QUICK SCREEN FLASHING AND OR FREEZING.

Similar Questions

• On Windows 7, the screen flashes and goes black. It shows that the display driver has stopped working

  I have premium home edition of windows 7 I had a problem with my display driver. The screen flashes and goes black and then turns back on with a message in the bottom right of the screen that reads «display driver stopped responding, but recovered» It has also closed and restarted windows

  Hello

  First, download and install the drivers from the ATI site, if you have already done so, check the graphics card and cabin temperature by opening. This normally occurs when the temperature is too high. Or if a person has overclocked graphics card.

  Thank you

  Nitin Aswani

• dv2500 screen flashes and freezes and the white bars (oh my)

  Have a dv2500, (or dv2530ea if you want really specific). The screen flickers and freezes of once power is on. I also get random horizontal white bars. When the screen freezes happening slowly in white. A small amount of pressure to parts of the monitor case can return to the normal screen that will it stay like that without maintaining a constant pressure can be difficult.

  It is out of warranty.

  This can be corrected? Should I open up? Just a bad connection somewhere maybe?

  -All right, so just in case where any googling leads anyone here I thought I should give the solution, (I have found elsewhere ¬). The problem got worse, anyway. The screen shot for this fade to white mixed with white lines problem to have color of the horizontal lines. The colored lines seemed corrospond to what should be displayed on a single line of the display. Unfortunately, this single line has been posted on all lines of the screen, which gives these horizontal lines. And not intermittently, constantly. Fixable by applying pressure to the screen, but it means to have a screen of work I could not take my hand off the monitor case, not an ideal scenario by a stretch.

  Anyway, it turns out the circuits at the rear of the Panel led made a bad contact somewhere. There was something communicating with display circuit which should not have been in contact with led back panel, give me my damaged screen. To resolve this issue, open the window of degonder the display panel and find the offending area. I did it by applying pressure in specific areas and slide the paper behind the circuit on the rear panel (this obligatory sheet of aluminum at the top of the screen, which was not a problem of lifting, it's just paper). With the bad identified contact area, I could get some plain paper business cards and stuff (quietly) between the plate and the rear panel. Solve the problem. One to the down and dirty round, but very effective and - I believe - very stable one.

• HP w2007 screen flashes and goes out often.

  The computer monitor screen flashes for a second at a time, and frequently.  I have run a check of virus with no viruses found.  I had changed the time of idle mode on the screen saver in the last months, so I'm wondering also if who burned some of the capabilities of the screen.  The monitor IS NOT turn off, it just blinks quickly at various intervals.

  Hello

  Thank you for contacting Microsoft Answers.

  The information provided, we conclude that there could be a problem with the screen itself. Try contacting HP support for further assistance.

• iPhone 6 more screen flashing and does not

  Hello

  For the last few days, my iphone 6 more screen starts flashing from the top and the touch screen doesn't respond. The phone is still under warranty.

  I went to apply here authorized service center in Singapore, they have looked at my phone and said, there is a slight inclination in the phone which will be considered physical damage where it can not be repaired / replaced under warranty, I have to bear the cost.

  Now, as I read on the forums, this is a problem of very well known with the iPhone 6 Plus, also, I don't see no noticeable turn in the phone of my eyes. I'm sure that this issue is not because of any physical damage, but as a result of an internal manufacturing.

  I'm really disappointed with the service of Apple. I don't know what to do now. Should I try to go to any other authorized service center and see what they say?

  Any advice would be appreciated,

  Thank you

  Rohit

  I started having the same problem with my Plus 6. I took it to the Apple store today and the tech told me that it is a known issue that they see a lot. They hope that Apple will issue a recall notice. My phone is out of warranty, so they would be out swap with a unit refurbished for $329. The real kicker is that he said that they have the same problem with a lot of devices refurbished right out of the box. My options are to keep a phone that keeps flashing and does not or pay $329 for a replacement who may have the same problem that has my current phone. It's really bad assumption of a product!

• My screen flashes and flashing light wireless is gone (laptop)

  Product name: HP Pavilion dv5-1040ep Notebook PC (FM577EA)

  Operating system installed: Windows Vista Edition Home Premium

  Error message: None

  All changes to your system until the problem was happening: None

   

  Description of the problem:

  
  I could not find in HP Support Assistant help some. My screen flashes while I open and move it. Sometimes, it must be almost closed to be visible. It can't Hibernate or restarts, flashing just with movement.

  Partners or not, the blue light that indicates wireless, missing/is gone, but I have wireless, just the light disappeared.

  There is no error message, just that two things that appeared in the material.

  Someone happened to that? How do solve you? What are the parts must be corrected or modified?

  Happy to help you.

  But sad for the question.

  Yes, that means lcd cable needs to be replaced. It s is not easy to do, so I advise you don t feel comfortable to open the unit to go to a repair center.

  This components are very sensitive and can be damaged easily.

  You can use this part number for the lcd to buy a new one, a 484367-001 is not much more expensive and is not an expensive repair.

  On the need for basic wlan led to replace the switch cover and the part number of this one is very cheap in 488316-001 it s too.

