Ramping blamed the parameter in the profile of Stimulus Editor.

Similar Questions

• frequency sweep performance in the profile of stimulus Editor

  Hi all

  I am trying to understand what is the best way to do this.

  I have an output signal. I want to start with a 5V signal, so I want to do it in a sine wave of amplitude of 0.05v starting at 1 Hz and gradually increase the Frequency, squirt up to 500 Hz. I know there is a sinusoidal wave function in the profile of stimulus Editor, but he seems to want to keep the fixed frequency.

  Thank you.

  There are a few options:

  1. your own sinewave sequence that will sweep the frequency while he plays. The integrated sine wave function is just a sequence that you can view and copy edit however you want. Double click in the palette to view the sequence.

  2 use multitasking and the sequence of the sinusoid built-in. The sequence of SineWave takes in a setting for the frequency, but it takes the value by reference. This means that if the value mapped to the frequency parameter changes so that the sine wave sequence runs, the frequency of the sine wave will update, too. This allows you to use a multi - load to run two parallel tasks: to call SineWave and one for the ramp of the frequency variable.

  Attached, is an example to help you make sense of it. Maybe it's not the exact logic you want, but should help you get some ideas going. I hope this helps!

• the substitution of variable in the profile of stimulus Editor

  Hi all

  I want suggestions on how to do it.

  So I put the system definition for one of the signals as model Output1--> channel 1--> PXI FPGA AO1 user

  Generally, the model output has controls the FPGA. However, I would like to substitute the output signal to another value to test a few flaws. I tried to substitute in the profile of stimulus Editor, but it would not work (for obvious reasons). I wonder what I can do to substitute the value of another signal that remove the mapping of model output 1 for channel 1 user whenever I want to test this fault.

  Thank you.

  Great question!

  If you use the new editor of profile of Stimulus in 2011 VeriStand, you can perform insertion for lack of software of a sequence in real time using a set of special functions, fault, and clearfault. Fault function allows you to activate a software problem a specific parameter is mapped to a string of system definition (condition it is faultable) to a specified value. This replaces any source can have this channel mappings. To clear the fault of software, call clearfault on the service.

  You can call these functions directly from the Expression. Here is some help on these and other features, you can call in a detailed sequence.

  For example, imagine that you have the following sequence and ao0 parameter is mapped to the string of PXI FPGA AO0 system definition. This sequence when run would fault the AO0 PXI FPGA channel to the value - 10.0, wait 5 seconds, and then clear the fault on AO0. If the fault is active, all mappings are substituted, and any attempt to set the channel failing of the workspace will also fail. When the problem is resolved, any source mappings will affect again.

  IMPORTANT NOTE: There is a bug in VeriStand 2011 which prevents a sequence of faults in real-time completely a channel if no other channel is currently failing in the system. The solution is to open the software tool Fault Manager of the workspace and the fault of some channels dummy, as a channel not used user, before running your sequence.

  • MySequence.nivsseq
  
  
  • Parameters
  
  
  • AO0
  
  
  • Code
  
  
  • Setup
  
  
  • Main
  
  
  • Expression: fault (ao0,-10,0)
  
  
  • Expression: Wait (5.0)
  
  
  • Expression: clearfault (ao0)
  
  
  • Cleaning

• Is it possible to review the profiles of Stimulus for NIVS2009 offline?

  I have a system inherited from NIVS2009 I need to become familiar with before the conversion to the NIVS2010. I need to see a complete list of Stimulus profiles. It is very inconvenient in the pulse generator in the workspace. If I could cut and paste into a txt file would be sufficient, but it does not seem to allow. Is it possible to export or view files .et1 for review?

  Thanks in advance for any input.

  Yes, Mr President, it is.

  In the getting started window menu bar has an entry that offers transfer.

  The name is a little misleading because we say: Mutat Workspace and the definition of system files. Go ahead and run it and you will see a drop down menu with many more options.

  Thank you

  Tom

• Update of Stimulus Legacy profiles to new editor-in-Chief

  Hello world

  I am currently working on the update of a testbed of Veristand 2011 to 2015 SP1. On the bench that we have a lot of Stimulus profile files that were created with the profile of Stimulus editor inherited.

  Is it possible to update the profile of current stimulus editor files and keep their use?

  By looking at the files, I know they are XML, but for some reason, they are completely different formats. It should be possible, however, the translation from one format to the other quite easily. I'm not saying that's what I'll do, just that it is possible.

  See you soon,.

  Pete

  There is not a conversion utility. Here are a few points to note:

  1. the stimulus inherited profile editor is always delivered with 2015 SP1. You can continue to run the same tests in the new version without converting them. New projects by default will not have this tool in the Workspace menu, but you can add it.

  2. If one of your tests is to read CSV files, the same format works in the new Stimulus profile editor.

  Please let us know if there is a particular reason that you want to convert the files to the new format if the notes above don't help you. Who could help us understand a good path for you!

