Reference Dell 6248P - VLANS, DHCP, wireless AP

Similar Questions

• Reference Dell 6248P - Port fiber

  Hello

  I am trying to connect to port 1/xg1 (fiber Slot) on my Dell 6248P switch SFP 1 G and it's not working.

  Is that the port takes in charge only 10G?

  Thank you.

  Hello

  1/xg1 ports are 10G only. The front ports support SFP 1 G. The front ports are ports combo for 45-48 in order to use copper or fiber port, but not both.

• Reference Dell 6248P - Guest Wifi VLAN config

  I am trying to retrieve all upward of a VLAN. The VLAN is comments wireless traffic going through our main switches and on an ADSL router but I'm running into some difficulties.

  We have 3 points of access for model AP - AC Unifi. Each access point has a connection of physical network of 1 of 4 Dell 6248 switches which are currently in a single stack managed as follows.

  AP 1-> Port of the Switch 1 40

  AP 2-> Port of the Switch 2 36

  AP 3-> Port of the Switch 3 17

  The managed pile and AP are currently using the 192.168.1.0/24 on VLAN 1 - default and I created a VLAN 10 - guest.

  The APs have two SSID WLAN, 'corporate', which is also on the 192.168.1.0/24 range and 'guest' that is located on 192.168.99.0/24. I put the "guest" to mark its traffic with VLAN 10 and no DHCP is defined.

  I put the 3 above general Mode ports, allowing all managers and VLAN - 1 that are not marked and VLAN - 10 they are labeled.

  I also put a Zyxell router with a static address of 192.168.99.254 in Switch 4 Port 24 and set the access mode for VLAN 10.

  The router is configured to provide DHCP for the beach of 192.168.99.0/24.

  Now when I connect a laptop to our 'coporate' WLAN, everything works fine. I get a DHCP address from our server and I can reach everything as usual.

  When I connect to the "guest" WLAN, I do not receive a DHCP address, in addition, I am able to ping on subnet 1 hardware VLAN I thought would not be possible.

  Can someone take a look at this config and I would like to know what is the problem with him?

  ! Current configuration:
  ! Description of the system «PowerConnect 6248P, 3.3.12.1, VxWorks 6.5»
  ! 3.3.12.1 system software version
  ! Passage mode is configured as disabled
  !
  Configure
  database of VLAN
  VLAN 10
  VLAN 10 1 routing
  subnet of VLAN association 192.168.99.0 255.255.255.0 10
  output
  unicast SNTP client enable
  192.168.1.18 SNTP server
  battery
  1 5 Member
  2 5 Member
  3-5 Member
  4-5 Member
  output
  switch priority 1 12
  IP 192.168.1.212 255.255.255.0
  default IP gateway - 192.168.1.227
  IP - my.domain domain name
  name of the IP-server 192.168.1.18
  name of the IP-server 192.168.1.19
  name of the IP-server 192.168.140.2
  IP routing
  IP route 192.168.99.0 255.255.255.0 192.168.99.254
  interface vlan 10
  name of the "Guest".
  Routing
  IP 192.168.99.212 255.255.255.0
  bandwidth 10000
  IP helper-address 192.168.99.254 dhcp
  IP mtu 1500
  output
  level of a8e64cdc85228f4c837da747958ffd74 user name 'admin' password encrypted 15
  l2relay DHCP
  DHCP l2relay vlan 2.10
  !
  interface ethernet 1/g7
  Auto mode channel-group 2
  output
  !
  interface ethernet 1/g8
  Auto mode channel-group 1
  output
  !
  interface ethernet 1/g40
  switchport mode general
  switchport general allowed vlan add 10 tag
  output
  !
  interface ethernet 2/g36
  switchport mode general
  switchport general allowed vlan add 10 tag
  output
  !
  interface ethernet 3/g2
  Auto mode channel-group 2
  output
  !
  interface ethernet 3/g17
  switchport mode general
  switchport general allowed vlan add 10 tag
  output
  !
  interface ethernet 3/g48
  Auto mode channel-group 1
  output
  !
  interface ethernet 4/g24
  switchport access vlan 10
  output
  output

  I was looking back through the configuration, and on the 24 port setting, I see there is a command to access in place, but the port is not set to enter the mode. Can you try to put the port in access mode?

  interface ethernet 4/g24
  switchport mode access

  During the test with the laptop plugged on the switch, we should test it first with a static IP address. This is to ensure that we have a connection established. Then you can move on to DHCP.

