on an early 2015 MacBook Pro?

  I try to get the 7.1 audio channels to flow from my MacBook Pro to a cinema set up. The display works fine now I plug the HDMI in however the sound still Mac speakers. I checked the settings and no HDMI output is available. An airtime option is available, but that returns only two channels as a maximum to the receiver. When I go to the configuration of the source on the receiver it receives video at 1080 p 60herts however it is specifically stated No Audio from the Source.

  Also, I have connected my iPhone 6 s more using an Apple through the same HDMI cable adapter and it works perfectly. We also use HDMI with our PS4 occasionally and it works perfectly, even with the 3D.

  Thus, the MacBook Pro is early 2015 with an i5, the receiver is a Harmon Kardon AVR 2700 (we run 7.1 channels of this) and we are connecting via the HDMI port through a 50 ft HDMI before. The receiver sends the audio to a projector with 1080 p 60 hertz if it changes anything...

  Also if it helps the receiver supports dts - hd master audio decoding, Dolby True HD/Digital Plus decoding, HDMI 1.4 (HDMI is compatible 2.0), as well as multi-channel input and PCM and linear PCM.

  I use a "Behringer UCA202' audio device I bought on amazon.com for only $29.

  It works very well for the audio 5.1 or 7.2. Works connect optical toslink. Just plug it into a usb port on your Mac and a cable optical toslink to your AV receiver.

  My Yahmaha 7.2 audio/video receiver is measuring process the digital signal in THX, DTS, Dolby digital Pro logic, a cinema, etc.

  

• AI trigger and measure multi channels

  Hi all

  I have a simple problem (using USB-6259).

  can repeat the measurement trigger of AI and measure multi channels, but not both at the same time.

  -DAQmxCreateAIVoltageChan(hd, "DEV1/ai0",...)                    define the ai0 as the trigger channel

  -DAQmxCfgSampClkTiming

  -DAQmxCfgAnlgEdgeRefTrig

  -DAQmxStartTask

  -DAQmxReadAnalogF64 (hd, "DEV / ai0:3 ', / / I want to measure more channels"ai0:3"not just"ai0")

  Thank you

  Hassan

  Hi Hassan,.

  If you use an analog trigger with several analog channels, you will need to use the APFI0 input as source of relaxation. See this KB: Why do I get error-200264 when running analog reference trigger? All you need to do is to connect your analog signal online 0 to APFI0 (Paperback 20 in your case) and set the source of relaxation at APFI0.

  The reason is that you don't have that an NOC on Board (series E or M) and she's going to have to switch between the different lines (see this KB: modes of sampling). This parameter collides with the idea of a trigger analog reference on a specific line (constant sampling of data in a ring buffer up to what a condition is met). The APFI0 line, however, has its own CDA. Therefore, it can run simultaneously.

  However, please note that the ADC is fast but has lower resolution to HAVE it sampling ADC. See these KBs: series E and M series Analog Input Trigger resolution, be aware of a possible error between the analog trigger threshold and the value of the first sample

  Hope this clarified the issue.

  Best regards

  Peter

• Imaging multi channels using the acquisition card OR

  We have a 1408 IMAQ being controlled by LabVIEW 8.0.

  We want to install multi-channel of imagery. All the channels work individually. However, when I was trying to show two channels simultaneously, single channel works and I got the following error message:

  Error 1074397150 has occurred to IMAQ enter Setup.vi

  Possible reasons:

  NOR-IMAQ: A timeout error occurred while you wait for the specified event. If you expect a picture, make sure all the video data is acquired during the period. If you wait for a signal, check that the assertion of signal occurs within the period.

  Sometimes I get a different error message asking me to assign different buffers to both channels. I understand that IMAQ 1408 has only analog digital (ADC) converter to digitize the incoming video. It may acquire up to four different cameras, but only of a camera at a time.

  I don't mind do frame rate in half. I think to show only one channel at a time and do the two channels alternantly. But I need to know how config routes to get there.

  I've attached an example that should work.  I could not test it because I don't have the equipment, so it might need some settings.  I would test it with one channel by setting the channel # 1.  Once it works, define channels # 2.  I set the display to use snapshot mode so the same image can be used for all screens.

  The only reason that I can think of that would make multi-channel acquisition fail when single channel works is the lack of synchronization between signals.  The start of frame signal must be the same for all channels.

  Bruce

• Cannot get DTS/multi channel audio via HDMI

  Hello
  I'm trying to connect my VAIO SVT15112CXS to my Bravia HDTV via HDMI to get multi-channel audio (DTS/DD) from my Bravia HT (connected to the TV via optical) with no luck at all.

