Question VPN on Cisco 7206
Hi Experts,
We have a VPN configuration between a Cisco 871 router and a Cisco 7206 VXR router.
The 7206 is a location of the hub and the 871 is one of the rays.
The 871 uses a DSL connection to connect to the internet.
Today we receive a large amount of newspapers on the 7206, newspapers are as below-
14 Dec 17:47:48.326 is: % CRYPTO-4-IKMP_BAD_MESSAGE:
14 Dec 17:48:57.078 is: % CRYPTO-4-IKMP_BAD_MESSAGE:
14 Dec 17:50:33.191 is: % CRYPTO-4-IKMP_BAD_MESSAGE:
14 Dec 17:51:47.383 is: % CRYPTO-4-IKMP_BAD_MESSAGE:
Can someone advise if there may be a problem with the DSL connection or if it means something else. Hi Imran Looking at the error message, the keys of encryption on both ends do not match. Make sure that the pre-shared keys are configured correctly Cordially MJ Tags: Cisco Security remote VPN does not work on Cisco 7206 Hello I do a test to set up remote access to VPN from Cisco 7206 (simulated by dynamips). The relevant configuration is the following: hub host name AAA new-model AAA authentication login local xauth username ciscouser password 0 cisco1234 IP subnet zero crypto ISAKMP policy 10 md5 hash Group 2 preshared authentication test group crypto isakmp client configuration key cisco123 pool mypool card crypto REMOTEACCESS client authentication list xauth Crypto ipsec transform-set RTP-TRANSFORMATION des-esp esp-md5-hmac Vpn crypto dynamic-map 1 game of transformation-RTP-TRANSFORM open crypto map REMOTEACCESS client configuration address card crypto client configuration address respond REMOTEACCESS card crypto REMOTEACCESS 1-isakmp dynamic vpn ipsec interface Ethernet0/0 IP address 150.1.1.1 255.255.255.0 card crypto REMOTEACCESS interface Ethernet0/1 IP 11.10.1.1 255.255.255.0 no ip directed broadcast to the IP local pool mypool 10.1.10.0 10.1.10.254 IP nat translation timeout never IP nat translation tcp-timeout never IP nat translation udp timeout never IP nat translation finrst-timeout never IP nat translation syn-timeout never IP nat translation dns-timeout never IP nat translation icmp timeout never IP classless IP route 0.0.0.0 0.0.0.0 10.103.1.1 no ip address of the http server end However, when I try to connect the router using the Cisco 4.6 client, you receive the following error message: 05:04:52: ISAKMP (0:1): audit ISAKMP transform 13 against the policy of priority 10 05:04:52: ISAKMP: DES-CBC encryption 05:04:52: ISAKMP: MD5 hash 05:04:52: ISAKMP: group by default 2 05:04:52: ISAKMP: auth XAUTHInitPreShared 05:04:52: ISAKMP: type of life in seconds 05:04:52: ISAKMP: life (IPV) 0x0 0 x 20 0xC4 0x9B 05:04:52: ISAKMP (0:1): pre-shared key offered Xauth authentication but does not match policy. 05:04:52: ISAKMP (0:1): atts are not acceptable. Next payload is 3 05:04:52: ISAKMP (0:1): audit ISAKMP transform 14 against the policy of priority 10 05:04:52: ISAKMP: DES-CBC encryption 05:04:52: ISAKMP: MD5 hash 05:04:52: ISAKMP: group by default 2 05:04:52: ISAKMP: pre-shared key auth 05:04:52: ISAKMP: type of life in seconds 05:04:52: ISAKMP: life (IPV) 0x0 0 x 20 0xC4 0x9B 05:04:52: ISAKMP (0:1): pre-shared authentication offered but does not match policy. 05:04:52: ISAKMP (0:1): atts are not acceptable. Next payload is 0 Does anyone have an idea? Thanks in advance. Wang, Thanks for the update! Happy in his work. The commands below are for the search for group policy. AAA authorization groupauthor LAN card crypto isakmp authorization list groupauthor REMOTEACCESS Since then, you have configured Group Policy (name, presharedkey, etc.) locally on the router, you must specify the router where to look for the isakmp policy when VPN cace tries to connect. I hope it helps. Kind regards Arul * Please note all useful messages *. Hello, I've been buying cisco 7206 and I smartnet for 7206 IOS for 7206 have bug howe can I