(Redirect) Dell Latitude 10 Miracast 1.3 WDDM does not

Similar Questions

• I have re-installed Windows Vista on my laptop (Dell Inspiron 1525) and now my wireless does not work.

  Hi, I have re-installed Windows Vista on my laptop (dell insparon) 1525 and now my wireless does not work. ive tried re installing driver, but it says operating system not supported. I used the disc that came with the computer of the re install and I even tried to install service pack 1. .

  original title: Wireless problems after install.

  I just tried both, the dell is one that says OS not supported"and the intel, it went very well, but my 'network controller' still have a yellow top thing in Device Manager. and I always wireless. any other ideas? Thank you for the help

  Question...  You have whatever it is listed in the "Network adapters" section of "Device Manager" now?

  While ensuring that the exclamation point is not for your wired network device (plausible) or bluetooth (plausible) and you just need to configure your wireless network to connect to * your * wireless network now.

  You may have to contact Dell to see why none of their drivers receive your wireless device works on the original operating system, what they included.  This could be a hardware problem PURE.

• I just installed windows 7 ultimate 64-bit on my laptop dell inspiron 1501. Now the scrolling does not work on my touchpad. Any ideas.

  I just installed windows 7 ultimate 64-bit on my laptop dell inspiron 1501. Now the scrolling does not work on my touchpad. Any ideas.

  Try the web site of Dell for Win 7 drivers. There may be some here. If it does not exist, you might have to wait until the public release before Dell post...   Mike Hall MVP - Windows Experience http://msmvps.com/blogs/mikehall/

• Dell Latitude e5440 - Samsung 850 EVO mSATA SSD not recognized

  I bought a new 500 GB Samsung 850 EVO mSATA SSD for my Dell Latitude e5440 (running Windows 7 Pro).  The new player was not visible in 'Computer', so I downloaded, installed and ran the software Samsung magician.

  Samsung software shows that the drive is present.  And there is a button "Validate" - I clicked on - and now: ' Drive Health Status: Good ' and ' serial number: true "appears.

  However, the SSD is not visible when I double-click on computer and the Samsung software States:

  a. "AHCI Mode. Disabled (IDE or RAID).  AHCI mode is necessary for the best performance of the SSD. »

  b. SATA Interface s. o. cannot detect SATA interface details.

  c. s. o. OS OS optimization is supported only for disks using an operating system drive.

  Question 1: Activation of this AHCI mode will allow Windows to recognize the SSD?

  Question 2: How do I?

  Question 3: Activate the AHCI mode "switch off" (logout) my HDD 2.5 "?  (I want to keep Windows 7 to 2.5 "HARD disk and install Windows 10 on the SSD to have a dual boot system, until I got used to Windows 10).

  Inside of your battery compartment is a label with your license key Windows 7 OEM on it.  Photograph it.

  Download and prepare a USB key with a copy of Windows 10 TH2 Pro.

  Remove the disk 2.5 "and connect the new drive mSATA.

  Boot the system to the USB key.  10 Windows Installer should be of the presence of the DSS and will allow you to do the installation of Windows 10 - which in turn is almost certainly going to install the network driver suitable for your system without the need to add anything else.

  USE your 7 product key when prompted and you should be all set.

  Once this is done, you can reconnect the disk 2.5 "If you want to do - but remember that 10 installation is done separately from the 2.5 disk".

• Bought a new dell battery and still my laptop battery does not charge.

  Hello.

  I am using a Dell inspiron 1545 for about 3 years now and exactly after 2 years of my purchase, the battery has failed and it began to show me to replace the battery and always informed to contact me dell for a new battery.

  I took this to a lot of trouble, so I simply ignored the message and kept using my battery with my wired adapter. After 4-5 months of such uses, my battery has completely failed and does not give me even even a minute of backup, when I remove the power outlet. Then I realized the importance of a new battery and then bought a new battery from Dell.

  Its the same battery with the same features and also the same type family. After that I removed my faulty battery, I replaced my purchased new Dell battery and realized that my battery works fine. his load well, but at one point, it says "plugged in, but do not load" which is rare for a new battery, that is purchased new.

