Reading through computer speakers, even when headphones are connected to the sound

Similar Questions

• Satellite A660: the sound is still coming from the speakers even if headphones are connected

  Hello

  whenever I have connect headset I still sound emitting from Laptop speakers.

  I have looked in the sound options and realtek but can't see a way to fix this.

  It is forward in my old laptop.
  Michael

  Go to: "Control Panel."
  Click on: "Realtek HD Audio Manager".
  With the "stakeholders" tab highlighted
  Click on: "connector settings" (it's the icon of a yellow folder, in the shaded blue, on the upper side right of the screen)
  «Click here: "contextual dialog box enable auto «»
  Click: 'OK '.
  Connect headset
  What pop-up appears, select "headset" as connected component (NOT out line)
  Fact

• Speakers get muted when headphones are connected

  HP TouchSmart 520

  Windows 7

  The built-in speakers put muted when headphones are connected.

  Hello

  I had the same problem recently with the urge of 23 I use at work, so I plugged the headphones in the speaker to the back of the computer. The music now plays only through the headphones.

  When the computer is seen from behind, the speaker on your desire output jack is probably close to the lower right. It looks like your headphone output, but it has a small icon that looks a bit like this:
  (((.)))

  In addition, a member of the forum named emmarose has had the same problem; That's how she solved: "the problem was solved when I deleted and reloaded the sound driver," she wrote.

• I can't get my pictures to download to my iPhone 6 s on my MacBook Air, even when they are connected by cable

  I can't get my pictures to download to my iPhone 6 s on my MacBook Air, even when they are connected by cable.

  What happens when you try?  Import window is empty in Photos for Mac, or if your iPhone is not recognized?

  If import window is empty or does not display do not all the pictures, you probably have iCloud activated on your iPhone photo library.  Then you can't import photos from your iPhone, because they are stored in iCloud and only mirrored on your device.   In this case to upload photos to your Mac using iCloud. You can download the photos from iCloud by using the Web page at www.icloud.com and the Photos.app it.

  What are your settings for iCloud on your iPhone?

• the pop up Windows Defender when you are connected to the internet by dial-up readings; change of system in known application, type of change; running applications, cwindowssystem32mswsockdll, I am disconnected and then reconnected___

  the pop up Windows Defender when you are connected to the internet by dial-up readings; change of system in known application, type of change; running applications, cwindowssystem32mswsockdll, I disconnected and then reconnected.

  I just ran windows update on a large number of files all successful before this happened, it happens when I am connected to the internet, I use dial-up access

  added on 25/11/09 still have the problem mentioned above, even explore two windows are runnibg on the system, or two IE browsers running?

  Added 27/11/09 I ave followed all instructions up to and including thefix tool kb/93623, stiil I have this report of windows Defender quickly appearing twice in a row, then I'm disconnected from the internet. any more ideas thanks sam

  Visit this link:
  http://support.Microsoft.com/kb/936213

• The battery on my Toshiba NB500 has not been charged since one should use it when you are connected to the power. The battery in the tool bar icon indicates charge but is always 0% available.

  The battery on my Toshiba NB500 has not been charged since one should use it when you are connected to the power. The battery in the tool bar icon indicates charge but is always 0% available. What could be the problem and how can I solve it?

  A problem better put to the support of Tosh or their forums, with regard to their equipment, not MS or Win

• Always sound coming from the speakers when headphones are connected

  When I plug my headphones, the continuous sound coming out the speakers with no sound at all through the headset. When I go on manage audio devices, the helmet will appear, but it says that they're disconnected even if they are connected. I know the headset works very well because they work with my phone. I have Windows 8. What can I do?

  Hello. This is usually a driver problem, especially on models having Realtek audio.

  If you need more help please give the complete model name of the laptop.

