Re: Satellite A100 - cannot get video off the LCD screen

Similar Questions

• Satellite A100 - display balack after replacing the LCD screen

  Hello

  So I'm trying to fix a LCD on a Satellite A100. The girl I am set as said she accidentally hit the screen with his hand and became black.

  When you turn on the laptop I can here windows activate, nothing is on the LCD screen. It is not the backlight, because I don't see anything on the screen at all. So I bought a replacement LCD screen and that one does not work either. Same question

  I think it is the inverter, any suggestions?

  Could be the sensor cover?

  Thank you! Kyle

  Hi Kyle,.

  Did you buy this new LCD screen to a service provider authorized? I ask this question because it would be interesting to know if it s a Toshiba valid a party or 3rd party a spare.

  Did you check the connection of the LCD cable? There may be a link to lose or the cable itself is touched.
  Theoretically, it might be the FL inverter too, but I doubt that. Otherwise, you'd see something on the screen but very dark.

• Satellite A100 - cannot get an Internet connection

  Hello

  I have a Satellite A100 and I can't connect to internet after seeing my reg / cleaned by uniblue, and for the love of me can't get a connection.

  I eat to get my hub connected to the internet, but my laptop just will not allow connection, it's a MCE and it works perfectly fine. I had so many divergent answers at different addresses, all ways said it that another provider has control or error 678. It seems that it's a question of access between the provider of my IP and my system provider does not communicate through this PROTOCOL and my XP PROFESSIONAL system.

  Can anyone help please?

  Hello

  To be honest your ad is a little difficult to understand, and doesn t contain all important information.
  Can you connect to the Internet through WLAN or LAN?

  What happens now exactly if you are trying to establish an Internet connection?
  Your router can connect to the Internet? What is the status now?

  If you have problems with your internet provider you must contact them directly. They can check your connection and make sure that you use the right connection information.

• Satellite P500 - cannot get sound through the HDMI to the TV

  Hello

  my system is a P500, win7 64 bit, ATI Mobility Radeon HD 4500/5100 Series video card, 4 meg RAM.

  I can't get sound via the HDMI to the TV,
  I've updated all the drivers.

  There is also no noise from interface SPDIF playback devices, it says Conexanant SmartAudio HD ready. Computer laptop speakers and headphone works.

  See you soon.

  Hello

  SPDIF or digital audio (HDMI) output is visible in Control Panel-> Sound-> tab reading?

  If so, mark this device as * default * and test the sound of the TV again.

  Greetings

• BlackBerry Smartphones get video off the POWER unit to the PC? 3GPP to other formats?

  This shouldn't be so hard...  I have a few videos of the devcie I want to transfer them to the hard drive on my PC.  I used the Desktop Manager and when I choose MY MEDIA a Roxio application is launched.  I moved the video of the MY DEVICE to MYMEDIA but which does not actually change the video files on the hard drive.  I did eventually fined the files in a folder MY PICTURES/DEVICES DOWNLOAD but they are in a format that none of my video editing software will import.  So, is there an easier way to import media and it can be saved in one format other than the 3GPP format?

  On your media card, allow the mass storage and move the files of your press simply pass through "My Computer" on your PC when connected via USB.

  See details here:

  http://www.BlackBerryFAQ.com/index.php/How_do_I_add_media_files_to_my_microSD_card%3F

  3gp format is playable in several media players of PC, I think that Quicktime is one. Just use a video converter to transfer in the format you prefer.

• Satellite M30X-129 - no video on the second screen

  I have a M30X-129, which for the most part works fine. However, when I have a second monitor attached (for example, an overhead projector) everything is displayed outside a video/film clip, which appears black. This occurs if Windows Media Player or Realplayer is used. All other programs and images are visible on the external monitor or laptop screen.

  I installed Windows XP Pro on the orig XP Home version. All drivers were installed and updated as required. I thnk I have a Raedon graphics card.
  Any ideas on how to have movies/clips on the second screen?

  Thank you.