  The router will appear in the output of one of these two commands?

  console switch arp #show

  #show bridge console table address

• Reference Dell 5548P VLAN

  Just connect a 5548p to our network and I can get on the web interface, I have created several VLANS and put them all access to, I have a (48) port on the vlan 1 as trunk, don't know why, but when I connect a device to one of the ports vlan, I have no access to it, I cannot ping or whatever it is , I read somewhere on another forum I need of vlan routing active but for the life of me I can't find anywhere to enable VLAN routing, or maybe it's another issue that is causing the problem? I also did the switchport mode access for all the VLANS and the trunk allowed vlan add command for all the VLANS.

  Is the connection of your 3448 to your router set as a Trunk port? The router has the same VLAN on it as well as addresses IP attributed to them?

  For example the router will have 160 VLAN on it with an IP address of 10.21.162.1

  Set the printer to 10.21.162.86 with a gateway of 10.21.162.1.

• Connect sonicwall tz215 with dell 6248P

  I'm currently setting up the 6248P powerconnect switch switch with sonicwall router tz215. I'm doing the transition as simple as possible. The router will make the WAN and DHCP and the switch will route traffic between subnet PCs and WAN of sonicwall for internet access.

  I have the selector on default and vlan1 as management vlan. should I start to create the vlan 10 for IP subnet, which is the same as sonicwall LAN subnet?

  SonicWALL x 0: WAN (fibre); x 1: WAN (ADSL2 +); x 2 LAN (10.0.0.x)

  Dell 6248P 44 port: connection with sonicwall x 2

  Please recommend any config step by step, thank you very much.

  6200 switches are not able to deliver their own management of VLANS. When you configure routing VLAN you will need to follow this article.

  http://Dell.to/1FiQhu7

  It is common to see only one VLAN dedicated to the connection between the switch and the firewall. So in this example VLAN 10 would give an IP address in the same subnet as the firewall. Then place the port access mode for VLAN 10 44.

  The 6248 you'll also want to place a static route that directs traffic on the firewall. Looks something like this:

  # ip route 0.0.0.0 0.0.0.0 192.168.10.1

  Address of the firewall. The SonicWall also have some static routes in routing traffic to the internal network.

  http://Dell.to/1SdpdUh

  The getting started guide is a good starting point for the configuration at the start of the switch. Then use the user's guide for instructions on configuring additional features.

  http://Dell.to/1EJ4qlK

  If you are in need of more support deepened with the SonicWall, it may be best to contact SonicWall support group.

  http://Dell.to/1VZtZ70

  Let us know if run into snags or have any questions.

• How can I get the driver for a Dell Latitude D800 XP wireless?

  I have a Dell Latitude D800 that I just did a clean install of XP SP3 to and the Wireless does not work. How can I get the driver for the card wireless to the computer?

  Download drivers

  Visit the manufacturer's Web site and select your model (this is usually done in the Support section). You should be able to download drivers for your model if they have drivers for your version of Windows. Download the driver and then follow the instructions to install.

  Reference Dell Driver Downloads:

  http://www.Dell.com/support/drivers

• Reference Dell M1000e + aggregator MI/O port mapping

  Hi all

  I intend to install a new chassis Dell M1000e with Dell M/o aggregator. During the time of solution, I have a few questions about correspondences between the physical uplink with NDC blade ports ports. A Please check the config below and specify my queries?

  My hardware:

  • 1 x Dell M1000e
  • 2 x M i/o aggregator (A1 & A2)
  • 16 x M630 Blade (Qlogic 57840 S ANC four ports card)

  Reference DELL M/o aggregator:

  (reserved for Future use) module QSFP + 2 ports (Port No1:33 - 36 & No2:37 Port-40)

  I want to use these two modules for my blades 4-port Quad and the confusion I had, how to associate these 16 ports (8 ports of each module) to the server blade and the amount of bandwidth I will get by blade with redundancy.

  Module 4-port SFP + 10 GbE (Flexi-O of the Bay) (Port No.: 41-48)

  Module 4-port 2/4/8 Gb FC FlexIO (Flexi Bay 1) (Port No.: 49-56)

  FYI - I would like to install ESXi 6.0 on all blades

  Thank you!!

