Reference Dell insipiron 3521 does not start

Similar Questions

• (Redirected) Dell Inspiron N5110 does not start

  Hi, my laptop Dell Inspiron N5110 is now 3 years old. I recently had a hard drive fail, then replaced by a new. Now the machine does not start. I have a boot disk in the DVD player that swirls, but gets no further. I get also is no longer the screen Dell displays (before the windows one). In fact, everything is empty. I tried to remove the power supply by battery pack and power holding down the button for 1 minute then re - again no difference. Is there anything else I can do or is the death machine?

  Thank you

  Daniel.

  Please repost this in the laptop computer forum for faster assistance.

  http://en.community.Dell.com/support-forums/laptop/

• Dell PowerEdge 2850 does not start on a CD of ESXi 3.5

  Hello...

  I have a Dell PowerEdge 2850, who does not start on a CD of VMware ESXi 3.5.  The server works very well with Windows 2000 server.  My first thought to solve this problem was the BIOS.  This is all what I've updated in what concerns the firmware on the box today.

  BIOS - A07

  Perc4e/Di - 5B2D, A19

  BMC Firmware - 1.83, A10

  Here are the latest versions of firmware available from Dell on this box.  The machine starts to start the machine.  But all I see is the first line of text of the CD which is the following:

  ISOLinux 3.63 2008-04-10 Copyright (C) 1994-2008 h. Peter Anvin

  My next thought was that there was something wrong with the ISO image that I downloaded.  I tested it on another machine; has worked like a champ.  Now, I read on a few different posts within the VMware communities that some people have had luck with this question and others did not.

  The inventory number of Dell on the machine is 6HDGS81

  Any advice would be greatly appreciated.

  Some of the Dell CD-ROM may be little flighty. I had hard time to install a CD earlier which worked perfectly well on another machine. I made another copy of the disc, this time burning the CD at a 4 x speed. The installation went perfectly fine afterwards.

• Dell XPS-8900 does not start

  Worked well to date, 01/01/2016 - Happy New Year, NO!

  Change power cable, use a different outlet (other items such as router and network printer can very well). Computer still does not start.

  When I plug it in the computer power light turns on light and then turns off (this seemed normal before). So if I push the power button computer does not start.

  I don't seem to get an orange light sequence of 2-1 after trying to turn it on - and continues. Maybe some sort of signal POST?

  I can turn the computer (not my first choice) after our journey ahead. But I'd rather get it upward and now running. Have work to do.

  Phil

  More information. I had four USB3 external drives attached, whose two propulsion and two disks Seagate Wireless - which is recharged through its USB port.

  Removing only the second Seagate drive allows the machine starts. So the question can be too much of a drain on the USB card current.

  Once started, the system seems to work very well with that wireless Seagate drive attached, and it restarts with it attached - just not boot from a condition of Shut Down.

  Not sure really, I understand that, but I can live with that.

  If someone seems something more insidious in this behavior, please notify; bought the XPS-8900 at COSTCO and still about 55 days return if it is defective!

  Phil

• Dell Precision T3500 does not start

  I have Dell T3500 Office, I pressed the Start button and the lamp on the Start button began to blink for a few seconds with a noise of power supply (SMPS/PSU) and 1 and 3 flashing and lights out. During this time I have observed that the power supply fan GET making small movements but does not turn the LED on the motherboard (orange) lights. I tried to start again and again, it does not work.

  Is this because the PSU become defective? or simply a RAM issue? I removed the RAM cleaned and then re inserted but it went past too to no avail. Can someone help me please to solve this?

  Flashing power button / stop Amber is bad food.

• Dell Dimension C521 does not start

  I have a Dell Dimension C521 desktop computer. When I try to start it, the fan turns on and is really hard, but the screen does not light. The power light on my computer lights up (green), but the 3 & 4 diagnostic lights flash repeatedly on the front of the computer. What is the cause? What can I do about it?

  NetFanatic123

  Hello Bev,

  The rest green power light on, no blinking, no beeps. I had no problem until last night after that I removed the hard drive and reinstalled.

  How can I remove the memory modules?

  Thanks :)

   

  NetFanatic123

  For the removal and reinstallation of the RAM, details are HERE NOTE from the ADMIN: broken link has been removed from this post by Dell >

  A hint: make sure that the modules are filled into the slots and the clips are in the notches.

  While the case is open, check that all the power cable and the data are correctly connected to the drive and the motherboard, by removing and reconnecting them.

  Why the hard disk has been deleted and reinstalled, was this HD replacement, or what?

  Bev.

• Dell Latitude E6400 does not start pressing the power instead button, I have to remove the battery.

  Original title: problem starting Latitude E6400 lappie

  Hi all

  When I start my dell latitude6400 is not start pressing the power instead button I have to remove the battery to the rear and place it again, and then the lappie starts... someone can help to...
  Thank you

  Hello

  1. what happens when you start the laptop, you receive no error message?

  2 have you made any changes to the computer before the show?

