Dell XPS 8500 does not start after the interruption of system restore

Similar Questions

• Dell XPS 8500 does not start

  Hello!

  I can't from my Dell XPS 8500.  The Green POWER light turns on, but when I press the power on button flashes white then turns off. Then flashes white once again and turns off, and continues to do this.

  Also, it seems that something is you try to start on the inside.

  I have attached a simple video of his behavior.

  Thank you very much!

  cs_setInnerHtml ('video_f0261ded-ff62 - 45 d 7-aba5-48e70240498a', ");

  Hello Nice of you to hear. Seems to be a bad connection to one of the memory modules.
  These problems occur and nothing to worry about. Should it happen in the future give US a shout.
  It's the pleasure to serve you.

• XPS 8700 does not start after the upgrade memory RAM

  Dear members of the Forum.

  I have a XPS 8700 with the following specifications:

  Core i7 4770 k

  2 TB HARD DRIVE

  16 GB of Ram (4 x 4 GB)

  NVidia GTX 660 (1.5 GB)

  BIOS version A10 (later).

  RAM sticks in my current system are all Micron Tech (here) 4 GB DDR3 SDRAM PC3 12800 240pin 1.5V 1600 MT/s.

  I had two RAM modules of tech Micron (here) 8 GB DDR3 SDRAM PC3 12800 240pin 1.5V 1600 MT/s so that I can move on to a total of 24 GB.

  After the discussion here and here, I installed the modules in slots 1 & 2 (both white) so that the system is not able to start. Not even got the bios screen. I also tried 3 & 4 configuration (both black) I ran my computer with the two 8 GB sticks only, with the same unfortunate results.

  I also saw that it is a normal problem of compatibility problems between the types of ram, but I consider that this is not the case. In addition, bad positioning of the modules is not also the case because if I put my old ram glue the computer starts normally.

  I used tape you will static isolation.

  Is the problem, a problem of compatibility between my computer and the RAM modules?

  If the RAM is damaged does these effects (do not start)?

  How can I check if the RAM modules are damaged?

  What would be your suggestions?

  I thank very you much in advance!

  Mauricio

  Hmm, I'd say you two bad sticks of RAM.  If the system POST even with them, I would swap them if you can.  We know that the RAM slots work because you have 4 x 4 sticks without any problem and your computer can take up to 32 GB of RAM.  Your admission that you bought the right kind of RAM, voltage, and speed, etc., so that shouldn't be a problem.  I would say as bad RAM.  When you do not install, just check that you make pairs in each of the colored slots, for example. matching pairs in the slot of white and black.

• Pavilion dm4-1160us does not start after the failure of system recovery

  I have Windows 7 Home edition is installed. In my view, it is 64-bit.

  I get everything by initializing the error message is:

  "BOOTMGR is missing".

  Press Ctrl + Alt + Delete to restart»

  When running various tests (Tuneup, break-in, Start-up, hard drive) in I always get the same failure ID: M4PC2J-5KQ6N0-XD6V41-60VG03. The poduct ID is XH124UA #ABA.

  The case began after my computer froze and I forced the reboot.

  I guess that the hard drive is a gonner. Is this correct?

  Hi Mario,.

  Personally, I recommend to replace the hard drive yourself - it is a surprisingly simple process (and much cheaper).  A brief guide on this is detailed below.

  Your computer is listed as coming with a 500 GB hard drive, but you can also easily install a 750 GB HARD drive if you want a little more space - readers at the following links are examples that would be perfect for your laptop.

  Hard drive 500 GB

  750 GB hard drive.

  The procedure to replace the hard drive begins on Page 61 of your & Maintenance Guide.

  Once this is done, simply use your recovery media to reinstall the operating system on the new drive - this is described in the document of HP here.

  If you do not have your recovery media, let me know because there is another option, you can use it as long as you can clearly read the activation of 25-character product key on your label COST.

  Best regards

  DP - K

• Windows XP does not start after the interruption of the power supply

  Power was cut while the computer is running, now when you try to start the computer, it goes to black screen with options to start in safe mode, start in SafeMode with network, last good configuration and boot normally.

  I tried all the choices and put right back on the same screen. How to make the computer to boot normally without losing all my personal data of staored on the hard drive?

  Be careful to perform a repair installation.  If you have upgraded Internet Explorer (IE7 or IE8, for example) must be uninstalled before running the repair facility:

  "How to perform a Windows XP repair installation, if a later version of Internet Explorer is installed"
    <>http://support.Microsoft.com/kb/917964 >

  Your first priority should be to save your existing files.  My preferred method is to create a free Knoppix (Linux Live) boot CD and boot your machine from the CD.  This should give you full access to your hard drive and allows you to copy your files to an external USB drive or a network drive.  Afterwards, you may need to reinstall Windows, either from a recovery partition or your recovery CD.  Creating a Knoppix disk is as simple as downloading an .iso file and your function "Burn Image" program of CD burning to create a CD.

