(Redirected) Real-time clock error

Similar Questions

• Satellite Pro M30 - real time clock shows wrong time

  Hello!

  most of the time I am using my Toshiba satellite pro m30 without the battery with the energy of the power system. the battery is stored somewhere outside of the computer for a month the real time clock shows a bad time if the computer is started after a period of time.

  I think my cmos battery is going to die soon.

  someone has an idea, how this cmos battery can be changed by myself?

  Thank you
  Reinhard

  Hello Reinhard

  I agree with you. It is time to replace the CMOS battery. It is not easy and the machine must be dismantled. If you are not familiar with the procedure for disassembly, it can be dangerous. A small mistake can result with damaging material.

  If you want to do it alone, you do so at your own risk. Be sure to use the right battery. Maybe you won't believe, but if you use a battery hurt it could cause battery explosion, or other damage.

  I'm not 100% sure, but the RTC battery must be placed on the left side near the touch pad. If you want to only please be very gently. The laptop parts are very sensitive.

• Dell XPS L502x 5 beeps - the real time clock failure

  Hello.

  I had a problem with my grade, first the hard drive was broken and I swapped the hard drive. Now in the new road, it was not possible to restart it. So I did a reset of the BIOS. Now, he is unable to restart and I get 5 beeps - that due to manual means 'Real Time Clock Failure'.

  What is it?? And how to solve?

  Thanks in advance

  Hi Nightyboy,

  5 beep code indicates CMOS battery failure. Try to release the static power and check whether the system works. Follow the steps below.

  Turn off the system; Remove the battery, power adapter and power cable. Press and hold the power button for 30 seconds to drain any power static excesses. In case the problem persists, you may need to replace the CMOS battery, you can refer to the operating manual using the link below to replace the CMOS battery.

  http://Dell.to/1bB9On6

  In this link if please punch in the system service tag or express service code and click on submit. This will help you access the manual page.

• Spectrum of HP x 360 not Convertible: 360 x spectrum probe real-time clock/calendar jumps

  Hello

  New HP spectrum wife x 360 has a problem with the system time real clock/calendar that keeps jumping a few days before when shee starts first to the top of the fashion watches.

  In the old days that indicate generally small battery back to the processor was "dead." Does anyone know how they keep the RTC "alive" now? Battery? Super capacitor?

  If it is via the battery does anyone know if it is easy to replace?

  Service manual available anywhere?

  Thank you

  Dave

  Now, I went 4 days with no 'Skip Date'. I updated the bios on the current Rev, and the problem is solved!

  Easy Peasy update (remember to plug it in the power before you start). A 15-minute.

  Thanks to the support, it's fixed!

• labview real-time clock display

  Hey dude, im doing a project on labview that I just want to make prettier for the speaker

  is it possible to add a clock to the façade that tell time, ideally in format:

  any help welcome

  Thank you

  Kevin

  Pretty cool Tim.  Here is an old floating around, I got that has a neat wooden face and the code is really simple.   It is in LV10.

• Time clock errors

  My new to me clock SL500 continues to change the time on the clock.  The minutes are correct, but the clock gets several hours.  I don't know if this happens just at the moment where I'm running on batteries, but the incident the more recent was after using the battery.

  Someone at - he lived a similar anomaly?  Is there a way to avoid this?

  what locale you selected in language and region under control panel, also what time zone... I think you chose something wrong, and it keeps itself updated last time regional. It does not resemble a CMOS battery drained.

• Satellite P200 - Real Time Clock battery

  When I turn on my Satellite P200-13Z, he sometimes tells me that the date and time settings are incorrect. I think it's due to RTC battery becoming discharged. Usually I run off the computer, so it should load up when I'm not with her.

  Can anyone help?

  Hi Michael

  The CMOS battery the laptop must be connected to the power adapter for about 12 to 15 hours!
  First the main battery may load and then the battery CMOS!
  This procedure takes a little more time

  Should check this out!

• Real time clock RTC accuracy test

  How do you verify the accuracy of the RTC?

  This computer is new and has been placed in use on 20/09/2015.

  Time is controlled through www.time.is

  He said that the time is always delayed if you use windows 7 Professional.

  When the time settings are changed by updating, it will very frequently show exact time.

  The CMOS RTC battery has been replaced with a new battery and has not changed.

  An external flash drive has been used to download a utility and then Ubuntu was installed on the flash drive so that Ubuntu starts after a fresh boot.

  There is no period of time with Ubuntu.  With Ubuntu, the time is coming.

  With windows 7 Professional, the time varies and moves of 0.7 seconds to 1 minute or sometimes 1 minute and 30 seconds.

  With Ubuntu, time progresses varies and moves of exact time to 0.9 seconds ahead of testing about 12 hours.

  How did the two operating systems produce different results?  The one with the period of delay and the other with the time to follow?

  What was/is the software that other messages make reference to test the accuracy of the RTC?  Was UEFI, or something else?  For this computer just to edge of diagnosis or UEFI tests have so far managed.

  How do you check the Crystal in the motherboard?

  How do you check the RTC chip in the motherboard?

  Hello

  Thanks for posting your query in Microsoft Community Forum.