  I suggest to remove the battery and connect the laptop to AC power and then try to start the computer to see if the problem is with the battery.

  I suggest you to contact Dell support on the issue, as this can be a hardware problem.

  http://support.Dell.com/support/topics/global.aspx/support/DellCare/contact_us?c=us&l=en&s=DHS&CS=19

• Dell PowerEdge T320 does not start

  Hello

  Customers told Dell T320 server that no longer starts. He said that he tired to update firmware iDrac, but after restart server could not start. Server initializes the memory and starts initialization of iDrac, stays there for a few minutes, giving massage iDRAC initialization failed and restarts again and again. never of boots. I tried to remove all components PCIe and USB, no luck.  Please let me know how I can fix this problem

  Lapinas

  Now I get error swc0700 IDrac and life cycle control disabled.

  This error is caused by multiple restarts that lead to errors of IPMI. Update the firmware of the iDRAC.

  Reposition the controller and the ends of the cables connected to the controller. This device is installed on the 4 PCIe slot? Re-seat all PCIe devices and restart. Response to my e-mail with DSET report.

• Dell Dimension 4600 does not start after upgrading CPU

  Hello

  First of all, I tried to send this last night but received a message on my post approval by moderator? Not yet been approved but seen other people have posted with success more recently. Do not know what is happening.

  In any case, put his hand on a 3.4 Ghz HT P4 Northwood 512 Kb 800 Mhz FSB for £10 on Ebay to upgrade my mother enough old Dimension 4600 which has a 2.8 Ghz P4 512 KB 533 FSB inside... However, when I install it the computer does not light and shows just a light amber. The readers and fans still spin but there is no display. The computer works normally when I put the old one back in.

  I think somehow it is a power supply problem as the new processor uses 20w more energy than the old 2.8 Ghz one. Someone at - it ideas? Just trying to figure if I bought a bad CPU, so I can return.

  Thank you

  Andrew

  AV115

  Hello

  First of all, I tried to send this last night but received a message on my post approval by moderator? Not yet been approved but seen other people have posted with success more recently. Do not know what is happening.

  In any case, put his hand on a 3.4 Ghz HT P4 Northwood 512 Kb 800 Mhz FSB for £10 on Ebay to upgrade my mother enough old Dimension 4600 which has a 2.8 Ghz P4 512 KB 533 FSB inside... However, when I install it the computer does not light and shows just a light amber. The readers and fans still spin but there is no display. The computer works normally when I put the old one back in.

  I think somehow it is a power supply problem as the new processor uses 20w more energy than the old 2.8 Ghz one. Someone at - it ideas? Just trying to figure if I bought a bad CPU, so I can return.

  Thank you

  Andrew

  AV115

  Andrew,

  It is not a power supply problem, it's incompatible, or a bad processor problem.

  The first models of 4600 will take up to 3.0 GHz and models later, 3.2 GHz to 3.4 GHz, but this does not offer much of a sudden boost on the 3.0 GHz

  Motherboard Dell P/N F4491 will support up to 3.4 Ghz Northwood leaving Prescott

  Bev.

• Dell Studio 540MT does not start, green power light on, but the Start button / clear stop completely

  Looking for assistance

  Have a Dell Studio 540MT (purchased in 2009), worked great until 2 weeks ago.   After a temporary system failure would not start.    The power light itself is green fixed.   The power button on the front panel is completely released.

  I read a lot of messages and other information about a similar problem.   Therefore, I did following:

  1. unplug everything, press the power button / stop for 1 minute and retries.   without success

  2. replace the CMOS battery.  without success

  3A jumps the Green and black 20 supply connection wire pins to motherboard.  It started immediately food, fans and hard drive.   so I assumed that the PSU has been authorized.

  4 replace the motherboard with a new mobo.  Curiously, in a first time, there was no change, but after about 2 minutes, the power button was working and power system.   Everything worked so very well.   I had also completely cleaned all the dust in the chassis and radiator, fan and had applied the thermal paster as directed by Artic Silver.   I even turned off after hours of race and restarted system.  Restarted, he noted that it took a couple times by pressing the power button to make it work.   Then the 2nd day I shut down the system by a normal shutdown through Win 7 and let rest for about 10 hours.   When tried to start/turning the power on again, same problem as the original problem... at first, before light power button would show amber flashing when first pressed the power button / stop, then once I unplugged the power cord and let it sit for 1 hour, the light power button showed no light, completely and again no restarts.

  5. I ordered a new power button cord (new)... This could be the problem and replacement will fix?   Is this a known problem that power button can cause this kind of problem?

  6 or is a problem of power supply?   But you wonder why the green light of the PSU and works very well when jumping the Green and black wire on the connector 20 pin?     Before I go buy a new power supply to other suggestions?

  Is there a known issue with button / stop itself and/or PSU on Dell Studio 540 MTs?

  Yes, the front panel can cause failure to start in some models, although I don't specifically remember if the 540 has been affected by this problem. Please let me know if the replacement resolves the problem.