  

  This is what it looks like now once I removed the plug adapter and when I depend on the backup battery. It provides a backup, but I see a Mark exclamatory yellow next to her. Which I think should not be present. He also says "Low battery" when there are already some 99% battery left!

  I also followed a few steps online

  (1) update the BIOS for the last 2) followed by a few other steps such as uninstall the ACI battery in Device Manager and etc...

  I'd like to get this problem is solved. I use an adapter family PA-12, which is also replaced. So any help on resolving the issue would be appreciated.

  Thank you!

  Hey maxim. I have actually FIXED this month back, problem. and I want exactly help on it so that you can fix it yourself too...

  the problem that is the creation of your battery to display an exclamatory mark is your power settings.

  then follow these steps to get rid of this sign and a battery to work perfectly.

  1) click the icon of your battery (left click), you should see an option called "Power Options more' at the bottom of the pop-up window.

  Click on 'more power Options.

  (2) now, you will be taken to your control panel where you can see all of your power plans and under each plan, you will see an option called "Change plan settings"

  3) click on "Change plan settings" for your active power plan. Now you will be redirected to another window of Control Panel, where you can see two types of power options to get adjusted. in other words, when you battery is connected and when your battery is disconnected.

  (4) do not touch these options, simply click on 'Change power avancΘs' at the bottom left of this window. THIS IS THE AREA WHERE WE HAVE TO FIX!

  (5) after that you click "Change advanced power settings", you will see a POWER options window, go down and then you can see what is called "Stack" with a sign to the left. until it clicks.

  (6) now, you just change the levels for the following values

  --> Critical battery level (you can change it to 10%)

  ---> Low battery (you can change it at 20%)

  Now once who did, YOU will BE No. LONGER SEE THE EXCLAMATIVE MARK on YOUR STACK!

  So I hope it works!

  Answer me when you've managed to fix.

• Dell Dimension 4600 with pack 1 XP does not connect to the cable modem

  Hello, I have a Dell Dimension 4600 older XP. The hard drive is dead and I replaced and then reloaded pack 1 with the intention of making all the revisions on the internet. The problem is that I cannot now connect to the internet via my broadband router directly connected to the computer. It seems that the wizard to connect only wants to use the dial upward and does not connect to the router. Just recompose. It seems to ignore the connection from the router to broadband and wants to use the dial upward only.

  Go to control panel of control/Internet options/connections, then set it - never establish a connection - then click on apply.

• Dell place 11 Pro travel keyboard - touchpad does not

  I bought the DVP11 with travel keyboard, and touchpad not responding after working initially. The keyboard is completely loaded, as is the DVP. All other keys on the keyboard work. Dell tried updating the BIOS support and several parameters of the driver, but no change. Thoughts before I have send the keyboard backwards?

  Mine has started working after the update too. But I think you're right that the problem is related to the battery or charge, touchpad no longer works after that I loaded the keyboard separately and then connected it. There are also some problems of connection between the keyboard and screen, if the screen turned completely open position, so it rests against the back of the keyboard, keys or the touchpad does not work.

• Dell Mini 10 1018 Factory Restore - user does not know how to use the Dell utility

  I was running a starter edition of Windows 7 and decided to go with a picture own factory before moving on to Windows 10. My mistake was thinking that recovery Dell utility would work.

  I created a restore 8G USB key using the included Dell utility. I reboot from the USB and restore to factory. He gets the part of the way through and then seems to get confused, re - access scripts folder TAL and stuck in a reboot loop.

  Help!

  Update - Yes, it's a problem to the user. I did not notice the cleaning Sysprep prompt shortly after the resumption. If it is not allowed to run, Sysprep never ends. I have not seen documentation on this, but in my last attempt, I must have selected the appropriate parameters for the cleaning of Sysprep to get off the machine and let Windows finish the installation.

  Mduh9,

  Glad that you solved it all. Eventhough, 10 Windows can install on your computer and load default drivers. Dell has not any Windows 10 drivers for the mini and did not check Windows 10 for this computer. Make sure that you back up your data before installing Windows 10 in case it does not work.