  Hello

  Most Windows applications and video cards do not support playback of video files on the screens at the same time. You can try to disable the video signal going to the built in LCD screen and display only through the projector.

• Satellite 2410-303-help with replacing the LCD screen

  Hello
  My screen is dead and must be replaced. Can someone tell me where I can get a replacement and at what price? I live in Mauritius and cannot get spare here.
  Thank you mnay
  Jawa

  Hi Jawa

  In my opinion there is not a lot of options. You can order parts by authorized service partners or order it from some independent PC shop. Check if you can find a partner in your countries, or maybe someone else (they can send you everything you need to). Another way Google a little bit and I'm sure you'll find someone who can send you a new LCD screen for your laptop.

  On the price I can't tell you much because we walked free and the price is different from one country to the other.

• How to turn off the LCD on Satellite L655-1JV?

  Hello!

  I have a * Toshiba Satellite L655-1jJV * and I would like to know how I can * turn off the LCD screen *. I tried to use the F5 key, but it does not give me the option to change (always the LCD on except if I connect an external monitor.)
  Of course, I mean, turn off the lcd screen so that, for example, I rose from the monitor, and I'm listening to music...

  I'm really looking for the answer!

  In s manuals document is clearly described when you use the FN + F5 key combination and has nothing to do with it turn off the LCD screen.

  If you need not display and it should be OFF while you listen to music please change the display settings in power options. In the power settings, there is option turn off the screen. Set it to 1 minute and everything will be OK.

• Satellite R840 - 12 c: cannot manually turn off the WiFi function

  I recently bought a brand new Toshiba Satellite R840 - 12 c Notebook.
  The Wifi light is still "on" and the function key does not work, in other words cannot manually turn off the WiFi feature.

  Although the WiFi feature is still "on" I can't connect to wireless modem. "

  When I go to Device Manager I find conflicts in "other devices" for

  1. network controller
  2 PCI Simple Communications Controller
  3 unknown Device

  Tried updating drivers connecting via ethernet cable to the modem, but nothing helped.

  Can anyone help?

  Hello

  Have you installed the driver WLan?
  The laptop seems to be equipped with the Atheros AR9285 WiFi card and in most cases the Fn + F8 key does not work because the Wlan driver is not installed or is not working properly.

  Recommend first of all remove the network card wireless from Device Manager, then restart the laptop. After restarting again install the new driver Atheros Wlan downloaded for this wlan card.

  Here you can find all the drivers Wlan published by Toshiba:
  http://APS2.toshiba-tro.de/WLAN/?page=downloads

• cannot get audio in the timeline to another video

  cannot get audio in the timeline to another video

  

• Satellite A100: Cannot switch to the internal screen

  I apologize in advance if the answer to this question is easy - I have major concern.

  I am an instructor and yesterday was to use a projector to clients to connect my laptop to a session. All was well at first with the laptop screen and projector showing the image, but one of the participants decided to help me and I lost the picture on my laptop (even if not connected to a projector)

  When I turn on the laptop everthing shows on screen (Toshiba etc.) until I get into Windows, then it shows just the ripple background with no icons, however if connected to a projector is displayed.

  I tried fn F5, but is not offer me options normal and I can't reset it.

  Thanks in advance for any help provided

  I put t know what the problem is here, but using the FN + F5 key combination, you should be able to get the LCD screen only. If it works please check display properties. Perhaps it is - someone has activated the extended view option and the value of LCD as second.

  Check this possibility.

• Satellite A100-049 stops loading at the Windows loading screen

  Unless I opened fully open/almost completely the cover on my Toshiba Satellite A100-049 it will always freeze on screen Toshiba Logo black (first one you see). She has completed half of the blue progress bar that runs along the bottom of the screen. I need and then turn off the button and once again, it becomes work.

  The laptop is only 2 weeks old nine. It's especially annoying since it prevents a scheduled backup to wake the portable computer from Hibernation. I have to leave it on or leave the lid open permanently.

  Help?