download deployment general ios gor 7206 Hello With smartnet, you should be able to have a cco login account and go directly to the download software area Select the IOS software on the left side http://www.Cisco.com/Kobayashi/SW-Center/index.shtml Also on the same link above, if you do not have the ID of the bug you can go bug toolkit database and quary the ID of the bug to know exactly the code version it was fixed. If you have smarnet but don't have a cco login to access the download area, contact the Cisco TAC services http://www.Cisco.com/en/us/support/tsd_cisco_worldwide_contacts.html Rgds Jorge What VPN work as a PPTP vpn firewall CISCO-ASA-5520. Hi all Can you please tell me which replace the VPN I can configure PPTP on ASA 5520 firewall. What VPN work as a PPTP vpn firewall CISCO-ASA-5520. You can use the wizard VPN of RA with ASDM and confiugre L2TP IPSEC VPN that does not need a VPN Client must be installed. Michael Please note all useful posts SSL VPN on Cisco ISR G2 license 2921? Hi, quick question. We have a CISCO 2921/K9, who has all of the features securityk9 (reflects Permanent under show version) I thought including SSL VPN, but make a "show license all" it does not reflect that: J:: feature 4: SSL_VPN Version: 1.0 License type: EvalRightToUse The license status: Active, in use The total period of assessment: 8 weeks 4 days Assessment period left: 8 weeks 2 days Used period: 1 day 5 hours Transition date: 11 January 2013 23:05:41 Number of licenses: 100/0 (in-use/Violation) License priority: bass Can someone please provide some clarification? Thank you! -rya securityK9 does not include the SSL VPN license. This just activate the security features on the ISRG2, and you would need this license to run VPN SSL, and the SSL VPN itself license. Here is the URL for your reference: http://www.Cisco.com/en/us/docs/routers/access/sw_activation/SA_on_ISR.html#wp1151975 To run SSL VPN, you must securityK9 and SSL VPN license. Hello I'm trying to get my ipad to VPN to our Cisco ASA5520. I think I have all the correct settings on both ends (I am able to vpn to the asa using a cisco 871 as the remote client). I think that for some reason the client vpn on ipad is not even make the asa. My question is: How can I monitor the ASA logs to see if the same connection attempt and eventually find the failure? Thank you M try: -. Debug crypto ISAKMP Debug crypto ipsec Vpn-sessiondb SH remote control (to see if the client is connected) I have configured ipad for remote vpn client, the user could connect to the 5520 but why that I had to use the ip addresses to access, but I couldn't use internal dns names. try to understand that at this moment. It may be useful Manish IPSec VPN between Cisco ASA and Fortigate1000 Hello I find a useful document on how to create a tunnel VPN IPSec with ASA 5510 firewall Fortigate 1000... the configuration of the coast FG is done without any problem, BUT the document (. doc FG) said I must configure the ASA with a GRE interface and assign an internal IP address in order to communicate with the FG... The question is: How do I configure the interface on the SAA ACCORD? Thanks in advance, Experts... Kind regards... ASA firewall does not support the interface/GRE GRE tunnel. If you need to have GRE configured, you will need to complete the GRE tunnel on router IOS. If you want to configure just pure tunnel VPN IPSec (lan-to-lan), here is an example of configuration on the side of the ASA: http://www.Cisco.com/en/us/products/ps6120/products_configuration_example09186a0080950890.shtml Hope that helps. NAT before going on a VPN Tunnel Cisco ASA or SA520 I have a friend who asked me to try to help. We are established VPN site to site with a customer. Our camp is a Cisco sa520 and side there is a control point. The tunnel is up, we checked the phase 