• Profile of Stimulus call API Veristand leads do not have test

  I wan´t to call a stimulus program profile file. I discovered that there are no VI to do this in the API of the LabVIEW VeriStand (for the profile editor of stimulus inherited such a VI exists). But in the example finder is a VI that uses the API .NET VeriStand Edifier present (http://forums.ni.com/t5/NI-VeriStand/Start-Stimulus-Profile-from-LabVIEW/m-p/1789162). Furthermore, someone created a custom control for the workspace that uses this .NET invoke (http://www.ni.com/example/31335/en/). Two examples of work in general, but I have a problem that I m not able to fix:

  If I use a step of "update model parameters of a file" in the profile of stimulus to change the parameters of a model of the step will fail with the error: ' error:-307650. '. Details: object reference not set to an instance of an object. "This only happens if I use the API of VeriStand .NET managed to call the profile of stimulus. If I start the stimulus of the profile editor profile stimulus this doesn´t error occurs and the update of the model parameter works properly.

  If I delete the step of "update model parameters of a file" the whole stimulus profile goes very well.

  Anyone an idea how to solve this problem or how to call a stimulus with the API VeriStand profile file programmatically? Thanks for your suggestions in advance and have a nice day.

  H.

  I can reproduce what you see. You can very quickly get around this by making a call to the method of StimulusProfile CheckForErrors before his execution. This method is called by the Publisher of profile of Stimulus until it starts to run, and he must have some side effects which causes the update settings not work properly.

• How can I get the profile name in the window title bar?

  I have run several sessions of Firefox with different profiles.
  (I start Firefox with: firefox - ProfileManager-no-remote)

  I would like to have the profile name in the title bar of the window, so when I switch between windows and try to find the good session + Gnome3 acitivities profile, I can see the name of the profile.

  Is this possible in Firefox 10 somehow via configuration settings (subject: config) of a certain extension, or with a command-line parameter?

  See:

  • Nightly Test Tools: https://addons.mozilla.org/firefox/addon/nightly-tester-tools/

  You can have a user agent that is corrupt and which identifies you as Firefox 3.0.3 (rv:1.9.0.3) and Firefox/4.0

  • Mozilla/5.0 (X 11; U; Linux i686; en-US; RV:1.9.0.3) Gecko/20100101 Firefox/4.0 Ubuntu/8.04

  See:

  • https://support.Mozilla.org/KB/finding+your+Firefox+version
  • https://support.Mozilla.org/KB/websites+or+add-ons+incorrectly+report+incompatible+browser
  • http://KB.mozillazine.org/Resetting_your_useragent_string_to_its_compiled-in_default

• HP 250 G3 laptop: the profile settings of Touchpad

  Hello

  I'm unable to make persistent changes to the parameters of the touchpad of my laptop.  (Synaptics V.7.5 on PS/2 Port).  I have the latest version of the driver (April 2016).
  
  Description:
  Using of control panels > properties of the mouse > device settings > settings, I'm able to customize the behavior of the touchpad and apply the changes.  Step by step to the camera settings and clicking on the profile button, I am able to record the custom profile.
  
  These settings display the default whenever I do the following:

  • Restart the computer.
  • Use a mouse, connected to a USB port.
  • Select disable the pointing device internal when the external USB pointing device is attached.

  Also, when I select a different scheme of control panels > properties of the mouse > pointers, that parameter also do not support.

  Are you able to give me advice on how to maintain my settings?

  

  Hello

  Try the following.

  Hold down the Windows key and press R

  In the run box, type regedit and press enter

  In the registry editor, navigate to the following

  HKEY_LOCAL_MACHINE\SOFTWARE\Synaptics\SynTP\Install

  Inside, look for a key named DeleteUserSettingsOnUpgrade

  If it is present, right click on the key and select Edit

  Set the field data of the value 0 (zero) , and then click Ok.

  Close the registry editor.

  Restart the laptop.

  When windows has reloaded, bring the Synaptics setting changes you need in the usual way and save them, and then check if they are now retained after a reboot, etc.

  Kind regards

  DP - K

• Payroll ID must be passed automatically using the profile Options.

  Dear all,

  Please suggest for power condition.

  I've created a new report of employee details where I need to go from the Payroll_ID per_all_assignments_f table.

  We have more 7 payroll in our facility. These wages are set using per_security_profile_id possibility of responsibilities.

  Thus, users attached to specific responsibilities should consider only their payroll in the payroll_id of the report parameter.

  Case 1. How can I pass Payroll_ID parameter using the profile option.

  Case 2. Security > Security profile > profile of payroll, Security tab, if you click on the check box "Show all wage masses" for security, how to pass all payroll_ids.

  Thanks in advance.

  Kind regards

  Afzal.

  Hi amal.

  You should check the Pay_Payrolls_F view and not the table (PAY_ALL_PAYROLLS_F)

  If you are checked from the backend, that define the correct responsibility (via fnd_global.apps_initialise) before trying the query.

  See you soon,.

  Vignesh

• Enter the profile "old_password" function check...

  Environment: Oracle EE on Solaris 10 < something > 11.2.0.3
  
  I am currently using a slightly modified version of the provided password check operation seen in $ORACLE_HOME/rdbms/admin/utlpwdmg.sql to verify new passwords. I need to add logic that checks the new password change in addition to 'x' characters, in my case 4 four.
  