  Vinay

  Oriented server ports are configured automatically as part of the aggregation of links groups if the server is configured for the LACP Protocol. Static GAL is not supported.

  You will use the segregation network VLAN. A VLAN for network traffic and the other for the CF. Here are the commands to configure interfaces for different VLANS.

  Unidentified:

  Dell (conf) # tengigabit interface 0/16

  Dell(conf-if-te-0/16) # vlan unidentified 4

  Output Dell(conf-if-te-0/16) #.

  Tag:

  Dell (conf) # tengigabit interface 0/16

  The tag vlan Dell(conf-if-te-0/16) # 4

  Output Dell(conf-if-te-0/16) #.

  Traffic from servers will follow the path of the VLAN. For example, if an internal server, facing the port is set to VLAN 4, that traffic will be transmitted on the uplink port which has also set to VLAN 4.

  By default, all external ports are placed in a single whole LAG. However, you can change the configuration to support several shifts of uplink. Page 159 of guys configuration takes you step by step on setting up several shifts of uplink.

  The aggregator automatically configures to match the FCoE parameters used in the switches to which it connects through its uplink ports. FIP snooping is automatically configured on an aggregator. Automatically configured port channel (LAG 128) works CWF port mode. See page 86 for more information and examples of config.

  For redundancy, you could stack the units together. 241 page details the process of stacking.

  Page 54 of 102 of the Guide blade IO has one other diagram that details more internal server port mapping for each blade.

• Reference Dell MD3200i correct editing with IP system and the NIC for faster network speeds

  Hi all

  I worked on this project for a while now. I did a lot of research and have contacted Dell several times. I need help.

  I have 2 sets of identical to use for Hyper-V clusters servers. We bought a Dell MD3200i in November, we also bought a Dell 5424 switch and a Cisco SLM2048 switch. These servers have Real Tek 2 network cards for iSCSI Jumbo frames is 9 k

  The Dell MD3200i is two SAN controllers. Dell 5424 is the iSCSI optimized switch and Cisco is a 48 switch ports. iSCSI is on its own network that nothing else is connected to it. (There is an Iomega NAS and a promise Vtrak SAN Tech with all current domain of execution with iSCSI controller)

  Reference Dell MD3200i controller 0 Port 0 192.168.130.101 controller 1 Port 0 192.168.131.101

  Controller controller Port 1 0 192.168.130.102 1 1 192.168.131.102

  Controller controller Port 2 0 192.168.130.103 1 2 192.168.131.103

  Controller controller Port 3 0 192.168.130.103 1-3 192.168.131.104

  Cisco switch has 1 VLAN n ° 1 on it and the 130 subnet inside elements. There are 8 connections to the switch. 4 controller 0 and 1 of each of the servers. It has an IP of 192.168.132.4, but that switch IP does not make difference. Lighted Jumbo frames

  Dell switch has 2 of #1 for various things such as the domain controller, Vtrack, and SIN. Subnet 2 is 131 and has a total of 8 connectors inside. 4 in 1 controller and 1 from each of the servers. Lighted Jumbo frames. The switch IP address is 192.168.132.2

  Groups of servers. Each server node running Windows 2008 R2 SP1 and running hyper-v with virtual server clusters / storage folder on them. 2 Realtek NIC with Jumbo frames made 9 k ProdNode1 and ProdNode2 have 12 Core i7 CPU with 12 GB memory, EXNode1 and ExNode2 have 12 Core i7 CPU with 24 GB of memory.

  ProdNode1 iSCSI-1 192.168.130.110 ProdNode1 iSCSI-2 192.168.131.110

  ProdNode2 iSCSI-1 192.168.130.120 ProdNode2 iSCSI-2 192.168.131.120

  ExNode1 iSCSI-1 192.168.130.130 ExNode1 iSCSI-2 192.168.131.130

  ExNode2 iSCSI-1 192.168.130.140 ExNode2 iSCSI-2 192.168.131.140

  Portal discovery iSCSI on ProdNode1 went to 192.168.130.110 192.168.130.101 and 192.168.131.110 192.168.131.101 each of the other servers Discovery Portal have been pairs like this.

  iSCSI tab click on add 8 MPIO sessions at each of the ports on the MD3200i from Dell, target. For example, I added 1 session of 192.168.130.101 using it. Add Session,--> activate--> Advanced Mutlipath--> Local--> IP 192.168.130.110 initiator and target 192.168.131.101 iSCSI adapter. This is repeated on all servers. 4 connections for each NIC.