  You can easily find these parts on the web.

  Doubts, questions or how to replace these parts just tell if I can advise and help you.

  Best regards

• Cannot view full screen flash and silverlight media after Windows Update

  problems with flash and silverlight Muslim poor after windows update said updated the driver and will not play in full screen right.

  Windows Update told to update the driver of the GUI.  After I did my computer do not play in full screen with flash and silverlight. It makes a square with 3 inches on each side.  previously, it would fill the entire screen.  I already talked to Nivdia and they helped me to install again and it runs right is not their product.  I don't know if it's the Avermedia driver then that is the problem.  I have windows vista 32 bit.  When I try to click with the right button on the silvery light, it causes the failed computer.  I uninstalled flash light and silver and it does not solve the problem.

  Windows Update told to update the driver of the GUI.  After I did my computer do not play in full screen with flash and silverlight. It makes a square with 3 inches on each side.  previously, it would fill the entire screen.  I already talked to Nivdia and they helped me to install again and it runs right is not their product.  I don't know if it's the Avermedia driver then that is the problem.  I have windows vista 32 bit.  When I try to click with the right button on the silvery light, it causes the failed computer.  I uninstalled flash light and silver and it does not solve the problem.

  ===================================
  It might be worth a try to do a system restore to
  an hour before installing the updated video driver.

  With the help of the Windows Vista system restore
  http://www.howtogeek.com/HOWTO/Windows-Vista/using-Windows-Vista-system-restore/

  Volunteer - MS - MVP - Digital Media Experience J - Notice_This is not tech support_I'm volunteer - Solutions that work for me may not work for you - * proceed at your own risk *.

• Screen flashes and changes made to vista Basic, then flashes back to aero?

  the scheme of Visual problems with opening the images photo gallery / video folders, flashes and changes to vista Basic, then flashes back to aero? the ball of information in the taskbar windows photo gallery pid States 7868 can someone help me?

  Hello theplantpot,

  Thank you for your response.

  You can check the link below, located on the support site provider of software for more information about the program and Aero under the output video heading problems and related issues:

  http://wiki.videolan.org/WindowsFAQ-1.1.x

  Alternatively, you can view the link below, with the steps to solve the problem:

  http://Forum.videolan.org/viewtopic.php?t=32513

  If the problem persists, you can also try to contact the software vendor for more information about the configuration of the program.

  http://www.videolan.org/support/

  I hope this information is useful.

  Thank you

  Mary
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think.

• 30' cinema screen flashes and off permanently.

  Since the upgrade of RAM (over the w/e) in 2008 Mac Pro the 30 "cinema display has flashed continuously (power), he stopped that if I held my finger nearly walking off button on the side of the screen. Also connected is a screen 23 '' (unchanged). " I checked all sources of energy, etc - everything seems OK, I also put the button of the screen to "do nothing".

  After permutation of the entries for both the 30 screens "Cinema screen but don't blink not now seems not properly shut down, also during the passage of equipment on again once the office and screen saver as chosen by me have reset to a default of Apple." All is very disconcerting and frustrating. All advice and suggestions will be appreciated.

  I came across this problem with the 30 "movie poster - it turned to disable the operating system power and the monitor brightness control did the trick.

• HP 2509 m screen flashes and turns off using a HDMI Cable entry

  I have problems with my new HP2509m monitor. When I connect to my cable box using the HDMI connection the screen image flashes for a few seconds and then goes black for a few seconds and continues to do so. The time interval varies from May 3 to 6 seconds in each phase.

  It's the second monitor I got that this behavior. When I bought my system in October I ordered the 23 "monitor and it worked fine with the HDMI input, but I had trouble with the PC and he traded. The 2509 was introduced at the same time so I decided to share my monitor 23 "to 25", but now I'm regretting this decision. The main reason I bought the extra monitor should have the opportunity to move to the HDMI input for TV viewing, save space in my office.

  I tried the monitor using the same HDMI cable plug into the HDMI from my computer and the light is very good, so it seems to be a problem with the signal from the cable, but everything worked with the 23 "monitor leaving I think there is an issue with tuner HDMI monitor 2509.

  I searched the documentation on the HP site and google search but have found nothing of the sort. Someone has seen this and is there a solution for this? I like to keep the monitor. Thank you.

  Message edited by JudgeLeo on 03/12/2009 20:00
  Message edited by JudgeLeo on 03/12/2009 20:03
  Message edited by JudgeLeo on 03/12/2009 20:03

  Apparently, I was early to the part of the questions of this monitor.

  It turns out that the monitor is not compatible with the decoder I've had. The box is made by the Asian Development Bank and is capable of displaying 1080I content. 1080I is not the issue but because I can use a HDMI to DVI adapter and connect to the monitor and it works OK; It is, so I don't have the computer plugged into the DVI connector as I wanted.

  My cable provider was kind enough to take the monitor and test. They discovered that one of their old version of (amino) cable boxes works very well with the monitor. They swapped the box and it worked well since.

