Questions of hub L2L with Checkpoint NGR55 3K 5
I am trying to create a connection L2L from a 3 K 5 hub to a seller with a NGR55 of control point. Setting up this morning, we have been able to access all applications using a NAT on their side, they were not able to access our own. The message that we've seen on both sides was:
No routine received Notify message: info ID not valid (18)
Which indicates the incompatible attributes between the peers. These have been verified on both sides. We have our list of local network specified as all the individual hosts that are translated into static NAT rules. For them, we have static translations and two global PATs... the network list for them specifies all their/24 network, which has been used in the comprehensive PAT. My understanding is that the most specific network will be applied and if not found, the PAT will be used, and I can see what is happening in the case where newspaper.
Question 1.) This could be a possible problem with why they are unable to connect to what anyone on our side?
Question 2.) The hub is driven by, even from the menu CLI and I can't find a way to clean up the SA when troubleshooting other than the deactivation and reactivation of the tunnel. I know about the ASA and PIX and I can do for phases 1 and 2 of the CLI. Deactivation of the tunnel on the 3 K 5 has the same result?
Any other ideas on why this would be appreciated.
It is very likely that the checkpoint is
do suppernetting, causing Phase 2
Quick mode error. I could do this on the
side of control point:
1 - Open a session in the check point gateway,
2. "you vpn" and remove the tunnel between
point of control and VPNc,
2 - cd $FWDIR/log,.
3 - vpn debugging trunc,
4 - vpn debugging ikeoff,
5 - vpn debugging ikeon,
6. now initialize the connection of control point
side. It will fail,
7 - get the ike.elg file and export it
on your desktop via scp or whatever.
8 - use a tool called IKEView.exe control point
utility and open the ike.elg file.
This will tell you EXACTLY why the tunnel failed and why. It is very likely that
control point is suppernetting its network and
Send it to VPNc, causing phase II for
in case of failure.
To resolve this problem, you will have
to modify the parameter "IKE_largest_possible_subnet" to "true" to "false" and also change the file user.def as
Well.
The other solution is to switch to the NGx so
you have an option to negotiate 'by '.
host' and have communication on both sides.
Sounds easy?
Now,.
Tags: Cisco Security
Similar Questions
-
Hi, my, library, has been damaged, so I have, open, a, FCP BU library and this worked well, so my, question, is, what, do, with, the, old, library,?, is, always, workin g throughout, with, a, I have used?, or, well, I have, open, BU, one, i, used, each, times, I, open, my, project?
Rename your backup library in order to take account of the original, and then delete the original.
FYI: Identification will facilitate a slightly different name.
Al
-
I'm looking to move from Windows/Apple/Logic Pro X and Cubase Cubase.
My questions have to do with the current (2014) Mac mini, specifically the i5 $999 2.8 GHz with 8 GB of RAM.
This computer will be powerful enough to run Logic Pro X DAW and Cubase 8 courses without any problem?
I would say yes, but I post here too:
-
On my Mac Book Pro to always stop get question "continue application"? with the boxes option to cancel or continue the request.
Selection of abandonment does not prevent the following message appears when closing next down.
Activity monitor shows all the applications that you have
installed, running in the background? Something can be...
If you open the force quit, are there topics other than the Finder
and maybe a browser?
You repaired the disk from disk utility permissions lately?
We could also see other boot options on the use in
Recovery of OS X to use the "OS X Utilities" in there. Be careful.
Is there more than one user account on your computer? If you
Start in another user account and have auto login for
the fact that it is one that rises at the start, a piece
similar issues or is it just works fine on shut down?
The question may take some trial and error troubleshooting. This
may include some basic startup keyboard shortcuts for
the computer to start in Safe Mode, to do more test, etc.
If you have access to an official Apple store, you can be
able to set up an engineering appointment & have someone closer.
Good luck anyway...
-
I read this topic (I have a lot of questions about Xperia Z2 with lollipop)
Hello world. I read this topic (I have a lot of questions about Xperia Z2 with lollipop) and I have posted a question, but it seems that no one saw him. That means the following: (how can I install the source application unknown to other users in my phone because it is to the unknown source menu is disabled in the settings-> Security)? This means that I can not install all the apps if I switch to the lollipop? Can someone tell me please the exact meaning of this?
Thank you.
It's true, but game store will not need this option checked - loading of a file manager will - but which is not say that the application will work once installed
-
IOS mixed Crypto Maps with Checkpoint Firewall
I have a config encryption that works very well with a remote CheckPoint Firewall:
-------------- \/ CONFIG 1 \/--------------------
crypto ISAKMP policy 5
BA 3des
md5 hash
preshared authentication
!
ISAKMP crypto key address 1.2.3.4 cryptokey1
!
Crypto ipsec transform-set esp-3des esp-md5-hmac txfrmset1
!
crypto dynamic-map vpn Dynamics 10
Set transform-set txfrmset1
!
secure1_in card crypto ipsec isakmp 1
defined by peer 205.245.184.2
Set transform-set txfrmset1
match address 105
!