• Reference Dell E6540 - ATI Radeon HD 8790 M does not appear in the BIOS

  Hello

  I have a Dell E6540, which, according to the data sheet must have a graphics card than ATI Radeon HD 8790 M. but looking in the BIOS, there is no entry in addition to the dedicated graphics card Intel 4600.

  I have the latest version of the BIOS and the latest graphics card driver. I am using 8.1 Windows 64 bit.

  Please let me know if I need to do something else to make it the primary video controller.

  Also, is it possible to see if the graphics card is "there"? I think that if it does not show in the BIOS menu, either is missing or broken.

  Any help is appreciated.

  Thank you
  Teo

  There are two ways to create a mobile video hybrid:

  1 hardware control - with a multiplexer equipment

  2 control software, where only the GPU from Intel is hard wired to the display and the secondary GPU is used as a coprocessor.

  Your system is of type 2.  It is not a true independent GPU - this is a coprocessor for the Intel's GPU, fully controlled by software and drivers.  To use the AMD GPU, choose using the Catalyst Control Center under Windows.

  The AMD GPU can never primary rendering on this system: it's a secondary GPU by design.

• Dell Vostro 430 sometimes breaks down and does not find the hard drive in the bios

  So I have this old - ish Dell Vostro 430, intel cpu, windows 7 hard disk sata 250 GB, 4 GB of ram.

  Update BIOS to the latest version 2.4.0

  In certain exceptional circumstances, this PC sometimes crashes in windows, it is restarted, and then when he comes back it does not find the hard drive as a gift. He is not seen in the bios and does not start.

  To fix, I have to unplug the power cable, wait a few seconds, plug in, reboot the computer and it starts normally, load windows and everything.

  So far, I have tried to paginate on another hard disk, reinstall the Windows operating system from scratch, and same thing happens from time to time.

  It is difficult to find the cause of the problem, because this happens very rarely.

  Sometimes, when the pc is turned on for the first time in the morning, the hard drive is not found by the bios and we reappear at the same trick (disconnect the power cable) to take him back.

  When it crashes when using inside Windows, it seems that the reason is the computer can't find the hard drive.

  Such computer is out of warranty.

  It would be nice to just throw this computer because it is still fine for the work it has to do, + I have Windows and Office OEM license on it, as well as many other software that I have to reinstall etc.etc.

  No idea what I could troubleshoot?

  Maybe change the motherboard? How can I buy a new motherboard for an out of warranty Dell?

  While possibly keeping all the OEM licenses (Windows 7 and Office 2007).

  Desu

  .. .once in a while...

  That will make hard to resolve this situation.

  • Have you tried to replace the battery in the motherboard, if nothing else than to exclude it? CR2032, 3-volt lithium-ion, ~ $2 at discount stores. Do not forget to open the BIOS Setup and copy down all current settings first because remove battery BIOS resets the default values, which is maybe not correct for your specific system.
  • Have you tried another SATA data cable, or reinstall the existing at both ends?
  • Have you reinstall RAM and PCI card in their slots?
  • Have you used canned air to blow out the dust?
  • Maybe a power supply problem... ? If insufficient voltage, he could not start the HARD drive quite fast at startup, or quick enough after your option settings to be able to turn the HARD drive off when it is not accessed, what may cause this error message 'not found '.
  • If you use a power strip or surge protector, have you deleted and the PC connected directly to a wall jack?

  If it is a motherboard defective and you replace it with another jury of Vostro 430, you shouldn't have any problems with Windows or Office licenses. Assuming you are using Windows Dell reinstall for exact same version of Windows drive that was installed at the factory, it should not even ask the product key, if you must reinstall Windows on the HARD drive. But even if she asks, there should be a sticker somewhere on the PC with your unique product key so you can enter if the installer made the request.

  and make sure you have the Office product key too...

• Redirect URL with a slash at the end does not work

  I have a url for example www.example.com/test/ and I want to send to www.example.com/blog/test but it does not work because the url of the source is not save in the redirect url because of the slash at the end.

  Same thing.

  When you have an index.html in a folder called test then BC will lead the url/test, /test/ and /test/index.html to that, and if you have a 301 on this page redirect go somewhere elese.

