radial gradient with relative positions and absolute RADIUS length

Similar Questions

• problem with timing cRio and FPGA

  Hello

  I develop software for measure the position of a device using some quadrature encoders.

  What I do uses the FPGA interface to acquire the position, then send usign real number of the meter to a host pc to create a data file. In the RT environment, I create a table with the position and the time that is acquired and using shared variables I send the array to the host PC.

  But I have a problem with the sync. The sampling time is unstable, I use a timed loop to control sampling but after some acquisitions, data sampling period begins to increase, as you can see in the image of attachment file. In the attached picture, I used a period of 250us and after some time gets twice and 3 times longer before you clean the table and begin to create a new table, during the period in 250us again. so the problem is that I should get a stable period in 250us instead of these steps in growing period

  You use the table of construction to add new data points? I suggest to use the function "Initialize the array" and "replace the array element. It will reduce the time it takes from the table of the construction.

  I can't open your code as I have LabVIEW 2010.

• Table with fixed header and the left column

  I created a table in my application with the fixed left column (left most column is fixed and remaining columns are scrolling from left to right). is it possible to create a table with fixed position and fixed left column?

  Suppose there are 50 rows and 10 columns in my paintings, and only 3 columns and 15 rows are visiable on the screen

  (1) when the user scroll left to right left only most of the columns must be fixed. Remaining cap of the table and column scroll left to right and vice versa. also

  (2) when user scroll high high bottems single topic most must be fixed and remaining all lines (with to the left most column) should be scrollable.

  I am able to put in place a point at the top, but not both. Please suggest

  "If I repopulate the value in the cell when user scrolling, shell, I get scrolling effect correctly as it only shows half cell when the user highlight half of the cell."

  Approach using TablelayoutManager display single cells and scrolling would be cell at a time.  And Yes, you will need to override navigationMovement and n of methods appropriate TouchEvent your TableLayoutManager so that he knows when to fill the cells.

  Another alternative is to have four managers, we don't the the upper left corner (the dead angle), one to make the top row (column headings), one to make the left column (row headings), and the other to do the rest (data).  Place all these in a delicate header and line manager.  Only allow the user to scroll the data part.  Have the difficult Manager to listen the scroll events.  Then have the wily Manager add and remove the dummy column and header line managers as appropriate.  Note that these topic fields would not good passes, they would be either there or they would not be displayed. That would give you your 1/2 a scroll of the cell.  And you wouldn't have to substitute anything to detect movement, you would have left the listener do scrolling for you.

• If the CSS layout Position is absolute and its content has been tested with the largest font in the browser with no. overlapping, then safe to USE?

  I found that if I used POTIONING RELATIVE to the CSS layouts and pasted my content in them, each of the displaced patterns.  So with the RELATIVE POSITIONING, I have re-aline formatting CSS with each new pasted content.

  In making the CSS absolute Position and tesing with the largest font in the browser, I did NOT meet the problem of duplication of text between two layout close to each other.

  Can there be additional problems with the help of absolute Positions?  Its looks to its worth the risk.

  see you soon

  If the page is good enough for you with the smallest size text as well as the largest text size, go for absolute positioning. It is certainly easier to place the divs with absolute positioning. The biggest problem with the AP div tags is the text problem you mentioned. I would like text in a few different browsers to make sure it looks ok to you.

• Radial gradient brush and adjustment does not

  Thanks in advance to anyone who knows how to solve this problem.

  I'm unable to create new effects of radial gradient brush or setting. I first experienced this issue to the point 3.6 of Lightroom, but it is always persistent in LR 6 on my Windows 7 PC.