IP nat inside source overload map route sheep interface Ethernet0
!
sheep allowed 10 route map
corresponds to the IP 110
!
access-list 105 permit ip 192.168.10.0 0.0.0.255 192.168.20.0 0.0.0.255
------------/\ CONFIG 1 /\ --------------------
I need to add a card for remote clients using the Cisco VPN 3.6 client.
I have a card encryption that has worked great for me in the past. The combination
Both looks like this:
---------------\/ CONFIG 2 \/ --------------------------
Nine AAA
AAA authentication login userauthen local
AAA authorization groupauthor LAN
crypto ISAKMP policy 5
BA 3des
md5 hash
preshared authentication
!
crypto ISAKMP policy 10
BA 3des
md5 hash
preshared authentication
Group 2
!
cryptokey1 key crypto isakmp address 1.2.3.4 No.-xauth
!
Crypto ipsec transform-set esp-3des esp-md5-hmac txfrmset1
!
crypto dynamic-map vpn Dynamics 10
Set transform-set txfrmset1
ISAKMP crypto client configuration group remote1
cryptokey2 key
DNS 10.0.0.4
WINS 10.0.0.5
VPN-pool
!
card crypto client secure1_in of authentication list userathen
card crypto isakmp authorization list groupauthor secure1_in
client configuration address card crypto secure1_in answer
secure1_in map ipsec-isakmp crypto 5
defined peer 1.2.3.4
Set transform-set txfrmset1
match address 105
vpnclient 10-isakmp ipsec vpn dynamic-dynamic crypto map
!
IP VPN-pool pool 172.16.30.1 room 172.16.30.254
IP nat inside source overload map route sheep interface Ethernet0
access-list 105 permit ip 192.168.10.0 0.0.0.255 192.168.20.0 0.0.0.255
!
access-list 110 deny ip 192.168.10.0 0.0.0.255 192.168.20.0 0.0.0.255
access-list 110 permit ip 192.168.0.0 0.0.0.255 any
!
sheep allowed 10 route map
corresponds to the IP 110
---------------/\ CONFIG 2 /\---------------------------
It's classic crypto right out of the playbook of Cisco. This card works
very well with the Cisco VPN client, but produced the following errors after a
successful with Checkpoint Firewall P1 installation:
--------------\/ ERROR OUTPUT \/ -----------------------
05:13:02: ISAKMP (0:2): send package to 1.2.3.4 (R) MM_KEY_EXCH
05:13:02: ISAKMP (0:2): entry = IKE_MESG_INTERNAL, IKE_PROCESS_COMPLETE
Former State = new State IKE_R_MM5 = IKE_P1_COMPLETE
05:13:02: ISAKMP (0:2): need to config/address
05:13:02: ISAKMP (0:2): need to config/address
05:13:02: ISAKMP: node set 1502565681 to CONF_ADDR
05:13:02: ISAKMP (0:2): pool of IP addresses not defined for ISAKMP.
05:13:02: ISAKMP (0:2): node 1502565681 error suppression FALSE reason «»
05:13:02: ISAKMP (0:2): entry = IKE_MESG_INTERNAL, IKE_PHASE1_COMPLETE
Former State = new State IKE_P1_COMPLETE = IKE_CONFIG_MODE_SET_SENT
05:13:02: ISAKMP (0:2): 1.2.3.4 received packet (R) CONF_ADDR
05:13:02: ISAKMP: node set-1848822857 to CONF_ADDR
05:13:02: ISAKMP (0:2): entry unknown: status = IKE_CONFIG_MODE_SET_SENT, major, minor = IKE_MESG_INTERNAL, IKE_PHASE1_COMPLETE
05:13:04: ISAKMP (0:2): 1.2.3.4 received packet (R) CONF_ADDR
--------------/\ ERROR OUTPUT /\--------------------------
This does not happen to config 1. If it's a PIX, I would use the
No.-config-mode keyword after the No.-xauth on isakmp crypto "key."
command line. It is not available on IOS IPSEC and I have never
needed to do before. I am running Cisco IOS 12.2 (5.4) T on a VPN of 1721
router. The static map seems to work by itself. What I am doing wrong?
I saw her a couple of times and to be honest have never taken down to an exact cause, although in this case it looks like almost to the point of control request an IP address which is weird. Try the following:
1. Add "card crypto secure1_in client configuration address to initiate" and see what it does.
2. try 12.2 (8) code T5 with it, I had a previous user running 12.2 (11) T and we got the same error messages, returning to this level of code it is resolved.
In addition, you wouldn't need:
> access-list 110 deny ip 192.168.10.0 0.0.0.255 172.16.30.0 0.0.0.255
for example, so that you do not NAT client VPN traffic?
-
Question Z10 Z10 blackBerry with management hub
Good, everyone
Tried to disable notifications in management hub for some applications like facebook and foursquare. I didn't have a chance. Notifications appear in the left panel black while in another application yet and I have to mark opened each time.