  I use my cable provider HDMI cable, so I don't know the spec version that is.

  My advice to anyone affected by the flashing HDMI display is to get a HDMI/DVI adapter and try it. They are supplied with a certain monitors so that they are fairly easy to find if you know someone who works in a computer SCIENCE Department. If the monitor displays the signal correctly then the question is probably the cable box or as another poster suggested, the cable can be out of spec.

  It is convenient to have the double monitor as a TV. The image quality is superb, but the sound is not. I do not understand why manufacturers monitor for skimping on the speakers. A monitor with its 'premium quality' would be a point of sale, and buyers would be happy to pay for the upgrade. I don't know about a lot of people like me it's simplify - remove the clutter and cables of our offices. HP are you listening?

• The screen flashes and goes out, error: "intel graphics driver has stopped working".

  Original title: Intel graphic driver

  My computer screen starts flashing, then goes and then this message appears "intel graphics driver has stopped working" when I try to get the answer it says "windows cannot download solution at Thøis" I tried a lot but he continues to themselves, what can I do?

  Hello

  (1) when encounter you the problem?

  (2) have what troubleshooting measures you tried?

  (3) remember you to make changes to the computer before the show?

  You can try the following methods and check the status of the issue.

  Method 1:

  Configure the computer to clean start State to check software conflicts.

  http://support.Microsoft.com/kb/929135

  Note: When the diagnosis is complete, don't forget to reset your computer to normal startup. Follow step 7 of the above article.

  Method 2:

  Uninstall and reinstall the display adapter drivers.

  (a) start Control Panel, click hardware and sound and then click Device Manager.

  (b) to expand the node that represents the type of device you want to uninstall, right click on the entrance to the unit and click on uninstall.

  (c) in the dialog box confirm the device removal, click OK to start the uninstall process.

  (d) when the uninstall is complete, the site of the factory driver download and install the drivers.

  (e) after installing the drivers, install the latest updates.

  http://Windows.Microsoft.com/en-us/Windows7/update-a-driver-for-hardware-that-isn ' t-work correctly

• When you type in an 'active' window, the screen flashes and the cursor is no longer active...

  No matter where I type - in an email, on a Web site, same here to post this question - every few seconds the cursor ceases to be active and I have to click in the test area to put it again until I can keep typing

  Hello

  1 how long have you been faced with this problem?

  2 did you a recent software or changes to the material on the computer?

  Method 1:

  I suggest you to update display drivers by following the steps in the link below:

  http://Windows.Microsoft.com/en-us/Windows-Vista/update-a-driver-for-hardware-that-isn ' t-work correctly

  Check if the problem persists, if she engages in method 2

  Method 2:

  To help resolve the error and other messages, you can start Windows 7 by using a minimal set of drivers and startup programs. This type of boot is known as a "clean boot". A clean boot helps eliminate software conflicts.

  How to troubleshoot a problem by performing a clean boot in Windows Vista or Windows 7 http://support.microsoft.com/kb/929135

  Note: when you are finished troubleshooting, follow step 7, mentioned in the article to start the computer to a normal startup.

  See also:

  Change the settings of the mouse

  http://Windows.Microsoft.com/en-us/Windows7/change-mouse-settings

  Hope this helps you.

• Tecra S1: Screen starts flashing and is now black

  Hello. I have a Toshiba Tecra S1. Its 4 years.

  Last night my screen suddenly started flashing and my computer froze. I had to reboot my computer and then the screen starts sometimes, but mostly it stays black. If splash screens, I have only gently shake the computer until the screen flashes again and the computer crashes.

  Otherwise, it seems that the computer works as it should do.

  Could you please tell my computer can be repaired or should I think about buying a new computer.

  Best regards

  Hello

  In my opinion there would be something wrong with the motherboard.
  Perhaps dysfunction of VGA chip maybe some covers may come into contact with the VGA chip and cause of could short-circuit.
  This could be an explanation why the screen flashes and the computer hangs after a shaking gently.

  But buddy note; Here are just a few suggestions and you should contact the ASP if you want to know what's wrong s and what causes this problem.

  Concerning

• Laptop screen starts flashing and white lines appear

  While working on my laptop of her debut screen flashing and white lines begin to appear in this topic. And sometimes she closes down.my laptop is Acer company. R3 - 471 series.

  Hello

  Sounds like corrupted graphics drivers, or graphic material.

  Update your graphics drivers for your model laptop and the operating system directly from the Acer site.

  Acer:

  http://us.Acer.com/AC/en/us/content/drivers

  See you soon.

• What does it mean when the computer screen keeps flashing and n ot stop?

  My computer screen flashed and won't stop not, but for a few minutes at a time. I can't read emails. I can't connect to the programs. What does that mean?

  Hello

  ·         When the issue started?

  ·         Were there any changes made to your computer before this problem?

  Method 1: Fix the refresh rate.

  See: http://windows.microsoft.com/en-US/windows-vista/Correct-monitor-flicker-refresh-rate

  See also: http://windows.microsoft.com/en-US/windows-vista/Troubleshoot-monitor-and-video-card-problems