R715 not Optimal Memory Configuration

Similar Questions

• PE R710 optimal memory configuration

  Hi, we need to upgrade memory on our R710s. trying to find recommendations for configuring optimal memory for gen 11 servers without losing the memory speed. Came across a doc 2009, saying that we can not go beyond 1 DIMM per channel to 2 RDIMMs x without dropping speed to 1066. I'm sure that, after the updates to the BIOS, than the limit went from 1 to 2 DIMMs per channel. Can anyone confirm or share a most recent doc? Thanks in advance.

  Hello.

  The speed of the memory of each channel depends on the memory configuration. Yes, with the BIOS update as of May 15, 2009; Memory only rank and dual-rank modules supports up to 1333 MHz speed. See General information below.

  • Modules memory single or double-row:
    • One module of memory per channel supports up to 1333 MHz.
    • Two modules of memory per channel supports up to 1066 MHz. (review of BIOS on May 15, 2009, support was added for two modules per channel at 1333 MHz speed.)
    • Three modules of memory through are limited to 800 MHz, regardless of the speed of add-on memory.
  • For modules of memory Quad-rows:
    • One module of memory per channel supports up to 1066 Mhz.
    • Two modules of memory through are limited to 800 MHz, regardless of the speed of add-on memory.

  If the memory modules with different speeds are installed, they won't work at the speed of the modules slower memory.

• PowerEdge R815 optimal memory configuration

  Hello world

  I am in courses run PowerEdge R815 with 128 GB of memory (16 GB 8Sticks) I tried all memory configurations I knew and he always gives me ' the memory configuration is not optimal, press F1 to continue "to reboot.

  I tried

  A1, B1 - A5, B5

  C1, D1 - C5, D5

  who should be the best according to the manual also, but it gives even the same question. Can someone tell me please how to configure this option to solve this problem?

  Thank you

  Riazansary,

  A couple of things that I see that would need to be clarified. What about processors, how you have installed? If you indeed have 4 processors installed, then the minimum number of DIMMS that you can use is 16, as it is necessary to have 4 DIMMS per processor. If you use 2 CPUs (1, 2) then the population would be 4 - A1 and B1 - 4. Table 3-2 on page 94 covers this, it shows that the minimum number of DIMM slots for 2 processors is 8 and 16 for 4 processors. - http://ftp.dell.com/Manuals/all-products/esuprt_ser_stor_net/esuprt_poweredge/poweredge-r815_Owner%27s%20Manual_en-us.pdf

  Let me know what you see.

• Tecra M9: not enough memory to run

  Hello

  I have a problem with an application that freezes with messagebox not "enough memory for the operation".
  I repeat, the problem on 7 different model laptop Tecra M9 with configuration: 1024 + 1024 MB RAM with Nvidia NVS130M.

  I tried to change the virtual with ratio 1.5 * ram, 2 * ram memory... and even without virtual memory... every time the same result, when the memory used by file (visible in the Manager of tasks bargraph) occupies about 1.30 GB, the message box appears an application stopped.
  I did a disk defragmentation, checked the Ram, tried the 3 G option in boot.ini, no way.

  Finally, 'just to be sure', I took 1 Bank of Ram of the laptop, and then, with only 1024 MB of Ram, the problem goes away, the Task Manager indicates a value stabilized to used memory (a bit more then 1 GB).

  I don't think it is the right solution for 'downgrade' the size of Ram, if someone already has this kind of problem?

  Thank you in advance

  Hello

  > Finally, 'just to be sure', I took 1 Bank of Ram of the laptop, and then, with only 1024 MB of Ram, the problem goes away, the Task Manager indicates a value stabilized to used memory (a bit more then 1 GB).

  Hmmm, check if you can run Notepad with another RAM module removed.
  I'm not quite sure but it is possible to m the error could be related to a dysfunction of the RAM.

• Download "not enough memory is available to process this command." When installing umdf.exe

  Hello, I tried to configure this file umdf.exe

  but this error pops up: "not enough memory is available to process this command." "The installation did not complete.
  There is a lot of memory and disk space
  So could someone tell me what to do?

  Hello

  Follow these steps to get the fixed number.

  First copy umdf.exe of "wmp11-windowsxp - x 86 - enu.exe" on your desktop, two methods:

  (a) decompress wmp11-windowsxp - x 86 - enu.exe (ex: with TotalCommander-> Alt + F9) and copy umdf.exe on your desktop

  (b) run the wmp11-windowsxp - x 86 - enu.exe (if you run it will extract the folder folder)
         
  Click Start-> Run-> %Temp% [ENTER]
  Press F3, and then search for "umdf.exe".
  Copy this file to your desktop
  Cancel the installation of WMP11
   
  Rename the following files, it just copy & paste into your command prompt:

  Rename C:\WINDOWS\system32\drivers\wudfrd.sys test_wudfrd.sys
  Rename C:\WINDOWS\system32\drivers\wudfpf.sys test_wudfpf.sys
  Rename C:\WINDOWS\system32\wudfhost.exe test_wudfhost.exe
  Rename C:\WINDOWS\system32\wudfsvc.dll test_wudfsvc.dll
  Rename C:\WINDOWS\system32\wudfx.dll test_wudfx.dll
  Rename C:\WINDOWS\system32\wudfplatform.dll test_wudfplatform.dll
  Rename C:\WINDOWS\system32\wudfcoinstaller.dll test_wudfcoinstaller.dll [ENTER]

  Now run the umdf.exe and reinstall it. After that is finished, connect your phone and your MTP problem is solved.