A way to fix it?
Best regards
Problem solved: download 4square, it is necessary to choose only one type of connection or 3G, wi - fi.
Calls in the hub got their name after you remove all the BB and download back again.
-
Traffic from internal hosts will NAT address works ok, but what speaks tests it traffic never connects.
get the 10.1.12.232 NAT host would be 172.27.63.133 and past through the VPN tunnel to 10.24.4.65 without problem. However when 10.24.4.65 tries to ping or connect to 172.27.63.133 traffic does not make inside host 10.1.12.232
ASA-1 #.
!
network object obj - 172.27.73.0
172.27.73.0 subnet 255.255.255.0
network object obj - 172.27.63.0
172.27.63.0 subnet 255.255.255.0
network object obj - 10.1.0.0
10.1.0.0 subnet 255.255.0.0
network object obj - 10.24.4.64
subnet 10.24.4.64 255.255.255.224
network object obj - 172.27.73.0 - 172.27.73.255
range 172.27.73.0 172.27.73.255
the object of the 10.0.0.0 network
subnet 10.0.0.0 255.0.0.0
network object obj - 24.173.237.212
Home 24.173.237.212
network object obj - 10.1.12.232
Home 10.1.12.232
network object obj - 172.27.63.133
Home 172.27.63.133
the DM_INLINE_NETWORK_9 object-group network
object-network 10.0.0.0 255.255.255.0
object-network 10.0.11.0 255.255.255.0
object-network 10.0.100.0 255.255.255.0
object-network 10.0.101.0 255.255.255.0
object-network 10.0.102.0 255.255.255.0
object-network 10.0.103.0 255.255.255.0
the DM_INLINE_NETWORK_16 object-group network
object-network 10.1.11.0 255.255.255.0
object-network 10.1.12.0 255.255.255.0
object-network 10.1.13.0 255.255.255.0
object-network 10.1.3.0 255.255.255.0
!
outside_1_cryptomap list extended access permitted ip object-group DM_INLINE_NETWORK_16-group of objects DM_INLINE_NETWORK_9
access extensive list ip 172.27.73.0 outside_8_cryptomap allow 255.255.255.0 10.24.4.64 255.255.255.224
access extensive list ip 172.27.63.0 outside_8_cryptomap allow 255.255.255.0 10.24.4.64 255.255.255.224
!
list of allowed outside access extended ip 10.24.4.64 255.255.255.224 172.27.63.0 255.255.255.0
list of allowed outside access extended ip 10.24.4.64 255.255.255.224 10.1.0.0 255.255.0.0
list of allowed outside access extended ip 172.27.63.0 255.255.255.0 10.1.0.0 255.255.0.0
!
NAT (inside, all) source static obj - 172.27.73.0 obj - 172.27.73.0 destination static obj - 10.24.4.64 obj - 10.24.4.64 no-proxy-arp-search to itinerary
NAT (inside, all) source static obj - 172.27.63.0 obj - 172.27.63.0 destination static obj - 10.24.4.64 obj - 10.24.4.64 no-proxy-arp-search to itinerary
NAT (inside, outside) source dynamic obj - 10.66.0.0 obj - 172.27.73.0 - 172.27.73.255 destination static obj - 10.24.4.64 obj - 10.24.4.64
NAT (inside, outside) source dynamic obj - 10.70.0.0 obj - 172.27.73.0 - 172.27.73.255 destination static obj - 10.24.4.64 obj - 10.24.4.64
NAT (inside, outside) source dynamic obj - 10.96.228.0 obj - 172.27.73.0 - 172.27.73.255 destination static obj - 10.24.4.64 obj - 10.24.4.64
NAT (inside, outside) source dynamic obj - 10.96.229.0 obj - 172.27.73.0 - 172.27.73.255 destination static obj - 10.24.4.64 obj - 10.24.4.64
NAT (inside, outside) source dynamic obj - 192.168.5.0 obj - 172.27.73.0 - 172.27.73.255 destination static obj - 10.24.4.64 obj - 10.24.4.64
NAT (inside, outside) source dynamic obj - 10.75.0.0 obj - 172.27.73.0 - 172.27.73.255 destination static obj - 10.24.4.64 obj - 10.24.4.64
NAT (inside, outside) source dynamic obj - 10.11.0.0 obj - 172.27.73.0 - 172.27.73.255 destination static obj - 10.24.4.64 obj - 10.24.4.64
NAT (inside, outside) source static obj - 10.1.3.37 obj - 10.71.0.37 destination static obj - 50.84.209.140 obj - 50.84.209.140
NAT (inside, outside) source static obj - 10.1.3.38 obj - 10.71.0.38 destination static obj - 50.84.209.140 obj - 50.84.209.140
NAT (inside, outside) source static obj - 10.1.12.232 obj - 172.27.63.133 destination static obj - 10.24.4.64 obj - 10.24.4.64
NAT (inside, outside) source dynamic obj - 10.1.0.0 obj - 172.27.73.0 - 172.27.73.255 destination static obj - 10.24.4.64 obj - 10.24.4.64
!