1 and 2 are good. The question is through the tunnel to traffic, our LAN ip address are private addresses 10.10.1.0/24 but the client says must have a public IP address for our local network in order to access that server on local network there. So, in all forums, I see that you cannot NAT before crossing the VPN tunnel, but our problem is that our site has only 6 assigned IP addresses and the comcast router, on the side of the firewall SA520 WAN. So we were wondering was there a way we can use the WAN on the SA520 interface or use another available 6 who were assigned to the NAT traffic and passes through the tunnel. That sounds confusing to you? Sorry, but it's rarely have I a customer say that I must have a public IP address on my side of the LAN. Now, I say this is a SA520 firewall, but if it is not possible to do with who he is a way were able with an ASA5505? Help or direction would be very useful. Hello I guess I could quickly write a basic configuration. Can't be sure I remember all correctly. But should be the biggest part of it. Some of the course settings may be different depending on the type of VPN L2L connection settings, you have chosen. Naturally, there are also a lot of the basic configuration which is not mentioned below. For example Information for parameters below Interfaces - Default - Access-list Route interface Vlan2 WAN description nameif outside security-level 0 Add IP x.x.x.x y.y.y.y Route outside 0.0.0.0 0.0.0.0 z.z.z.z interface Ethernet0 Description WAN access switchport access vlan 2 interface Vlan1 LAN description nameif inside security-level 100 10.10.1.0 add IP 255.255.255.0 Note to access the INSIDE-IN list allow all local network traffic access to the INTERIOR-IN ip 10.10.1.0 list allow 255.255.255.0 any group-access INTERIOR-IN in the interface inside Configuring NAT and VPN L2L - ASA 8.2 software and versions prior Global 1 interface (outside) NAT (inside) 1 10.10.1.0 255.255.255.0 Crypto ipsec transform-set AES-256 aes-256-esp esp-sha-hmac crypto ISAKMP policy 10 preshared authentication aes-256 encryption sha hash Group 2 lifetime 28800 L2L-VPN-CRYPTOMAP of the access list allow ip x.x.x.x a.a.a.a b.b.b.b host card crypto WAN-CRYPTOMAP 10 matches L2L-VPN-CRYPTOMAP address card crypto WAN-CRYPTOMAP 10 set peer c.c.c.c card crypto WAN-CRYPTOMAP 10 the value transform-set AES-256 card crypto WAN-CRYPTOMAP 10 set security-association second life 3600 CRYPTOMAP WAN interface card crypto outside crypto isakmp identity address crypto ISAKMP allow outside tunnel-group c.c.c.c type ipsec-l2l tunnel-group c.c.c.c ipsec-attributes pre-shared key, PSK NAT and VPN L2L - ASA 8.3 software configuration and after NAT source auto after (indoor, outdoor) dynamic one interface
Crypto ipsec transform-set ikev1 AES-256 aes-256-esp esp-sha-hmac IKEv1 crypto policy 10 preshared authentication aes-256 encryption sha hash Group 2 lifetime 28800 L2L-VPN-CRYPTOMAP of the access list allow ip x.x.x.x a.a.a.a b.b.b.b host card crypto WAN-CRYPTOMAP 10 matches L2L-VPN-CRYPTOMAP address card crypto WAN-CRYPTOMAP 10 set peer c.c.c.c card crypto WAN-CRYPTOMAP 10 set transform-set AES-256 ikev1 card crypto WAN-CRYPTOMAP 10 set security-association second life 3600 CRYPTOMAP WAN interface card crypto outside crypto isakmp identity address