  I have the same setup for PS3 works well, is it cable or equipment.

  I have already updated all the drivers.

  When the TV is not connected I don't get an Audio HDMI option in the playback devices (I checked to show disconnected devices / disabled) and when it is connected I do not get an option to change the configuration of stereo speaker.

  This way I get only Stereo sound.

  I tried passthough HDMI via ffdshow config (installed K-Lite codec pack) and there is no sound in this way.

  Is there a solution? something escapes me?

  Thanks to all in advance,

  Thanks for your time and your response.

  I got it actually work! updated drivers audio and video (not Sony ones sugested, but later of Intel and Realtek) and now I have everything works as it should.

  The only minor problem is that Vaio Care now wants me to go back to the previous version of the driver, but I'll just ignore it.

  Everyone, try this if you experience this problem.

• Multi-channel acquisition - simultaneous Acquisition of sampling 1 & 2-channel single sample in a task

  I am able to get a multichannel simultaneous sampling on my acquisition of data (USB-6363) without problem. But what I want to do is make multi-channel acquisition in a single task where sampling requirements are different for each channel. For example, I want I want to acquire a total of 1000 samples on 3 channels in a single task with DAQmx as follows the characteristics of sample:

  • AI0: Analog Wfm 1Chan NSamp (998 samples)
  • AI1 + ai2: 1 d analog NChan DBL 1Samp (1 + 1 sample/channel)

  I know I could do just a regular multiple sampling multi-channel acquisition through all three channels then average down from channels 1 + 2, but I don't have that several samples to spare. AI0 is a bandwidth hog in my application and consumes all the samples of data acquisition (2. MECH / s), but I can save a few samples to make analog measurements further (for example, temperature, pressure).

  Ai0 takes place also permanently so additional analog measures on ai1 + ai2 need to be included in the same task.

  I don't know how to go on this matter or if it is still possible. Any ideas or thoughts would be greatly appreciated.

  Currently I use a second DAQ to read these additional channels at a lower rate but I need to pass a single data acquisition.

  How should continuous ai0 really be?  You of course can enjoy on ai0, and one of the other entries at the same time, then there would be some gap in your data.  In addition, if you want to go to the full 2 MHz, you may sample ai1 ai2 twice in order to allow entry to set (the maximum specified multi-channel rate is only 1 MHz due to compaction of the constraints on the MUX I believe).

  DAQmx sort of you lets set something up like that, if you "cheat" it by configuring each sample as a single channel in your task (see an example similar here).  If your 998 + 1 + 1 (or 996 + 2 + 2) becomes a task of channel 1000 (takes a bit more memory, but should still be feasible).

  I would consider a 2nd DAQ card a better option if ai0 really needs to be continuous.  You can go with a (9174 or 9178) cDAQ chassis a 9223 (only 1 MHz if) for quick entry and your choice of module for the slower entries.  On the cDAQ chassis a module can run a separate task of AI from other modules (up to 3 tasks HAVE by chassis) at different speeds.

  Best regards

• I'm trying to export multi-channel audio as apple pro res 422 HQ, but the tracks are all coming full joint rather than separately. I've implemented the multi Channel sequence already. What I am doing wrong?

  I'm trying to export multi-channel audio as apple pro res 422 HQ, but the tracks are all coming full joint rather than separately. I've implemented the multi Channel sequence already. What I am doing wrong?

  All 4 titles are coming as complete blends not divisions. I guess that's a problem with the entrenchment of the channels, but can't see how to fix. Andy

  Is what would you say to my quick thought without following through all the processes after the fact, the sequence settings? My thought is that the sequence settings must be multichannel as you show, but each Adaptive track, so this channel map is routed at your leisure. If this is not the case, already, it would create a new sequence with these settings.

  I try to upload the photo

  

• BDP-S570 - does not connect to internet via wifi

  I just bought this today and it does not connect to the internet via wi - fi. I'm entering properly (my iphone, ipad and computers connect very well). I called tech support and they had no idea what either. I then connected with an ethernet cable, updated to the latest firmware and tried again with no luck. Does anyone have any suggestions? It shows that the wireless is OK, but Internet Access - failed. When I return to the guests and have it analyzed the available networks, it shows that I am connected... something is weird. I'm back if I can't make it work in the next day or so.

  Network problems can certainly be difficult to diagnose.
  Here are some useful steps to check where your problem is.

  Check the IP address: is it 192.168.x.xx? or 169.xxx.x.xx
  If you have an address 169 it is a fake connect.

