RALink bluetoth PCle adapter does not work

I have a serious problem with my PCle of Ralink bluetooth adapter

The device status says Windows cannot load the driver for this hardware device. The driver may be corrupted or missing. (Code 39)

{Unable to load device driver}
HS device driver could not be loaded.
Error status is 0 x %x

Hello:

Several forum members have reported success with this bluetooth adapter by installing the latest version of the driver BT directly from Mediatek (Ralink).

Bluetooth Driver (RT3290/MT7630)
25/06/2014V11.0.754.0Win7 Win8 Win8.1

Tags: Notebooks

Similar Questions

  • RALink RT5390 wireless adapter does not work

    My g6 pavilion laptop wifi adapter was not properly work recently. my internet router and networking are works well as it should, but whenever I restart my laptop, repeat me that there is no link and no other wifi networks when there are clearly other networks because of my neighbors.

    I tried a system restore to solve the problem, but it has no effect and my norton affects the restoration of the system to disable the antivirus.

    I'm stuck on ideas to solve this problem and I don't know much about networking and internet stuff, so I'm pretty powerless here

    Here is a link to my features of laptops if necessary:

    http://support.HP.com/us-en/document/c03136241

    These ralink adapters are simple ol ' sh * t. I don't know if it will be a complete solution for you, but I was pulling with my network card for months and this has proved to be the most effective for my computer. I have a HP Envy luck to be equipped with a Ralink RT3290, Windows 8.

    so...

    Out of the box, my computer was working fine and it connected to the network OK. As soon as I moved further away from the router, I known constant dropouts, and the connection always folds between the low signal strength, to completely disconnect the router, where I had to re - connect manually there. This question really frustrating. I use my computer on the top level of my house, and the router is in the basement. If I was getting sick of this fast. Update driver after update driver, no luck. After trying everything under the Sun, I decided I would bite the bullet and I tried something a little bit Orthodox...

    I just uninstalled the driver for my computer. Yes, really. When a component on your computer a driver is stripped, Windows software has a few drivers that will install by default for your material so that it can remain functional on your computer. So, once remove the driver ralink on my computer, windows installed sound driver by default for my network card and... Voila! My connection problems are virtually non-existent at this point. The material is not always the best, but at least I can surf the net in my room without my connection affected by constant stalling.

    Now, other that the light on the button stuck wireless with an orange glow and list my NIC as #10 Device Manager, I always use this driver with minimum questions. Occasionally, he'll forget the connection once I wake the laptop from sleep, but this issue has been much worse with the ralink drivers than without.

    If you are aware of the risk (what is low, to be realistic, this can always be undone and you can always reinstall drivers ralink so that deosn proved to be an effective solution), I will explain in detail how I managed to do.

    (1) open Device Manager (right click the lower left corner in windows 8 and a shortcut appears in the drop-down below)

    (2) find network adapters and display its contents

    (3) make a right click on your wireless network adapter (should be something similar to "Ralink RT5390 802.11b/g/n... ") and click on"Uninstall"in the menu drop-down

    (4) a popup should appear and you should be given the possibility to uninstall or cancel it. Make sure you check "suppression software driver for this device" until you go forward, or Windows re - install the ralink driver.

    -Search for new hardware if your network card is not detected after you have uninstalled it. Your card should appear as "802.11n Wireless LAN card"

    -If you have an installer driver ralink that is newer or equal to the driver that is already installed, you can run the Setup program to remove any driver software remains which is usually overlooked by the device during the uninstallation Manager there from your computer

    -As an option, you can check potential driver leftover files C:\Windows\System32\Drivers. It is important to search for remains that Device Manager / ralink Installer may have missed because it can potentially conflict with the replacement of windows WLAN driver. pilots should have a short name for your adapter (e.g. rt3298.sys); they shouldn't be hard to find. Be careful as well; IT IS WISE TO ALWAYS SAVE no matter WHAT DRIVER SOFTWARE, YOU CAN REMOVE in CASE YOU MAKE a MISTAKE.