NAT (exterior, Interior) source static obj - 10.24.4.64 obj - 10.24.4.64 destination static obj - 172.27.63.133 obj - 10.1.12.232
NAT (outside, outside) source static obj - 10.24.4.64 obj - 10.24.4.64 destination static obj - 172.27.63.133 obj - 10.1.12.232the object of the 10.0.0.0 network
NAT (inside, outside) dynamic obj - 24.173.237.212
!
NAT (VendorDMZ, outside) the after-service automatic source dynamic obj - 192.168.13.0 obj - 24.173.237.212
outside access-group in external interface
Route outside 0.0.0.0 0.0.0.0 24.173.237.209 1
Route inside 10.1.0.0 255.255.0.0 10.1.10.1 1
Route inside 10.2.1.0 255.255.255.248 10.1.10.1 1
!
Crypto ipsec transform-set ikev1 SHA-ESP-3DES esp-3des esp-sha-hmac
Crypto ipsec transform-set ikev1 ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
Crypto ipsec transform-set ikev1 ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-3DES-SHA-DH2-esp-3des esp-sha-hmac
Crypto ipsec pmtu aging infinite - the security association
!
card crypto GEMed 8 corresponds to the address outside_8_cryptomap
card crypto GEMed 8 set peer 64.245.57.4
card crypto GEMed 8 set ikev1 transform-set ESP-AES-256-SHA ESP-AES-256-MD5
GEMed outside crypto map interface
!
: end
ASA-1 #.Hello
First of all, I would like to remove these two lines because they do nothing productive
nat (outside,inside) source static obj-10.24.4.64 obj-10.24.4.64 destination static obj-172.27.63.133 obj-10.1.12.232nat (outside,outside) source static obj-10.24.4.64 obj-10.24.4.64 destination static obj-172.27.63.133 obj-10.1.12.232
Then, I was running packet - trace to see what NAT rule actually hit you.packet-tracer input inside 10.1.12.232 12345 10.24.4.65 12345
-
I am confuse
I have a regular e-mail account with "Free Webmail"
Later, I add 2 more on «Webmail Free» e-mail accounts
I've used them for a while now and I remember even the connection of these last two account.
Now when I want to save my e-mail account in the HUB, he always says, my connection is bad...:!
Why?
It is perhaps one of the other 2.
Can someone help me?
Maybe I don't understand your question, but without the connection information, you cannot add accounts. Add in your accounts go to settings > accounts and enter the credentials it. If you do not know your passwords, you need to reset with these suppliers.
-
L2l with certificates between 2 ASAs
Hi all
I want to set up a VPN L2L/Site-to-site tunnel, which authenticates by using certificates.
In fact I am following this guide-> http://www.cisco.com/en/US/products/ps6120/products_configuration_example09186a0080aa5be1.shtml
I configured the tunnel group on both ends, with the trustpoint configured, authenticated and accepted specified.
I correspondent isakmp policies at both ends, and of course my cryptographic cards contains 3 identical lines - set peer match access-list and transformation-a set cryptomap. Next to those, there are 2 identical lines for life. I haven't specified the trustpoint in encryption card while it is not indicated in the top link (guide) to do, even if I tried, without different result. Debugs him happens exactly the same each time:
Debug the cry isa 10: (on the remote end)
TEST-ASA-RA # debug cry isa 10
TEST-ASA-RA # Jul 07 11:36:18 [IKEv1]: IP = 80.62.240.136, IKE_DECODE RECEIPT Message (msgid = 0) with payloads: HDR + SA (1) the SELLER (13) + the SELLER (13) + the SELLER (13), SELLER (13) + (0) NONE total length: 208
Jul 07 11:36:18 [IKEv1 DEBUG]: IP = 80.62.240.136, SA payload processing
Jul 07 11:36:18 [IKEv1 DEBUG]: IP = 80.62.240.136, Oakley proposal is acceptable
Jul 07 11:36:18 [IKEv1 DEBUG]: IP = 80.62.240.136, payload processing VID
Jul 07 11:36:18 [IKEv1 DEBUG]: IP = 80.62.240.136, received NAT-Traversal worm 02 VID
Jul 07 11:36:18 [IKEv1 DEBUG]: IP = 80.62.240.136, payload processing VID