  According to the description of the issue, I recommend you post your query in the TechNet Forums. TechNet is watched by other computing professionals who would be more likely to help you.

  TechNet Forum

  http://social.technet.Microsoft.com/forums/Windows/en-us/home?category=w7itpro

  Hope this information is useful.

• "1 MHz" for the name of the source on the time loop does not work on LabVIEW Real-time 9.0

  A Loopis Timed running as expected if a time source is manually chosen in the dialog box of configuration for "1 kHz" (first digit) and "1 MHz" (second digit). If the time Source name is set through the input of the channel "1 kHz", the loop is executed, too third figure). But if the input string is "1 MHz", the loop is not executed (last figure). The channel two are created by "create constant" on the entry of the loop to exclude typos. Is it possible to set the Source of a loop time timed through the input string to the real-time clock hard Mhz?

  

  

  

  

  OK, I was a bit confused by the difference between the behavior of error...

  Now, the question is quite clear. Aid for the timed loop provides the following regarding the Source of the calendar entry:

  Specifies the name of the synchronization source to use to control the structure. The source of synchronization must be created using the create synchronization Source VI on the block diagram or selected in the dialog box Configure the timed loop .

  So, I think that you have somewhere in your code a time Source.VI create if you pass "1 kHz" as the name. But you did not do this for your clock "MHz 1"...

  hope this helps,

  Norbert

• Satellite P100 - time clock keeps changing

  The clock on my Satellite P100 continues to change (running Win XP MCE) randomly during the day while it is running.

  When I start the PC in the morning, clock's time similar to when I turned off the day before.

  I use my PC in my office connected to the power supply. For the first months of ownership I left battery off the computer because I wanted to preserve his life. I don't want to run on battery and go through a process of charge-discharge throughout the day while I'm working. I was wondering if this could be the problem and now keep the main battery plugged all the time but the clock still continues to change.

  The clock doesn't change by specific hours, but at some point almost randomly sometime before the correct time. Sometimes a few minutes, sometimes hours.

  I installed and run all of the last anti-virus, spyware etc etc and nothing is detected.

  Looks like my faulty CMOS/RTC battery?

  This is my work computer and I can't afford to be without it for more than a day. I don't want to go back with all my data on HDD business.

  Someone knows how it is easy to replace the RTC battery yourself (I know it will void the warranty)-I am an experienced PC "Builder" and fortunately can disassemble computers etc.

  I hope that someone can offer some advice. Why Toshiba is not a help line that you can ask for help?

  Hello

  Maybe it's not a RTC battery problem, but the problem of BIOS?

  I found this Toshiba on a resource conflict real time clock in the L100 and P100 notebook Device Manager
  http://support.toshiba-tro.de/KB0/TSB7301SU0005R01.htm

  It is very interesting, if this resource conflict could have a bad influence on the time of windows.
  Check it!

• Get strange errors 'real time' in the browser console, what do mean?

  I noticed recently that since yesterday is the day prior to that, I get a strange 'real-time' error messages in my browser console log. I get them for more or less the same sites, and I have attached a screenshot of some of the most common mistakes for example. I see these errors very frequently in the browser console log.

  So I'm a little worried about what mean these errors, why I want to come and if anything, what to do about them.

  Hello

  Try Firefox Safe mode to see if the problem goes away. Firefox Safe mode is a troubleshooting mode that temporarily disables hardware acceleration, restores some settings and disables add-ons (extensions and themes).

  If Firefox is open, you can restart Firefox Safe mode in the Help menu:

  • Click the menu button

    

    click Help

    

    then select restart with disabled modules.

  If Firefox does not work, you can start Firefox in Mode safe as follows:

  • On Windows: Hold down the SHIFT key when you open the desktop Firefox or shortcut in the start menu.
  • On Mac: Hold the option key during the startup of Firefox.
  • On Linux: Exit Firefox, go to your Terminal and run firefox-safe-mode
    (you may need to specify the installation path of Firefox for example/usr/lib/firefox)

  When the Firefox Safe Mode window appears, select "start mode safe."

  

  If the problem is not present in Firefox Safe Mode, your problem is probably caused by an extension, theme or hardware acceleration. Please follow the steps described in the section Troubleshooting extensions, themes and problems of hardware acceleration to resolve common Firefox problems to find the cause.

  To exit safe mode of Firefox, simply close Firefox and wait a few seconds before you open Firefox for normal use again.

  When find you what is causing your problems, please let us know. This might help others with the same problem.

• Liaison GPIB CVI 2009 real-time error

  The code of source GPIB only call the ibdev function.

  ibdev (0, 1, NO_SAD, T10s, 1, 0);

  When I tried to compile the code source GPIB CVI 2009 real-time, I received the error message following link.

  Project link error:

  Symbol not defined "__imp__GetCurrentProcess@0" referenced in "c:\program NIUninstaller instruments cvi2009\cvi2009\bin\msvc\cvistart.lib '...

  But the GPIB source code can be compiled and run under windows XP.

  Any help out there?

  Thank you.