    (5) re - enter your information network and you should be good to go!

    I hope that it is of no help to you. People who know nothing about what they will tell you to install the latest driver and yatta yatta yatta this way, because it does not work I had to take the liberty to try to find a solution for these adapters cursed myself. I hope this helps a bit your question!

  • Ethernet USB adapter does not work after update to sierra mac

    Ethernet USB adapter does not work after update to mac sierra.

    Please solve this problem as soon as POSSIBLE

    Hello guatamshah,

    If your USB to ethernet adapter does not work now that you have upgraded to Mac OS Sierra, there are a number of things we can try to get it working again.

    The first thing we want to do is to reset the SMC and the NVRAM on your Mac.
    Reset the management system (SCM) controller on your Mac.

    https://support.Apple.com/en-us/HT201295

    How to reset the NVRAM on your Mac.
    https://support.Apple.com/en-us/HT204063

    If the adapter is not still work after only two resets check to see if your Mac recognizes the device properly in the information system. In the Apple Menu, choose about this Mac, and then click the button 'system report... '. ». Once you have the window open system information, see the USB category on the left.
    OS X: about system information and System Profiler

    https://support.Apple.com/en-us/HT203001

    If she does not appear in the information system, see the articles below.
    macOS Sierra: If a USB device does not work

    https://support.Apple.com/kb/PH25343

    macOS Sierra: check your device's USB connection

    https://support.Apple.com/kb/PH25567

    However, if you do not see the device in system information, you may need to verify that network service appears correctly. In the Apple menu, choose system then Network preferences. You should see an entry similar to "Ethernet" on the left. If no, see the steps in the article below to add. Once add, test to see if your connection works with a disabled Wi - Fi connection.

    macOS Sierra: Add a network service
    https://support.Apple.com/kb/PH25279

    If it does not appear in the network, please let us know what you see on the right when you select the service, and the name of the service as it appears and we can go from there!

    Kind regards.

  • AC adapter does not work with the Qosmio F50-111

    Hello world

    I bought a Qosmio F50-111 this morning.
    The power adapter does not work on my computer (no led lit when connected), but he's working on a Satellite A300 for a working partner.
    And his power works on mine.

    I would like to know if people here have a Qosmio F50-111, the model of power that I have a model 3290-3AC3... I would like to know if it's good.

    Thank you all

    Before you expect an answer here, contact your local dealer and clarify this situation. You can also contact the nearest authorized service provider. They can say with certainty if the power adapter is one that suits or not. If you have the wrong I'm sure you get the right one for free.

  • Wireless network adapter does not work on my Satellite A200

    Hello

    My wireless network adapter does not work under Vista. If I press FN + F8 nothing happens. Wireless communication is always offline.

    What can I do?

    Details:
    Typ: Atheros AR5008X Version: 7.2.0.164
    Laptop Satellite 200
    PSAE6E

    Please help me!
    Thanks in advance!

    Phil

    BIOS bug? I don t think so

    First of all, you must make sure that this isn't a hardware problem. In this case, insert the Toshiba Recovery CD and reinstall the operating system of this device. This will outline the laptop to factory settings. Notes; This would format the whole HARD drive.

    After the new installation, you must activate the WLan switch on the side of books, and you can then use the switch button FN + F8 to select the WiFi network.

    I assume that you have already configured your Wlan router. So the same settings such as the SSID, encryption of WLan, etc. must be defined on the laptop too.

  • Satellite Pro L40 - wireless adapter does not work - Vista

    I recently had some problems with my laptop.
    A couple of weeks, I put in a disc of OpenSuse.
    It's not stable anything, but locked me out of my original Vista operating system.

    I reinstallled Vista Home Basic, but there are a few problems.
    Mainly, my wireless adapter does not work.