Jul 07 11:36:18 [IKEv1 DEBUG]: IP = 80.62.240.136, worm received 03 NAT-Traversal, VID
Jul 07 11:36:18 [IKEv1 DEBUG]: IP = 80.62.240.136, payload processing VID
Jul 07 11:36:18 [IKEv1 DEBUG]: IP = 80.62.240.136, received NAT - Traversal RFC VID
Jul 07 11:36:18 [IKEv1 DEBUG]: IP = 80.62.240.136, payload processing VID
Jul 07 11:36:18 [IKEv1 DEBUG]: IP = 80.62.240.136, received Fragmentation VID
Jul 07 11:36:18 [IKEv1 DEBUG]: IP = 80.62.240.136, IKE Peer included IKE fragmentation capability flags: Main Mode: real aggressive Mode: true
Jul 07 11:36:18 [IKEv1 DEBUG]: IP = 80.62.240.136, IKE SA payload processing
Jul 07 11:36:18 [IKEv1 DEBUG]: IP = 80.62.240.136, IKE SA proposal # 1, turn # 1 entry IKE acceptable Matches # 3 overall
Jul 07 11:36:18 [IKEv1 DEBUG]: IP = 80.62.240.136, build the payloads of ISAKMP security
Jul 07 11:36:18 [IKEv1 DEBUG]: IP = 80.62.240.136, construction of Fragmentation VID + load useful functionality
Jul 07 11:36:18 [IKEv1]: IP = 80.62.240.136, IKE_DECODE SEND Message (msgid = 0) with payloads: HDR + HER (1), SELLER (13) + (0) NONE total length: 108
Jul 07 11:36:18 [IKEv1]: IP = 80.62.240.136, IKE_DECODE RECEIPT Message (msgid = 0) with payloads: HDR + KE (4) NUNCIO (10) + CERT_REQ (7) + CERT_REQ (7) seller (13) + the seller (13) + the seller (13) + the seller (13) + (0) NONE total length: 374
Jul 07 11:36:18 [IKEv1 DEBUG]: IP = 80.62.240.136, processing ke payload
Jul 07 11:36:18 [IKEv1 DEBUG]: IP = 80.62.240.136, payload processing ISA_KE
Jul 07 11:36:18 [IKEv1 DEBUG]: IP = 80.62.240.136, nonce payload processing
Jul 07 11:36:18 [IKEv1 DEBUG]: IP = 80.62.240.136, treatment certificate request payload
Jul 07 11:36:18 [IKEv1 DEBUG]: IP = 80.62.240.136, treatment certificate request payload
Jul 07 11:36:18 [IKEv1 DEBUG]: IP = 80.62.240.136, payload processing VID
Jul 07 11:36:18 [IKEv1 DEBUG]: IP = 80.62.240.136, the customer has received Cisco Unity VID
Jul 07 11:36:18 [IKEv1 DEBUG]: IP = 80.62.240.136, payload processing VID
Jul 07 11:36:18 [IKEv1 DEBUG]: IP = 80.62.240.136, received xauth V6 VID
Jul 07 11:36:18 [IKEv1 DEBUG]: IP = 80.62.240.136, payload processing VID
Jul 07 11:36:18 [IKEv1 DEBUG]: IP = 80.62.240.136, treatment VPN3000 / ASA payload IOS Vendor ID theft (version: 1.0.0 capabilities: 20000001)
Jul 07 11:36:18 [IKEv1 DEBUG]: IP = 80.62.240.136, payload processing VID
Jul 07 11:36:18 [IKEv1 DEBUG]: IP = 80.62.240.136, received Altiga/Cisco VPN3000/Cisco ASA GW VID
Jul 07 11:36:18 [IKEv1 DEBUG]: IP = 80.62.240.136, building ke payload
Jul 07 11:36:18 [IKEv1 DEBUG]: IP = 80.62.240.136, building nonce payload
Jul 07 11:36:18 [IKEv1 DEBUG]: IP = 80.62.240.136, building certreq payload
Jul 07 11:36:18 [IKEv1 DEBUG]: IP = 80.62.240.136, build payloads of Cisco Unity VID
Jul 07 11:36:18 [IKEv1 DEBUG]: IP = 80.62.240.136, constructing payload V6 VID xauth
Jul 07 11:36:18 [IKEv1 DEBUG]: IP = 80.62.240.136, Send IOS VID
Jul 07 11:36:18 [IKEv1 DEBUG]: IP = 80.62.240.136, ASA usurpation IOS Vendor ID payload construction (version: 1.0.0 capabilities: 20000001)
Jul 07 11:36:18 [IKEv1 DEBUG]: IP = 80.62.240.136, build payloads VID
Jul 07 11:36:18 [IKEv1 DEBUG]: IP = 80.62.240.136, Send Altiga/Cisco VPN3000/Cisco ASA GW VID
Jul 07 11:36:18 [IKEv1 DEBUG]: IP = 80.62.240.136, Generating keys for answering machine...
Jul 07 11:36:18 [IKEv1]: IP = 80.62.240.136, IKE_DECODE SEND Message (msgid = 0) with payloads: HDR + KE (4) NUNCIO (10) + CERT_REQ (7) seller (13) + the seller (13) + the seller (13) + the seller (13) + (0) NONE total length: 298
Jul 07 11:36:18 [IKEv1 DEBUG]: IP = 80.62.240.136, RRs would fragment a new set of fragmentation. Removal of fragments of old.
Jul 07 11:36:18 [IKEv1 DEBUG]: IP = 80.62.240.136, assembled with success an encrypted pkt of RRs would be fragments!