  Knoppix: http://www.knopper.net/knoppix/index-en.html >

  HTH,
  JW

• computer does not start after the Windows XP logo window

  Windows xp home edition
  service pack 2
  Dell inspiron 1501

  1. computer does not start after the Windows XP logo window
  2 works well in safe mode, even connect to the external monitor
  3. I reinstalled xp many times, problem stil exist.

  All the answers?

  Hi dhanushm,

  1. What happens after the Windows logo screen?
  2. You receive an error message?
  3. You have security software installed on the computer?
  4. Have you performed an installation clean Windows XP and even after that this problem exists?

  Method 1

  As the computer starts up fine in safe mode there is a possibility that some third-party programs installed on the computer is the origin of the problem.

  I suggest that you configure the computer in a clean boot state and check if it helps.

  To help resolve the error and other messages, you can start Windows XP by using a minimal set of drivers and startup programs. This type of boot is known as a "clean boot". A clean boot helps eliminate software conflicts.

  See section to learn more about how to clean boot.

  How to configure Windows XP to start in a "clean boot" State

  http://support.Microsoft.com/kb/310353

  Reset the computer to start as usual

  When you are finished troubleshooting, follow these steps to reset the computer to start as usual:

  1. Click Start , and then click run.
  2. Type msconfig , and then click OK.
     The System Configuration utility dialog box appears.
  3. Click the general tab, click Normal Startup - load all device drivers and services , and then click OK.
  4. When you are prompted, click restart to restart the computer.

  Method 2

  If fails it above step can refer to the article below and try the steps mentioned, check if it helps.

  After the Windows Logo appears or after you log in to Windows, a Windows XP computer cannot display the wallpaper, a black screen or a blue screen

  http://support.Microsoft.com/kb/318027

• Two iMacs does not start after the 10.11.4 update.

  Two iMacs does not start after the 10.11.4 update.  Progress bar starts moving and then text appears on the black screen saying unexpected sigkill to launchd.  He then gets stuck in a loop trying to start.  Tried to reset the SMC and LANDAU.  Without success.  Started in recovery mode and ran disk utility.  Discs said OK.  Chose to reinstall OS X from the list of options in the recovery mode (assuming it would be 10.11.4).)  Installation is finished but still once does not start.  Reinstalled on 10.11.0 successfully from a USB key and downloaded the 10.11.4 combo updater.  Installation seems to work, but once again, the macs will not start.  Same 'unexpected launchd sigkill' error.  A mac is now back working properly with 10.11.3 the other will be shortly.  Is there a problem with the accession?  Our COMPUTER support use Munki to get updates from one day to the next.  Fortunately, we were able to stop it before the other 20 or if Mac had the same problem.

  More information: two bricks iMacs were late 2013 models.  A 21 "and a 27.  We have just updated a test iMac which was a late model 2012 using the 10.11.4 combo updater.

• ITunes does not start after the installation of Windows 10

  ITunes does not start after the installation of Windows 10, 1511 version (OS Build 10586.164). ITunes version 12.3.2.35, 6 GB RAM, Intel i3 @3.3 GHz. Itunes and Ipodserver module will run by Manager jobs, but Itunes does not open. iTunes starts in SafeMode as explained in the link below (hold SHIFT and control on your keyboard while you open iTunes).

  Fix unexpectedly closes or problems of launch in iTunes for Windows - Apple Support

  Solution, according to this link, is:

  If the problem does not occur in Mode safe, remove any third party plug-ins iTunes: solving problems with third party plug-ins - Support Apple iTunes but the link has been archived, and I can't find any plug-ins installed iTunes. Any other ideas?

  For general advice, see troubleshooting problems with iTunes for Windows updates.

  The steps described in the second case are a guide to remove everything related to iTunes and then rebuild what is often a good starting point, unless the symptoms indicate a more specific approach.

  Review the other boxes and other support documents list to the bottom of the page, in case one of them applies.

  More information area has direct links with the current and recent buildings if you have problems to download, must revert to an older version or want to try the version of iTunes for Windows (64-bit-for old video cards) as a workaround for problems with installation or operation, or compatibility with QuickTime software or a third party.

  Backups of your library and device should be affected by these measures but there are links to backup and recovery advice there.

  TT2

• Computer does not start after the screen of the bios, Compaq Presario SR1023WM

  Ok. Trying to fix a friend's computer and seem to have met a strange barrier.

  Problem: The computer does not start after the bios screen.

