Read TXT and separate data

Similar Questions

• Reading and saving data of two serial ports

  Hi, I googled similar questions in the forum, but I don't have an answer for my problem so I'm posting it here.

  I would read and record data of two balances throgh serial ports. I have a drop down menu in VI, I can choose the availabe ports on my pc. But it is still only one that works. So I only get one data scales them.

  I usually get to choose 6 ports, but only one of them works. So I'm wondering if this is something that has to do with my pc or the VI?

  I've attached a screenshot of my VI.

  Thank you =)

  
  

• DVD/CD RW do not read audio CDs or data or save a blank CD, but that it's ok to read and write DVDs

  My DVD/CD RW drive will not respond to CDs of any type, void, audio or data.  It whirs for a few seconds and then more nothing.  No AutoPlay (even if she is selected and in the registry as a value of 1), and if I try to click on the drive, the old hourglass stand forever and if I click on new does not, unless I have the disc, it erases then back to normal.

  The drive works fine for DVD reading and writing.  I tried to little nearly every thread relating to problems of CD, and I ran out of hair out! I uninstalled it, unplugged, repluged, rebooted, reinstalled, you name it! PC has updated the driver when I try to update.  I did all the advice regedit I saw and still nothing!  Anyone?  Please?

  Hello

  You have disk problems as the CD/DVD is actually 4 discs in 1 case (CD & DVD burning and)
  Playback of CD and DVD). So it is not unusual for parts from 1 or 2 to not work so that others do
  correctly.

  A CD/DVD cleaner might help.

  CD have a tolerance + - and your can read/write on the edge outside these discs
  tolerances. They may be delivered, but it is generally more economical to replace the disk.

  Several good info here:
  http://Club.myce.com/

  CD/DVD units
  http://www.myce.com/storage/

  Notes on the troubleshooting and repair of readers of compact disks and CD-ROM Drives
  http://www.repairfaq.org/repair/F_cdfaq7.html#CDFAQ_014

  ===========================================

  This troubleshooting could not help if there is alignment and/or wear issues however it
  a shot.

  Step 1: Please do all the same underneath if you did some before as is often total
  a process that solves the problem.

  Try this - Panel - Device Manager - CD/DVD - double click on the device - driver tab.
  Click on update drivers (this will probably do nothing) - RIGHT click ON the drive - uninstall.
  RESTART this will refresh the default driver stack. Even if the reader does not appear to continue
  below.
  
  Then, work your way through these - don't forget the drive might be bad, could be a coward
  cable or slight corrosion on the contacts (usually for a laptop) and other issues.

  Your CD or DVD drive is missing or is not recognized by Windows or other programs
  http://support.microsoft.com/kb/314060 - a Mr Fixit

  Try this fix manually if the Fixit 314060 does not work
  http://www.pchell.com/hardware/cd_drive_error_code_39.shtml

  Your CD or DVD drive is missing or is not recognized by Windows or other programs-
  a Mr Fixit
  http://support.Microsoft.com/kb/982116

  The CD drive or the DVD drive does not work as expected on a computer that you upgraded to
  for Windows Vista
  http://support.Microsoft.com/kb/929461

  When you insert a CD or a DVD, Windows Vista may not recognize the disc
  http://support.Microsoft.com/kb/939052

  Your CD or DVD drive cannot read or write media - A Mr Fixit
  http://support.Microsoft.com/GP/cd_dvd_drive_problems

  CD/DVD drive does not appear in Windows Vista, or you receive this error in Windows
  Vista installation after booting from the DVD (AHCI)
  http://support.Microsoft.com/kb/952951
  Drive CD - R or CD - RW Drive is not recognized as a recordable device
  http://support.Microsoft.com/kb/316529/

  Hardware devices not detected or not working - A Mr Fixit
  http://support.Microsoft.com/GP/hardware_device_problems

  Another possibility is that the cables are loose. Remove ALL power, then make sure that the cables in both
  ends. Remove and replace, do not just tight. For laptops, you can often clean power and
  contacts data with a pencil eraser.

  Some DVD players do not use the Windows default drivers so check with the manufacturer of system and
  manufacturer of device to see if there is a firmware or drivers for your drive if necessary.