  I just changed a picture of the normal characteristics (JPG, 4128 x 2322 px turned on a laptop Samsung Galaxy S4) and I had asked a color gradient that I wanted to get back to no color and leave the other settings of development. If there is another way to do, I don't know how, but I did click on the Panel of nuance of color under the sharpness slider in the gradient panel edit. Once you click on the color chart a range of Hue/Saturation/Lightness selector will appear titled 'Select a color' with an input field of degree of tint in the lower right corner. I deleted the value in this box and pressing the Enter key believing he would remove the color of gradient, but it did not. Now, the sample of color for this or any other previously defined gradient is visible - but I don't have a sample of color on gradients of news or adjustments. The area of shade of color under the sharpness slider is absent or invisible. Color gradients are not a show-stopper, but I cannot apply any brush, gradient, radial or the setting of any image. Existing setting seems to work as expected, but I can't create new gradients or adjustments.

  The screenshot here shows the view when I have an existing gradient selected on the left and the issue of the missing color on the right sample. He is the culprit of the whole issue or not, I couldn't say no, but since I cannot apply adjustments after you make this single change, I suspect that it is related. I will proceed with more details below, but this is the summary of my problem.

  

  More details:

  After the first encounter this problem, I tried another image with no different results. I then tried Lightroom which presented me with a new problem of restart. In LR 3.6 when I tried to apply an adjustment or gradient image would appear as a full scale of gray ~ 128 but I didn't not measure its value. By selecting a State previous history would return the image but any later attempt to apply an adjustment or gradient resulted once again in gray. I then tried to restart my computer with no different results. Suspecting some core file might have been corrupted I then ran repair on LR 3.6 installation but no change - grayscale even if I tried an adjustment on all images. Not wanting to waste a lot of time to reinstall LR 3.6 I decided upgrade to LR 6 (no creativity cloud) hoping that this file of basic or other setting would be crushed. Without success. After the purchase and download of LR 6 a few hours ago, I tried to open the file and make adjustments. While it is no longer the image into a layer of gray blankets, I am still unable to create a radial gradient brush or setting. I suspected it might be the catalog at this stage and have completed just import and tests of other files with no real difference from above.

  Help, please. Thank you

  Thank you once again Bob. I tried the option restore default Presets before you double click the word color, and the issue of gray Panel is back, though only intermittently. Sometimes he will apply a layer of gray on the image and view point which indicates the middle of the slope, while other times it does not display the layer gray or dowry.

  Oh, I just discovered a few new questions:

  1 choose a new image in the film changes the navigator thumbnail, but not the main cloth in the Center.

  2. when I tried to delete the point of gradient I created (or have tried to create above) I received the following error message (included for the search to find):

  Unexpected error executing the command:

  cr_params_applySettings_lua:

  dng_error_bad_format

  

  Which brings me to this post: Lightroom: problem exporting the images when spotting served

  and subsequently retrieve the catalog and images after the reset of the preferences that worked. I deleted the preferences file and the gradients are now working as expected. The options menu in Lightroom > Edit > preferences > Presets > Reset all default etc etc... not reset these preferences successfully so manually delete the files seems to be the solution.

  -Dan

• Can layers be RELATIVE, rather than ABSOLUTE position data

  I'll have a chance to find an answer to this in the HELP. I have place of the layer anchor in a table, then position the layer. If I then add (or remove) the lines above the anchor, everything on the page go up (or down), but the rest of the layer where it was, to the page, not the anchor.
  
  If there are several layers on the page, it means a wholeot of repositioning every time I do an up-page edition.
  
  Any advice?

  This can help you understand the positioning a little-

  There are 4 different types of positioning:
  Absolute
  Relative
  Fixed
  Static

  Here is a brief explanation of each type of positioning (as of)
  placement of the elements in the page only)...

  Position: absolute (or a / P elements)
  -----------------------
  Does several things-
  1. it "deletes" element of the flow of the code on the page so that
  It can influence is no longer the size or position of any element on the page
  (with the exception of those it contains, of course).

  2. the item to absolute positioning takes its position as the position of the
  his next of KIN * place * element - in the absence of any explicit
  positioned parent, it will be by default to theTag, which is always
  positioned
  at 0,0 in the browser window.