  It seems that the title has been changed from the one I posted, nothing wrong with that, but it is no longer accurate. It keeps loading the Windows loading screen, it freezes "before" that date. The Toshiba Logo POST screen, very first, you see when you turn on the laptop.

• Satellite A100-590 PSAA9E freezes on the Toshiba start screen after BIOS update

  Hello.

  Yesterday, I made an update of the BIOS on my Satellite A100-590 PSAA9E 03Z00QGR with the appropriate flash:

  http://EU.computers.Toshiba-Europe.com/cgi-bin/ToshibaCSG/download_driver_details.jsp?service=EU&selCategory = 2 & selFamily = 2 & selSeries = 153 & selProduct = 624 & langua ge = 17 & selOS = 10 & selType = all & yearupload = & monthupload = & dayupload = & useDate = null & mode = userMachines & search = & action = search & macId = & country = all & selectedLanguag e = 17 & type = all & page = 1 & ID = 58477 & DISO =-1 & driverLanguage = 42

  BIOS - 20070709111839.zip

  After flashing, the machine restarted automatically, but unfortunately it keeps now suspended from Thoshiba welcome screen. Also by pressing F2 or F12 will not change anything. It seems that the BIOS is damaged.

  I saw that in the BIOS package are delivered the two files (s10gm590.rom and s10pm590.rom) flash. But just the execution of the BIOS590MP.exe SanAntonion10 a .vbs script starts decides which automatically selects and loads a flash file. Maybe she chose the wrong?

  What should I do now? Is there a way to restore the BIOS, or do I have to send my laptop?

  Thanks in advance

  CARPET

  Hello

  sounds are really serious. Unfortunately, I can just give you the only clue you will get with each user here in the forum:

  Find the nearest authorized service partner (you can find one by using this link: http://209.167.114.38/support/Download/ln_byModel.asp)
  and bring your machine. In addition, you must explain the guys what happened so they can do something for you.

  Good luck buddy

• Cannot get rid of the BIOS password

  Bought an ACER Aspire E1 from an EBAY of ACER store about a year ago. A few weeks ago, I started it and quickly received a BIOS PASSWORD entry. Since that time, the laptop was absolutely worthless. I guess I tried the hardware, software, battery and all I could think of to fix the problem. I tried the MICROSOFT forums. ACER, ASK.COM Forums and forums Forums, forums, forrums and other forums that I could think of to try to resolve the unknown BIOS password. Thanks UEFI.

  I guess short of replacement of the EEPROM on the motherboard (don't think even that would help) which I'd be suspicious to do.

  Cannot get rid of the BIOS password.

  If I contact the ACER Support, they say that it's a hardware problem. I tried (as suggested by ACER support), bringing to STAPLES, BESTBUY, FRYS ELECTRONICS, OFFICE MAX, DATA DOCTORS, and several other 'Repair computer facilities' nothing works.

  IN a WORD, it's a PIECE OF a $400 trash...

  If anyone has any ideas on how to reslove this issue, send me an E-mail, fax, text. or post a reply...

  Thanks for letting me the WIND...

  WMARSH...

  can you post the exact model E1?

  E1 - xxx

• I get an error code whenever I start my computer. I have loaded several packs of registry repair software but cannot get rid of the message. The message bed error loading c:\windows\system32\pofusido.dll the specified module is not found

  I get an error code whenever I start my computer. I have loaded several packs of registry repair software but cannot get rid of the message. The message bed error loading c:\windows\system32\pofusido.dll the specified module is not found

  Hello

  I googled this file pofusido.dll and it could be caused by a virus.

  I would suggest that you disable the restore mode as viruses use it to reinstall set apart them.

  Download and install the free http://www.malwarebytes.org/

  Restart the computer and keep pressing F8 to get into safe mode with network connection.

  Once you have updated Malwarebytes run and see if it can remove the virus.

  So delete all cookies in your internet Explorer.

  Please keep in mind that my answer is based on the information in your message. More the better I can answer, Slan go foill, Paul