  ===============================

  Step 2: You have disc problems as the CD/DVD is actually 4 discs in 1 case (CD & DVD
  Burn and CD and DVD read). So it is not unusual for 1 or 2 operational so that other parts
  do it right.

  Did you follow the Troubleshooting Guide for the reader who still does not work? There are
  the entries in registry that the troubleshooter does not solve and those who "might" be the cause.

  Check with your Maker system and a device for the two possible firmware updates and
  the correct registry entries for your car.

  Here are the keys that I of course are those in question - for the subkeys of the CD/DVD drive
  as there will be other subkeys in these keys. Do not forget to ask specific keys involved as well as
  the parameters.

  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Enum\IDE

  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Hardware Profiles\0001\System\CurrentControlSet\Enum\IDE

  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Control\Class\ {4D36E965-E325-11CE-BFC1-08002BE10318}

  -----------------------------------------------------------------------

  You can probably find more info here and maybe even the exact registry for your CD/DVD settings
  drive from someone with the same model.

  Forums - a lot of expert real help
  http://Club.myce.com/

  CD/DVD units
  http://www.myce.com/storage/

  Use DevManView to locate the CD/DVD in the registry (be careful and do a prior Restore Point)
  nothing change) - find the DevManView device and then make a right click on it free in RegEdit.

  DevManView - free - an alternative to the standard Windows Device Manager, which displays all the
  devices and their properties in flat table, instead of the tree viewer
  http://www.NirSoft.NET/utils/device_manager_view.html

  I hope this helps.

  Rob Brown - MS MVP - Windows Desktop Experience: Bike - Mark Twain said it right.

• Reading file and dump the data into the database using BPEL process

  I have to read the CSV file and insert data into the database... To do this, I created some asynchronous bpel process. Adapter filed added and associated with the receive activity... Adapter DB has added and associated with the Invoke activity. Receive two total activity are available in the process when trying to Test em, receive only the first activity is complete and awaits the second receive activity. Please suggest how to proceed with...

  Thanks, Maury.

  Hi Maury,

  There is no need in step 2 that u mentioned above. I donot find useless a webservice?

  The process will be launched by the CSV file, then using the processing activity, you can put it in the DB.

  There should be no way where you can manually test it by giving an entry. All you can do to test is to put the file in the folder you mentioned when configuring the file adapter.

  You just need to have the composite as below:

  ReadCSVFile---> BPEL--> DB adapter

  And in your BPEL process:

  Recieve--> Transformation activity--> call activity

  Try to work on some samples listed on the oracle site and go through the below URL:

  The playback of the file adapter feature using

  Thank you

  Deepak.

• How to save a calendar I created with the photo and the dates recorded on separate pages?

  How to save a calendar I created in photoshop with the photo and the dates recorded in the form of two separate pages?  When I save in pdf or jpeg, they are automatically save 1 pg with dates and photos on a single page.  This is causing problems when I print.

  Hi there, in which case your printer is not very large, you can also trim down the two versions and print them as separate documents.

  (1) create a guide where you want to split the pages by clicking on the rule (hit control R if they are not displayed) and dragging to the desired location.

  Create the Guide to make it so be precise in the way which divide you your page, and so that no part of the image will be repeated or lost.

  

  (2) select the Cropping tool and adjust the area of culture at half top of your agenda, using the guide you have just made to align with the right place. Press return to complete the harvest.

  

  (3) go in file > save as the. Name the file something like calendar_top and select the desired file format. Press "Save".

  

  (4) once you return to your calendar file, go to the history Panel and select 'Guide to flirting This will bring you to step before you cropped the image.

  

  

  (5) repeat the steps as before to the bottom half of the schedule, once more, using the guide to help you make your growing area.

  

  

  

  Then you would just print each of the two pages individually. The images does not appear in a single document, but if you have Acrobat you could combine the files.

  I hope this helps!

• Reading file from the ftp server and importing data into the table

  Hi experts,
  
  Well, basically, I text with different layout files have been uploaded to an ftp server. Now, I must write a procedure to recover these files, read and insert data into a table... what to do?
  
  your help would be greatly helpful.
  
  Thank you

  user9004152 wrote:
  http://it.Toolbox.com/wiki/index.php/Load_data_from_a_flat_file_into_an_Oracle_table

  See the link, hope it will work.

