Reference Dell Equallogic Interface errors

Similar Questions

• Reference Dell EqualLogic 6010 initial configuration

  Hello. I have a dust collection Dell EqualLogic 6010 in my test harness. He was sent by another office, for reasons unknown. I would use this feature to unload a few backup copies of vm in the development of our san to this device of 16 smaller disk.  I only have one switch that comes with it, but for its intended use, this should be good. I only will link a physical server to it where my backup software. (I wish I could just direct connect, but I read that it is not possible, or at least not recommended) The problem is... I don't know where to start.

  I tried to put in place of guides, manuals and Setup guides, but the single pdf I find is more on limits, best practices, what he can do, etc., rather than from step 1. (like, indications which include the implementation of rails and all that usually skip us... lol) Can anyone help with a quick course guide or accident? Maybe point me in the direction of certain documents?

  For example... series in I do? If so, what are the default creds? There may be a default ip address that I can connect my laptop in to start the initial game up? Or y at - it a config that I can run on the same subnet as EMC VNX implemented who will find unconfigured devices? I really can't find any of this set up information of this device. I hope someone can help.

  Thank you very much. :)

  Hello

  You have a username on the EQL support site?   The documentation is a quick installation guide.

  1.), you can use the serial port.  9600,8, n, 1 NO flowcontrol.   (Series cisco cables do not work)   Grpadmin default login, password grpadmin. (assuming that it has not already been implemented)

  2.) If you have an EQL support account, you can also download the HIT for Windows or Linux.   Who has the Remote Installation Wizard software.  Who will scan the local subnet for the not configured matrices.  Then allow you to configure it through the user interface.

  Re: switches.  You need a 10GbE switch.  The 6010 will not negotiate until 1GbE.

  Kind regards

• Reference Dell EqualLogic Multipath (e/s high flow)

  We recently bought a Dell EqualLogic SAN. Our main goal for this device was to begin to use pools of resources and be able to do a few HA and Live migration. We have worked with XenServer and Xen Cloud for a while and got no e/s on iScsi performance we were hoping for. With the help of Multipath on the main host machine we get on 250 Mbps (which we are satisfied). On the guest computers, we get only 120 Mbps.

  My question to the community of VMWare; If we wanted to use products VMWare is the possibility to get more then 1 Gbps i/o throughput on a guest PC? And if so, if it is a PDF or a post somewhere that could explain how to do this?

  Let me know, thanks!

  Clinton

  The doc of the correct configuration is attached... hope that her little help. In my view, it is also sub TR docs when you save your table PS.

• Reference Dell EqualLogic Powershell Script & replicas

  Hi all

  I develop a script to extract information on replicas made between two bays EQL PS Series Dell.

  For each volume, I keep a history of 10 aftershocks, I use the following command to display all the replicas made of a specific volume.

  > get-eqlreplica - GroupName SANPROD - ReplicationSite SANBCK - VOLUME VolumeName

  But I'm unable to get the size for each replica. Is it possible to do this with the cmdlet provided by Dell?

  Thanks for your help!

  Currently the cmd - allows PowerShell does not size of replication data.  For now, only the GUI and the SANHQ can show you the size of each replication.

  -joe

• Reference Dell EqualLogic HIT/VSM - VMware license terms.

  Hello.

  I read the release notes of Virtual Storage Manager 4.0, vSphere, conditions of licence, they are required:

  License terms for vSphere
  VSM comes with licenses and the following features:

  VSM: VSphere license any

  VASA: vCenter 5.0 or later version, ESXi 4.0 or later, any vSphere license
  In addition, the storage array firmware allows use the following features that VSM is installed:

  vStorage API for integration (VAAI) table: business, Enterprise Plus on ESXi license
  4.1 or later.

  Issues related to the:

  1. I'll be able to run VSM with vSphere Essentials Plus? VAAI at least requires vSphere Enterprise License. What are the consequences if I deploy with vSphere Essentials Plus.