    When I flip the button to turn it on nothing happens and it is not recognized in Windows.
    I installed Atheros Driver, but still nothing happens, light is not yet.

    Any advice?

    Hello

    First check the device-> network adapters area manager
    You see the WLan card? Or the unknown device appears?

    If there is an unknown device, then the WLan driver has not been installed correctly or you tried to install a driver badly these two options are possible.

    Remember that your wireless network card? Maybe it was a Realtek WLan card?

    If it's a Realtek WLan card, try the WLan driver from the Realtek website and look for 802.11 g (RTL8187B) chip or you will simply check the page of the European driver Toshiba too the Realtek WLan driver also appeared on the Toshiba page

  • power adapter does not work

    I bought this point aprox. 9/10 months of Tesco, so I don't know if I have coverage?

    Printer all-in-one of HP Photosmart Plus - B209a

    power adapter does not work and I am loan owner hp printers and don't want to splash out on another.

    Help, please...

    Hello

    You should still be under warranty, but if not, you should be able to buy one from HP parts Surfer.

    I hope this helps

  • Cannot install WIndows XP SP3 - wireless adapter does not work with any package of service beyond 2.0

    original title: wireless adapter does not work with any package of service beyond 2.0

    I have an AirLiink 101 wireless adapter.  Anyone know how to change the service pack 3.0 for me to update my Windows XP?   Can not install 3.1 without losing wireless connection.

    Thanks for any help.

    If you are on a wireless connection, try to switch to a wired connection and try the download with Internet Explorer.

    UTC/GMT is 06:49 on Wednesday, April 11, 2012

  • WUSB600N wireless adapter does not work if hooked up to Windows startup

    I have the adapter WUSB600N wireless, and I use it with Windows 7 Ultimate 64-bit. I use the latest available driver, 3.0.10.0. When Windows first starts, the adapter does not work properly and is unable to connect to any network, regardless of how long wait. If I unplug it and plug it back after that Windows is already running, I don't have this problem. This does not work when the "reboot" of the machine; only when turning the power off and then on again.

    Do you have an error message when attempting to connect to the wireless network?

    Try to uninstall and reinstall the wireless card and see if that helps you.

  • Windows 7 message pop-up cigarette... "local area connection adapter does not work correctly. Problems related to the pilot experience or material"what the devil does that average and that the devil can do?

    When I logged on this morning, Windows 7 gave me the following message... "The connection to the local network problems hardware or driver. For connection to the local network adapter does not work correctly. "My Windows offered solution was go using Windows.  Help

    Hello

    Try to uninstall and reinstall the network adapter drivers.

    Download the latest drivers from the card manufacturer support page.

    Download the drivers and extract them to a folder of your choice.

    In Device Manager, right-click on the adapter.

    Click Update drivers and choose her browse my computer for drivers.

    Choose let me a list of choices, click on disk and point to the folder with the drivers.
    ---------------------------

    Computer network health.

    Check the Device Manager for the entry of valid card of the wire.

    http://www.ezlan.NET/Win7/net_dm.jpg

    If there is no valid entry, remove any entry from fake and re - install the drivers for the wireless card.

    Check network connections to make sure that you have a Local Area Connection icon/entry, and that the properties of the icon (right-click on the icon) are correctly configured with the TCP/IPv4 protocol in the properties of network connections.

    http://www.ezlan.NET/Win7/net_connection_tcp.jpg

    Connect you to the menu of the router from a work computer and make sure DHCP is on, and it is configured to assign IPs which can cover the number of computers that are connected (a bit more will be even better).

    Turn off the computer and the router, reset the router and the computer.

    Right-click on the wireless network connection card, select status, details and see if she got an IP address and the rest of the settings.

    On the State of intellectual property.

    TCP/IP and its variables usually look like this.

    Right-click on the wireless network connection card, select status, details and see if she got an IP address and the rest of the settings.