Crypto ikev1 allow outside tunnel-group c.c.c.c type ipsec-l2l tunnel-group c.c.c.c ipsec-attributes IKEv1 pre-shared key, PSK I hope that the above information was useful please note if you found it useful If it boils down to the configuration of the connection with the ASA5505 and does not cut the above configuration, feel free to ask for more -Jouni Order SSL VPN with Cisco Cloud Web Security We have implemented Cisco Cloud Web Security with the connector of the ASA and transfer all traffic port 80 and 443 to the Tower of the CCW. We have enabled HTTPS inspection, and I was wondering if there was anything, we can add in the configuration that would allow us to control (allow/block) SSL VPN? #Clientless SSL VPN is not supported with Cloud Security Web; don't forget to exempt all SSL VPN traffic without client service ASA for Cloud Web Security Strategy. Reference: http://www.cisco.com/c/en/us/td/docs/security/asa/asa90/configuration/gu... Question of vlan Cisco 7600 PFD Hello! Please help with a question. In our network, we have 7600 and I need to create a service of vpls with two different VLAN associated with a PFD: L2 PFD manual test interface Vlan120 And when I try to reach "xconnect PFD testing: Incompatible with the PFD configured setting. Is it possible to do or not? No mapping VLANs etc. Thank you all! Hi Dimitri, you can do it, but the link is made to port vlan does not level level IVR. Here is a configuration snippet: the GigabitEthernet4/1/0 interface 101 ethernet service instance encapsulation dot1q 101 second 10 rewrite the penetration pop tag 2 symmetrical interface GigabitEthernet4/1/1 ethernet 100 service instance encapsulation dot1q 100 rewrite tag pop 1 symmetrical penetration connect GigabitEthernet4/1/0 eline-101 101 100 GigabitEthernet4/1/1 Xander ISA500 site by site ipsec VPN with Cisco IGR Hello I tried a VPN site by site work with Openswan and Cisco 2821 router configuration an Ipsec tunnel to site by site with Cisco 2821 and ISA550. But without success. my config for openswan, just FYI, maybe not importand for this problem installation of config protostack = netkey nat_traversal = yes virtual_private=%v4:10.0.0.0/8,%v4:192.168.0.0/16,%v4:172.16.0.0/12,%4:!$RIGHT_SUBNET nhelpers = 0 Conn rz1 IKEv2 = no type = tunnel left = % all leftsubnet=192.168.5.0/24 right =.
rightsourceip = 192.168.1.2 rightsubnet=192.168.1.0/24 Keylife 28800 = s ikelifetime 28800 = s keyingtries = 3 AUTH = esp ESP = aes128-sha1 KeyExchange = ike authby secret = start = auto IKE = aes128-sha1; modp1536 dpdaction = redΘmarrer dpddelay = 30 dpdtimeout = 60 PFS = No. aggrmode = no Config Cisco 2821 for dynamic dialin: crypto ISAKMP policy 1 BA aes sha hash preshared authentication Group 5 lifetime 28800 ! card crypto CMAP_1 1-isakmp dynamic ipsec DYNMAP_1 ! access-list 102 permit ip 192.168.1.0 0.0.0.255 192.168.5.0 0.0.0.255 ! Crypto ipsec transform-set ESP-AES-SHA1 esp - aes esp-sha-hmac crypto dynamic-map DYNMAP_1 1 game of transformation-ESP-AES-SHA1 match address 102 ! ISAKMP crypto key
ISAKMP crypto keepalive 30 periodicals ! life crypto ipsec security association seconds 28800 ! interface GigabitEthernet0/0.4002 card crypto CMAP_1 ! I tried ISA550 a config with the same constelations, but without suggesting. Anyone has the same problem? And had anyone has a tip for me, or has someone expirense with a site-by-site with ISA550 and Cisco 2821 ipsec tunnel? I can successfully establish a tunnel between openswan linux server and the isa550. Patrick, as you can see on newspapers, the software behind ISA is also OpenSWAN I have a facility with a 892 SRI running which should be the same as your 29erxx. Use your IOS Config dynmap, penny, you are on the average nomad. If you don't have any RW customer you shoul go on IOS "No.-xauth" after the isakmp encryption key. Here is my setup, with roardwarrior AND 2, site 2 site. session of crypto consignment logging crypto ezvpn ! crypto ISAKMP policy 1 BA 3des preshared authentication Group 2 lifetime 28800 ! crypto ISAKMP policy 2 BA 3des md5 hash preshared authentication Group 2 lifetime 28800 ! crypto ISAKMP policy 3 BA 3des preshared authentication Group 2 ! crypto ISAKMP policy 4 BA 3des md5 hash preshared authentication Group 2 ! crypto ISAKMP policy 5 BA 3des preshared authentication Group 2 life 7200 ISAKMP crypto address XXXX XXXXX No.