  The network is very slow. It revolved around 2 to 4 MB/MIN and it should be much faster. Initially, we had only the Cisco switch with only 1 VLAN and everything connected directly to it. I read somewhere that MPIO has been the problem, so I went through the same configuration but does not verify the MPIO checkbox above. Once this has been done, the network speed went up to 1.5 GB/Min but modular storage Dell was not happy, and virtual servers would fail and the connection is not very stable.

  What wrong with my setup? Can I directly home and fix the servers directly to the PowerVault and will make stable and allow for failover and redundancy NIC? I need to get this stable so I can move with something else.

  Thank you Ron

  You will need to change your system of intellectual property on this:

  rbramble

  EX-Node1 iSCSI-1 192.168.130.130

  EX-Node1 iSCSI-2 192.168.131.130

  EX-Node2 iSCSI-1 192.168.132.140

  EX-Node2 iSCSI-2 192.168.133.140

  Prod-Node1 iSCSI-1 192.168.130.10

  Prod-Node1 iSCSI-2 192.168.131.10

  Prod-Node2 iSCSI-1 192.168.132.20

  Prod-Node2 iSCSI-2 192.168.133.20

  Reference Dell MD3200i

  Controller 0 Port 0 - 192.168.130.101 Jumbo Frames 9K

  Controller 0 Port 1 - 192.168.131.101 Jumbo Frames 9K

  Controller 0 Port 2 - 192.168.132.101 Jumbo Frames 9K

  Controller 0 Port 3 - 192.168.133.101 Jumbo Frames 9K

  Controller 1 Port 0 - 192.168.130.102 Jumbo Frames 9K

  Controller Port 1 1 - 192.168.131.102 Jumbo Frames 9K

  Controller 1 Port 2 - 192.168.132.102 Jumbo Frames 9K

  Controller 1 Port 3 - 192.168.133.102 Jumbo Frames 9K

  Your iSCSI sessions will be:

  For EX-Node1:

  -192.168.130.130 to 192.168.130.101

  -192.168.130.130 to 192.168.130.102

  -192.168.131.130 to 192.168.131.101

  -192.168.131.130 to 192.168.131.102

  For EX-Node2:

  -192.168.132.140 to 192.168.132.101

  -192.168.132.140 to 192.168.132.102

  -192.168.133.140 to 192.168.133.101

  -192.168.133.140 to 192.168.133.102

  For Prod-Node1:

  -192.168.130.10 to 192.168.130.101

  -192.168.130.10 to 192.168.130.102

  -192.168.131.10 to 192.168.131.101

  -192.168.131.10 to 192.168.131.102

  For Prod-Node2:

  -192.168.132.20 to 192.168.132.101

  -192.168.132.20 to 192.168.132.102

  -192.168.133.20 to 192.168.133.101

  -192.168.133.20 to 192.168.133.102

• Reference Dell - never!

  I bought two computers in July 2009. I had problems with both of them. Inspiron mini had a problem with wireless, Dell said was my fault. and refused to fix it until I told them. I wanted to return it them. Finally they gave me a free support and support person said that there is something wrong with the computer I received.  Something other than the computer is unbalanced and wobbles when he types. I sent the compture to get fixed and it never got fixed.  I thought I would just deal with it because you get what you pay for.

  In January my XPS studio crashed. Screen has become sell contact of Virgin material and the damage. So I called dell. It took them a month to figure out, and indeed there is something wrong witht the computer. Thus broke computer I couldn't use it for a month. Finally I got the new memory and hard new dirve. The next day, my computer crashed. He spent a month trying to say Dell that something was wrong with my computer. All that time I spent 30-75 minutes on the phone with technical support. It was time that I called 4 days a week. I bought long and costly warrenties on my computer, including hardware and software. Not to mention cell phone chargers. Finally I conviced someone as my computer is really broken and they agreed to send me another computer. I'll go at least a computer that works. Understandable that it would take some time to get my replacement. My replacement date came and went. I called Dell again 45 minutes on the phone.  Then I've been transferred several times. The rep that I talked to said that they have not yet started doing my replacement.  It has been frustrating and I think that he was treated in a disrespectful way, what happened to quality customer service.

