Reference Dell C6100 Question

Similar Questions

• Reference Dell 2209WA questions

  I was given a Dell 2209WA monitor a few days ago. And I'm having a few problems. On the one hand, if I plug a vga cable through my computers DVI (with a DVI - VGA) adapter port, the monitor works fine. If I try right DVI, I get no fArrondi of VGA cable. I installed the drivers for the monitor, and it shows in my Windows 7 install x 6 Dell 2209WA - Analog.  I prefer to use the digital configuration.

  In addition, in agalog, all the controls are locked, I can't change anything. Is it possible to unlock these controls in analog mode? I also couldn't find the serial number anywhere on the screen.

  Hi Cbx_sympamandu93,

  Please check the picture below to locate the bar code data plate and the regulatory label on the monitor. This monitor has no serial number. Service tag is usually available for the monitors that are 24 inches and above in size. For more information, please consult the FAQ of monitors: http://dell.to/W7nRu0

  In addition, it seems that the OSD Menu on the screen is locked because of which you are not able to change the display of monitor settings. The menu lock allows you to control access to the settings. When you select Lock, no user adjustments are allowed.

  Please follow these steps to unlock the OSD Menu:

  Press and hold the Menu button for 10-15 seconds to unlock. If this does not work, try the following steps:

  • Press Menu OSD button.
  • Access the option "other settings".
  • Below, select the "Menu Lock" option to the right and select 'Unlock'
  • Now, the Menu OSD is unlocked and you can change the settings of the monitor.

  Once you have followed the steps above, it is likely to work the way you want. You can also consult the manual for the monitor that has its complete installation and usage guide according to what you can make changes and setup the screen or using the cable VGA or DVI from this link: http://bit.ly/WdQpY0

  Please come back for any clarification.

• Reference Dell M1000e + aggregator MI/O port mapping

  Hi all

  I intend to install a new chassis Dell M1000e with Dell M/o aggregator. During the time of solution, I have a few questions about correspondences between the physical uplink with NDC blade ports ports. A Please check the config below and specify my queries?

  My hardware:

  • 1 x Dell M1000e
  • 2 x M i/o aggregator (A1 & A2)
  • 16 x M630 Blade (Qlogic 57840 S ANC four ports card)

  Reference DELL M/o aggregator:

  (reserved for Future use) module QSFP + 2 ports (Port No1:33 - 36 & No2:37 Port-40)

  I want to use these two modules for my blades 4-port Quad and the confusion I had, how to associate these 16 ports (8 ports of each module) to the server blade and the amount of bandwidth I will get by blade with redundancy.

  Module 4-port SFP + 10 GbE (Flexi-O of the Bay) (Port No.: 41-48)

  Module 4-port 2/4/8 Gb FC FlexIO (Flexi Bay 1) (Port No.: 49-56)

  FYI - I would like to install ESXi 6.0 on all blades

  Thank you!!

  Vinay

  Oriented server ports are configured automatically as part of the aggregation of links groups if the server is configured for the LACP Protocol. Static GAL is not supported.

  You will use the segregation network VLAN. A VLAN for network traffic and the other for the CF. Here are the commands to configure interfaces for different VLANS.

  Unidentified:

  Dell (conf) # tengigabit interface 0/16

  Dell(conf-if-te-0/16) # vlan unidentified 4

  Output Dell(conf-if-te-0/16) #.

  Tag:

  Dell (conf) # tengigabit interface 0/16

  The tag vlan Dell(conf-if-te-0/16) # 4

  Output Dell(conf-if-te-0/16) #.

  Traffic from servers will follow the path of the VLAN. For example, if an internal server, facing the port is set to VLAN 4, that traffic will be transmitted on the uplink port which has also set to VLAN 4.

  By default, all external ports are placed in a single whole LAG. However, you can change the configuration to support several shifts of uplink. Page 159 of guys configuration takes you step by step on setting up several shifts of uplink.

  The aggregator automatically configures to match the FCoE parameters used in the switches to which it connects through its uplink ports. FIP snooping is automatically configured on an aggregator. Automatically configured port channel (LAG 128) works CWF port mode. See page 86 for more information and examples of config.

  For redundancy, you could stack the units together. 241 page details the process of stacking.

  Page 54 of 102 of the Guide blade IO has one other diagram that details more internal server port mapping for each blade.

• Reference Dell Sonicwall SRA

  Hey guys, more of a statement than a question. If you have a Dell Sonicwall and users do "found no appropriate group" of course the same user does not exist as a local user and a domain user. This will cause problems. Took me a while to understand that >.<>

  Good thought.