-xauth key XXXX XXXX No.-xauth address isakmp encryption key ! ISAKMP crypto client configuration group by default key XXXX DNS XXXX default pool ACL easyvpn_client_routes PFS ! ! Crypto ipsec transform-set esp-3des esp-sha-hmac FEAT ! dynamic-map crypto VPN 20 game of transformation-FEAT market arriere-route ! ! card crypto client VPN authentication list by default card crypto VPN isakmp authorization list by default crypto map VPN client configuration address respond 10 VPN ipsec-isakmp crypto map Description of VPN - 1 defined peer XXX game of transformation-FEAT match the address internal_networks_ipsec 11 VPN ipsec-isakmp crypto map VPN-2 description defined peer XXX game of transformation-FEAT PFS group2 Set match the address internal_networks_ipsec2 card crypto 20-isakmp dynamic VPN ipsec VPN ! ! Michael Please note all useful posts Cisco VPN and Cisco 2651 customer support I 2651 and remote VPN client Client can successfully establish VPN to 2651 but nothing through this tunnel. In the stats customers there are no decrypted packets. In 2651 I saw the incoming packets but no response. What evil? (This cisco also make VPN tunnel with each other) 2651 config: version 12.3 customer password username AAA new-model AAA authentication login userauthen local AAA - the id of the joint session crypto ISAKMP policy 3 BA 3des preshared authentication Group 2 ! crypto ISAKMP policy 10 md5 hash preshared authentication ISAKMP crypto key xxxx address xx.xx.xx.xx ISAKMP crypto nat keepalive 20 ! ISAKMP crypto client configuration group 3000client xxxxxxxxxxxx key DNS 192.168.77.1 win 192.168.77.1 area xxx.xx pool ippool ACL 111 ! ! Crypto ipsec transform-set esp - esp-md5-hmac M-Chel ! Crypto-map dynamic dynmap 10 game of transformation-M-Chel ! ! card crypto client TunnelMap of authentication list userauthen card crypto isakmp authorization list groupauthor TunnelMap client configuration address card crypto TunnelMap answer map TunnelMap 1 ipsec-isakmp crypto defined peer xx.xx.xx.xx game of transformation-M-Chel match address 110 map TunnelMap 10-isakmp ipsec crypto dynamic dynmap ! ! ! interface FastEthernet0/0 Description link to DMZ IP address xxx.xxx.xxx.252 255.255.255.224 no ip route cache no ip mroute-cache automatic duplex automatic speed No cdp enable no cache route NCLC NAT outside IP card crypto TunnelMap ! interface FastEthernet0/1 Description network internal IP 192.168.77.17 255.255.255.0 no ip route cache no ip mroute-cache automatic duplex automatic speed No cdp enable NAT outside IP no cache route NCLC ! local pool IP 192.168.10.1 ippool 192.168.10.50 IP nat inside source list 1 interface FastEthernet0/0 overload IP route 0.0.0.0 0.0.0.0 xxx.xxx.xxx.xxx permanent ! access-list 110 permit ip 192.168.77.0 0.0.0.255 host xx.xx.xx.xx access-list 111 allow ip 192.168.77.0 0.0.0.255 192.168.10.0 0.0.0.255 Two things: You have not defined a group of authorization specifying that authorization for VPN clients will be done locally. Add the following: AAA authorization groupauthor LAN And your NAT statement is probably wrong, even if you have not shown that the ACL 1 is equal to. follow these steps: IP nat inside source list 100 int fa0/0 overload access-list 100 deny ip 192.168.77.0 0.0.0.255 host xx.xx.xx.xx access-list 100 deny ip 192.168.77.0 0.0.0.255 192.168.10.0 0.0.0.255 access-list 100 permit ip 192.168.77.0 0.0.0.255 any no nat ip within the source list 1 int Fa0/0 overload Note that if you get an error after this last order saying NAT entries are in use, leave the config mode, do: clear the ip nat trans *. return to mode config, and then retype the command. You must make sure that when you do a 'wr t', there is only a single command 'ip nat inside source... ". "in the config and it is the one that refers to ACL 100. VPN between Cisco and Check Point