  Of course, I can do if I use a script that calls for the old password and the new password.
  
  However, I would like to have the password to verify the function specified in the profile of the user, so it will be invoked if anyone executes a 'ALTER USER... "to tell SQL * more.
  
  Even if there is an entry for the old password setting, when the function is specified in the profile, the past old_password parameter is always passed as a NULL value.
  
  Is it possible to get the old password sent to the audit function to compare with the new?
  
  I guess it must be clear to the verification of the character.
  
  All available to show a typical auditor than the new passwords have been changed by at least four 4 characters when the password is changed by using all means available workarounds like SQL * Plus, SQL * Developer, TOAD, etc..
  
  Thank you much for the help!
  
  GO GIANTS in Superbowl XLVI in Indy!
  
  -gary

  Hello

  When a DBA changes the password of another user (using the alter user privilege), the old password
  is spent with the NULL value to the function of audit, only the owner user (aka even) will be required to use the
  REPLACE clause to specify the old password in this case, you can make the necessary checks, all the logic
  Is that if a DBA defines the password it 1. does not know the old password 2. has sufficient mind either
  Specify a password, or 3. immediately expired the password for the user is forced to change.

  Greetings,

  Damage

• Needed to enhance the profile defined at the level of responlibility

  Hi I have a procedure to obtain the profile value defind in the level of responsibility.
  I will be RESP id as a parameter to this procedure.
  
  Here, the thing is, I will not offer a simultaneous program to do this. And this procedure will be accessible by another application connecting to the database apps and execution
  It is SO completely a procedure that is managed back-end.
  Now to get this value of profile I used
  fnd_profile.value_specific ('XXPROFILE', NULL, RESP_ID, NULL, NULL, null)
  But it's not getting any value.
  
  Please let me know for other solutions.
  
  Thank you

  Salvation;

  Please check below which could be useful for your question:

  How to set a value of system profile without connecting to Applications [ID 364503.1]
  Script to list the values of a profile at all levels [ID 803587.1] Option
  How to change the value of the Option profile without forms [943710.1 ID]

  Respect of
  HELIOS

• How to export the list of devices in the Profile Manager?

  Hello

  is there a way to export the list of devices in the Profile Manager on a mini mac running OS Server 5.3?

  Thank you

  How to export data from device in the Profile Manager

  How to export a list of devices and their info?

• Try to spend XP to W10. Tried to copy the content of the profile (IE not the profile itself) immediately after installation but no joy.

  Try to get an old laptop XP to a new computer laptop of W10 thunderbird.
  Located existing profile and backed up on external hard drive.
  Thunderbird installed on W10 and before breakfast copied the contents of the old profile folder to the profile under AppData/Roaming/Thunderbird/Profiles/profile.default folder
  Launch thunderbird and it does not recognize the profile, it is as if she is trying to set it up from scratch.
  Then tried to create new profile and copying the contents of the old profile of XP, but it did not work.
  Then looked at the Add-ons, but the lightning it is not present, so could not remove it.
  Any other suggestions?

  C:\Documents and Settings\Fraser\Local Settings\Application Data\Thunderbird\Profiles\elvh5ttl.dfault

  This is not the path of the correct profile for XP.
  Check this article and make sure that really copy you the profile folder.
  http://KB.mozillazine.org/Profile_folder_-_Thunderbird#Windows_2000_and_XP

  I do not understand why you created a second profile. With two profiles, you must always be careful to start Thunderbird with the right profile.

• Where is the profile located in El Capitan?

  I can't find the profile folder, or all records related to Thunderbird after installing under ElCapitan! 10.11 even supported at this stage?

  Hello

  You should be able to find your Thunderbird profiles folder by;

  1. In Thunderbird, go to help, troubleshooting information
  2. In the window that opens, in the title of the Basic application, click on the button record show , next to the profile folder.

  This will then open the profile for Thunderbird folder in your operating systems management Viewer.

  I hope this helps, but if not, please come back here and we can look at another solution for you.

• Can W7 \64 bit\FF42.0\How I move the profiles?

  Everything seems to work perfectly. But I realized that I should be able to find how to move my profile to another drive on my computer somewhere in the profile itself. I've looked everywhere I can think of and can't find this info. If you can tell me where it is, maybe I can manage. But if not, can you tell me how to move the profiles? My os is Windows 7 Pro 64 bit. I am running Firefox 42.0. Your guesses are all correct, except that I'm not sure about the plugin from Adobe. Thanks for any help.

  You can use the Profile Manager to create a new profile on a different hard drive folder by clicking on the button "choose a folder.
  Be sure to select a new empty file and not a folder that already contains files.

  You can transfer files from the current profile folder to this folder.

  • https://support.Mozilla.org/KB/recovering+important+data+from+an+old+profile
  • http://KB.mozillazine.org/Transferring_data_to_a_new_profile_-_Firefox
  • http://KB.mozillazine.org/Moving_your_profile_folder