Reference Dell 6248P - Port fiber

Similar Questions

• Reference Dell 6248P - Guest Wifi VLAN config

  I am trying to retrieve all upward of a VLAN. The VLAN is comments wireless traffic going through our main switches and on an ADSL router but I'm running into some difficulties.

  We have 3 points of access for model AP - AC Unifi. Each access point has a connection of physical network of 1 of 4 Dell 6248 switches which are currently in a single stack managed as follows.

  AP 1-> Port of the Switch 1 40

  AP 2-> Port of the Switch 2 36

  AP 3-> Port of the Switch 3 17

  The managed pile and AP are currently using the 192.168.1.0/24 on VLAN 1 - default and I created a VLAN 10 - guest.

  The APs have two SSID WLAN, 'corporate', which is also on the 192.168.1.0/24 range and 'guest' that is located on 192.168.99.0/24. I put the "guest" to mark its traffic with VLAN 10 and no DHCP is defined.

  I put the 3 above general Mode ports, allowing all managers and VLAN - 1 that are not marked and VLAN - 10 they are labeled.

  I also put a Zyxell router with a static address of 192.168.99.254 in Switch 4 Port 24 and set the access mode for VLAN 10.

  The router is configured to provide DHCP for the beach of 192.168.99.0/24.

  Now when I connect a laptop to our 'coporate' WLAN, everything works fine. I get a DHCP address from our server and I can reach everything as usual.

  When I connect to the "guest" WLAN, I do not receive a DHCP address, in addition, I am able to ping on subnet 1 hardware VLAN I thought would not be possible.

  Can someone take a look at this config and I would like to know what is the problem with him?

  ! Current configuration:
  ! Description of the system «PowerConnect 6248P, 3.3.12.1, VxWorks 6.5»
  ! 3.3.12.1 system software version
  ! Passage mode is configured as disabled
  !
  Configure
  database of VLAN
  VLAN 10
  VLAN 10 1 routing
  subnet of VLAN association 192.168.99.0 255.255.255.0 10
  output
  unicast SNTP client enable
  192.168.1.18 SNTP server
  battery
  1 5 Member
  2 5 Member
  3-5 Member
  4-5 Member
  output
  switch priority 1 12
  IP 192.168.1.212 255.255.255.0
  default IP gateway - 192.168.1.227
  IP - my.domain domain name
  name of the IP-server 192.168.1.18
  name of the IP-server 192.168.1.19
  name of the IP-server 192.168.140.2
  IP routing
  IP route 192.168.99.0 255.255.255.0 192.168.99.254
  interface vlan 10
  name of the "Guest".
  Routing
  IP 192.168.99.212 255.255.255.0
  bandwidth 10000
  IP helper-address 192.168.99.254 dhcp
  IP mtu 1500
  output
  level of a8e64cdc85228f4c837da747958ffd74 user name 'admin' password encrypted 15
  l2relay DHCP
  DHCP l2relay vlan 2.10
  !
  interface ethernet 1/g7
  Auto mode channel-group 2
  output
  !
  interface ethernet 1/g8
  Auto mode channel-group 1
  output
  !
  interface ethernet 1/g40
  switchport mode general
  switchport general allowed vlan add 10 tag
  output
  !
  interface ethernet 2/g36
  switchport mode general
  switchport general allowed vlan add 10 tag
  output
  !
  interface ethernet 3/g2
  Auto mode channel-group 2
  output
  !
  interface ethernet 3/g17
  switchport mode general
  switchport general allowed vlan add 10 tag
  output
  !
  interface ethernet 3/g48
  Auto mode channel-group 1
  output
  !
  interface ethernet 4/g24
  switchport access vlan 10
  output
  output

  I was looking back through the configuration, and on the 24 port setting, I see there is a command to access in place, but the port is not set to enter the mode. Can you try to put the port in access mode?

  interface ethernet 4/g24
  switchport mode access

  During the test with the laptop plugged on the switch, we should test it first with a static IP address. This is to ensure that we have a connection established. Then you can move on to DHCP.