  Details: When you turn on the computer, the compaq logo with intel inside is and has the < F1 Setup > and < F10 System Recovery > options listed as well.  And that's it as far as the computer becomes.  After that the computer just locked up, no work of buttons on the keyboard lights keyboard ect ect.  I tried the puree on the F1 key, as soon as I turn on the computer and I can handle so he can say * entering setup * but it freezes again after this point.  I already tried to eliminate the possible sources of the problem, removed all expansion cards, HDD and Dvd Rom module only disconnected, only memory (256 MB ddr 2700), power, vga and keyboard connected.  Ive also used the jumper on the motherboard to clear the cmos, hoping that would solve the problem without success.  I tried using a different memory stick and different memory as well...  Tried to use both a ps2 and a usb keyboard... Ive even tried pulling the rider for the protection of the bios password (even if she did not have a password on it, just try everything I can think of).

  The installed bios version is 3.1, and that's all that I know on the computer at this point, except that the website tells me to him.

  http://h10025.www1.HP.com/ewfrf/wc/product?product=411354 & LC = on & CC = US & DLC = in & Submit.y = 5 & Submit.x = 3 & lang = to & CC = US <-link to the Web page for the model #.

  I'm basically at a loss on this one, so if someone feels scroll line-by-line of their brains on this one, I'd be very happy.

  I have a pretty strong understanding of computer repair, so feel free to give me something to try.

  If you need more information out of me, let me know as well.

  Try to clear the CMOS again but this time remove CMOS battery and hold the power button on a few seconds. Replace the battery, then try to start back to the top.

  At the back of the pc is the condition of the PSU led green or flashing?

• Z600: computer does not start after the installation of the 5 TB SATA drive

  My z600 refurbished does not start after the installation of a SATA of Toshiba 5 to disk.  After removing the drive, the computer starts.  I have my computer too old to handle a 5 TB drive, I something wrong or is the DOA drive?

  Thanks for the info.  I added the GPT to my search and discovered what had to be done in disk management.  Here is a page with step by step instructions and photos.  http://www.howtogeek.com/193669/whats-the-difference-between-GPT-and-MBR-when-partitioning-a-drive/

• XP does not start after the installation of avira. Blue screen: STOP: 0 x 00000024 (0 x 00190203, 0 x 87174270, 0xc0000102, 0x00000000)

  Original title: xp does not start after the installation of avira

  I have a HP Slimline s7410
  XP Home Edition SP3
  I had Norton free with Comcast, but since I have no more Comcast became Norton expired. So I uninstalled Norton and installed the free version of Avira, he scanned the computer and it was clean. I went to reboot and now it does not start.
  I have a cd/dvd drive of work.
  I don't have an XP bootable installation CD

  My system worked well until: I installed the free version of Avira

  Whenever I select one on the XP advanced options options menu start, it goes into a boot loop.
  I turn off the auto reboot system failure although it seems only work once, as the next time he's trying to start up it goes into the boot loop.

  Here's what my BSOD looks like:

  Disable or uninstall any anti-virus, disk defragmentation or backup utilities. Check the configuration of your hard drive and check the updated drivers. Run CHKDSK /F to check for hard drive corruption, and then restart your computer.

  Technical information:
  STOP: 0 X 00000024 (0 X 00190203, 0 X 87174270, 0XC0000102, 0X00000000)

  Any help is greatly appreciated! :)

  My first suggestion is to do a system restore at this time point.

  second suggestion is to keep your external drive connected to the pc at all times.  only detach when necessary.   of course, it would be better to install a second hard drive in the computer instead.   in any case, keep your personal files out of the system disk is a wise thing to do.   You can also download and store files for free on the Microsoft Skydrive site.

  third suggestion is to keep your system set upward through executing a check disk and Defrag at least once a month.   Basically, you can open the Explorer and right-click on the drive letter.  then select Properties, and on the Tools tab, you will have the opportunity to run the disk check.  then reboot and do a Defrag.   where this disk check fails, then you will need to run it to the drive via a bootable cd prompt.

  Interestingly, I don't know if the bootable cd that you made you allows to run the disk check.

  so my suggestion is to do a series of tests using your cd bootable your computer works.  see if you can actually run a chkdsk/r at the moment with them.    If Yes, then if your constant worries are having bad sectors on the hard disk, chkdsk/r will identify and mark so windows will jump on them.    in any case, see if your boot at the moment media can run a check disk at all, and let me know.

  fifth proposal is to install "microsoft security essentials" like your anti virus program.  even if you have run ubantu, it is not likely to have been an infected copy.   anti - are most critical virus for windows and not not so much for ubantu or linux is because windows is a system of world class operations.    the people who make the virus deliberately their engineer for the windows operating system.   If, however, ubantu and linux have been just as popular as Windows, virus engineers would make infections for the o.s. too.     Although they no doubt, attacks are more frequent for the windows os.