    Typical TCP/IP status looks like this.

    http://www.ezlan.NET/Win7/status-NIC.jpg

    Description is the data of the card making.

    Physical address
    is the MAC of the card number.

    The xx must be a number between 0 and 255 (all xx even number).

    YY should be between 0 and 255

    ZZ should be between 0 and 255 (zz all the same number.)

    The date of the lease must be valid at the present time.

    * Note 1.
    IP that starts with 169.xxx.xxx.xxx isn't valid functional IP.

    * Note 2 There could be an IPv6 entries too. However, they are not functional for Internet or LAN traffic. They are necessary for Win 7 homegroup special configuration.

    ------------------------

    Also, make sure that the software firewall on each computer allows free local traffic. If you use 3rd party Firewall on, Vista/XP Firewall Native should be disabled, and the active firewall has adjusted to your network numbers IP on what is sometimes called the Zone of confidence (see part 3 firewall instructions

    General example, http://www.ezlan.net/faq.html#trusted

    Please note that some 3rd party software firewall continue to block the same aspects it traffic Local, they are turned Off (disabled). If possible, configure the firewall correctly or completely uninstall to allow a clean flow of local network traffic. If the 3rd party software is uninstalled, or disables, make sure Windows native firewall is active .

    Jack-MVP Windows Networking. WWW.EZLAN.NET

  • Wireless adapter does not work.

    Original title: wireless

    I install win7 in my fujitsu siemens AMILO Li 1718 model system, all the drivers are installed but I have problem with my wireless, wireless is not see the amything all available wireless driver is installed courrently can someone help me solve this problem

    Hi Amy,

    It seems that your wireless adapter does not work.

    There is no Windows 7 drivers for your model. You can check this link for simple information.

    http://support.TS.Fujitsu.com/download/ShowDescription.asp?SoftwareGUID=689AC3EC-583D-4B7F-8D1A-CED2F9D7EED8&info=FTS

    I suggest you to visit the above link and download Vista drivers for your wireless card. Install them in compatibility mode.

    Refer to this link: make sure to run older programs in this version of Windows.

    http://Windows.Microsoft.com/en-in/Windows7/make-older-programs-run-in-this-version-of-Windows

    If the problem persists, I suggest you contact Fujitsu support:

    http://Forum.TS.Fujitsu.com/forum/viewforum.php?f=89&SID=1856691d77caf93b0cf1e8058e951cd4

    I hope this helps.

  • Microsoft Teredo Tunneling adapter does not work correctly and my pc works too slowly to start and stop.

    Original title: hardware device

    Please help me...

    My Microsoft Teredo Tunneling adapter does not work correctly... I tried to reinstall it but it is impossible to install...

    So what to do so adpter may work correctly...

    And my pc runs too slowly (at startup and shutdown also)

    Help help me soon...

    Thank you...

    Hi Harshhh36,

    Usually, after the computer restarts, the drivers install automatically and it will stop the errors.

    You can also refer to the computer or the network card manufacturer's Web site to download and install the latest version of the drivers for the network card.

    You can also check in the updates of windows updates available for the network adapter driver.

    For more information, see the article:

    Automatically get recommended drivers and updates for your hardware

  • VMware Player 6 VM - bridged network (Ethernet/LAN) adapter does not work after upgrade to Windows 10 - known issue?

    Hello

    I upgraded the PC host, but also virtual machines to Windows Pro 10.

    TheVMware Player 6 VM - bridged network (Ethernet/LAN) adapter does not work after upgrade to Windows 10...

    Is this a known issue?

    Thank you!

    Kind regards

    Joe

    SOLVED!


    I uninstalled VMware Player, including the abolition of the configuration files.


    re-installed VMware Player and it worked!

  • Windows 95 Ethernet adapter does not work

    Hello

    I have created a machine virtual windows 95 and followed the instructions exactly in the link below.

