DVD/CD RW do not read audio CDs or data or save a blank CD, but that it's ok to read and write DVDs

Similar Questions

• Satellite M30X-165: Mat * a UJ - 831 S is not read and write any DVD

  Hello

  the next problem is sticky on the laptop Satellite M30X 165 with the burner Mat * a UJ - 831 S: it can read and write CDs, but is not able to write them to DVD or even read some of the ones I've burned and also read in the same drive. Even at the start of the DVD, it does not start from the recovery DVD, the player starts and slows down very quickly.
  Without doubt, it must be put at the service of repair or someone has other suggestions?

  Could you please tell me how long the repair takes (I know what it takes to install the desktop temporarily used).

  Thank you

  Post edited by: DerSeher
  Using burning software, it detects the DVD, but invite you to an "error of calibration power (037303).

  Hello

  If you cannot use recovery media, I guess that the drive is defective and must be replaced.

• M30x-118 DVD not read and write all formats

  Having problem with m30x-118 (Mat * a uj-820 s). It is not reading the cd - r/rw and DVD + r/rw but read commercial perfectly all cd/dvd - like video dvd or toshiba installation cd.
  While trying to open the disc - "d:\ is not accessible incorrect function" appears.
  Nero recognizes empty disk inserted, but having power calibration error.

  Ramasst running, driver dvd reinstall does not help.

  Hello

  The "power calibration error" message is a problem that occurs with the more recent writers as older. These means of error message that the CD/DVD writer cannot write in the blank CD/DVD because it can t match the output power of the laser power to write CD/DVD.

  Please check this page useful:
  http://www.electricattic.NET/en/mediumspeederror.htm
  http://www.dvdplusvideo.com/dvdguide001.html

  You will find an advice and information why these problems occur.

• Satellite 1410-801: Drive is not read and write many CDs

  Problem with Toshiba DVD - ROM SD-R2212 Drive on a Satellite S1410-801.
  Help, please!
  My drive doesn't read many CDs and I can't write any CD too?

  Hi Wade

  The fact is that readers cannot read all cd or dvd media.
  You should first check different media from different manufacturers.
  As far as I know, you should find a list with the media CD and DVD tested and supported in the user manual.
  I use the TDKs and I m very happy

• "google chrome can not read and write in its data directory '... WHY?

  I used free Windows cleaning tool; theres now load problems. When I reboot works very little?

  [Moved from comments]

  Where did you get this "tool"?

  You have not provided enough information.

  HOW TO ASK A QUESTION:
  http://support.Microsoft.com/kb/555375

• DVD RW drive (D :) will not read or write DVDs)

  My computer can not read and write DVDs and CDs.  Please tell me how to solve the problems.

  Thank you very much!

  Sue

  Hello

  Someone helped me to fix my computer, the problem disappeared.

  Thank you very much.

  Sue

• CD DVD WILL NOT READ OR WRITE. D: IS NOT ACCESSIBLE DUE TO THE I/O DEVICE ERROR

  Toshiba Satellite A - 105 Windows XP media center management with a MashitaDVD/RAM UJ - 841S drive will not read or write CDs D States is not accessible. Cannot be performed because of an i/o device error. However, I can play movie CD via the media center.

  Does anyone have a solution? Thank you!

  Hello

  ·        Was there no hardware or software changes the system just before this problem?

  Please try to follow link below to solve the problem with the DVD player:

  http://support.Microsoft.com/kb/891894

   

  Note: After a repair in method 2 in the link above, make sure you put the computer to start as usual as shown in method 2 in the above article.

  Hope this information helps you solve the problem. Let us know if it helps.

  Thank you and best regards,

  Ramata Thakur

  Microsoft technical support engineer.

  Microsoft Answers Support Engineer. Visit our Microsoft answers feedback Forum and let us know what you think.

• HP DVD Writer does not read or write DVD, but only the CD

  My HP DVD 1135t burner does not read or write DVD but only the CD. What is the problem? Please help me.

  CD/DVD players use different lasers for reading/writing DVD from the CD.  All indications would point to your laser DVD as having failed.  You could try to remove your drive and install it in another computer to see if the problem follows your player or your computer, but my bet is that the drive must be replaced.

  HTH,
  JW

• Could not read or write DVD-RAM

  Even if my material indicates that he can read and write DVD-RAM, all of a sudden I can't recognize discs dvd - ram, that I stored things on front. I followed one of the forums and has released Service Pack 2 and that worked for a while and then stopped working again after a few updates have been installed. I tried again to SP2 and then pushing out, but not joy. No idea how to fix this? I went through Fixit MS and the thing Upper and Lower filters, still no joy.