• Dell Vostro 200 beeps twice at startup, does not start

  I have a Dell Vostro 200 desktop computer that has started to beep twice when turning on/off, but it does not start and nothing appears on the monitor. Can someone tell me how to fix this, please?

  rsiboise

  Two * beeps * indicate a problem of memory, first try to open the case and remove and reinstall all memory modules and see if that makes a difference, troubleshooting procedures more can be found in the Vostro 200 Mini Tower Troubleshooter HERE. NOTE from the ADMIN: Broken link has been removed from this post by Dell >

  Bev.

• Dell 926 printer will copy only /scan, does not print Vista

  Failed to get out of the mode copy or scan that he won't print

  Uninstall/reinstall the printer.

  http://support.Dell.com/support/downloads/DriversList.aspx?c=US&l=en&s=GEN&ServiceTag=&SystemID=PRN_ALL_A926&OS=WLH&OSL=en&CATID=&impid=

  Link above has 32-bit print drivers Vista for him.

  http://support.Dell.com/support/topics/global.aspx/support/my_systems_info/manuals?c=us&l=en&s=Gen& ~ CK = anavml

  A manual is available for your model of printer at the link above.

  http://support.Dell.com/support/topics/global.aspx/support/DellCare/contact_technical_support

  Dell technical support at the link above.

  http://en.community.Dell.com/support-forums/default.aspx

  Dell's Support Forums are available.

  See you soon.

  Mick Murphy - Microsoft partner

• Dell place 8, Windows 10: Panel Handwriting does not not after upgrade to build 1511

  I have a Tablet Dell place 8, I have always been satisfied.  As well as my main desktop and a laptop, I upgraded from W8.1 to Windows 10 quite successfully.  More recently, I've updated (via Windows Update) to build the 1511.

  Handrwriting Panel (which I've always used with the stylus of Dell, or simply a finger) is now available.  If I open the keyboard on the screen and tap the keyboard selector, I offer the standard keyboard, the keboard split ("inch") - then the/Tablet chart icon greyed out and inactive - and finally the full keyboard.

  This worked until the time of the upgrade to 1511 (although I can't be quite sure that the upgrade has caused the problem).

  I can't any help at all.  I tried Windows answers, but (as usual) lost several minutes in the superficial chat with what I think did an internship out of his depth, and who finally referred me to Dell.  I spent ages going round in circles trying to get into my account of community Dell and ended up having to create a new this afternoon.  In the past, I've used Usenet, but there are a few pockets of expertise staying there, but not, it seems, anyone with knowledge of W10.  Of course, I tried the usual, but all search engines take a variety of items for all versions of Windows except W10 - some search terms that I use.

  Can anyone help? Even just by identifying services are related or other facilities that I can try to turn the with?  (Well, of course I turned with, and google, the touchscreen keyboard and writing Service Panel without a bit of luck.)  Is it me, or Windows becomes less transparent, which means that when something doesn't work you are simply stuck?

  Phil, London

  Resolved, finally.  After a more cumulative update left the tablet with a stylus that could not retain its calibration, I decided to update it using the reset under settings option.  After a lot of time to download updates the handwriting Panel is back to normal, and the pen works well also.  I manually choose to download a language pack for British English - I can't tell if it was the missing step, but I have a tablet to work once again.  It will be some time until I found the time to reinstall all my applications out of store, but I can live with that. Need to study the system image options!

• Dell computer laptop starts but the screen does not light

  Hello

  I have a laptop Dell older (studio 1558) and when I used it the other day, 'static' filled monitor image and then the screen went completely black.  Now when I turn it on, it seems that the computer starts well but the screen is black.

  Get yourself an external monitor, easy solution, right? -bad.  Unfortunately when I plugged my laptop in a separate monitor, the monitor (which works fine) showed no images.

  Still, I had this laptop for a few years.  I see about being 'easy' opening and closing of the laptop.  This has been the case in recent years, however, so I don't know if something has finally given...

  I'm not the best computer savvy so sorry if I was not more detailed... any ideas, what is wrong and how do I fix?  I rather would not somewhere that make me fixed.

  You will probably get a better response if you re - post it in the forum of the laptop and mention the version of Windows, too. (This is the forum office.)