  This means that anywhere in the HTML code of the layer
  appears (betweenand), its location on the screen will not
  change (which means that you have not positioned the A / P element in)
  a table or another A / P element, of course). In addition, the space in
  which
  This item would have seemed if it was not positioned is not preserved
  on the screen. In other words, the absolute position elements do not
  all the space on the page. In fact, they FLOAT on the page.

  Position: relative (or R/P elements)
  ----------------------
  In contrast to absolute positioning, is a relatively positioned page element
  * No * withdrawn from circulation of the code of the page, so it will use the
  Spot
  where it would have seemed based on its position in the code as its
  zero point of reference. If you provide then top, right, bottom or left
  positions
  the style for this element, these values will be used as offsets of
  his
  zero point.

  This means that it any where in the code position relatively
  element appears (, as it will be positioned at this place (it takes into account
  the offsets) on the screen (this is true for any location in the code).
  Is also the space where this element seemed
  preserved on the screen and can therefore affect the implementation of
  succeeding elements. This means that the larger a relatively
  positioned element is the space more force on the page.

  Position: static
  -------------------
  As with the relative position, the static positions also "go with the flow". One
  element with a static position cannot have values for compensation (above, right,
  on the left, downstairs) or if it has them, they will be ignored. Unless explicitly
  positioned, any defect in static positioning div elements.

  Position: fixed
  ------------------
  A page with this style element does not scroll when the page scrolls content.
  Support for this in the elements other than the settings of the page is weird

  There are several other things you need to know:

  1. ANY page can be positioned - paragraphs, images, tables, lists,.
  etc.
  2. the

  tag is a BLOCK-level tag. This means that if it is not
  place or style explicitly otherwise, a) it will always start on a new
  line on the screen and b) she will always force the content to a new line below
  He and c) will always be near the top of the entire width of its container (for example,
  Width: 100%).
  3. the placement of A / P elements * can * affect the BEHAVIOR of others
  elements
  on the page. For example, a 'sex' placed on a hyperlink that will hide
  hyperlink.

  You can see a good example of the difference between the absolute and
  relative positioning here-

  http://www.great-Web-sights.com/g_layersdemo.asp

  You can see a good demonstration of why using layers for a page layout tool
  is dangerous here-

  http://www.great-Web-sights.com/g_layer-overlap.asp

  On this basis, a static div (is no longer a 'sex') would be what you want.

  --
  Murray - ICQ 71997575
  Adobe Community Expert
  (If you * MUST * write me, don't don't LAUGH when you do!)
  ==================
  http://www.dreamweavermx-templates.com - template Triage!
  http://www.projectseven.com/go - DW FAQs, tutorials & resources
  http://www.dwfaq.com - DW FAQs, tutorials & resources
  http://www.macromedia.com/support/search/ - Macromedia (MM) Technotes
  ==================

  "bwilsonduncan" wrote in message
  News:fai5oe$q8t$1@forums. Macromedia.com...
  > I have no chance to find an answer to this in the HELP. I place the layer
  > anchor in a table, then position the layer. If I add later (or
  (> Delete)
  > all the lines above the anchor on the page moves down (or upwards), but
  > the
  > layer stays where it was, to the page, not the anchor.
  >
  > If there are several layers on the page means a wholeot of
  > repositioning
  > whenever I do a up-page edition.
  >
  > Any advice?
  >

• Absolute position and orientation of the camera

  Hey folks, I'm banging my head against the wall trying to figure what I think should be a fairly simple expression.

  I'm trying to get my camera to an animatic of a moderator move offshore, and is not imported correctly on its system at least that the camera is not related to what whether in sequels.

  So, my relatively simple (I thought) solution was to use the term toWorld on a new camera to watch the old one and generate the absolute position and X, Y, Z rotation.  However, nothing I do seems to put the new camera in the right place, and I can't figure out how to make the rotation of key frames work not at all.

  Little information about the project, the camera has separate X, Y and Z position keyframes and rotation keyframes X and Y as well as Orientation (although I want the final device to have X, Y Z rotation keyframes).  The camera is related to a null value which has alterations Y rotation.