  2 VSM supports ESXi 5.5 U2?

  Thank you

  Paul

  VASA is a feature you don't need basic VSM features.  Which is what the release notes are trying to say.   VASA allows VMware request more information on storage volumes.   I.e. through VASA VCS calls can show that a volume is RAIDed storage, integrates snapshots or replicas.   Currently, the usefulness of the VASA is limited, even when it is available.   VASA is the first step to VMware to better understand a storage array capabilities. More features will be coming in future versions of ESXi.

  However, to make the VASA work any, the storage provider must provide software 'glue' for specific HW calls of a query of VCS.   VSM, is what has the code, known as a "provider of VASA.   A translator of sorts.

  Kind regards

• Reference Dell Equallogic

  One possible part of several groups?

  No, this is not possible.

  It cannot also be a member of multiple storage pools

• Error adding array manager - VSphere 4, 4 SRM and Dell Equallogic

  I have built a new VSphere 4 of 2003 server and that you have installed SRM on it with one of Dell Equallogic SAN.  I'm point table configuration manager.  After I enter the information, then click on connect, I get the following error:

  Error occurred: XML Document is Empty

  I tried to run the installer with the repair option again and removed and added the SRA with no luck.

  Any help is appreciated.

  Just treat it today.  The plugin storage Dell is written in Java, so your Java executable needs to be in the path.  RDP on your SRM server and open a commandprompt.  If you can not simply run "Java.exe", you will have this problem.

  I just do a fresh install of the latest Sun JRE and then it worked fine.

• Dell Equallogic PS5000X NIC reference

  Hello

  does anyone have experience of SAN Dell Equallogic PS5000X?  I'll put in place at the moment and it seems there are 2 controllers for all of the 3 NIC (6 in total).  I find I cannot use 3 cards and 1 controller in Active mode and can not find a way to get the two controllers to work in unison and the two assets.

  I wanted to use 4 network cards for iSCSI traffic on a VLAN giving a rate 4 GB of storage but you can use 2 network cards, giving a throughput of 2 GB and 1 for management.

  Is this the only method available for this type of SAN?

  Any advice would be greatly appreciated.

  Andy

  Hey,.

  The PS is an active / standby. A controller is active. The other will be the shot if the first of all a problem. You have only a configuration to do.

  You configure 3 interfaces in the GUI. eth0, 1, 2.

  The second controller will use this interface when you need.

  You can dedicate a management port, but Dell recommends that you connect all of your ports to the ISCSI network.

  Hope this helps

  Please consider my response as 'useful' or 'proper' marking

• Cannot print. Reference Dell 944 communication usb port is not available. error check your firewall settings to ensure the printer communication is not blocked.

  Original title: unable to print. Reference Dell 944 communication usb port is not available.

  Message says 'check your firewall settings to ensure the printer communication is not blocked. Printer has worked faithfully until the problems started with the XP Home operating system. To cut a long story short ram upgraded to 2 GB, all unnecessary programs identified and technician Microsoft contacted to solve problems.  I was informed of problems caused by 3rd software party conflicts. Kaspersky was apparently the culpit. Dell Inspiron 32 now much faster but the printer will not work little matter what I do. I tried to reload with drivers & utility CD, drivers uninstalled & reinstalled on the site of all nothing is? Can someone help?

  DavidNicholsonXN,

  How to download and install drivers in the correct order

  also try to read...

  The owners of all-in-one printer Dell 944 thread (W7)

  Let the printer after Kaspersky

  Rick

• (Redirected) Reference Dell 1815n-photocopier/printer/fax(Error file format not supported trying to print from a USB flash drive stick)

  So I saved for different types of documents on a flashdrive (PDF, Word, Excel) and after having placed the flash stick drive in port on my Dell 1815n, an error pops up that States format not supported for files. I have formatted the USB stick, but cannot get anything to print. I tried 2 different flash drives to ensure that either has not been corrupted? Any help?

  Best of this post in the Forum of devices/printers, here:

  http://en.community.Dell.com/forums/3528.aspx

  Bev.

• Reference Dell 2150Cn-error code 016-302

  I have dell 2150cn. Error code 016-302

  I restarted the printer, removed cable eth printer.

  I can print from USB connection, but once I connect the printer to the network, printer spits out error 016-302 code.

  I've updated to firmware lasted, do not know what else to do

  Does anyone have any help?

