Reference Dell Equallogic

Similar Questions

• Reference Dell EqualLogic 6010 initial configuration

  Hello. I have a dust collection Dell EqualLogic 6010 in my test harness. He was sent by another office, for reasons unknown. I would use this feature to unload a few backup copies of vm in the development of our san to this device of 16 smaller disk.  I only have one switch that comes with it, but for its intended use, this should be good. I only will link a physical server to it where my backup software. (I wish I could just direct connect, but I read that it is not possible, or at least not recommended) The problem is... I don't know where to start.

  I tried to put in place of guides, manuals and Setup guides, but the single pdf I find is more on limits, best practices, what he can do, etc., rather than from step 1. (like, indications which include the implementation of rails and all that usually skip us... lol) Can anyone help with a quick course guide or accident? Maybe point me in the direction of certain documents?

  For example... series in I do? If so, what are the default creds? There may be a default ip address that I can connect my laptop in to start the initial game up? Or y at - it a config that I can run on the same subnet as EMC VNX implemented who will find unconfigured devices? I really can't find any of this set up information of this device. I hope someone can help.

  Thank you very much. :)

  Hello

  You have a username on the EQL support site?   The documentation is a quick installation guide.

  1.), you can use the serial port.  9600,8, n, 1 NO flowcontrol.   (Series cisco cables do not work)   Grpadmin default login, password grpadmin. (assuming that it has not already been implemented)

  2.) If you have an EQL support account, you can also download the HIT for Windows or Linux.   Who has the Remote Installation Wizard software.  Who will scan the local subnet for the not configured matrices.  Then allow you to configure it through the user interface.

  Re: switches.  You need a 10GbE switch.  The 6010 will not negotiate until 1GbE.

  Kind regards

• Reference Dell EqualLogic Multipath (e/s high flow)

  We recently bought a Dell EqualLogic SAN. Our main goal for this device was to begin to use pools of resources and be able to do a few HA and Live migration. We have worked with XenServer and Xen Cloud for a while and got no e/s on iScsi performance we were hoping for. With the help of Multipath on the main host machine we get on 250 Mbps (which we are satisfied). On the guest computers, we get only 120 Mbps.

  My question to the community of VMWare; If we wanted to use products VMWare is the possibility to get more then 1 Gbps i/o throughput on a guest PC? And if so, if it is a PDF or a post somewhere that could explain how to do this?

  Let me know, thanks!

  Clinton

  The doc of the correct configuration is attached... hope that her little help. In my view, it is also sub TR docs when you save your table PS.

• Reference Dell Equallogic Interface errors

  Hi guys, I got a big problem here in my room. My equallogic iscsi interfaces have a lot of erros. What can be?

  

  First of all, make sure you run the latest version of FW and SANHQ table.

  Packet errors are often the cause of bad cable, bad switch ports and a misconfiguration on switch iSCSI ports.   The only way to erase the mistakes of packages on Equallogic arrays must restart the table.

  • Replacement cable between the controller port and switch port with known good cable.

  • 10 GB cables must be SFF-8472 compliant to work with 10 GB Equallogic arrays.

  • Confirm that the switch is a minimum firmware to work with Berry Equallogic en.community.dell.com/.../2661.equallogic-compatibility-matrix

  (Note: if unable to switch, you can disable protocols spanning tree on ports connect to the table).

  • Use the tech TR1017 report to verify the configuration of the switch and confirm it meets best practices.

  • Run a show of support on the switches to review port errors.   If a Powerconnect or Force10 switch then engage networks dell help examine the switch logs. If another provider, and then engage the seller to switch to help examine the switch logs.

  • Cards network host to firmware update and the latest network card driver

  • The direct link to TR1017:

  Media.Community.Dell.com/.../tr1017-v4-Network-Guidelines.pdf

  If the host Linux with Multipath.d, you may need to modify the multipath.conf file to include: tur path_checker in the devices section.

  Joe

• Reference Dell EqualLogic Powershell Script & replicas

  Hi all

  I develop a script to extract information on replicas made between two bays EQL PS Series Dell.

  For each volume, I keep a history of 10 aftershocks, I use the following command to display all the replicas made of a specific volume.

  > get-eqlreplica - GroupName SANPROD - ReplicationSite SANBCK - VOLUME VolumeName

  But I'm unable to get the size for each replica. Is it possible to do this with the cmdlet provided by Dell?

  Thanks for your help!

  Currently the cmd - allows PowerShell does not size of replication data.  For now, only the GUI and the SANHQ can show you the size of each replication.

  -joe

• Reference Dell EqualLogic HIT/VSM - VMware license terms.

  Hello.