  Bravo!
  Santosh Narayan

• Dell PowerEdge R720 stuck on memory configuration

  Hello, maybe someone can help. I have a Dell R720 which had to restart Windows updates, once its been a bit problematic in that it sits on the configuration of the memory for about 20 minutes. Last night it never comes not beyond that.

  I read on a forum that it could be a driver of KVM switch problem?

  I also read that you can press ESC after publication and which will bypass this, problem, the server is a domain controller and nobody is there.

  Someone knows something similar?

  Peter

  Hello

  Is anyway to bypass the memory configuration?

  I reinstalled the processors and processors, but its still a problem.

  Any suggestions please?

  Peter

• MS Paint build upwards: not enough memory or resources to complete the operation

  I call this iguana impressive in the painting and I wanted to color. I decided to go for a black and white look and configured settings and chose the black and white, to give me the white instead of color.
  I zoomed to 300% zoom, white selected as color 1 and the third from the right in the second row color 2. Then, I selected the Eraser tool and started colouring the white background on the iguana by using the right button of the mouse.
  I tried several times and each time after about 30-60 seconds MS paint show me this message:

  There is not enough memory or resources to complete the operation.
  Close some programs and try again.

  When this happened, I checked the task manager that I couldn't understand something like that was the case. Apparently, I was using only about 60% of my 2 GB of memory, mspaint.exe using somewhere between 9,000 - 14,000 K according to the Task Manager.

  I tried to open a new mspaint and redo the same thing as above designated: zoom 300%, black and white, Eraser, white as color 1, which other than 2 colors right click, paint using the eraser: after some time, same result.

  What is going on?

  I use an Eeebox EB1012 with 2 GB of RAM, double heart Intel Atom 330, Win7 (naturally)

  EDIT: If this is not clear enough: ms paint would not react after the above mentioned message was posted and I had to end the process using Task Manager.

  Hi DrenchedIguana,
   
  
  Let us try the following workaround and check if this helps us solve this problem.
   
  Method 1.
  Important This section, method, or task contains steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click on the number below to view the article in the Microsoft Knowledge Base:
  How to back up and restore the registry in Windows: http://support.microsoft.com/kb/322756

  Let us, make sure that all instances of MS Paint are closed before performing the following operations:
  1. click on start, run, type regedit, and click OK to start Registry Editor.
  2. navigate to this key
  HKEY_CURRENT_USER\Software\Microsoft\Windows\CurrentVersion\Applets\Paint
  and remove the key from the paint.
  3. exit the registry editor and restart the computer.
  4. start the paint to see if your problem has been resolved.
   
  Method 2.
  If the problem persists then I recommend that you create a new user account and check if the problem exists. If the problem is resolved in the new user account, I advise you to fix the corrupted user profile.
  Difficulty of a corrupted user profile 
   
  I hope this helps.

  Thank you, and in what concerns:
  Shekhar S - Microsoft technical support.

  Visit our Microsoft answers feedback Forum and let us know what you think.
  If this post can help solve your problem, please click the 'Mark as answer' or 'Useful' at the top of this message. Marking a post as answer, or relatively useful, you help others find the answer more quickly.

• C240 M3 blocked "memory configuration and test..."

  Hello

  This server was returned by just us to Cisco, which had lent because it was new.   We try to return to service, but have encountered the following problem.

  At first startup, the server receives as much as 'memory configuration and test..' message.  Just this message, it shows no progress in actually memory test.   After a few seconds it turns off, and then turns upward again, repeat that a few times before sit down you with the "memory configuration and test.." message at the top of the screen, but now also showing the address IP of MMIC inside.   The four led above the power button shows green fixed and switch ID unit than the blue LED power buttons, as they should.

  I can get to the MMIC login screen, but the password to the default password so can't get farther in this direction until we discover the new username/password details.  Unless anyone knows how to reset the default MMIC.

  I tried the following recovery steps...

  (1) if we set the J2065 ' Clear CMOS' jumper, the server doesn't work.  It powers up to the day before, but does not respond when you press the power button.

  (2) to the "recovery" of the J2068 rider don't seem to have any effect, the server does not read the USB key recovery file.

  Any ideas?

  Thank you

  Tony S

  I remove the CMOS battery for a while, put back in place, try again and if still nothing... I would look for a motherboard replacement.

  -Kenny

• County of total memory configured in each cluster

  Hello

  I'm pretty new still, Powershell and PowerCLI, but I'm learning.