  Thank you
  Ben D
  Reference Dell SonicWall
  #Iwork4dell

• Reference Dell Force10 S50N time in the same newspaper

  Hello

  first of all, I hope that a good place to ask question re Force10 devices - if not please forgive & point me to the right place

  I have following two stacked devices:

  Type of system: S50N
  Reference Dell Force10 operating system Version: 1.0
  Reference Dell Force10 Application Software Version: 8.4.2.6

  Recently, I have configured a source of time using ntp. display the clock command returns good time & ntp config also seem ok.

  I want to have the switch which had the correct timestamp of the date unit % hour however when logging to show browsing results shows this:

  32w6d12h: STKUNIT1% m: % LACP CP...
  32w6d12h: STKUNIT1% m: % LACP CP...
  32w6d12h: % STKUNIT1-% M:CP CMEA...

  That I am, I lack to set up/set for the date & time stamped and posted in the event logs?

  (I'm beginner in world Force10 and switch)

  Appreciate any help

  Hello

  I found horodateurs service order before but I was so blind to enter config mode.

  That worked very well.

  Thank you very much

• Reference Dell MD1200, H710 with R720XD

  Hello

  Asked if drieves NL - Seagate SAS (ST4000NM0023) can be used in the following configuration.

  Reference Dell Perc H710 + PowerEdge R720XD MD1200.

  The answer that I gave them was who should be tested. Because in documentation it is stated that mark Dell hard disks should be used.

  I know that some controllers Perc will give a warning each time if not dell disks are used, but they work without problems. Is this the case even when you use a box MD1200?

  Kind regards

  Indrek

  INDRP,

  You're right that only some drives are tested and supported in the bays of the MD. Here is a link that will take you to one of the manuals that list all drives supported for 1200 MD and MD1220.

  FTP.Dell.com/.../PowerVault-md1200_Reference%20Guide_en-US.pdf

  Please let me know if you have other questions I would be happy to help.

• Reference Dell 1700 crashed and I have no backup

  Reference Dell 1700 crashed without backup whats a girl to do
  
  

  lost all programs can run does not help

  Reference Dell 1700 crashed without backup whats a girl to do

  
  

  lost all programs can run does not help

  Reinstall Wndows.

  Reinstall all your programs from the original media or downloaded files you have saved on an external drive.

  Reinstall all your data from the backups that you made on an external drive.

  If you have not, you're out of luck.

• Reference Dell vostro 1520 with windows xp prof... Not reading CD/DVD

  Reference Dell vostro 1520 with windows xp prof... Unable to read & play any cd/dvd.tried mr.fixit content but no solution at the moment.

  Hello

  1 have. what fixit you tried?
  2. don't you make changes to the computer before the show?

  Your CD or DVD drive is missing or is not recognized by Windows or other programs
  http://support.Microsoft.com/kb/982116

  Important: To do: Important This section, method, or task contains steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click on the number below to view the article in the Microsoft Knowledge Base: 322756 (http://support.microsoft.com/kb/322756/) how to back up and restore the registry in the window.

• Cannot print. Reference Dell 944 communication usb port is not available. error check your firewall settings to ensure the printer communication is not blocked.

  Original title: unable to print. Reference Dell 944 communication usb port is not available.

  Message says 'check your firewall settings to ensure the printer communication is not blocked. Printer has worked faithfully until the problems started with the XP Home operating system. To cut a long story short ram upgraded to 2 GB, all unnecessary programs identified and technician Microsoft contacted to solve problems.  I was informed of problems caused by 3rd software party conflicts. Kaspersky was apparently the culpit. Dell Inspiron 32 now much faster but the printer will not work little matter what I do. I tried to reload with drivers & utility CD, drivers uninstalled & reinstalled on the site of all nothing is? Can someone help?

  DavidNicholsonXN,

  How to download and install drivers in the correct order

  also try to read...

  The owners of all-in-one printer Dell 944 thread (W7)

  Let the printer after Kaspersky

  Rick

• Reference Dell pc with xp family. Restart to the logon screen

  Reference Dell pc with xp family. Restart to the logon screen. starts ok in safe mode. run msconfig and do that no change then do restart ok everything ok until the cold start, then hand it to restart?

  Peek into the registry to find clues.

  Disable the automatic restart in case of system error and see if you can capture a message of error checking bug (BSOD) with useful information.  Automatic restart in the event of system failure can be disabled in the F8 advanced boot menu, or you can turn it off in system properties.