  If anyone can help me to collect these expressions I would be so grateful!  Thank you!

  See if this helps:

  position

  C = thisComp.layer ("camera 1");

  C.toWorld ([0,0,0])

  point of interest

  C = thisComp.layer ("camera 1");

  C.toWorld (C.pointOfInterest)

  orientation

  C = thisComp.layer ("camera 1");

  u = C.toWorldVec ([1,0,0]);

  v = C.toWorldVec ([0,1,0]);

  w = C.toWorldVec ([0,0,1]);

  SINB = clamp (w [0], 1, -1);

  b = Math.asin (sinb);

  co. = Math.cos (b);

  If (Math.abs (co.) >. 0005) {}

  c = - Math.atan2 (v [0], u [0]);

  a = - Math.atan2 (w [1], w [2]);

  } else {}

  a = (sinb< 0 ="" -1="" :="">

  c = 0;

  }

  [radiansToDegrees (a), (b) radiansToDegrees, radiansToDegrees (c)]

  Dan

• Apply multiple fills with radial gradient to a single shape - Illustrator CC

  Hi, I'm following this tutorial (http://vectips.com/tutorials/how-to-create-realistic-vector-leaves-in-illustrator/comment-page-1 / # comment - 744800) and I'm step 6/7 where I need to add 3 new fills with a different radial gradient and then apply them to different areas of the worksheet to create a variety of tones gradial.

  However, once I did the new filling I press 'G' to bring up the gradient tool, but when I click inside the leaf area my new filling disappears and the last radial gradient fill that I made is highlighted instead. Hope that makes sense, I want to just apply a gradient of light to the corner of the map light green as the tutorial described in 'Step 7'.

  Help, please!

  I noticed that you do not select anything in the first screenshot.

  In Illustrator, the panels always reflect the attributes of the selection. So maybe that has changed when you selected the object in order to change it?

• What is close-angle and focus distance in radial gradients in CSS?

  Read the reference (http://docs.oracle.com/javafx/2.0/api/javafx/scene/doc-files/cssref.html#typepaint) I found these two values that you can set in a radial gradient definition:
  
  radial-gradient([*focus-angle* <angle>,]?) [* focus-distance * < percent >]? [< point > central]? RADIUS [< length > | < percent >] [[repeat | reflect],]? (< color-stop > [, < color-stop >] +)
  
  Could someone enlighten me what they mean? I wrote a small tool for Visual definition of Gradients (http://88.198.17.44/blog/2012/04/13/it-works-fxexperience-tools-gradienteditor-plugin/) as an extension to the FXExperience tools, and I would include if it makes sense.
  
  Thank you
  
  Toni

  Focus-angle and distance from development are used together to determine the focal point of the radial structure.

  See this image: http://www.webdesign.org/img_articles/6822/gradient.jpg

• Elegant way to cope with the Run-in position and the following text

  Hello

  Looking for an elegant way to deal with Run-in position and the following text.

  Currently, HR 11 corresponds to the heading style run-in and then puts the text on the next line. Because the tape FM, heads of run-in with the following style create a look of two columns, this does not quite.

  Thoughts, I had understand how to take the contents of the running head and precede it in the next paragraph? Otherwise, how do something so simple that to change (in HR) the indent of the paragraph following the trail head... How is that done?

  Thank you

  Sean

  I solved this.

  First of all, my FM source has had a problem with some empty paragraphs, sometimes hiding at the end of paragraph runin. So I replaced these (search for \p\p).

  Then I edited the file > Project Settings > FrameMaker Document > paragraph and changed the withdrawal and the spacing for the two styles involved.

  Thank you

  Sean

• How to distinguish between linear and radial gradients in Javascript

  Hey guys,.

  I noticed that some some scripts im using cant always target linear and radial gradients. I was curious to know why it was and where the information about the time a linear or radial gradient is stored or how it can be accessed. So far, no luck.