problem Guys, I have problems to establish a vpn site-to-site between a Cisco 3660 e router tunnel a firewall checkpoint NG AI R55. In the SiteA is an environment with a Cisco 3660 router using the following configurations: crypto ISAKMP policy 1 md5 hash preshared authentication Group 2 life 86400 ! ISAKMP crypto key [removed] address 172.17.10.111 ! Crypto ipsec transform-set esp - esp-md5-hmac serasa ! Serasa 1 ipsec-isakmp crypto map defined by peer 172.17.10.111 Set transform-set serasa match address 101 ! interface Serial5/4 bandwidth 64 IP 192.168.163.6 255.255.255.252 no ip unreachable No cdp enable card crypto serasa ! IP route 10.12.0.155 255.255.255.255 192.168.163.5 IP route 172.17.10.111 255.255.255.255 192.168.163.5 IP route 172.17.10.155 255.255.255.255 192.168.163.5 ! access-list 101 permit tcp 172.248.7.200 host 10.12.0.0 0.0.255.255 eq 3315 In the SiteB, we have an environment highly available Nokia using VRRP. The IP address configured as a cluster in the Control Point is 172.17.10.111. We have already confirmed all the configurations of the phase 1 and 2 and is OK, but the VPN is not established. The following messages appear in the router and the firewall: ROUTER June 15 at 10:39:24 orbital: ISAKMP (0:252): check IPSec 1 proposal June 15 at 10:39:24 orbital: ISAKMP: turn 1 ESP_DES June 15 at 10:39:24 orbital: ISAKMP: attributes of transformation: June 15 at 10:39:24 orbital: ISAKMP: program is 1 June 15 at 10:39:24 orbital: ISAKMP: type of life in seconds June 15 at 10:39:24 orbital: ISAKMP: life of HIS (basic) 3600 June 15 at 10:39:24 orbital: ISAKMP: type of life in kilobytes June 15 at 10:39:24 orbital: ISAKMP: service life of SA (IPV) 0x0 0 x 46 0 50 x 0 x 0 June 15 at 10:39:24 orbital: ISAKMP: authenticator is HMAC-MD5 June 15 at 10:39:24 orbital: ISAKMP (0:252): atts are acceptable. June 15 at 10:39:24 orbital: IPSEC (validate_proposal_request): part #1 of the proposal (Eng. msg key.) Local INCOMING = 192.168.163.6, distance = 172.17.10.111,. local_proxy = 172.248.7.200/255.255.255.255/0/0 (type = 1), remote_proxy = 10.12.0.0/255.255.0.0/0/0 (type = 4), Protocol = ESP, transform = esp - esp-md5-hmac. lifedur = 0 and 0kb in SPI = 0 x 0 (0), id_conn = 0, keysize = 0, flags = 0 x 2 June 15 at 10:39:24 orbital: IPSEC (kei_proxy): head = serasa, card-> ivrf =, kei-> ivrf = June 15 at 10:39:24 orbital: IPSEC (validate_transform_proposal): proxy unsupported identities June 15 at 10:39:24 orbital: ISAKMP (0:252): IPSec policy invalidated proposal June 15 at 10:39:24 orbital: ISAKMP (0:252): politics of ITS phase 2 is not acceptable! (local 192.168.163.6 remote 172.17.10.111) June 15 at 10:39:24 orbital: ISAKMP: node set 2114856837 to QM_IDLE June 15 at 10:39:24 orbital: ISAKMP (0:252): lot of 200.245.207.111 sending my_port 500 peer_port 500 (I) QM_IDLE June 15 at 10:39:24 orbital: ISAKMP (0:252): purge the node 2114856837 June 15 at 10:39:24 orbital: ISAKMP (0:252): unknown entry for node-528822595: State = IKE_QM_I_QM1, large = 0x00000001, minor = 0x0000000C June 15 at 10:39:24 orbital: % CRYPTO-6-IKMP_MODE_FAILURE: fast processing mode failed with the peer to 172.17.10.111 FIREWALL IKE: Main Mode has received Notification of peers: first Contact IKE: Completion of Main Mode. IKE: Quick Mode has received Notification of the counterpart: no proposal chosen IKE: Quick Mode has received Notification of the counterpart: no proposal chosen IKE: Exchanging information received remove peer IKE - SA: Anyone have idea who might be the problem? Thank you very much for the help. Fabiano Mendonca. Cool. pls mark as resolved if that might help others... the rate of responses if deemed useful... REDA IPsec VPN with Cisco AnyConnect and 1921 ISR G2 router Hello Is it possible to establish a remote access VPN IPSec using Cisco Anyconnect client with router