• Receives sound of digital audio to the speakers on HP a6433w when you are connected to the TV

  Hello, I need a hero, please. I connected my Panasonic TC-L42U5 TV my HP a6433w computer (Windows Vista), using a HDMI cable. Well, I use TV as a computer monitor. My goal is to get the TV to the sound output to my computer speakers, which are plugged into the sound card Realtek. All I really have to audo out on tv is digital coaxial out, and which is connected to the digital in on my hp. But I have no sound. What can I do? Thank you!

  Hello Ptero1,

  Default settings will be put to the analog jacks. You may need to check the settings to make sure they are defined for digital use.

  Maybe this article will help you http://goo.gl/9JATB

• computer not automatically standby (formerly titled "impossible computer automatically sleep when it is connected to the internet with modem cable")

  Hi, I noticed recently that my computer (Windows XP Media Center Edition 2005) is unable to sleep automatically when it is connected to the internet with a cable modem. Change the settings for my current power mode and try a different feeding regime (diagrams of Windows XP default power and power management, I created) only solves the problem for 2 days at most. I also tried to change the settings for the other power plans mentioned, and yet once again, the problem was only set for two days at the most. I also tried turning off my computer, restarting my computer, recording Powercfg /Restore Default policies in Run, saving sfc/scannow in Run, and again, I got the same result. Reset and power cycling the modem cable is not helped either. To help you better understand the problem, for example, if I had the date set for the screensaver set to 1 minute, the time for the monitor to turn off set to 2 minutes and time for your computer set to 3 minutes, the screen saver activate after 1 minute, the monitor turns off after 2 minutes, but the computer would not sleep mode after 3 minutes , even after an hour or more. I tried to check the Task Manager, and I have not noticed any process that would be interrupting the day before. However, I noticed that when I turned on the monitor by moving the mouse, even when the computer was unable to sleep and unplugged the ethernet cable from the cable modem and waited, the computer has entered standby as it should have.  I tried to find a solution for more than a week, contributions for this issue would be greatly appreciated. Thank you for taking the time to read my post. (Update: it seems that the problem is something else then my cable modem.)

  Hello

  Thank you for the update.

  This behavior can occur because of possible conflicts of third-party software, which includes the third-party security software.

  You can also temporarily disable third-party security software and firewalls installed on the system and check the issue.

  If disabling the antivirus software solves the problem, you may need to configure the settings of the antivirus as a result program. Please contact the software vendor for assistance in this regard.

  Note: be sure to enable the security software on the computer after checking the issue.

  Note: When you perform a clean boot, you can activate services for the modem, network card and disable third-party services to check the issue.

  Hope the helps of information. Let us know if you need help with Windows related issues. We will be happy to help you.

• WLAN speed when you are connected to the internet

  I use WRT54G2 V1 Wireless Router. My firmware version is 1.0.04)is.

  I connect to the internet via ADSL.

  Both computers are connected to the router, we have a connection cable, other is connected wireless.

  If I'm not connected to the internet, I can transfer files between them through 1.5MB/s-2MB/s. But, if I'm connected to the internet, the speed drops to 100 KB/s - 200 KB/s. My adsl connection has a bandwidth of 1 Mbps (about 128 KB/s).

  Has anyone faced similar problem? No idea what to do?

  You said that you receive the Internet wireless at 100-200 Kbps (kilobytes per second), but I guess you're saying 100 to 200 Kbps (kilobits per second).  If you actually get 100 to 200 Kbps, so it is faster than your reported 1 Mbps line speed.

  A wireless connection is more important than a wired connection.  If most users, when connected wireless, get only about 50% to 70% of their wire speed.  So I'm expecting a 1 Mbit/s connected to the Internet, you should be able to get 500 to 700 kbps (kilobits per second) = approximately 50 to 70 Kbps (kilobytes per second) when connected wireless.

  When you file transfer from computer to computer on your local network, your speed is limited by 54 Mbps Wireless g your connection speed, which can provide a data rate up to 20 to 25 Mbit/s.  It is clearly much faster that your 1 Mbit/s to the Internet can provide data.  So that explains why the transfer of files on your local network is much faster than your wireless Internet connection.