  On top of that today I was warned that even if the company has already approved my payment of $ 1,500, they now can't seem to find a record of the transaction and consider my past due account.  Also, they refused to refund my money and couldn't give me any assurance that the situation would be resolved.

  Anyone has any advice on the purchase of an Apple, I hear they have great customer service and wonderful tech support.

  I just wanted you to know that you aren't the only one with all these problems.  I am struggling with for more than a month to replace my computer. Finally, on March 1, they said they would and they have placed an order.  Now a week later it stil is not delivered because they can't find a 'HARD' for my computer.  REFERENCE DELL SUCKS AND I WIL NEVER BUY ANOTHER.    I put a post of "do NOT GET ALL the ANSWERS.

• Reference Dell 6224 and 5448

  Hi team,

  I'm new dell switches - exposed to cisco switches. I am faced with new kinds of problems with these dell switches. Unable to provide a fix and fight for the last 5 days. Pls help me. Below is my script

  Two nw - 2.0 and 3.0 is required to be configured in VLAN, VLAN ID 2 and 3.

  VLAN 2 - 192.168.2.1

  VLAN 3 - 192.168.3.1

  N/W 2.0 and 3.0 N/W machinery will be shared 48-Port powerconnect switch 5448 DELL

  The routing part arrives at 6224 power connect - gateway for vlan 2 - 192.168.2.1 and bridge for VLANs 3 - 192.168.3.1

  The switch of two is ascending through fiber optic - spf port cable

  This is the configuration I did-

  5448 switch-

  database of VLAN

  VLAN 2, 3

  output

  interface vlan 2

  switchport access vlan 2

  GVRP enable

  Routing

  output

  interface vlan 3

  switchport access vlan 3

  GVRP enable

  Routing

  output

  interface ethernet 1/you/1

  switchport mode general

  VLAN allowed switchport General add 2.3

  GVRP enable

  output

  interface ethernet 1/g1

  switchport access vlan 2

  GVRP enable

  output

  interface ethernet 1/g2

  switchport access vlan 3

  GVRP enable

  output

  Uplink port is TE1 (Layer 2) to XG2 (Layer 3)

  Reference Dell 6224 can connect

  Configure the terminal

  interface vlan 2

  no downtime

  IP 192.168.2.1 255.255.255.0

  Routing

  output

  interface vlan 3

  no downtime

  address 192.168.3.1 IP 255.255.255.0

  Routing

  output

  interface ethernet 1/xg2

  switchport mode general

  VLAN allowed switchport General add 2.3

  GVRP enable

  Computer with 192.168.2.100 / 24 GW 192.168.2.1 connected to layer 2 switch g1 - vlan 2

  When I ping 192.168.2.1 - accessible United Nations host destination

  Even the wise

  Computer with 192.168.3.100 / 24 GW 192.168.3.1 connected to layer 2 switch g1 - vlan 3

  When I ping 192.168.3.1 - accessible United Nations host destination

  Any thing that has missed out in the configuration part / all bad entries. I'm not sure now how to treat this. Pls help me and it is an urgent task for me

  Thank you

  With multiple VLANs, you need to use the general/Trunk mode. With the help of the info we have I made a diagram to help show the location of the switches and parameters on them. Obviously things can be different, such as PVID, IP address, VLAN ID etc are all customizable to your needs. But the page layout modes and the port will remain the same.

  

  STP will not fill the VLAN on the other switches. It's probably the GVRP feature it refers. With such a short race, it is more practical to manually add the VLAN. At least for the initial Setup, then once everything works enable GVRP to accommodate future expansion of VLAN.

  Hope this helps some.

• Reference Dell place 8 pro and 3g mobile hotspot

  Hey dell community.

  I have a place of reference dell 8 pro and I tried to get my Tablet for work with the mobile hotspot!

  When I plugged it it will say limited.

  None fixes please?

  Bobby Burgess

  Hi Bobby,.

  I found this thread on the venue Pro 8 and of connection to wireless networks / hot spots.  Try the suggestion in this thread and see if it helps.

  NOTE: I copied on the steps of resolution here as well in case anyone wants to see it.