  The router will appear in the output of one of these two commands?

  console switch arp #show

  #show bridge console table address

• Reference Dell 6248P - VLANS, DHCP, wireless AP

  Hello

  I'm trying to set up a VIRTUAL LAN for wireless comments traffic go through our main switches and on an ADSL router but I'm running into some difficulties.

  We have 3 points of access for model AP - AC Unifi. Each access point has a connection of physical network of 1 of 4 Dell 6248 switches which are currently in a single stack managed as follows.

  AP 1-> Port of the Switch 1 40

  AP 2-> Port of the Switch 2 36

  AP 3-> Port of the Switch 3 17

  The managed pile and AP are currently using the 192.168.1.0/24 on VLAN 1 - default and I created a VLAN 10 - guest.

  The APs have two SSID WLAN, 'corporate', which is also on the 192.168.1.0/24 range and 'guest' that is located on 192.168.99.0/24. I put the "guest" to mark its traffic with VLAN 10 and no DHCP is defined.

  I put the 3 above general Mode ports, allowing all managers and VLAN - 1 that are not marked and VLAN - 10 they are labeled.

  I also put a Zyxell router with a static address of 192.168.99.254 in Switch 4 Port 24 and set to this mode of trunk to VLAN 10.

  The router is configured to provide DHCP for the beach of 192.168.99.0/24.

  Now when I connect a laptop to our 'coporate' WLAN, everything works fine. I get a DHCP address from our server and I can reach everything as usual.

  When I connect to the "guest" WLAN, I don't get a DHCP address. If I put a static address, I can't do a ping to the router.

  Could someone tell me if my configuration is correct?

  Thanks for the additional information and the display to the top of the config.

  A couple of things I noticed the config:

  -I don't see that whatever it is set to Switch 4 Port 24, which is the case the router Zyxell is plugged. If this port is not configured properly, it may not be able to see the communication on the VIRTUAL LAN. A config like this should work on Switch 4 Port 24.

  # interface ethernet 4/g24

  switchport mode access #.

  # switchport VLAN 10 acccess

  -You may need to configure a static route to highlight traffic VLAN to the router.

  # ip route 192.168.99.0 255.255.255.0 192.168.99.254

  I would like to know if any of this helps.

• Cannot print. Reference Dell 944 communication usb port is not available. error check your firewall settings to ensure the printer communication is not blocked.

  Original title: unable to print. Reference Dell 944 communication usb port is not available.

  Message says 'check your firewall settings to ensure the printer communication is not blocked. Printer has worked faithfully until the problems started with the XP Home operating system. To cut a long story short ram upgraded to 2 GB, all unnecessary programs identified and technician Microsoft contacted to solve problems.  I was informed of problems caused by 3rd software party conflicts. Kaspersky was apparently the culpit. Dell Inspiron 32 now much faster but the printer will not work little matter what I do. I tried to reload with drivers & utility CD, drivers uninstalled & reinstalled on the site of all nothing is? Can someone help?

  DavidNicholsonXN,

  How to download and install drivers in the correct order

  also try to read...

  The owners of all-in-one printer Dell 944 thread (W7)

  Let the printer after Kaspersky

  Rick

• Reference Dell M1000e + aggregator MI/O port mapping

  Hi all

  I intend to install a new chassis Dell M1000e with Dell M/o aggregator. During the time of solution, I have a few questions about correspondences between the physical uplink with NDC blade ports ports. A Please check the config below and specify my queries?

  My hardware:

  • 1 x Dell M1000e
  • 2 x M i/o aggregator (A1 & A2)
  • 16 x M630 Blade (Qlogic 57840 S ANC four ports card)

  Reference DELL M/o aggregator:

  (reserved for Future use) module QSFP + 2 ports (Port No1:33 - 36 & No2:37 Port-40)

  I want to use these two modules for my blades 4-port Quad and the confusion I had, how to associate these 16 ports (8 ports of each module) to the server blade and the amount of bandwidth I will get by blade with redundancy.

  Module 4-port SFP + 10 GbE (Flexi-O of the Bay) (Port No.: 41-48)

  Module 4-port 2/4/8 Gb FC FlexIO (Flexi Bay 1) (Port No.: 49-56)

  FYI - I would like to install ESXi 6.0 on all blades

  Thank you!!