  Hello

  Step 1: Please do all the same underneath if you did some before as is often total
  a process that solves the problem.

  Try this - Panel - Device Manager - CD/DVD - double click on the device - driver tab.
  Click on update drivers (this will probably do nothing) - RIGHT click ON the drive - uninstall.
  RESTART this will refresh the default driver stack. Even if the reader does not appear to continue
  below.
  
  Then, work your way through these - don't forget the drive might be bad, could be a coward
  cable or slight corrosion on the contacts (usually for a laptop) and other issues.

  Your CD or DVD drive is missing or is not recognized by Windows or other programs
  http://support.microsoft.com/kb/314060 - a Mr Fixit

  Try this fix manually if the Fixit 314060 does not work
  http://www.pchell.com/hardware/cd_drive_error_code_39.shtml

  Your CD or DVD drive is missing or is not recognized by Windows or other programs-
  a Mr Fixit
  http://support.Microsoft.com/kb/982116

  The CD drive or the DVD drive does not work as expected on a computer that you upgraded to
  for Windows Vista
  http://support.Microsoft.com/kb/929461

  When you insert a CD or a DVD, Windows Vista may not recognize the disc
  http://support.Microsoft.com/kb/939052

  Your CD or DVD drive cannot read or write media - A Mr Fixit
  http://support.Microsoft.com/GP/cd_dvd_drive_problems

  CD/DVD drive does not appear in Windows Vista, or you receive this error in Windows
  Vista installation after booting from the DVD (AHCI)
  http://support.Microsoft.com/kb/952951
  Drive CD - R or CD - RW Drive is not recognized as a recordable device
  http://support.Microsoft.com/kb/316529/

  Hardware devices not detected or not working - A Mr Fixit
  http://support.Microsoft.com/GP/hardware_device_problems

  Another possibility is that the cables are loose. Remove ALL power, then make sure that the cables in both
  ends. Remove and replace, do not just tight. For laptops, you can often clean power and
  contacts data with a pencil eraser.

  Some DVD players do not use the Windows default drivers so check with the manufacturer of system and
  manufacturer of device to see if there is a firmware or drivers for your drive if necessary.

  ===============================

  Step 2: You have disc problems as the CD/DVD is actually 4 discs in 1 case (CD & DVD
  Burn and CD and DVD read). So it is not unusual for 1 or 2 operational so that other parts
  do it right.

  Did you follow the Troubleshooting Guide for the reader who still does not work? There are
  the entries in registry that the troubleshooter does not solve and those who "might" be the cause.

  Check with your Maker system and a device for the two possible firmware updates and
  the correct registry entries for your car.

  Here are the keys that I of course are those in question - for the subkeys of the CD/DVD drive
  as there will be other subkeys in these keys. Do not forget to ask specific keys involved as well as
  the parameters.

  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Enum\IDE

  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Hardware Profiles\0001\System\CurrentControlSet\Enum\IDE

  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Control\Class\ {4D36E965-E325-11CE-BFC1-08002BE10318}

  -----------------------------------------------------------------------

  You can probably find more info here and maybe even the exact registry for your CD/DVD settings
  drive from someone with the same model.

  Forums - a lot of expert real help
  http://Club.myce.com/

  CD/DVD units
  http://www.myce.com/storage/

  Use DevManView to locate the CD/DVD in the registry (be careful and do a prior Restore Point)
  nothing change) - find the DevManView device and then make a right click on it free in RegEdit.

  DevManView - free - an alternative to the standard Windows Device Manager, which displays all the
  devices and their properties in flat table, instead of the tree viewer
  http://www.NirSoft.NET/utils/device_manager_view.html

  I hope this helps.

  Rob Brown - MS MVP - Windows Desktop Experience: Bike - Mark Twain said it right.

• CD and DVd won't read and write

  My Cd and Dvd players will not read or write anything...

  Hello

  1 how long have you been faced with this problem?
  2 did you recent hardware or software changes to your computer before this problem?
  3. what happens when you try to play a CD or DVD? You receive an error message?

  Step 1: Run the fix it tool in the following article and check.

  Your CD or DVD drive cannot read or write media
  http://support.Microsoft.com/mats/cd_dvd_drive_problems/en-us

  Step 2: Update driver CD player or DVD and check.