  ATX power supplies should work. Here are the standard components of the Dell desktop computers.

• Reference Dell A10 946 does not

  See the description in the "title area' above.

  My printer (Dell 946 A10) is not communicating with my command 'print '. I can copy, scan & Fax, but cannot print.

  Hi Lee,.
   
  1 you get an error message when tried to print?
   
  We recommend that you download and run Microsoft set to find and correct printing errors. To do this, visit the following link and click on the "Run now" button: http://support.microsoft.com/gp/printing_problems
   
  Visit this link for more information on "Solve printer problems":
  http://Windows.Microsoft.com/en-us/Windows-Vista/troubleshoot-printer-problems
   
  I hope this helps.
   
  Thank you
  Syed
  Answers from Microsoft supports the engineer.

• Dell XPS 8500 does not start after the interruption of system restore

  It was one thing to do, but I turned off my PC during the restoration of the system because he took time to complete the process.  The next day I couldn't boot into windows.  I tried the automatic repair feature, but it does not work.  I tried to repair windows using the orignal installation disk, but it does not work.  I tried to install Windows 8 all over again, but I got an error message - media pilot is missing.  I opened the box uninstall the RAM, videocard unplugged and both drives and reinstall, but without success.  I noticed that there is an orange/orange light on the motherboard.  I thought it was the hard drive at the beginning, but now I hope that this is not the motherboard.  Any help will be appreciated.

  RB

  You have damaged the image beyond repair.  You need to reinstall from scratch.  Windows to say that an optical drive driver is missing, bad copy of DVD-RW, DVD + R or DVD - R media that was not burned at 1 X 2 X or 4 X, so is not readable.  This is why USB Flash Drive 16 GB or more is recommended rather than the DVD player to the installation media.

  Why doesn't my CD or DVD drive?

  Troubleshoot installation of Windows 7 Service Pack 1

  A required CD/DVD drive device driver is missing
  A media computer driver needs is missing
  error message when you install Windows

  https://support.Microsoft.com/en-us/KB/2755139

  This problem occurs for the following reasons:

  The installation DVD is removed during the installation process.
  A bad quality DVD has been used to create the installation DVD.
  The speed at which the installation DVD is burnt was too fast.
  The DVD drive cannot read media.
  The ISO file is corrupted.

• Reference Dell V515w printer does not print second job

  I can print 1 post.  The second task remains in the queue until I do a restart.  How can I get my printer to print the second job without performing a reboot?

  I had the same problem and went to Microsoft forums and have tried many suggestions, I saw on the autumn 2013 Dell support site, IE 11 may be the problem

  uninstall IE 11 failed. Microsoft community Web site, it said to run from the admin command line

  ORFILES/p %WINDIR%\servicing\Packages/m Microsoft-Windows - Internet - Explorer * 11. * .mum /c "cmd /c echo uninstalling @fname package & start /w pkgmgr /up:@fname /norestart.

  got error messages, but it has worked and solved the problem

  Then, of course, a problem with interaction between IE 11 and some Dell printers. I asked the Coordinator of the Microsoft forum if we could report the problem to Microsoft. It would seem that Dell support needs to talk to Microsoft to resolve this problem and not just pointing the finger at the other.

• Reference Dell R310 Server Blade not start CD ROM [FRESH WINDOWS SETUP]

  Hello

  I have a Server Blade Dell R310. I created the virtual disk on a Raid Configuration, also I updated the BIOS boot.

  I PERC S100 when I checked on my configuration tab.

  The scenario is that I want to install a new / new copy of Windows 2008 R2 on this server, I have the dvd bootable. but when I put it on the drive it says "No Bootable Media found" something like that.

  Y at - it all the configurations that I missed? hoping to get answers from here.

  Kind regards!

  OK, let's back up a bit:

  Use the management tools of systems and Documentation (GDPS) instead of SBUU.  If you use SBUU with 2008R2, you should use the Driver Pack too... MUCH easier to use the GDPS, which has everything you need in there:

  FTP (you will need to copy/paste - forums do not like the FTP links):

  FTP://FTP.Dell.com/secure/FOLDER01538030M/1/OM_SMTD_730_A00.ISO

  Yes, you start on GDPS, follow the instructions, and then insert the 2008R2 media when prompted.

• Dell Inspiron N5110 does not start

  Hello!

  I went to dell [F12] startup options and ran the diags.

  It throws following error message upward:

  Error code: 2000-0145

  Validation: 45371

  MSG: Hard drive 0 s/N 5VEKQY27, self test has not completed.

  [HD bios is detected correctly].

  What should I do now?

  You will need to replace the hard drive - which, while a bit expensive component to replace, is not easy to access on this model.  You can watch the video below before you decide to replace it yourself - or do a workshop work for you.

  You will need a new 2.5 "7-9.5 mm laptop SATA hard drive (hybrid or or drive solid state drive).

  www.YouTube.com/watch