  Vinay

  Oriented server ports are configured automatically as part of the aggregation of links groups if the server is configured for the LACP Protocol. Static GAL is not supported.

  You will use the segregation network VLAN. A VLAN for network traffic and the other for the CF. Here are the commands to configure interfaces for different VLANS.

  Unidentified:

  Dell (conf) # tengigabit interface 0/16

  Dell(conf-if-te-0/16) # vlan unidentified 4

  Output Dell(conf-if-te-0/16) #.

  Tag:

  Dell (conf) # tengigabit interface 0/16

  The tag vlan Dell(conf-if-te-0/16) # 4

  Output Dell(conf-if-te-0/16) #.

  Traffic from servers will follow the path of the VLAN. For example, if an internal server, facing the port is set to VLAN 4, that traffic will be transmitted on the uplink port which has also set to VLAN 4.

  By default, all external ports are placed in a single whole LAG. However, you can change the configuration to support several shifts of uplink. Page 159 of guys configuration takes you step by step on setting up several shifts of uplink.

  The aggregator automatically configures to match the FCoE parameters used in the switches to which it connects through its uplink ports. FIP snooping is automatically configured on an aggregator. Automatically configured port channel (LAG 128) works CWF port mode. See page 86 for more information and examples of config.

  For redundancy, you could stack the units together. 241 page details the process of stacking.

  Page 54 of 102 of the Guide blade IO has one other diagram that details more internal server port mapping for each blade.

• Reference Dell 6224 and 5448

  Hi team,

  I'm new dell switches - exposed to cisco switches. I am faced with new kinds of problems with these dell switches. Unable to provide a fix and fight for the last 5 days. Pls help me. Below is my script

  Two nw - 2.0 and 3.0 is required to be configured in VLAN, VLAN ID 2 and 3.

  VLAN 2 - 192.168.2.1

  VLAN 3 - 192.168.3.1

  N/W 2.0 and 3.0 N/W machinery will be shared 48-Port powerconnect switch 5448 DELL

  The routing part arrives at 6224 power connect - gateway for vlan 2 - 192.168.2.1 and bridge for VLANs 3 - 192.168.3.1

  The switch of two is ascending through fiber optic - spf port cable

  This is the configuration I did-

  5448 switch-

  database of VLAN

  VLAN 2, 3

  output

  interface vlan 2

  switchport access vlan 2

  GVRP enable

  Routing

  output

  interface vlan 3

  switchport access vlan 3

  GVRP enable

  Routing

  output

  interface ethernet 1/you/1

  switchport mode general

  VLAN allowed switchport General add 2.3

  GVRP enable

  output

  interface ethernet 1/g1

  switchport access vlan 2

  GVRP enable

  output

  interface ethernet 1/g2

  switchport access vlan 3

  GVRP enable

  output

  Uplink port is TE1 (Layer 2) to XG2 (Layer 3)

  Reference Dell 6224 can connect

  Configure the terminal

  interface vlan 2

  no downtime

  IP 192.168.2.1 255.255.255.0

  Routing

  output

  interface vlan 3

  no downtime

  address 192.168.3.1 IP 255.255.255.0

  Routing

  output

  interface ethernet 1/xg2

  switchport mode general

  VLAN allowed switchport General add 2.3

  GVRP enable

  Computer with 192.168.2.100 / 24 GW 192.168.2.1 connected to layer 2 switch g1 - vlan 2

  When I ping 192.168.2.1 - accessible United Nations host destination

  Even the wise

  Computer with 192.168.3.100 / 24 GW 192.168.3.1 connected to layer 2 switch g1 - vlan 3

  When I ping 192.168.3.1 - accessible United Nations host destination

  Any thing that has missed out in the configuration part / all bad entries. I'm not sure now how to treat this. Pls help me and it is an urgent task for me

  Thank you

  With multiple VLANs, you need to use the general/Trunk mode. With the help of the info we have I made a diagram to help show the location of the switches and parameters on them. Obviously things can be different, such as PVID, IP address, VLAN ID etc are all customizable to your needs. But the page layout modes and the port will remain the same.