  That's what I have so far, it doesn't tell me anything besides a pathItem given has a "GradientColor." as fillColor is, I can not understand the syntax to test whether it is linear or radial.

  #target illustrator
  var doc = app.activeDocument
  
  for(x=0; x<doc.pathItems.length; x++){
  alert (doc.activeLayer.pathItems[0].fillColor);
  }
  

  I tried to fix at the end but there always indefinite returnes.

  .Guy

  . TypeName

  .gradient

  . GradientType

  and another thing I could find in the CS6 refrence guide.

  Advice or direction would be greatly appreciated.

  you're close, you need to target the real gradient object to get its properties

  alert (doc.activeLayer.pathItems[0].fillColor.gradient.type);
  

• To attach the same position with different jobs and organization

  Hello
  
  I have a question, is it possible to attach the same with different position of work and organization.
  
  
  Thanks in advance

  I'm not completely sure what you're asking here. A position is limited to a job and an organization, and this post work and the organization can never be changed. If you want to change the work or the Organization on a post, you must create a new post that is a copy of the former with the update of work or organization.

  When you're picking this position in the form of missions that are assigned by default in the Organization and work on the allocation of the position. Similarly, if you already entered work and org on the transfer you can choose only the positions that match this org and employment.

  Who is?

• Define the pattern fill and gradient with color

  Hi all!
  
  This is my first post in the forum of fireworks. Also, this is the first time I'm using Fireworks 8. It's a bit like Photoshop and Photoshop, I can do a fill with a custom pattern by creating a template and do a 'use as motive' and selecting this model and do a fill with it using the bucket fill and then by selecting the model, and fill with a gradient (such as blue-white)
  
  I'm trying to do the same thing with Fireworks 8, but I don't know how. First of all, I created the template in a file separated and saved as a PNG image then in Fireworks, bucket filling (not degraded bucket) on model and then click 'Other' and opened upward model that I created and I filled the area that I wanted to. Now, this is the part that I can't figure out how to do. My boss is points spaced with 1 pixel between each point. I want their gradient fill and I can not blend them. Any help? Thank you

  Quote:
  Posted by: ODoyle rules
  Hi all!

  This is my first post in the forum of fireworks. Also, this is the first time I'm using Fireworks 8. It's a bit like Photoshop and Photoshop, I can do a fill with a custom pattern by creating a template and do a 'use as motive' and selecting this model and do a fill with it using the bucket fill and then by selecting the model, and fill with a gradient (such as blue-white)

  I'm trying to do the same thing with Fireworks 8, but I don't know how. First of all, I created the template in a file separated and saved as a PNG image then in Fireworks, bucket filling (not degraded bucket) on model and then click 'Other' and opened upward model that I created and I filled the area that I wanted to. Now, this is the part that I can't figure out how to do. My boss is points spaced with 1 pixel between each point. I want their gradient fill and I can not blend them. Any help? Thank you

  Hi all!

  In fact I just understand how do.

  Once I made the filling inside the Rectangle, I flattened selection, took the magic wand to select and did a reverse selection filled with gradient with the color I wanted and I checked in the properties of the gradient tool marked "selection of filling" and it worked. I don't know if there is an easier way to do it, but that's how I thought of it.

  Thank you

• Define a variable with the position of an item and use it to trigger an event

  Hi Edge-heads,

  I want to use the position of a movable object to trigger another object to hide/show.

  I tried implementing a variable using jquery. position() and then by testing this variable.

  It is in compositionReady;

  var pos = ("draggable") .position ();

  If (pos > = 850) {}

  SYM.$("obj1"). Hide();

  SYM.$("obj2"). Show();

  }

  This doesn't seem to work...

  Thank you

  Justin

  Have

  $(e.target) .parent () .position)

  Since you have a symbol empty div containing the image of caterpillar, caterpillars of target position is returned from the enclosing div which is always 0.