• computer does not start after the installation of vista updates.

  computer does not start after the installation of vista updates. Startup Repair is also not working. event name: Startup Repair v2, prob GIS. 1: automatic failover, prob GIS 2: 6.0.6000.16386.6.0.6001.1800, prob 3:6, prob prob 5 and 6 GIS GIS sig, 4:720907: corrupt file, prob GIS 7: 3221226021, 8:3, prob GIS GIS prob 9: repair wrp, prob GIS 10; 2, 0 s version: 6.0.6000.2.0.0.256.1. In addition, none of these advanced recovery options seem to work.

  Hello

  Try the steps suggested by David Y post dated November 2, 2010 in the link given below and check if that helps.

  http://social.answers.Microsoft.com/forums/en-us/w7repair/thread/a6071159-db22-4076-b5d8-31f446dbdf32

  Hope that information was useful

• BlackBerry Z10 my BB Z10 does not start after the no shutdown reason cannot go home screan

  Dear expert

  pls help my problem

  My BB Z10 does not start after the no shutdown reason cannot go home screan

  How can I save my data and contact if I reload / back up the operating system how ever my phone cannot start and go home screan

  Thank you...

  Dear expert

  Thanks for your reply, but recognized link bb cant he showed a black berries knowledge so the transferdata button is impossible / cannot click. so I can't back up my files and data if I reloaded the OS. are there\s any idea/way of backing up my files if my phne was frozen?

  Thank you

• Does not start after the upgrade to 1.5.

  Does not start after the upgrade to 1.5.  "EdgeAnimate.exe - not found entry Point? -Point procedure entry GetGestureInfo is not found in USER32.dll dynamic link library. »

  All ideas

  No problems in the past with edge since September 2012.

  =============

  Laptop HP Pavilion dv7-2185dx

  Dv7-2185dx product name

  #ABA product number NV023UA

  Microprocessor 2.00 Ghz Intel Centrino 2 Processor Intel Core 2 Quad Q9000 processor technology

  The microprocessor Cache L2 6 MB Cache memory

  6144 MB of memory

  Memory Max 8192MB

  Graphic ATI Mobility Radeon HD 4650 (M96)

  Video memory up to 2815 MB (1024 MB dedicated)

  500 GB (5400 RPM) hard drive

  Multimedia drive LightScribe SuperMulti 8 X DVD±R/RW with Support Double layer

  17.3 "diagonal HD + LED display high-definition HP BrightView Widescreen Display (1600 x 900)

  Fax/Modem high speed 56 k modem

  Network integrated 10/100/1000 Gigabit Ethernet LAN adapter

  Wireless Connectivity Intel WiFi Link 5100AGN

  The Altec Lansing SRS Premium Sound technology with subwoofer

  101 keyboard compatible with the keyboard keys full size numeric keypad with integrated

  Pointing device touch pad with On / Off button and dedicated vertical scroll up/down pad

  PC Card Slots 1 Slot ExpressCard/54 (also supports ExpressCard/34)

  External ports

  5-in-1 Integrated Digital Media Reader for cards Secure Digital, MultiMedia Card, Memory Stick, Memory Stick Pro, or xD Picture Card

  4 universal Serial Bus (USB) 2.0, 4th port shared with eSATA

  2 headphone

  1 microphone input

  HDMI

  1 VGA (15-pin)

  eSATA + USB 2.0

  1 RJ-11 (modem)

  1 RJ - 45 (LAN)

  expansion port for computer 1 cell 3

  1 IEEE 1394

  irewire (4 pin)

  1 consumer IR (remote receiver)

  Other devices HP Webcam with integrated digital microphone

  Dimensions 16.2 "(W) x 10.9" (D) x 1.37 "(min H) / 1.70" (maximum H)

  Weight lbs 7,74

  Housing for Kensington MicroSaver Security lock

  Turn on the password

  Accepts 3rd party locking safety devices

  Software

  Operating system:

  Genuine Windows Vista Home Premium 64-bit with Service Pack 1

  
  

  Hi, people.

  I was able to reproduce the problem here, so the good news is that you're not imagining things.  We are looking in the options right now for you guys, and I will contact you individually by private message to start again at the top.  This being said, please note that our techniques, Vista is an operating system that is not supported, and our team is not stable time on this platform.  We will do the best we can and we will keep you guys, update as to what status is.

  Thank you

  -Elaine

• T400 does not start after the first display screen

  What is going on? I have wss to work today and my computer shut down due to the low batt. I got home and plugged in and waited a few minutes and turned on. When I checked swipe my fingerprint, all that I saw the first startup screen told me I want to interrupt normal off set up that I can close the button think vantage. It is stuck there. I can activate it on and but it does not start after that screen. What can I do? I am in the middle of the drafting of the report and cannot access my docs!

  I looked the problem and found that have been in contact with the usb pins! Yay the prob is fixed!