  

  STP will not fill the VLAN on the other switches. It's probably the GVRP feature it refers. With such a short race, it is more practical to manually add the VLAN. At least for the initial Setup, then once everything works enable GVRP to accommodate future expansion of VLAN.

  Hope this helps some.

• Connect sonicwall tz215 with dell 6248P

  I'm currently setting up the 6248P powerconnect switch switch with sonicwall router tz215. I'm doing the transition as simple as possible. The router will make the WAN and DHCP and the switch will route traffic between subnet PCs and WAN of sonicwall for internet access.

  I have the selector on default and vlan1 as management vlan. should I start to create the vlan 10 for IP subnet, which is the same as sonicwall LAN subnet?

  SonicWALL x 0: WAN (fibre); x 1: WAN (ADSL2 +); x 2 LAN (10.0.0.x)

  Dell 6248P 44 port: connection with sonicwall x 2

  Please recommend any config step by step, thank you very much.

  6200 switches are not able to deliver their own management of VLANS. When you configure routing VLAN you will need to follow this article.

  http://Dell.to/1FiQhu7

  It is common to see only one VLAN dedicated to the connection between the switch and the firewall. So in this example VLAN 10 would give an IP address in the same subnet as the firewall. Then place the port access mode for VLAN 10 44.

  The 6248 you'll also want to place a static route that directs traffic on the firewall. Looks something like this:

  # ip route 0.0.0.0 0.0.0.0 192.168.10.1

  Address of the firewall. The SonicWall also have some static routes in routing traffic to the internal network.

  http://Dell.to/1SdpdUh

  The getting started guide is a good starting point for the configuration at the start of the switch. Then use the user's guide for instructions on configuring additional features.

  http://Dell.to/1EJ4qlK

  If you are in need of more support deepened with the SonicWall, it may be best to contact SonicWall support group.

  http://Dell.to/1VZtZ70

  Let us know if run into snags or have any questions.

• Reference Dell MD3200i correct editing with IP system and the NIC for faster network speeds

  Hi all

  I worked on this project for a while now. I did a lot of research and have contacted Dell several times. I need help.

  I have 2 sets of identical to use for Hyper-V clusters servers. We bought a Dell MD3200i in November, we also bought a Dell 5424 switch and a Cisco SLM2048 switch. These servers have Real Tek 2 network cards for iSCSI Jumbo frames is 9 k

  The Dell MD3200i is two SAN controllers. Dell 5424 is the iSCSI optimized switch and Cisco is a 48 switch ports. iSCSI is on its own network that nothing else is connected to it. (There is an Iomega NAS and a promise Vtrak SAN Tech with all current domain of execution with iSCSI controller)

  Reference Dell MD3200i controller 0 Port 0 192.168.130.101 controller 1 Port 0 192.168.131.101

  Controller controller Port 1 0 192.168.130.102 1 1 192.168.131.102

  Controller controller Port 2 0 192.168.130.103 1 2 192.168.131.103

  Controller controller Port 3 0 192.168.130.103 1-3 192.168.131.104

  Cisco switch has 1 VLAN n ° 1 on it and the 130 subnet inside elements. There are 8 connections to the switch. 4 controller 0 and 1 of each of the servers. It has an IP of 192.168.132.4, but that switch IP does not make difference. Lighted Jumbo frames

  Dell switch has 2 of #1 for various things such as the domain controller, Vtrack, and SIN. Subnet 2 is 131 and has a total of 8 connectors inside. 4 in 1 controller and 1 from each of the servers. Lighted Jumbo frames. The switch IP address is 192.168.132.2

  Groups of servers. Each server node running Windows 2008 R2 SP1 and running hyper-v with virtual server clusters / storage folder on them. 2 Realtek NIC with Jumbo frames made 9 k ProdNode1 and ProdNode2 have 12 Core i7 CPU with 12 GB memory, EXNode1 and ExNode2 have 12 Core i7 CPU with 24 GB of memory.