• Positioning and use of layers

  Hello

  I'm not very good at CSS and I read a lot of documentation on the positioning, but so far I was not able to fully understand. I'm doing a menu (or something like that), which is located to the right of the image. If I try to do something like this:

  

  The browser window

  Image

  Options (layer)

  OK, easy, but if I try to center the image so that it looks like this:

  

  I get somethng like this:

  

  Part of the documentation on the internet seems to be confusing (maybe I do not understand). One of them said I should put:

  Relative

  Absolute

  .. since childhood (red layer) is inside the mother (the image)... but for me don't work (or sense, shouldn't the Red layer position is 'relative' so that 'relative' father's top and left values?) ...

  So far, the code looks like this:

  < code >

  <! DOCTYPE html PUBLIC "-//W3C//DTD XHTML 1.0 Transitional / / IN" "http://www.w3.org/TR/xhtml1/DTD/xhtml1-transitional.dtd" > ""
  " < html xmlns =" http://www.w3.org/1999/xhtml ">
  < head >
  < meta http-equiv = "Content-Type" content = text/html"; charset = iso-8859-1 "/ >"
  < title > experimental 2 < /title >
  < style type = "text/css" >
  <!--

  
  {#container1}
  
  }

  
  {#Layer1}
  position: absolute;
  
  left: 768px.
  top: 153px;
  Width: 245px;
  height: 67px;
  z-index: 1;
  background-color: #F2F2F2;
  / * for IE * /.
  Filter:alpha(opacity=60);
  / * Standard CSS3 * /.
  opacity: 0.6;
  padding: 10px 10px;
  z index: 999;
  }

  {#Layer2}
  position: absolute;
  left: 768px.
  top: 247px;
  Width: 245px;
  height: 67px;
  z-index: 1;
  background-color: #F2F2F2;
  / * for IE * /.
  Filter:alpha(opacity=60);
  / * Standard CSS3 * /.
  opacity: 0.6;
  padding: 10px 10px;
  }

  
  {#Layer3}
  position: absolute;
  left: 768px.
  top: 341px;
  Width: 245px;
  height: 67px;
  z-index: 1;
  background-color: #F2F2F2;
  / * for IE * /.
  Filter:alpha(opacity=60);
  / * Standard CSS3 * /.
  opacity: 0.6;
  padding: 10px 10px;
  }

  
  {#Layer4}
  position: absolute;
  left: 768px.
  top: 435px;
  Width: 245px;
  height: 67px;
  z-index: 1;
  background-color: #F2F2F2;
  / * for IE * /.
  Filter:alpha(opacity=60);
  / * Standard CSS3 * /.
  opacity: 0.6;
  padding: 10px 10px;
  }

  * {
  do-family: Arial, Helvetica, without serif
  color: #696969;
  }

  
  ->
  < / style >
  < / head >

  < body >

  < div id = "Container1" > <!-PARENT *->
  < img src = "media/image1.jpg" / > "

  < div id = "Layer1" > <!-CHILD *->
  Option 1
  < / div > <!-CHILD *->

  < div id = "Layer2" > <!-CHILD *->
  Option 2
  < / div > <!-CHILD *->

  < div id = "Layer 3" > <!-CHILD *->
  Option 3
  < / div > <!-CHILD *->

  < div id = "Layer4" > <!-CHILD *->
  Option 4
  < / div > <!-CHILD *->

  
  </div> <!-- PARENT **************************************************** -->

  
  < p > < / p >
  < p > < / p >
  < / body >
  < / html >

  < code >

  I appreciate all the help... Thanks for your attention

  All wrong! You use all the way from positioning absolute, and who is liable to wreak havoc with different browsers. There is no relative positioning in your code. Relative Placemnt of the elements is obtained by setting the margins, padding and alignment rules, not by setting absolute coordinates in pixels. For example Center; would focus items horizontally within the parent container element, which in your case means that if applied to the image, it would be centered in the browser. Alignment right at the obvious would be align: right; and so on. you get the idea. It's only that you must learn and understand - a model, which places the items based on their difference in the parent container element.

  Mylenium