  I read the release notes of Virtual Storage Manager 4.0, vSphere, conditions of licence, they are required:

  License terms for vSphere
  VSM comes with licenses and the following features:

  VSM: VSphere license any

  VASA: vCenter 5.0 or later version, ESXi 4.0 or later, any vSphere license
  In addition, the storage array firmware allows use the following features that VSM is installed:

  vStorage API for integration (VAAI) table: business, Enterprise Plus on ESXi license
  4.1 or later.

  Issues related to the:

  1. I'll be able to run VSM with vSphere Essentials Plus? VAAI at least requires vSphere Enterprise License. What are the consequences if I deploy with vSphere Essentials Plus.

  2 VSM supports ESXi 5.5 U2?

  Thank you

  Paul

  VASA is a feature you don't need basic VSM features.  Which is what the release notes are trying to say.   VASA allows VMware request more information on storage volumes.   I.e. through VASA VCS calls can show that a volume is RAIDed storage, integrates snapshots or replicas.   Currently, the usefulness of the VASA is limited, even when it is available.   VASA is the first step to VMware to better understand a storage array capabilities. More features will be coming in future versions of ESXi.

  However, to make the VASA work any, the storage provider must provide software 'glue' for specific HW calls of a query of VCS.   VSM, is what has the code, known as a "provider of VASA.   A translator of sorts.

  Kind regards

• Dell Equallogic PS5000X NIC reference

  Hello

  does anyone have experience of SAN Dell Equallogic PS5000X?  I'll put in place at the moment and it seems there are 2 controllers for all of the 3 NIC (6 in total).  I find I cannot use 3 cards and 1 controller in Active mode and can not find a way to get the two controllers to work in unison and the two assets.

  I wanted to use 4 network cards for iSCSI traffic on a VLAN giving a rate 4 GB of storage but you can use 2 network cards, giving a throughput of 2 GB and 1 for management.

  Is this the only method available for this type of SAN?

  Any advice would be greatly appreciated.

  Andy

  Hey,.

  The PS is an active / standby. A controller is active. The other will be the shot if the first of all a problem. You have only a configuration to do.

  You configure 3 interfaces in the GUI. eth0, 1, 2.

  The second controller will use this interface when you need.

  You can dedicate a management port, but Dell recommends that you connect all of your ports to the ISCSI network.

  Hope this helps

  Please consider my response as 'useful' or 'proper' marking

• Reference Dell 1700 crashed and I have no backup

  Reference Dell 1700 crashed without backup whats a girl to do
  
  

  lost all programs can run does not help

  Reference Dell 1700 crashed without backup whats a girl to do

  
  

  lost all programs can run does not help

  Reinstall Wndows.

  Reinstall all your programs from the original media or downloaded files you have saved on an external drive.

  Reinstall all your data from the backups that you made on an external drive.

  If you have not, you're out of luck.

• Reference Dell vostro 1520 with windows xp prof... Not reading CD/DVD

  Reference Dell vostro 1520 with windows xp prof... Unable to read & play any cd/dvd.tried mr.fixit content but no solution at the moment.

  Hello

  1 have. what fixit you tried?
  2. don't you make changes to the computer before the show?

  Your CD or DVD drive is missing or is not recognized by Windows or other programs
  http://support.Microsoft.com/kb/982116

  Important: To do: Important This section, method, or task contains steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click on the number below to view the article in the Microsoft Knowledge Base: 322756 (http://support.microsoft.com/kb/322756/) how to back up and restore the registry in the window.

• Cannot print. Reference Dell 944 communication usb port is not available. error check your firewall settings to ensure the printer communication is not blocked.

  Original title: unable to print. Reference Dell 944 communication usb port is not available.

  Message says 'check your firewall settings to ensure the printer communication is not blocked. Printer has worked faithfully until the problems started with the XP Home operating system. To cut a long story short ram upgraded to 2 GB, all unnecessary programs identified and technician Microsoft contacted to solve problems.  I was informed of problems caused by 3rd software party conflicts. Kaspersky was apparently the culpit. Dell Inspiron 32 now much faster but the printer will not work little matter what I do. I tried to reload with drivers & utility CD, drivers uninstalled & reinstalled on the site of all nothing is? Can someone help?

  DavidNicholsonXN,

  How to download and install drivers in the correct order

  also try to read...

  The owners of all-in-one printer Dell 944 thread (W7)

  Let the printer after Kaspersky

  Rick

• Reference Dell pc with xp family. Restart to the logon screen

  Reference Dell pc with xp family. Restart to the logon screen. starts ok in safe mode. run msconfig and do that no change then do restart ok everything ok until the cold start, then hand it to restart?

  Peek into the registry to find clues.

  Disable the automatic restart in case of system error and see if you can capture a message of error checking bug (BSOD) with useful information.  Automatic restart in the event of system failure can be disabled in the F8 advanced boot menu, or you can turn it off in system properties.