  ProdNode1 iSCSI-1 192.168.130.110 ProdNode1 iSCSI-2 192.168.131.110

  ProdNode2 iSCSI-1 192.168.130.120 ProdNode2 iSCSI-2 192.168.131.120

  ExNode1 iSCSI-1 192.168.130.130 ExNode1 iSCSI-2 192.168.131.130

  ExNode2 iSCSI-1 192.168.130.140 ExNode2 iSCSI-2 192.168.131.140

  Portal discovery iSCSI on ProdNode1 went to 192.168.130.110 192.168.130.101 and 192.168.131.110 192.168.131.101 each of the other servers Discovery Portal have been pairs like this.

  iSCSI tab click on add 8 MPIO sessions at each of the ports on the MD3200i from Dell, target. For example, I added 1 session of 192.168.130.101 using it. Add Session,--> activate--> Advanced Mutlipath--> Local--> IP 192.168.130.110 initiator and target 192.168.131.101 iSCSI adapter. This is repeated on all servers. 4 connections for each NIC.

  The network is very slow. It revolved around 2 to 4 MB/MIN and it should be much faster. Initially, we had only the Cisco switch with only 1 VLAN and everything connected directly to it. I read somewhere that MPIO has been the problem, so I went through the same configuration but does not verify the MPIO checkbox above. Once this has been done, the network speed went up to 1.5 GB/Min but modular storage Dell was not happy, and virtual servers would fail and the connection is not very stable.

  What wrong with my setup? Can I directly home and fix the servers directly to the PowerVault and will make stable and allow for failover and redundancy NIC? I need to get this stable so I can move with something else.

  Thank you Ron

  You will need to change your system of intellectual property on this:

  rbramble

  EX-Node1 iSCSI-1 192.168.130.130

  EX-Node1 iSCSI-2 192.168.131.130

  EX-Node2 iSCSI-1 192.168.132.140

  EX-Node2 iSCSI-2 192.168.133.140

  Prod-Node1 iSCSI-1 192.168.130.10

  Prod-Node1 iSCSI-2 192.168.131.10

  Prod-Node2 iSCSI-1 192.168.132.20

  Prod-Node2 iSCSI-2 192.168.133.20

  Reference Dell MD3200i

  Controller 0 Port 0 - 192.168.130.101 Jumbo Frames 9K

  Controller 0 Port 1 - 192.168.131.101 Jumbo Frames 9K

  Controller 0 Port 2 - 192.168.132.101 Jumbo Frames 9K

  Controller 0 Port 3 - 192.168.133.101 Jumbo Frames 9K

  Controller 1 Port 0 - 192.168.130.102 Jumbo Frames 9K

  Controller Port 1 1 - 192.168.131.102 Jumbo Frames 9K

  Controller 1 Port 2 - 192.168.132.102 Jumbo Frames 9K

  Controller 1 Port 3 - 192.168.133.102 Jumbo Frames 9K

  Your iSCSI sessions will be:

  For EX-Node1:

  -192.168.130.130 to 192.168.130.101

  -192.168.130.130 to 192.168.130.102

  -192.168.131.130 to 192.168.131.101

  -192.168.131.130 to 192.168.131.102

  For EX-Node2:

  -192.168.132.140 to 192.168.132.101

  -192.168.132.140 to 192.168.132.102

  -192.168.133.140 to 192.168.133.101

  -192.168.133.140 to 192.168.133.102

  For Prod-Node1:

  -192.168.130.10 to 192.168.130.101

  -192.168.130.10 to 192.168.130.102

  -192.168.131.10 to 192.168.131.101

  -192.168.131.10 to 192.168.131.102

  For Prod-Node2:

  -192.168.132.20 to 192.168.132.101

  -192.168.132.20 to 192.168.132.102

  -192.168.133.20 to 192.168.133.101

  -192.168.133.20 to 192.168.133.102

• Reference Dell 1700 crashed and I have no backup

  Reference Dell 1700 crashed without backup whats a girl to do
  
  

  lost all programs can run does not help

  Reference Dell 1700 crashed without backup whats a girl to do

  
  

  lost all programs can run does not help

  Reinstall Wndows.