    Documentation for VMware for Windows 95

    However, the network adapter does not work.  I have the latest version of VMware tools installed, but it does not seem to include any network card driver.

    I tried to download the driver for AMD PCNET Family Ethernet Adapter (PCI and ISA) from the AMD website, but that doesn't work anymore.  I have a virtual machine running Windows 95.  However, he created an image of a physical machine.  The ethernet adapter works fine on this machine, but there is no driver installed - does not require a apparently.

    If anyone has an idea on how to make the ethernet card works, I would be eternally grateful!

    Here is the configuration I have for the Windows 95 VM I created:

    . Encoding = "windows-1252".

    config.version = '8 '.

    virtualHW.version = "6".

    scsi0. Present = 'TRUE '.

    memsize = "64".

    ide0:0. Present = 'TRUE '.

    ide0:0. FileName = "7Win95.vmdk".

    ide0:0. DeviceType = 'disk '.

    IDE1:0. Present = 'TRUE '.

    IDE1:0. AutoDetect = "FALSE".

    IDE1:0. DeviceType = "cdrom-raw"

    floppy0.startConnected = "FALSE".

    floppy0. FileName = "a":

    floppy0. AutoDetect = 'TRUE '.

    ethernet0. Present = 'TRUE '.

    ethernet0. ConnectionType = "nat".

    ethernet0.virtualDev = "vmxnet.

    ethernet0.wakeOnPcktRcv = "FALSE".

    ethernet0. AddressType = 'generated '.

    Sound.Present = 'TRUE '.

    sound.fileName = "-1".

    Sound.AutoDetect = "TRUE".

    roamingVM.exitBehavior = 'go '.

    displayName = "7Win95."

    guestOS = "win95".

    virtualHW.productCompatibility = "hosted".

    extendedConfigFile = "7Win95.vmxf".

    IDE1:0. FileName = 'D: '.

    floppy0.FileType = "peripheral".

    floppy0.clientDevice = "FALSE".

    IDE1:0.startConnected = 'TRUE '.

    ethernet0.generatedAddress = "00: 0C: 29:66: ff: 4 d.

    tools.syncTime = "FALSE".

    UUID. Location = "56 4 d f3 c8 9 c 66 1 0 b - df 02 c3 6 3rd b 66 c ff 4 d.

    UUID. BIOS = "56 4 d f3 c8 9 c 66 1 0 b - df 02 c3 6 3rd b 66 c ff 4 d.

    cleanShutdown = 'TRUE '.

    Replay.Supported = "FALSE".

    ide0:0. Redo = «»

    Replay.FileName = «»

    vmotion.checkpointFBSize = "21102592".

    ethernet0.generatedAddressOffset = '0 '.

    USB. Present = "FALSE".

    pciBridge0.present = 'TRUE '.

    pciBridge0.pciSlotNumber = "17".

    scsi0.pciSlotNumber = "16".

    ethernet0.pciSlotNumber = "32".

    sound.pciSlotNumber = "33".

    Try changing line ethernet0.virtualDev = "vmxnet' to 'vlance.

    Once the AMD driver is installed and running, THEN you can try to change the vmxnet driver, by repairing the VMware Tools on the guest.

  • My Satellite M40x 295 adapter does not work

    Hello

    My adapter (Liteon model: PA-1750-09) don't work, but if I plug it on during a few minutes and plug it back then it works again for a few minutes.
    Recently, when the adapter worked and my laptop was in sleep mode, I pressed on the button ' ' control from lights.
    Do you know anything about this problem? I buy a new adapter?
    Please, help me.

    SEBI

    Hello

    There are two possibilities:
    The AC adapter is dead and cannot charge the battery or there is something wrong with the electronic notebook.
    Try to remove the battery and unplug the AC adapter.
    Wait several minutes (> 15 min) then connect the battery and the adapter for the laptop.

    If this does not work you can check if only the adapter works badly, but in my opinion there must be something different

Maybe you are looking for