Cisco ISR G2 1921. If someone does share it please the sample configuration. as I've been on this topic since last week a. My Cisco rep recommended I have not try AnyConnect a router ISR or ASR. So I used an Open Source client. Don't say that AnyConnect won't work, just the route I took on my project. I work good known configuration for a 1921 with strongSwan as a Client. It is with IPSEC and IKEV2 using certificates for authentication. Authentication failed-2008 NPS of VPN from Cisco IOS I'm trying to authenticate VPN connections to a Windows 2008 Server NPS Radius server. Local authentication works very well. This is the cisco configs: AAA new-model radius of the IP source-interface Loopback0 list of authentication of card crypto VPNMAP customer VPNauth ... other cryptographic controls This is the section of the NPS logs: Information about authentication: I have PAP enabled on network connection request policies /... I'm stuck Help, please You can run a "nipple aaa"command to see if the user can be authenticated successfully?" I think this might be a configuration problem on the NPS server. You can google it. Here is one that I have found, refer to the position of "irishHam". Can't free up space for Sierra install After downloading mac os Sierra, I started to install it. I forgot to check my disk space. now I'm stuck in this message: Mac OS could not be installed on your computer - there is not enough free space on - to install. I tried to go into safe mode. n I have a MBP Late 2013 will pair does not with 6s on Blutooth Read all comments (lots of old stuff on these communities) and tried all the suggestions of trashing the plist etc etc. Still unable to get my iPhone 6s to pair with my MBP end 2013. For a fleeting moment after that match it says connected not connec Cannot add Pitchfork-organized playlists to my music (music from Apple) In iTunes/Apple music, I am unable to add Pitchfork-organized playlists to my music. Any other reading list, I can click on the plus sign or "Add to my music", and they appear instantly on my playlists on my Mac and on my other devices synced. When I I can't run a sweep of security on the computer. Original title: Security Scan does not work I tried to run a Security Scan. I get the download bar that shows 100% download so he said start scanning PC, a few seconds later, which disappears and nothing is scanned or loaded. How do the scan to com Parental controls on Windows 7 For more than two years, I have install parental controls with the family of security filters on the computer used by my children. I have NOT connected to the computer or seen the reports. When I try to access the reports today, it took me to a Web sSimilar Questions
VPN id 100
neighbor 1.1.1.1 mpls encapsulation
no ip address
Shutdown
PFD xconnect tests
!
interface Vlan121
no ip address
Check the interface MTU, VLAN ID size
Or try to configure BPDU PW on routed SVI, which is not allowed
AAA authentication login default local
AAA authentication login VPNauth local radius group
local AAA VPNgroup authorization network
AAA - the id of the joint session
RADIUS-server host x.x.x.x auth-port 1645 acct-port 1646 button 7 xxxx
card crypto VPNMAP VPNgroup isakmp authorization list
crypto card for the VPNMAP client configuration address respond
map VPNMAP 10-isakmp ipsec crypto dynamic dynmap
...
Connection request policy name: VPN
The network policy name: -.
Authentication provider: Windows
Authentication server: x.x.x.x
Authentication type: PAP
EAP type: -.
Identifier for account: -.
Results of logging: Accounting Information was written in the local log file.
Reason code: 16
Reason: Authentication failed due to incompatibility of user credentials. The provided username is not mapped to an existing user account or the password is incorrect.Maybe you are looking for