Jul 07 11:36:18 [IKEv1]: IP = 80.62.240.136, IKE_DECODE RECEIPT Message (msgid = 0) with payloads: HDR + ID (5) + GIS (9) + IOS KEEPALIVE (128) + CERT (6), SELLER (13) + (0) NONE total length: 1987
Jul 07 11:36:18 [IKEv1 DEBUG]: IP = 80.62.240.136, payload processing ID
Jul 07 11:36:18 [IKEv1 DECODER]: IP = 80.62.240.136, ID_IPV4_ADDR received ID
80.62.240.136
Jul 07 11:36:18 [IKEv1 DEBUG]: IP = 80.62.240.136, payload processing cert
Jul 07 11:36:18 [IKEv1 DEBUG]: IP = 80.62.240.136, treatment of RSA signature
Jul 07 11:36:18 [IKEv1 DEBUG]: IP = 80.62.240.136, calculation of hash for ISAKMP
Jul 07 11:36:18 [IKEv1 DECODER]: Dump of Signature received, len 256:
0000: 8D97FE83 CDA9CEB2 A5D7F63F 0FAA76A4...? ... c.
0010: 21F229A8 2A714C2D 12F16ABF 08E44664!.). *... qL j... FD
0020: 0D95A510 0AFFA63B 815CCBB0 B7C708CF...; \......
0030: 31246316 0E93E084 59395461 118C 9251 $1 c... Y9Ta... Q
0040: 823A36CB 55F2F59C 3342326D 251F8B7A. : 6.U... 3B2m %... z
0050: B9C9F916 C403A4D1 59DA3AA8 932312C 0... Y.:.. #..
0060: 88476460 E9C9A07C 5671C18D A9202382. GD'... | DV... #.
0070: 441F47AF 74E407B1 DB06B929 406E993D D.G.t...) @n. =
0080: A7C149FA 1677D1A2 E3105356 4E205E45... I have... w... SVN ^ E
0090: 06D2CB2A B6BF638E 0910283C 7FF6BAE2... *... c... (<>
00 to 0: 3F97ADF5 19B 78872 69C0346B 7EF89FAE?... ri.4k... ~
00B 0: 456E26CF 52CC296B 11F6AE68 2498024C en &. R) k...h$... L
00C 0: 74658112 you 16121A 68 h
Jul 07 11:36:18 [IKEv1 DEBUG]: IP = 80.62.240.136, IOS treatment keep alive payload: proposal = 32767/32767 sec.
Jul 07 11:36:18 [IKEv1 DEBUG]: IP = 80.62.240.136, payload processing VID
Jul 07 11:36:18 [IKEv1 DEBUG]: IP = 80.62.240.136, DPD received VID
Jul 07 11:36:18 [IKEv1]: IP = 80.62.240.136, trying to find the group via IKE ID...
Jul 07 11:36:18 [IKEv1]: IP = 80.62.240.136, connection landed on tunnel_group 80.62.240.136
Jul 07 11:36:18 [IKEv1 DEBUG]: Group = 80.62.240.136, IP = 80.62.240.136, ID type homologous 1 received (IPV4_ADDR)
Jul 07 11:36:18 [IKEv1]: Group = 80.62.240.136, IP = 80.62.240.136, identity of IKE for peer name incompatibility Cert subject Alt
Jul 07 11:36:18 [IKEv1 DEBUG]: Group = 80.62.240.136, IP = 80.62.240.136, case of mistaken IKE MM Responder WSF (struct & 0xd3dcecf0)
, : MM_DONE, EV_ERROR--> EV_COMPARE_IDS--> MM_BLD_MSG6, MM_BLD_MSG6, NullEvent--> MM_BLD_MSG6, EV_VALIDATE_CERT--> MM_BLD_MSG6, EV_UPDATE_CERT--> MM_BLD_MSG6, EV_TEST_CERT--> MM_BLD_MSG6, EV_CHECK_NAT_T, EV_CERT_OK--> MM_BLD_MSG6 Jul 07 11:36:18 [IKEv1 DEBUG]: Group = 80.62.240.136, IP = 80.62.240.136, IKE SA MM:1e531705 ending: 0x0100c002, refcnt flags 0, tuncnt 0
Jul 07 11:36:18 [IKEv1 DEBUG]: Group = 80.62.240.136, IP = 80.62.240.136, sending clear/delete with the message of reason
Jul 07 11:36:18 [IKEv1 DEBUG]: Group = 80.62.240.136, IP = 80.62.240.136, payload of empty hash construction
Jul 07 11:36:18 [IKEv1 DEBUG]: Group = 80.62.240.136, IP = 80.62.240.136, constructing the payload to delete IKE
Jul 07 11:36:18 [IKEv1 DEBUG]: Group = 80.62.240.136, IP = 80.62.240.136, build payloads of hash qm
Jul 07 11:36:18 [IKEv1]: IP = 80.62.240.136, IKE_DECODE SEND Message (msgid = 5a228b67) with payloads: HDR HASH (8) + DELETE (12) + (0) NONE total length: 80
Jul 07 11:36:18 [IKEv1]: Group = 80.62.240.136, IP = 80.62.240.136, Removing peer to peer table does not, no match!