  Reinstall all your programs from the original media or downloaded files you have saved on an external drive.

  Reinstall all your data from the backups that you made on an external drive.

  If you have not, you're out of luck.

• Reference Dell vostro 1520 with windows xp prof... Not reading CD/DVD

  Reference Dell vostro 1520 with windows xp prof... Unable to read & play any cd/dvd.tried mr.fixit content but no solution at the moment.

  Hello

  1 have. what fixit you tried?
  2. don't you make changes to the computer before the show?

  Your CD or DVD drive is missing or is not recognized by Windows or other programs
  http://support.Microsoft.com/kb/982116

  Important: To do: Important This section, method, or task contains steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click on the number below to view the article in the Microsoft Knowledge Base: 322756 (http://support.microsoft.com/kb/322756/) how to back up and restore the registry in the window.

• Reference Dell pc with xp family. Restart to the logon screen

  Reference Dell pc with xp family. Restart to the logon screen. starts ok in safe mode. run msconfig and do that no change then do restart ok everything ok until the cold start, then hand it to restart?

  Peek into the registry to find clues.

  Disable the automatic restart in case of system error and see if you can capture a message of error checking bug (BSOD) with useful information.  Automatic restart in the event of system failure can be disabled in the F8 advanced boot menu, or you can turn it off in system properties.

  1. right click on my computer and select Properties.
  2 - Click on the Advanced tab, and then click on the Start button and recovery settings.
  3 clear the automatically restart box and OK your way out system properties.

  Start the computer in a Clean Boot State, if the computer starts successfully in a clean boot state, then one of your user programs most likely problems, look in the case of journal of indexes.

  How to configure Windows XP to start in a "clean boot" State
  John

• Reference DELL T420 - battery on PERC H710 adapter controller

  Hello

  I received a yellow warning

  Reference DELL T420 'Battery on PERC H710 adapter controller'

  What it means?

  What should I do?

  Order the new battery?

  It is a simple replacement mission?

  Is it essential?

  Update:

  test URL

  http://www.Dell.com/support/article/us/en/04/SLN130018

  Have nothing, everything seems fine now...

  Thank you

  It is normal so he can make a full discharge of the battery as part of his learning cycle every 90 days. Make sure that this isn't that. If this isn't the case, the reason, give it 24 hours. If it is fully charged, update the system (including RAID firmware, driver first) firmware. If not fully charged yet or it reproduces quickly, then replace the battery - power down to replace.

• Reference Dell 3110cn of Laserjet + os El Capitan

  My MacBook Pro (2009) stopped my Dell printer. News on this please.

  Hi deaconjo,

  as I had the same problem, I found a solution for my El Capitan MacPro 2008:

  Search for the following installation program:

  3130cn_Installer_And_Application_Dell_A04_MAC.dmg

  Inside this package you will find the driver for 10.7 and higher. After installing the package I could add an IP printer with this driver:

  Reference Dell 3130cn Color Laser v3017.104 PS

  With this driver installed, I can use my printer Dell 3110cn without problem.

  Perhaps it might help you too.

  Concerning

• Reference Dell Sonicwall SRA

  Hey guys, more of a statement than a question. If you have a Dell Sonicwall and users do "found no appropriate group" of course the same user does not exist as a local user and a domain user. This will cause problems. Took me a while to understand that >.<>

  Good thought.

  Thank you
  Ben D
  Reference Dell SonicWall
  #Iwork4dell

• Reference Dell 2007FP vs HP zr22w

  Hi guys, I use t410s now. You want to find an IPS monitor. Currently have two choices.

  Reference Dell 2007FP (handed to nine 30-day warranty) $95

  HP zr22w (new, 3-year warranty) $175

  What would be a good choice?

  Not for the game.

  But need good color, good text, Word process, sometimes a movie.

  The HP zr22w DP, is better than the VGA to connect to my T410s?

  

  Thank you!

  Your information is so helpful. But I think that I can not check the number helpfully I ordered from DELL FINANCIAL SERVICES. Thank you very much!