  So, the only real problem I see is that your speed of your WAN (Internet) port to the wireless local area network computer seems to be slow.  The most common cause of this problem, is the default to reset the router by default after a firmware update.

  If you did not reset to the factory settings since the last update of the firmware, please do it now and see if it solves your problem.  After the reset, you must configure the router again from scratch.  If you have saved a router configuration file, DO NOT use it.

  To reset your router by default, follow these steps:

  (1) turn off all computers, the router and the modem and disconnect from the wall.
  (2) disconnect all the wires of the router.
  (3) turn on the router and let it start up completely (1-2 minutes).
  (4) press in and hold the reset for 30 seconds button, then release it, then let the router reset and restart (2-3 minutes).
  (5) turn the router.
  (6) connect a computer cable to port 1 of the router (NOT to the internet port).
  (7) turn on the router and let it start up completely (1-2 minutes).
  (8) the power of the computer (if the computer has a wireless card, make sure it's off).
  (9) try ping on the router. To do this, click the 'Start' button > all programs > Accessories > command prompt. A black DOS window will appear. Enter the following text: "ping 192.168.1.1" (without the quotes) and press the Enter key. You will see 3 or 4 lines that begin with ' response to... ". "or"Request timed out". If you see "reply from...". ", your computer has found your router.
  (10) open your browser and point it to 192.168.1.1. This will take you to the login page of your router. Leave the user name blank and in the password field, enter "admin" (without the quotes). This will take you to your router configuration page. Note the version number of your firmware (usually found near upper right corner of the screen). Exit your browser.

  If you get this day without problem, try the Setup disk (or configure the router manually, if you prefer) and see if you can get your work and router configuration.

  If you can not ' response to... ". "in step 9 above, your router is probably dead. A report with this problem

  If you get a response in step 9, but cannot complete step 10, is that your router is dead or the firmware is damaged. Related to this issue.

  If you need additional assistance, please indicate your ISP, the make and model of your modem, the firmware version of your router and the results of steps 9 and 10. In addition, if you receive error messages, copy them exactly, and report.

  Please let me know how things turn out for you.

• Satellite A200-1AE: sound from speakers when headphones are connected

  Hello. Sorry for my English.

  I have problem when I started a player (winamp player or a movie or a game with the sound) and I want to change the sound from the speaker to the helmet by plug them into the headphone jack. The sound is still speaker.

  So I just restart this player or the game and then sound is switched to the headphones.

  So in sum up: when I want to listen to the sound of some player I have to plug in headphones first and then start the player in order reverse, the sound is not switched to the helmet line.

  In other laptops with Vista I have check this problem is not to happen.
  Do you have any suggestions?

  Hello Pawel

  I have the Satellite A200 too preinstalled with recovery DVDs. I was very curious and I tested it on my laptop. In my case everything was OK. Through the use of headphones, Laptop speakers are automatically TURNED off. Remove helmet speakers work again.

  I am really confused, and it is really not easy to say what the problem is here. AFAIK in headphone plug it is small, and through the use of headphones this past should disable Laptop speakers. All you can do is check if it happens after clean OS installation, maybe update the BIOS or install the latest driver sound.

  Sorry, but I don't see any other possibilities. If anything maybe you must contact the service in your country. I really can't imagine that this little mixer may be defective but service may only do a check.

  Bye and good luck!

• HP ENVY23 - D6U52AV #ABA: speakers put muted when headphones are connected

  I tried after an option provided in other post but does not solve my problem in windows 10

  Try the following steps to see if they solve your problem.

  1 right-click on the icon sound in playback devices select system tray

  2. click on speakers (no helmet) so no default device makes your default device

  3. click on the recording tab

  4. click on mix stereo click right properties

  5. go to the listening tab

  6 playback through this device make sure that your headset is not selected

  7. repeat the process for your headphones by ensuring that the reading is not through speakers so

  Thanks for the reply with more details.  It is similar in appearance to me that help me in another forum.  But all the measures I mentioned it solve my problem and now I don't see any problem between audio switching between the built-in speaker or headphones.