  When sometimes, I had this problem, a deep discharge set: with power supply not connected, press the button of the Tablet for 30 or 60 seconds, including after the Tablet died;  Let the Tablet turned off for 2 minutes; and restart.  Have been informed by Support technique Dell that the cause is a buildup of static electricity, which avoids deep discharge.

  Todd

• DELL INSPIRON 2320 - Natural Wireless Laser Keyboard 7000 - default value is | Caps lock | WE (turned on) in all fields of password

  Hi y ' All

  DELL INSPIRON 2320 - Natural Wireless Laser Keyboard 7000 - default is Caps Lock ON (active) only when the cursor is in a field of password.

  The game of keyboard mouse 7000 is great.

  However, when the cursor is in any field/bos where a password must came me in, CapLock default value (setting) is ON or activated.

  • This only happens only in a field/area requiring a password to enter... but it happens each unique time, any application or what connection Web site password field I can be located anywhere on the Internet.
  • Again, this is only a problem when the cursor is in a password field.
  • This (setting) can be reversed that, when the cursor is in an area of password, default (setting) will be | Caps Lock |  STOP =?

  In the BIOS settings, I only find a selection of NumLock setting.  In Centre of keyboard and Microsoft mouse, the only setting that I can locate offers the choice to enable or disable the use of the Caps Lock key... entirely.  So, when turned on, the default value is lock shift = WE only in a password box.  Know, I is not no accidentally redundant; I repeat this case specific to the question in order to stress that this is the only time only this question.

  Like most people, I have to enter the password often. This problem occurs if the "remember me" or "keep me logged in" is selected.

  It's much more irritating.

  Thank you for your considerations and possible solutions, if any.

  Bobby

  1. Dell Inspiron 2320
  2. Windows Pro V.7.0
  3. Microsoft Natural Wireless Laser Mouse 7000

  #      #      #

  end of post

  Hello

  To turn off the caps from the BIOS lock, you will need to contact the manufacturer of the BIOS.

  Note: Update of the BIOS can be a complicated process, and if an error occurs, your computer could be rendered unusable. Be sure to observe the instructions of the manufacturer.

  Reference:

  http://support.Microsoft.com/kb/894037?WA=wsignin1.0

  It will be useful.

• Reference Dell 1700 crashed and I have no backup

  Reference Dell 1700 crashed without backup whats a girl to do
  
  

  lost all programs can run does not help

  Reference Dell 1700 crashed without backup whats a girl to do

  
  

  lost all programs can run does not help

  Reinstall Wndows.

  Reinstall all your programs from the original media or downloaded files you have saved on an external drive.

  Reinstall all your data from the backups that you made on an external drive.

  If you have not, you're out of luck.

• Reference Dell vostro 1520 with windows xp prof... Not reading CD/DVD

  Reference Dell vostro 1520 with windows xp prof... Unable to read & play any cd/dvd.tried mr.fixit content but no solution at the moment.

  Hello

  1 have. what fixit you tried?
  2. don't you make changes to the computer before the show?

  Your CD or DVD drive is missing or is not recognized by Windows or other programs
  http://support.Microsoft.com/kb/982116

  Important: To do: Important This section, method, or task contains steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click on the number below to view the article in the Microsoft Knowledge Base: 322756 (http://support.microsoft.com/kb/322756/) how to back up and restore the registry in the window.

• Cannot print. Reference Dell 944 communication usb port is not available. error check your firewall settings to ensure the printer communication is not blocked.

  Original title: unable to print. Reference Dell 944 communication usb port is not available.

  Message says 'check your firewall settings to ensure the printer communication is not blocked. Printer has worked faithfully until the problems started with the XP Home operating system. To cut a long story short ram upgraded to 2 GB, all unnecessary programs identified and technician Microsoft contacted to solve problems.  I was informed of problems caused by 3rd software party conflicts. Kaspersky was apparently the culpit. Dell Inspiron 32 now much faster but the printer will not work little matter what I do. I tried to reload with drivers & utility CD, drivers uninstalled & reinstalled on the site of all nothing is? Can someone help?

  DavidNicholsonXN,

  How to download and install drivers in the correct order

  also try to read...

  The owners of all-in-one printer Dell 944 thread (W7)

  Let the printer after Kaspersky

  Rick