  1. right click on my computer and select Properties.
  2 - Click on the Advanced tab, and then click on the Start button and recovery settings.
  3 clear the automatically restart box and OK your way out system properties.

  Start the computer in a Clean Boot State, if the computer starts successfully in a clean boot state, then one of your user programs most likely problems, look in the case of journal of indexes.

  How to configure Windows XP to start in a "clean boot" State
  John

• Reference DELL T420 - battery on PERC H710 adapter controller

  Hello

  I received a yellow warning

  Reference DELL T420 'Battery on PERC H710 adapter controller'

  What it means?

  What should I do?

  Order the new battery?

  It is a simple replacement mission?

  Is it essential?

  Update:

  test URL

  http://www.Dell.com/support/article/us/en/04/SLN130018

  Have nothing, everything seems fine now...

  Thank you

  It is normal so he can make a full discharge of the battery as part of his learning cycle every 90 days. Make sure that this isn't that. If this isn't the case, the reason, give it 24 hours. If it is fully charged, update the system (including RAID firmware, driver first) firmware. If not fully charged yet or it reproduces quickly, then replace the battery - power down to replace.

• Reference Dell 3110cn of Laserjet + os El Capitan

  My MacBook Pro (2009) stopped my Dell printer. News on this please.

  Hi deaconjo,

  as I had the same problem, I found a solution for my El Capitan MacPro 2008:

  Search for the following installation program:

  3130cn_Installer_And_Application_Dell_A04_MAC.dmg

  Inside this package you will find the driver for 10.7 and higher. After installing the package I could add an IP printer with this driver:

  Reference Dell 3130cn Color Laser v3017.104 PS

  With this driver installed, I can use my printer Dell 3110cn without problem.

  Perhaps it might help you too.

  Concerning

• Reference Dell 2007FP vs HP zr22w

  Hi guys, I use t410s now. You want to find an IPS monitor. Currently have two choices.

  Reference Dell 2007FP (handed to nine 30-day warranty) $95

  HP zr22w (new, 3-year warranty) $175

  What would be a good choice?

  Not for the game.

  But need good color, good text, Word process, sometimes a movie.

  The HP zr22w DP, is better than the VGA to connect to my T410s?

  

  Thank you!

  Your information is so helpful. But I think that I can not check the number helpfully I ordered from DELL FINANCIAL SERVICES. Thank you very much!

• Reference Dell place 8 just out of warranty and dead now?

  Hello

  Everyone has a glue on Earth how to contact Dell technical support? My Tablet has acted weird for a while, but now it is completely dead and the custom lights at all. Previously, I got past pressing buttong for 10-15 minutes sometimes and then after a while it just turns itself off again. So now it's offshore and dead.

  I searched web pages of Dell support for direct contacts, but not luck. And worse, that it turns out that the warranty has ended in 12/09/14

  What a *.

  Reference Dell of mobile devices (phones) & tablets
  1-800-308-3355 24 / 7

  http://www.Dell.com/support/contents/us/en/19/category/contact-information/technical-support?c=us&l=en&s=DHS&CS=19

• Reference Dell E6420 randomly not SSD detection at startup

  Specifications of the computer:

  Dell Latitude E6420, Intel Core i5 2520 M, 2 x 4 GB = 8 GB of RAM, Nvidia NVS 4200 M, 250GB HDD, Win 7 Pro 64, Bios A23

  The value of operation SATA AHCI and not quick start. I have 3 of these computers. They are all out of warranty.

  I replaced the original 7mm Hitachi 250 GB for the Intel 535 240 GB SSD HARD drive.

  I used Acronis True Image 2016 to clone the hard disk SSD. Cloning process is very much like on any other computer.

  The problem is that each cold 4 or 5 boots the computer cannot find the SSD drive. Restarting the computer solves the problem of that time. I have to find a solution. I want to sell them with a SSD and not with a HARD drive.

  I tried the things:

  Update the Bios of the A14 to A23.

  Put a spacer of 2mm on the SSD and of course the resettlement of the SSD.

  Exchange for another Intel 535 120 and 240 GB.

  Clean install of windows I knew was a waste of time because it does not affect the BIOS does not detect not things.

  Googling the problem for hours.

  Call dell?

  Use another brand of SSD? He probobly won't make any difference to look at other threads.

  Use a HARD drive? Last resort. I can't stand slow hard disks regularly.

  Reference Dell E6420 seems to work with a Samsung 850 Evo 250 GB instead of the Intel 535 very well. Tested over a period of 3 months with no problems. Threw 535 readers intel in the desktop instead.