  I'm playing with, trying to extract data from my vCenter and its going well so far, with the help of this site and a lot of google'ing

  But now im running into a bit of a problem, I want to count the total amount of memory configured in each cluster. And what I soleved with this code:

  $confimem = get-Cluster |

  Select Name,

  @{N = 'Total configured memory GB'; E = {}

  [Math]: round (($_ |)) Get - VM | %{$_. MemoryMB} |

  Measure-object-sum | (Select sum - ExpandProperty) / 1 Ko, 1).

  }}

  And it gives a good result. But now I'm thinking it's account also all VM in the cluster, which is fed to the wide models and all that. I want to do is to include only the VM that is powered.

  And I was thinking something like: Where-Object {$_.} PowerState - eq 'Receiving'}, but I'm not experienced enough to know how to put this together.

  Any body help me solve this problem? I would be very happy

  Nice day.

  $confimem = get-Cluster | Select Name, @{N = 'Total configured memory GB'; E = {[Math]: round (($_ |))} Get - VM | Where-Object {$_.} PowerState - eq "Receptor"} | %{$_. MemoryMB} | Measure-object-sum | {{(Select-ExpandProperty Sum)/1 Ko, 1)}}

• Server memory configuration

  Hi guys,.

  Ask a question about the configuration of memory on hp gen8 servers.

  Does anyone no matter what the tests with memory configurations show various IE with full bus speed 1333 mhz 1900 mhz bus speed vs.

  I would like to see some comparisons on this topic, but can not find.

  We are running with (only) 128 GB for 1 900 mhz speed, I want to double but then let it go up to 1333 mhz and I don't want to cripple our memory applications running in the cluster.

  Anyone know where I can read on this?

  Cheers!

  Stefan

  find a post pointing me in the right direction here on the forum after some research.

  Re: Sizes mixed memory Dell R710 to reach speeds of 1333 mhz and 800 mhz

• Memory configured

  Hello

  A virtual machine allows more memory than its configured memory?

  For example:

  ESXi host is to have 10 GB of memory. 2 VM are hosted on this. Dv01 & VM02 configured memory is 2 GB.

  (1) if the Application is running inside the virtual machine requires more memory, then Will VM would be able to use memory configured 2 GB of memory conc as host is to have additional 6 GB of memory?

  Hello

  When you say 'configured memory', I guess you are trying to say that it is the memory that you have assigned as you created the virtual machine.

  In this case, not your virtual machine cannot be used more than it is configured with. you increase the memory.

  Please see below the link and image captured from pubs of vmware.

  http://pubs.VMware.com/vSphere-4-ESX-vCenter/index.jsp?topic=/com.VMware.vSphere.vmadmin.doc_41/vsp_vm_guide/configuring_virtual_machines/c_vm_hardware_options_resources_available_to_vm.html

  Hope that helps.

  

• I can't open attachments generated in Excel or Word. Get an error there is not enough memory or disk space.

  MIcrosoft Excel cannot open or save documents more because there is not enough memory or disk space.
  To make more memory available, close workbooks or programs you no longer need.
  To free disk space, delete files that you no longer have need of the disc you save to.

  I have 4.75 TB of disk space available. I tried to close open programs and I can't always open attachments.

  I did a search on google and found some info that seems to suggest that it is a question of MS Excel /Word.
  Read the info on this link:

  • http://answers.Microsoft.com/en-us/Office/Forum/office_2013_release-Excel/Microsoft-Excel-cannot-open-or-save-any-more/961a153e-6c68-4b22-b896-94601a28d7e2?auth=1

  Two comments Anula D'Souza and Gus cops offer different solutions, so try both.

• Apple os 9.3.3 charged down behind my back and now my i phone will not open most of the apps because there is not enough memory.  I see that I have 40 GB of memory left on the cloud over 50.  Question, how can I use my pc to see what has been done

  Apple os 9.3.3 charged down behind my back and now my i phone will not open most of the apps because there is not enough memory.  I see that I have 40 GB of memory left on the cloud over 50.  How can question, I use my pc to see what has been downloaded on the cloud?

  Your question has nothing to do with iCloud. You should remove unnecessary data from your phone to free up about 10% of your phone's storage space.

• not enough memory to download email, have removed many of the emails, emptied the trash, sent files help!

  It keeps giving me the message that it can not download my emails because there is not enough memory. I deleted more except the ones I really want to keep. I deleted trash, sent, what we can do. Except keep towards the top with download them every day. I use my Ipad for most. Or how can I get them to download on their own. I go to 'new' and scroll down to my email address to get new emails.

  I do not know how to compact files

  So I hope you read the article I linked to.

• I just noticed that at the bottom of the content library, it no longer displays "new playlist" that does not mean that I did not enough memory?

  When the new playlist is more to show what this means that there not enough memory left.  My hp desktop computer said I have only 931 GB left.

  The new playlist option is always available under the file menu or by using the CTRL + N keyboard shortcut do not know why the button was taken away in the last update of iTunes.

  

  You can also click anywhere on the bar of the left hand under your existing reading list if there is space, and you will see the option for the new playlist.

  I hope this helps