  Vincent,

  Hello.  First of all, I wanted to mention that the NI GPIB library is not officially supported on systems time real LabWindows/CVI.  Your customers use it more in the earlier applications of CVI RT?  Can you tell me what features they use?

  While the NI GPIB library is not officially supported in CVI RT, errors of link that you see in CVI 2009 were not intentional.  You can tell your customer to copy the file gpib.lib to the location of the CVI 9.0:

  \National Instruments\\bin\msvc\gpib.lib

  the location of CVI 2009:

  \National Instruments\\bin\msvc\gpib.lib

  This should fix the problem.

  If your client has never repair or reinstall their installation of CVI 2009, they will have to make this change again.

  We intend to fix this in the next version of LabWindows/CVI.

  -Jeff

  NEITHER

• Error-307650 during a sequence in real-time with API LV

  I created a basic real-time sequence that checks the time it takes a signal reach a certain threshold.

  

  On the side of the LV, I use the API to call this sequence. I make sure that all channels and settings are defined as in the examples. However I get 307650 error that says "NEITHER VeriStand: Index was out of range." Must be non-negative and less than the size of the collection.

  ' Parameter name: index.

  Any suggestion to help here? THX. Code is attached.

  There are two problems here:

  1. The Stimulus profile editor is not indicating that there is an error with this sequence, although there is a. Note that the variable InitialTime is used in an expression, but is not declared as a parameter or a local variable.

  2. you get an error at runtime because of it, but it's not terribly useful (index out of range).

  You can fix this by adding a local variable of InitialTime to your sequence. I dropped the CAR 338386 about this bug.

  Once you do this, there is something extra, you will need to set in your VI which runs the sequence so he could get the results of the sequence properly. You use correctly the value of the sequence name to read the back of the sequence Variable. You use the Session name used during the deployment of the sequence. Which does not match the name sequence.

  To get the name of the sequence, use VI to get all the names sequence on your session profile of stimulus to get the array of names for all of the top level of the session sequences, then index on the first point, given that you only use a single sequence. Example below:

  

• FPGA FIFO real-time error-61206

  I used this white paper as a base for my code. My FPGA look like:

  

  And my time real-time (RT):

  

  I am using a cRIO-9022 and now just trying to get the foundations buried for my project. The problem is that the side FPGA works well but environmental RT takes maybe 2 or 3 seconds and close with this error:

  Code:-61206

  Source: Read/write in FIFO_pressure_RT.vi control

  I have not dealt with the FIFOs in LabView before I have no idea what is the cause. Any ideas?

  Thank you

  Logan

  What version of LabVIEW are you using? In LabVIEW 2011, if orders or the lights on the front of the FPGA had a jump of line or transport back in the label, the question would be filling in the read/write control node, but you would see this error. It seems that Input Data (synchronous display) probably has a newline character that could cause this. That the problem has been solved in LabVIEW 2011 SP1, but what happens if you remove the line break and recompile the FPGA VI?

• Error trying to create the exe for real-time target

  I have a target program that works well on target in real time, but hangs when I try to create an executable fron, error is:

  An error occurred during the recording of the following file:

  C:\Program NIUninstaller Instruments\LabVIEW 2009\vi.lib\Motion\FunctionBlocks\straightLineMove\nimc.fb.straightLineMove.startStraightLineMove.axis.modeVelocity.0.vi

  Invoke the node in AB_Source_VI.lvclass:Close_Reference.vi-> AB_Build.lvclass:Copy_Files.vi-> AB_Application.lvclass:Copy_Files.vi-> AB_RTEXE.lvclass:Copy_Files.vi-> AB_Build.lvclass:Build.vi-> AB_Application.lvclass:Build.vi-> AB_RTEXE.lvclass:Build.vi-> AB_Build.lvclass:Build_from_Wizard.vi-> AB_UI_Frmwk_Build.lvclass:Build.vi-> AB_UI_FRAMEWORK.vi-> AB_CreateNewWizard_Invoke_CORE.vi-> RTBUIP_CreateNewWizard_Invoke.vi-> RTBUIP_CreateNewWizard_Invoke.vi.ProxyCaller
  
  Method name: Save target: Instrument

  Visit ni.com/ask support request page to learn more about the resolution of this problem. Use the following as a reference:

  Error 6a held at AB_Source_VI.lvclass:Close_Reference.vi-> AB_Build.lvclass:Copy_Files.vi-> AB_Application.lvclass:Copy_Files.vi-> AB_RTEXE.lvclass:Copy_Files.vi-> AB_Build.lvclass:Build.vi-> AB_Application.lvclass:Build.vi-> AB_RTEXE.lvclass:Build.vi-> AB_Build.lvclass:Build_from_Wizard.vi-> AB_UI_Frmwk_Build.lvclass:Build.vi-> AB_UI_FRAMEWORK.vi-> AB_CreateNewWizard_Invoke_CORE.vi-> RTBUIP_CreateNewWizard_Invoke.vi-> RTBUIP_CreateNewWizard_Invoke.vi.ProxyCaller

  Possible reasons:

  LabVIEW: File generic i/o error.
  =========================
  NOR-488: IO abandoned operation.

  The second was the issue, I found myself actually apply to open with an engineer and he helped me. Thank you very much!