  Concerning

• Perform a hard reset when you are connected to the computer?

  Hello

  my iPod Touch G 6 seems to have momentarily buggy so I connected it to the computer, after he had died and needed a charge. He didn't start the loading of the iPod screen, so I did a hard reset while it was still connected to the computer. When he turned his back, I had to enter the password on the iPod to unlock the screen before you start synchronizing with the computer.

  Desire to do harm to the iPod? I accidentally unplugged before ejecting several times, so I'm just scared.

  Thank you

  Jesse

  You have no damage to the iPod. If you disconnect the iPod is communicating with the computer, then you can alter the iPod and a restoration will probably be necessary,

• El capitan crashes when you are connected to the internet ONLY

  If not connected to the internet, the computer will run all day without any problem, any help would be great, thanks

  These must be run as administrator. If you have only one user account, you are the administrator.

  Please launch the Console application in one of the following ways:

  ☞ Enter the first letters of his name in a Spotlight search. Select from the results (it should be at the top).

  ☞ In the Finder, select go utilities ▹ of menu bar or press the combination of keys shift-command-U. The application is in the folder that opens.

  ☞ Open LaunchPad and start typing the name.

  In the Console window, select

  DIAGNOSIS AND diagnostic USE information reports ▹ System

  (not diagnose them and use Messages) in the list of logs on the left. If you don't see this list, select

  List of newspapers seen ▹ display

  in the menu bar.

  There is a disclosure triangle to the left of the list item. If the triangle is pointing to the right, click it so that it points downwards. You will see a list of reports. A report of panic has a name that begins with "Kernel" and ends with ".panic." Select the most recent. The content of the report is displayed at right. Allows you to copy and paste to validate all of the content, text, not a screenshot.

  If you don't see any report, but you know, there was a panic, you have chosen diagnostic and using the list of Log Messages. INFORMATION on the USE of DIAGNOSTIC AND choose instead.

  In the interest of privacy, I suggest that, before posting, you change the UUID ' anonymous, ' a long string of letters, numbers and dashes in the header of the report, if it is present (it cannot be). "

  Please do not post other types of diagnostic report.

  I know that the report is long, perhaps several hundred lines. Please report all this anyway.

  When you post the report, an error message may appear on the web page: "you have included content in your post that is not allowed", or "the message contains invalid characters." It's a bug in the forum software. Thanks for posting the text on Pastebin, then post here a link to the page you created.

  If you have an account on Pastebin, please do not select private in exposure menu to paste on the page, because no one else that you will be able to see it.

• Satellite Pro L300D started crashing when you are connected to the projector

  Hi all, I have a Satellite Pro L300D, have since January. In March of this year, it developed a problem.
  He began to turn the power on and off screen until I got the blue screen of death and had to reboot the laptop, also BIOS crashed. He was sent to Toshiba and got sorted.

  I use the laptop in the Church for the presentation to the powerpoint, we use a projector that connects to the video output on the laptop, but it has now begun to crash whenever I connect the projector to your laptop.

  Can I use the powerpoint, switch to the view of presenters and show the presentation of 30 minutes, then the screen goes black for about a second, the laptop and the projector off, then when they come again, I get a message saying that the display driver has been restarted, little after that the screen turns off, and then market / stop about six times before that I get the BSOD.

  Also, if I show a clip AVI or video during the presentation, it will crash soon after or even before its done.

  Have updated the drivers for laptop, I always get a message stating all the drivers are up to date and I am quite at a loss to know what to do next.

  To be honest, I'm so fed up with it that I am almost to the point of buying an Apple Mac Pro and away from Windows-based computers all together, my friends have macs and they never have any problem.

  Someone at - it an idea on what could be the problem?

  RGS
  James

  Hello James

  Can you please tell me what mode you are using for the presentation?
  Is that what this duplication mode (the same image on the LCD screen and the external device) or something else?
  Do you have problems if you use the single external device (LCD screen is OFF)?

  Movie files can be problematic if you run on laptops LCD and try to switch to the external display while the movie is running.