Jul 07 11:36:18 [IKEv1]: Group = 80.62.240.136, IP = 80.62.240.136, error: cannot delete PeerTblEntry
Jul 07 11:36:26 [IKEv1]: IP = 80.62.240.136, invalid header, lack of payload SA! (next payload = 132)
Jul 07 11:36:26 [IKEv1]: IKE_DECODE SEND Message (msgid = 0) with payloads: HDR + NOTIFY (11) + NONE (0) overall length: 68
Jul 07 11:36:26 [IKEv1]: IP = 80.62.240.136, invalid header, lack of payload SA! (next payload = 132)
Jul 07 11:36:26 [IKEv1]: IKE_DECODE SEND Message (msgid = 0) with payloads: HDR + NOTIFY (11) + NONE (0) overall length: 68
Jul 07 11:36:26 [IKEv1]: IP = 80.62.240.136, invalid header, lack of payload SA! (next payload = 132)
Jul 07 11:36:26 [IKEv1]: IKE_DECODE SEND Message (msgid = 0) with payloads: HDR + NOTIFY (11) + NONE (0) overall length: 68
Then, it waits a bit and start over. No matter if I am trying to establish the tunnel network or remote endpoint - there is no difference in the result.
I made a line of debug output "BOLD" - I don't the have not seen this before, don't think that devices Cisco used this alternative area? Thought it was Microsoft?
1 thing is a reference to the certificates - I use my won Microsoft PKI based on 2003 servers. I have 1 Root CA and 2 subordinates. The root CA is stopped. During the construction of my trustpoints, I start to do my request, give it to one of subordinates, gets my identity certificate and save it on my computer. Then check the chain, which looks always good - RootCA-> SubordinateCA-> ClientCert. Then I extracted the subordinate cert, to authenticate my trustpoint and finally I import the certificate of identity. No complaints, it of all good - and actually working like a charm for my EZVPN configurations.
So I do not think the problem it's with the certificates, although the release said that there is an incompatibility with the other name in question.
The debugging online after this statement, I understand not quite - maybe someone can help me with this? Because right after this line, he begins to destroy the tunnel.
I can provide from configs if necessary, but really, it corresponds to the configuration contained in the guide.
/ Peter
Can you check the "crypto isakmp identity" command on both sides? He looks like a side sends the IP, when it expected the certificate DN is the name so it can match the value in the cert.
Jul 07 11:36:18 [IKEv1 DEBUG]: Group = 80.62.240.136, IP = 80.62.240.136, ID type homologous 1 received (IPV4_ADDR)
Jul 07 11:36:18 [IKEv1]: Group = 80.62.240.136, IP = 80.62.240.136, identity of IKE for peer name incompatibility Cert subject Alt
-Jason
-
Question conectivity Time Capsule with Windows 7
Hello
I am owner of a time Capsule A1309 with 3 TB of memory and it stopped working with my Windows PC for a while. It used to connect normally not long ago, but now the drive doesn't appear and I can't access the time with AirPort Utility Capsule unless I type the IP address. I have a lot of archives stored in the drive and cannot access it from any PC running Windows in my house.
My Control Panel is:
- RAM - 8 GB
- Intel Core i5 - 2430 M 2.40 GHz
- 64 bit
- Windows 7 Professional
I know that the Time Capsule works normally, because I can access it from an old iMac I have here.
Other details: My Time Capsule is on System 7.6.7 version and I also have the last airport utility installed on my PC.
Thanks in advance,
Rodrigo Trindade
For starters, you have access to the Time Capsule (TC) using the AirPort for Windows PC? The question started the TC to 7.6.7 firmware version after update?
-
Hello. When I search on Safari, it freezes in the following situation: I have run a search by typing in the search bar. The search results I get, it's not what I wanted, so I erase the question of search and replace it with another question of research. Instead of a new search result that Safari freezes. What is going on?
IOS 9.2.1 does not run on iMac, as shown in your profile. If you want to help, at the very least, we need to know that the version of Mac OS X installed. If you are not sure, please click on the Apple symbol in the upper left of the screen and select about this Mac.
-
Question about X 220 with 3 x 3 antennae
I ordered a Thinkpad X 220 with the option of 3 x 3 antennae (no cam). The question is, why in the Device Manager, I see 1 x 1 in wireless adapters?
Do I need a better wireless card than the default provided with the X 220?
Thank you
OK, the default map cannot use the 3 antennas. Map of 1 x 1 is invalid, it cannot do the 150mbps Wireless N-Lite, not even 300 and certainly not the 450mbps which can make a 3 x 3 card.