  It is an old method, using the utl_file_dir parameter that is now obsolete and which is frankly a waste of space when external tables can do exactly the same thing much more easily.

• read txt large files (via Configuration files) takes too long

  Hello

  I want to read files txt large (about 1-8 MB) in memory.

  the structure of the file looks like this:

  [0]
  Shape = 'Point '.
  The size of the grid [nm] = 100,000000
  Dose of pixel [pC] = 0,100000
  Color = 0
  X = 38,169451
  Y = 10,102625

  and for example a 1 MB txt file contains about 8000 of these points.

  with the code current iam using it takes forever to the txt file is loaded:

  

  no idea how to make the code faster?

  Thanks in advance!

  The configuration files of NOR is notorious for its slowness.  It is generally not sensitive because you normally just read small amounts of data, but as soon as it's large structures, it is very sensitive.  OpenG has a config INI palette that allows you to read or to write something else that the low level is these screws NOR and it shows because it can be very slow.

  The solution is not to use these configuration screws instead I highly recommend the read/write of MGI nothing.  MGI says the chain of analysis from scratch and therefore it is super fast.  You can install the tools of MGI using VI Package Manager.

• How to eject my iphone, or player card on my macbook air?  I don't want to disconnect and lose data...

  How to eject my iphone, or player card on my macbook air?  I don't want to disconnect and lose data...

  You won't lose data when you remove an iPhone, unless you're in the middle of the backup or synchronization of the device.

  If you see no activity in iTunes/Photos/etc... Then, it is safe to unplug.

  With a card reader (SD card?) you do drag the desktop icon to the trash. It turns into an arrow when you drag an icon ejector.

  Similarly, you can click Finder on the dock, then locate the reader on the left column and click on the "arrow" to the right of the device to eject it.

• Why the hard disk is divided into partitions of two data (C:Vista and E: Data)?

  I just started a new A200-1V0 and found that disk space is divided into two partitions of sizes equal 'C:Vista' and ' E: Data "(and a small one EISA).

  WHY? What is the logic and purpose? It's not even as if the C:Vista partition is smaller and intended only to the tricks of the 'system' as the root 'Users' (user Documents) is on it also.

  This is the default for Vista (my first use of it), if not, who said that Toshiba could do this without asking me?

  How can I move the root 'Users' in Vista (in the data partition) - if I have two partitions that I might as well use it?

  I can resize partitions in Vista without a utility 3 rd-party (or a complete backup/restore)?

  Thank you

  Hello just YOU

  Please don't be offended because there is no reason for this. You bought the new product with the factory settings. Toshiba and other hardware manufacturer do not know every customer personally and, unfortunately, it was not possible to ask YOU how to set up YOUR laptop.

  Because of this, there is a recovery of product support that allows to configure the HARD disk according to your wishes and needs.

  Please use this DVD and install OS how you want it to be. What recovery procedure starts, you will see CONFIGURATION option on the right side. Click on it and choose the right option.

  Reinstall the OS and enjoy your life. Really, I don't have the time to write on the floors of two partitions, because this is basic stuff and you probably don't want to waste your time to read this.

  Bye and good luck!

• measure the angular speed, angle and trigger using a gyroscopic sensor breakout board and LabView data acquisition

  How to measure the angular velocity, the angle and trigger using a gyroscopic sensor breakout board and LabView data acquisition?

  There is a single channel data acquisition code which measures the angular velocity, angle and flexibility using a gyroscopic sensor breakout board and acquisition of LabView data attached to this, I need a help to creat two-channel data acquisition code?

  Hello

  Attached is a vi that you can use in order to read the measured angular position of an encoder.

  If you need more examples on the tasks that you can develop with NOR-DAQmx and LabVIEW, you just need to open LabVIEW and click Help > find examples > Input and Output material > DAQmx > entry counter.

  Kind regards

• How to use a script to separate data in separate sheets?

  For example, sake, I have three columns: the food consumed (lbs), the Date and Pet (Fido, Penny, whiskers). I want to tease the data part as the data for the first two columns for Penny, Fido and whiskers all appear on different sheets.

  Thanks in advance

  Hi, FCW,.