  1. right click on my computer and select Properties.
  2 - Click on the Advanced tab, and then click on the Start button and recovery settings.
  3 clear the automatically restart box and OK your way out system properties.

  Start the computer in a Clean Boot State, if the computer starts successfully in a clean boot state, then one of your user programs most likely problems, look in the case of journal of indexes.

  How to configure Windows XP to start in a "clean boot" State
  John

• Module Extension Dell EqualLogic Multipathing v1.4 missing setup.pl

  The new v1.4 Dell EqualLogic Multipathing Module of Extension is missing setup.pl script.

  Hello

  Thank you.  A new package is created.  In the meantime, you can try the setup.pl v1.3...   Or use alternative methods to install it.

  Feel free to open a support on this file as well.   They can add you the question open with genius.

  Kind regards

  Don

• Reference Dell M1000e + aggregator MI/O port mapping

  Hi all

  I intend to install a new chassis Dell M1000e with Dell M/o aggregator. During the time of solution, I have a few questions about correspondences between the physical uplink with NDC blade ports ports. A Please check the config below and specify my queries?

  My hardware:

  • 1 x Dell M1000e
  • 2 x M i/o aggregator (A1 & A2)
  • 16 x M630 Blade (Qlogic 57840 S ANC four ports card)

  Reference DELL M/o aggregator:

  (reserved for Future use) module QSFP + 2 ports (Port No1:33 - 36 & No2:37 Port-40)

  I want to use these two modules for my blades 4-port Quad and the confusion I had, how to associate these 16 ports (8 ports of each module) to the server blade and the amount of bandwidth I will get by blade with redundancy.

  Module 4-port SFP + 10 GbE (Flexi-O of the Bay) (Port No.: 41-48)

  Module 4-port 2/4/8 Gb FC FlexIO (Flexi Bay 1) (Port No.: 49-56)

  FYI - I would like to install ESXi 6.0 on all blades

  Thank you!!

  Vinay

  Oriented server ports are configured automatically as part of the aggregation of links groups if the server is configured for the LACP Protocol. Static GAL is not supported.

  You will use the segregation network VLAN. A VLAN for network traffic and the other for the CF. Here are the commands to configure interfaces for different VLANS.

  Unidentified:

  Dell (conf) # tengigabit interface 0/16

  Dell(conf-if-te-0/16) # vlan unidentified 4

  Output Dell(conf-if-te-0/16) #.

  Tag:

  Dell (conf) # tengigabit interface 0/16

  The tag vlan Dell(conf-if-te-0/16) # 4

  Output Dell(conf-if-te-0/16) #.

  Traffic from servers will follow the path of the VLAN. For example, if an internal server, facing the port is set to VLAN 4, that traffic will be transmitted on the uplink port which has also set to VLAN 4.

  By default, all external ports are placed in a single whole LAG. However, you can change the configuration to support several shifts of uplink. Page 159 of guys configuration takes you step by step on setting up several shifts of uplink.

  The aggregator automatically configures to match the FCoE parameters used in the switches to which it connects through its uplink ports. FIP snooping is automatically configured on an aggregator. Automatically configured port channel (LAG 128) works CWF port mode. See page 86 for more information and examples of config.

  For redundancy, you could stack the units together. 241 page details the process of stacking.

  Page 54 of 102 of the Guide blade IO has one other diagram that details more internal server port mapping for each blade.

• Reference DELL T420 - battery on PERC H710 adapter controller

  Hello

  I received a yellow warning

  Reference DELL T420 'Battery on PERC H710 adapter controller'

  What it means?

  What should I do?

  Order the new battery?

  It is a simple replacement mission?

  Is it essential?

  Update:

  test URL

  http://www.Dell.com/support/article/us/en/04/SLN130018

  Have nothing, everything seems fine now...

  Thank you

  It is normal so he can make a full discharge of the battery as part of his learning cycle every 90 days. Make sure that this isn't that. If this isn't the case, the reason, give it 24 hours. If it is fully charged, update the system (including RAID firmware, driver first) firmware. If not fully charged yet or it reproduces quickly, then replace the battery - power down to replace.

• Reference Dell 3110cn of Laserjet + os El Capitan

  My MacBook Pro (2009) stopped my Dell printer. News on this please.

  Hi deaconjo,

  as I had the same problem, I found a solution for my El Capitan MacPro 2008:

  Search for the following installation program:

  3130cn_Installer_And_Application_Dell_A04_MAC.dmg

  Inside this package you will find the driver for 10.7 and higher. After installing the package I could add an IP printer with this driver:

  Reference Dell 3130cn Color Laser v3017.104 PS

  With this driver installed, I can use my printer Dell 3110cn without problem.

  Perhaps it might help you too.

  Concerning