-
Surprisingly, I'm almost finished with a full blown control-simulation application, that I've been working on for more than a year now, thanks in no small part of this community. The final step is to run on the simulations of k ~ 8 and be able to meet a simulation and overall statistics on performance. Each simulation is taking about 6 minutes of real time to run (~ 2 seconds of real time per hour of simulation time, valid for 7 days of simulation), as we seek to about 800 hours of your time to simulate. I have 5 computers available and a raspberry 2 Pi these simulations on, I'm looking to set up a kind of compute cluster at the end in about 2 weeks.
The ability of current logging is sketchy; I got about 40 columns of data, and they are written in a spreadsheet with a .xls format tabs-delimited. This works very well for individual simulations, but it would be quite heavy to deal with if I had more than 20,000 of them. I think this must be done with a relational database sort, but my experience with databases is very limited, especially then, when it comes to LabVIEW. Here are my questions:
-Can I create a kind of master-slave configuration where a computer (and probably the Pi) keeps track of the simulations are complete, which are running, and who have never run? Computers slaves ask for simulation settings, and IP would give them to him.
-How should I take care of the database? Each simulation is about 500 k in .xls format, it's about 5 GB of data in all. Computers slaves synchronization from time to time to take care of the redundancy?
-How can I refine my memory + General fresh disk I/O? How can I know which items from my point of view most of them?
-Do you have suggestions for the implementation of clusters of databases relational/computer with LabVIEW?
I have attached a picture of my configuration of logging + the overall structure of the application. It is a state machine with a structure of the event for the interruptions.
-
Questions of getting started with Service contracts to small businesses
I recently bought small business Service contracts for my Cisco Small Business networking products. I know that I get support 24 x 7, as well as the ability to open cases taken in charge (I recently tried and it works fine).
I also know that I get next day material, as well as firmware upgrade replacement for my networking products.
Here are my some "Getting Started" questions:
1. If I need a replacement of material next day, how can I go to? Open a case of pension? I saw under the requests of support there is an option for the replacement of equipment.
2 will I be automatically informed of updates firmware for my networking products, or I have to look it up on the Support Center? I don't know how to upgrade the firmware of all my networking products. Is it possible to subscribe to a list of email or RSS feeds notifying me of updates firmware for my networking products?
3. I will announce when my service contract is about to expire so I can renew them, or is it my responsibility to do not forget to renew? I have to manually put on my calendar?
Thank you!
(1) to request an RMA number, you must open a case to the HWC. You can call 866-606-1866 24 x 7 to prosecute. If you do not have a support contract, (under warranty) you are only entitled to phone support 09:00-18:00 (local time) m.. You MUST be prepared to troubleshoot the device with the HWC engineer. Do not assume you can open a file and receive an RMA number without looking at the camera. Often, we can save the camera and make you save a lot of time.
(2) you can sign up for automatic alerts on updates of the firmware using this link and by selecting the devices you want updates on. The 2nd link allows you to manually check for updates.
http://www.Cisco.com/Cisco/Web/support/index.html
http://www.Cisco.com/Cisco/support/notifications.html
(3) I checked with HWC contracts administrator. According to her, you should begin to receive alerts from 6 months to 90 days before the expiry of the contract. You may or may not be able to renew the contract, based on the life cycle of the product.
In response to Dirk: you can extend the support of the product by buying a service contract any time during the period of 1 year warranty. A support agreement for your device can be purchased from any local Cisco partner or any Cisco partner online. Here are the main advantages of a contract on the guarantee. They are a great value.
- Extended telephone technical support from 1 to 3 years
- Replacement of tip / the day following RMA return vs factory RMA
- technical support 24 x 7 vs. 9. 6 M - business hour support F.
- Firmware update
- Even if your product my have a lifetime material warranty, which does not qualify for the technical / troubleshooting / configuration is supported without a contract. With the warranty on the equipment only, the HWC troubleshoot your product just enough to know if it qualifies for a replacement of hardware.
Maybe you are looking for
-
I have a friend who says that he used to be able to share a web address, that he found interesting to a friend with a puch of a button. I always do the old-fashioned cutting and pasting in my webmail but way he says that it is / was a more effective
-
Satellite X 200-21dts: fingerprint reader problem
Hello world I was hoping that you can help me solve my problem. Today I bought the new Satellite X 200 - 21dts, the registration of the user in Protector suite QL I get the message * ERROR of DIGITAL fingerprint SOFTWARE * ' an internal error has occ
-
trying to recover, but used pc has finished start and stops after initial startup logo HP then notes F1, F2 and F9, etc., with a flashing cursor in the upper left corner of the screen. I pressed the F10 key upwards and carried out starting the memory
-
Tecra A8-185: no sound with Vista
I think someones have the same problems as me - under Vista, there is no noise even if the drivers updated. In the audio mixer window, showed that everything was working, but there is always silence :( Someone knows how to deal? :(
-
missing features of config in 2009
I miss some functions configuration after the upgrade of legacy for 2009 code. ' Specifically 'config data registry function.clt"and registry.vi of configuration data. What is the best way to manage this (copy and rename the old lib functions? » Why