  I created a use to read in your Excel data file - if you happen to have DIAdem 2010 (11.2) or later, you will be able to use it.  In the case otherwise just load the file but you were before loading so that your 4 data channels are the only ones in the data portal, then run the "DataFileWhisperer.VBS" script in the SCRIPT of DIAdem.

  Brad Turpin

  Tiara Product Support Engineer

  National Instruments

• NEITHER 9207 reading current and voltage at the same time channels

  I have a cDAQ-9178 chassis USB-three cards NI 9217 RTD, three cards 9263 0 - 10V and one the output OR 9207 16 channels analog card. What I m trying with this kind of things, is to read all the analog input channels (information of transducer, temperature, pressure, etc.) and adjust my controls to process with the analog output channels.

  My problem at the moment is the following:

  When I create tasks with DAQmx VI:s, how to create a task that reads current and voltage on the 9207 channels at the same time?

  When I created a task for RTD-channels (16), a task for the outputs analog 0 - 10V (12), a task for the analog input 4-20mA (8) and a single task analog 0 - 10V input (8) I get an error-50103. I think it s because the tasks of current entry and voltagge are trying to use the same CAD at the same time and LabVIEW informs that "The specified resource is reserved. Tasks are to leave so that the analog output task starts first, then I merged all clusters of the error and the rest of the task are started by an order to current input-> input-> RTD input voltage. I get this error after the current enter task started and enter voltage task begins.

  Because I m new on the LabVIEW and stuck in that time, I wanted to try the forum to find answers. I tried to find if someone else was having the same kind of problem, but with a quick search, there was none. I m in a bit of hurry, so I apologize if West a subject with a happy for that and I missed too much according to me.

  Really, the best way to do it is just adding 8 channels of voltage at a task, then 8-channel current, somewhat like this:

  

  Then spread over different channels when you read later:

  

  It should run without error.  It always is multiplexed to sampling, but it will be much faster to create two separate tasks.  There will be between 2ms (mode high speed) and 52ms (mode high resolution) between each playback channels, but it will still be much faster than the permutation of the tasks.

• How to send the SQL for SQL Server statement and return data without using database connectivity Kit?

  Hi, I tried to figure out how to extract data from my SQL Server databases and reading messages and to do some tests with examples, I can get data connection type in my SQL server, but so far nothing helps.  Is it possible to get data from a SQL Server database without using the database connectivity Toolkit?  and if so, how?  are there whitepapers and/or examples of this?  So far, I can't find something that works.  Thank you.

  Jesse - what is your reason for not using the database connectivity Toolkit? It is by far the best way to recover the data.

• Whenever I try to open firefox, windows, it stops and says "data execution prevention has closed firefox. What can I do?

  Can not open google chrome more.  It's really annoying.  Can you help me?

  Please specify your Windows version by clicking on modify under your original message and then change the drop-down lists to indicate the correct version of Windows.

  That means message that programs are trying to write to areas of the process address space that thinks Windows should not be written.  There is a protection that helps prevent malicious code to modify areas of memory that must be read-only and then execution of these regions to do something dangerous.

  Is the error message has an option 'change settings '?  If so, click it, that a dialogue should open the program and you should be able to put a checkbox next to it.

  Otherwise, right click on computer and select properties or press Windows key + R and in the open field, type

  sysdm.cpl

  and then press ENTER.  Select the Advanced tab, and then in the 'Performance' section, click settings.  Select the tab 'Data Execution Prevention'.  What do you see in this tab?

• I want to read a file calibration data

  I have a few calibration to experience data. There are 14 channels, and the data is organized in columns of a spreadsheet 14 lines x 4, where each column is a different constant of an equation of the form y = b1 + b2.x1 + b3.x2 + b4.x1.x2, per channel.

  I need to enter the data in labview, so that I can use it during an experiment. Can anyone recommend the best way to do it? I tried "reading of the file.vi worksheet" but cannot make it work. Recommendations or the sample code? Or do you think it is better to use a text file?

  Thank you

  Dave

  oilyfingers wrote:
  so... Going back to my first question: what method do you recommend? a text (CSV or delimited by tab characters) file

  It does not matter. You just need to wire the correct separator character at the entrance of the separator of function. Therefore, a default tab, if you save the file as CSV and then thread a constant string this entry with the string constant value by a comma.