  Reference:

  Updated a hardware driver that is not working properly
  http://Windows.Microsoft.com/en-us/Windows-Vista/update-a-driver-for-hardware-that-isn ' t-work correctly

• Satellite M100 - can only read and write CDs.

  Hello
  I use a Satellite M100 Version PSMA0L-18203E on windows xp sp3. My DVD writer model is HL-DT-ST DVDRAM GMA-4082N.

  The problem is an am able to read and write Cd but when I insert a blank dvd, it displays "Please insert a disk in the drive" so that I am able to use Recovery DVD ROM from Toshiba with no problems. Please help me.

  Hello

  As wrote Al - Ex what program you use to burn discs? I have good experience with Nero and CD Burner XP. Can you test with one of them, please?

  In addition, you must also use high quality media. I have good experience with the types of DVD-R Verbatim and TDK.
  What DVD's that you have?

• Brander DVW/RW can read and write DVD double layer dvd

  Hello

  I would like to know if brander DVD/RW can also read and write the DVD DL(dual layer) dvd.

  or I have to buy for that special brander!

  Johan

  What is a "brander DVD/RW?   Support double layer DVD depends on the material.   Try to identify the make and model of the car since the Device Manager and find its specifications.

• When I plug my portable hard drive to the usb port it does not read and display the contents...

  When I plug my portable hard drive to the usb port it does not read and display the contents...

  Hi deaza,.

  Ø Have you connected the USB hard drive to the computer directly or you have used an external USB hub to connect?

  O trying to connect to another USB port to check if it works?

  O the hardrive shows in windows of the computer when you connect it?

  Method 1:
  If you have installed security software, I suggest you to temporarily disable the security software and connect the USB and check to see if the same problem happens. Make sure that you enable the security software after checking.

  Alternatively, you can try to plug the USB key into a different USB port and check if it helps.

  Method 2:
  I suggest trying to launch hardware and troubleshooting of devices and check to see if it helps, here is the link:http://windows.microsoft.com/en-US/windows7/What-to-do-when-a-device-isn ' t-installed-correctly

  Method 3:
  If this does not help, then follow these steps:

  (a) remove all your USB devices. Use the safely remove the feature to turn them off.

  (b) open Device Manager and navigate to the section for USB. Uninstall all USB drives. There should be one for each USB port, and then restart.

  To open Device Manager, go to the link below and follow the steps:

  http://Windows.Microsoft.com/en-us/Windows7/open-Device-Manager

  (c) Windows should re - find all of the devices. If it is not the case, note the error message and let us know.

  You can also navigate to the link below and follow the steps to install the USB device.

  http://Windows.Microsoft.com/en-us/Windows7/install-a-USB-device

  I hope this helps. Let us know the results.

  Thank you and best regards,

  Srinivas R

  Microsoft technical support.

  Visit our Microsoft answers feedback Forum and let us know what you think.

• Satellite L670-112 - SSD slow read and write speed

  Hello.
  I put 120 GB SATA III SSD kingston (read and write above 500 MB/S), but when I run the sequential test I get 150 MB/S read and 107 MB/S in writing. I know SATA II limitation, so should not write and read nearly 300 MB/S?

  Yes, it should at least reach SATA II speeds (close to 270 MB/s).

  Most SSD's 4K sector drives you may need to realign the 512 to 4K sectors using a partition alignment tool (I think that WD have one available).

• How to read and write attributes using the API?

  I'm trying attributes of access (read and write) of the following:

  SequenceFile

  Sequence

  The sequence steps

  When you look at the documentation of the API, TestStand, the following functions are available:

  PropertyObject

  Properties

  Attributes (read-only)

  HasAttributes (read-only)

  Methods

  DisplayAttributesDialog

  I tried to use the SetValString and GetValString commands using the reference of the attributes, but it does not seem that the data is stored in the file.

  I can't find the following information in the TestStand API:

  1. Where the attributes are stored in a property object?
  
  
  2. How can we access through the API?

  No advice and no information is appreciated!

  You must increment the number of changes to the file after that editing the sequence editor (or UI) won't refresh or mark the file, as amended. Use sequenceFile.AsPropertyObjectFile (). IncChangeCount().

  SequenceFile attributes are stored in the SequenceFile.Data, not the object of SequenceFile object. You can change them in the Advanced tab of the properties of the file sequence dialog box.

  Hope this helps,

  -Doug