  Thank you

  Hi Gravydog88,

  Please follow all instructions carefully and print test pages, as requested. Keep us informed of the results.

  Thanks & best regards,
  Babita S
  #iworkforDell
  To learn more about Dell Product Support, drivers & downloads, order & Dispatch status-> choose your region->
  AMERICAN customers ; Clients of the United Kingdom ; Visitors to the India . For video Dell technical support click on here

• Reference Dell pc with xp family. Restart to the logon screen

  Reference Dell pc with xp family. Restart to the logon screen. starts ok in safe mode. run msconfig and do that no change then do restart ok everything ok until the cold start, then hand it to restart?

  Peek into the registry to find clues.

  Disable the automatic restart in case of system error and see if you can capture a message of error checking bug (BSOD) with useful information.  Automatic restart in the event of system failure can be disabled in the F8 advanced boot menu, or you can turn it off in system properties.

  1. right click on my computer and select Properties.
  2 - Click on the Advanced tab, and then click on the Start button and recovery settings.
  3 clear the automatically restart box and OK your way out system properties.

  Start the computer in a Clean Boot State, if the computer starts successfully in a clean boot state, then one of your user programs most likely problems, look in the case of journal of indexes.

  How to configure Windows XP to start in a "clean boot" State
  John

• Reference Dell M1000e + aggregator MI/O port mapping

  Hi all

  I intend to install a new chassis Dell M1000e with Dell M/o aggregator. During the time of solution, I have a few questions about correspondences between the physical uplink with NDC blade ports ports. A Please check the config below and specify my queries?

  My hardware:

  • 1 x Dell M1000e
  • 2 x M i/o aggregator (A1 & A2)
  • 16 x M630 Blade (Qlogic 57840 S ANC four ports card)

  Reference DELL M/o aggregator:

  (reserved for Future use) module QSFP + 2 ports (Port No1:33 - 36 & No2:37 Port-40)

  I want to use these two modules for my blades 4-port Quad and the confusion I had, how to associate these 16 ports (8 ports of each module) to the server blade and the amount of bandwidth I will get by blade with redundancy.

  Module 4-port SFP + 10 GbE (Flexi-O of the Bay) (Port No.: 41-48)

  Module 4-port 2/4/8 Gb FC FlexIO (Flexi Bay 1) (Port No.: 49-56)

  FYI - I would like to install ESXi 6.0 on all blades

  Thank you!!

  Vinay

  Oriented server ports are configured automatically as part of the aggregation of links groups if the server is configured for the LACP Protocol. Static GAL is not supported.

  You will use the segregation network VLAN. A VLAN for network traffic and the other for the CF. Here are the commands to configure interfaces for different VLANS.

  Unidentified:

  Dell (conf) # tengigabit interface 0/16

  Dell(conf-if-te-0/16) # vlan unidentified 4

  Output Dell(conf-if-te-0/16) #.

  Tag:

  Dell (conf) # tengigabit interface 0/16

  The tag vlan Dell(conf-if-te-0/16) # 4

  Output Dell(conf-if-te-0/16) #.

  Traffic from servers will follow the path of the VLAN. For example, if an internal server, facing the port is set to VLAN 4, that traffic will be transmitted on the uplink port which has also set to VLAN 4.

  By default, all external ports are placed in a single whole LAG. However, you can change the configuration to support several shifts of uplink. Page 159 of guys configuration takes you step by step on setting up several shifts of uplink.

  The aggregator automatically configures to match the FCoE parameters used in the switches to which it connects through its uplink ports. FIP snooping is automatically configured on an aggregator. Automatically configured port channel (LAG 128) works CWF port mode. See page 86 for more information and examples of config.

  For redundancy, you could stack the units together. 241 page details the process of stacking.

  Page 54 of 102 of the Guide blade IO has one other diagram that details more internal server port mapping for each blade.