  What kind of network do you have? It's a Modem/Router combo? This is a modem connected to a router and then your Blu - ray player.

  the router/Modem combos are more complicated, and you need to consult your provider of Internet services (ISP) to connect to help. (maybe a MAC filtering problem?)

  If you have a problem with your Modem/Router try get a router and connect to the modem, you can have the best success with a stand-alone router you will have with a handset as they are less complicated to use.
  If you already use a stand alone, try to temporarily disable your security and test it without warranty.

  is the firmware updated on your router (not the S70 but the router) the latest firmware is sometimes useful.

  Best regards
  Kimberly

• Question about multi-channel information

  Hello I am trying to get a CSV file with some information on the paths with this script:

  $lunpathinfo = @ () $esxName = "My_HostName" $vmhost = Get-VMHost-name $esxName = get-view $hostview $vmhost.id $hostview.config.storagedevice.multipathinfo.lun | % {' $lunname = $_.id = $lunpolicy $_.policy.policy $_.path | % {$pathstate = $_.pathstate $lunpathinfo += "' |}} {Select @{name = "Hostname"; expression = {$vmhost.name}}, @{name = "LunName"; expression = {$lunname}}, @{name = "LunPolicy"; expression = {$lunpolicy}}, @{name = "PathState"; expression = {$pathstate}}} $lunpathinfo | Export-csv Q:\POWERCLI\Out.csv

  I see that "$hostview.config.storagedevice.multipathinfo.lun" information like:

  Key: key - vim.host.MultipathInfo.LogicalUnit - 02001 a 000060060

  e800565540000006554000000b74f50454e2d56

  ID: 02001a000060060e800565540000006554000000b74f50454e2d56

  Mon: key - vim.host.ScsiDisk - 02001a000060060e8005655400000065

  54000000b74f50454e2d56

  Path: {fc.20000090fa6a8950:10000090fa6a8950 - fc.50060e8005655}

  461:50060e8005655461 - naa.60060e80056554000000655400000

  0 b 7, fc.20000090fa6a711e:10000090fa6a711e - fc.50060e800

  5655470:50060e8005655470 - naa.60060e8005655400000065540

  b 00000, 7}

  Policy: VMware.Vim.HostMultipathInfoFixedLogicalUnitPolicy

  StorageArrayTypePolicy: VMware.Vim.HostMultipathInfoLogicalUnitStorageArrayTyp

  ePolicy

  DynamicType:

  DynamicProperty:

  And I want to extract file CSV, the path information (fc.2000...) but I can't. Is it possible?

  Thank you very much

  Try like this

  $lunpathinfo = @)

  $esxName = "My_HostName".

  $vmhost = get-VMHost-name $esxName

  # $hostview = get-view $vmhost.id

  $vmhost. ExtensionData.config.storagedevice.multipathinfo.lun | % { `

  $lunname = $_.id

  $lunpolicy = $_.policy.policy

  $_.path | % {

  $pathstate = $_.pathstate

  $pathName = $_. Name

  $lunpathinfo += ' | Select @{name = "Hostname"; expression = {$vmhost.name}}.

  @{name = "LunName"; expression = {$lunname}},

  @{name = "LunPolicy"; expression = {$lunpolicy}},

  @{N = "Path"; E = {$pathName}},

  @{name = "PathState"; expression = {$pathstate}}

  }

  }

  $lunpathinfo | Export-csv Q:\POWERCLI\Out.csv

• How to view Windows Media Center Internet TV channels streaming?

  So I set up Windows Media Center and I was wondering... is it possible to see the free internet channels on WMC instead of Internet Explorer? I have ben trying to find info on this. Apparently some people have been able to do, but the info, I had about six years ago. I am only able to get HSN only. Is it possible to see if I can look at others?

  So I set up Windows Media Center and I was wondering... is it possible to see the free internet channels on WMC instead of Internet Explorer? I have ben trying to find info on this. Apparently some people have been able to do, but the info, I had about six years ago. I am only able to get HSN only. Is it possible to see if I can look at others?

  Microsoft abandoned Internet TV for Windows Media Center in September 2012. So you will need to use IE.

  --
  Barb

  MVP Windows Entertainment and connected home

  My Blog - http://digitalmediaphile.com/

  Connected world Blog Reader Windows 8 App Barb-
  http://apps.Microsoft.com/Windows/en-us/app/barbs-connected-world-blog/02f35769-52bf-461C-b1d5-06e54a58d298

  Windows and Surface drive Windows 8 App community
  http://apps.Microsoft.com/Windows/en-us/app/Windows-and-surface-community/0abb150e-D287-47d4-837E-9fa51f485ad7

  Please mark as answer if that answers your question