• Warnings of Dell EqualLogic SAN headquarters service

  Hello

  We receive these warnings on the Dell EqualLogic SAN headquarters service:

  • [ID: 3.23] ATTENTION: Network of members EquallogicMember1, eth0 Port, isn't reachable.  Unable to get network for Member performance data.
  • Condition has already generated an e-mail message. If the problem persists, additional messages will be sent approximately once every 6 hours.
  • [ID: 1.6] The EquallogicMember1 group has been added using address not WKA. Delete and add the group using a valid group IP address (192.168.1.2).
  • The EquallogicMember1 group has been added using address not WKA. Delete and add the group using a valid group IP address (192.168.1.2).
  • Condition has already generated an e-mail message. If the problem persists, additional messages will be sent approximately every 6 hours
  The Manager of EgualLogic we have IP 192.168.1.5 (it is an iSCSI network address):
  Group "EquallogicGroup1"------Configuration Group------General-General settings-IP address of group------192.168.1.5
  But on:
  Group "EquallogicGroup1"-members------EquallogicMember1------network-eth0-192.168.1.2
  Group "EquallogicGroup1"-members------EquallogicMember1------network------eth4------10.10.10.9 (role of management only).
  Could be linked and how to fix it?
  Thank you

  In the user interface, select the Member-> network.  Check the latest interface.   It should show to the management.  The verbage depends on the firmware version and table model

  Instructions on setting up lie in online via the UI and help.

  psonlinehelp.equallogic.com/.../About_dedicated_management_netwo.htm

• Reference Dell 6224 and 5448

  Hi team,

  I'm new dell switches - exposed to cisco switches. I am faced with new kinds of problems with these dell switches. Unable to provide a fix and fight for the last 5 days. Pls help me. Below is my script

  Two nw - 2.0 and 3.0 is required to be configured in VLAN, VLAN ID 2 and 3.

  VLAN 2 - 192.168.2.1

  VLAN 3 - 192.168.3.1

  N/W 2.0 and 3.0 N/W machinery will be shared 48-Port powerconnect switch 5448 DELL

  The routing part arrives at 6224 power connect - gateway for vlan 2 - 192.168.2.1 and bridge for VLANs 3 - 192.168.3.1

  The switch of two is ascending through fiber optic - spf port cable

  This is the configuration I did-

  5448 switch-

  database of VLAN

  VLAN 2, 3

  output

  interface vlan 2

  switchport access vlan 2

  GVRP enable

  Routing

  output

  interface vlan 3

  switchport access vlan 3

  GVRP enable

  Routing

  output

  interface ethernet 1/you/1

  switchport mode general

  VLAN allowed switchport General add 2.3

  GVRP enable

  output

  interface ethernet 1/g1

  switchport access vlan 2

  GVRP enable

  output

  interface ethernet 1/g2

  switchport access vlan 3

  GVRP enable

  output

  Uplink port is TE1 (Layer 2) to XG2 (Layer 3)

  Reference Dell 6224 can connect

  Configure the terminal

  interface vlan 2

  no downtime

  IP 192.168.2.1 255.255.255.0

  Routing

  output

  interface vlan 3

  no downtime

  address 192.168.3.1 IP 255.255.255.0

  Routing

  output

  interface ethernet 1/xg2

  switchport mode general

  VLAN allowed switchport General add 2.3

  GVRP enable

  Computer with 192.168.2.100 / 24 GW 192.168.2.1 connected to layer 2 switch g1 - vlan 2

  When I ping 192.168.2.1 - accessible United Nations host destination

  Even the wise

  Computer with 192.168.3.100 / 24 GW 192.168.3.1 connected to layer 2 switch g1 - vlan 3

  When I ping 192.168.3.1 - accessible United Nations host destination

  Any thing that has missed out in the configuration part / all bad entries. I'm not sure now how to treat this. Pls help me and it is an urgent task for me

  Thank you

  With multiple VLANs, you need to use the general/Trunk mode. With the help of the info we have I made a diagram to help show the location of the switches and parameters on them. Obviously things can be different, such as PVID, IP address, VLAN ID etc are all customizable to your needs. But the page layout modes and the port will remain the same.

  

  STP will not fill the VLAN on the other switches. It's probably the GVRP feature it refers. With such a short race, it is more practical to manually add the VLAN. At least for the initial Setup, then once everything works enable GVRP to accommodate future expansion of VLAN.

  Hope this helps some.