Reference Dell R710 always detected memory guest VM in 95%

Similar Questions

• Reference Dell R710 - Configuration of memory

  Hi all

  I'm sure I'm missing something, but I read the two technical papers about memory configuration in the Dell R710.

  I have a server that currently has 48GB stated as follows

  A1 - 4 GB

  A4 - 4 GB

  A2 - 4 GB

  A5 - 4 GB

  A3 - 4 GB

  A6 - 4 GB

  (It then returned on the b-side)

  According to the BIOS it's set to "optimized."

  Now I have sticks of 2x16GB I wanted to install, the only way that I could operate without the whine of BIOS was to install as follows:

  A2 - 16 GB

  A5 - 4 GB

  A8 - 4 GB

  (Duplicated on b-side)

  Giving 72 GB.

  As I read the manual, I should be able to mix the sizes of memory for "optimized" as long I have spend from A1 to A9 and so I have an another 6x4Go sticks left, I want to install.

  My logic is that I can fill with A1 to A9, mixing the 16 GB, however when I try I get the error on the A1/A2/A3 needing to be the same?

  Am I missing something simple? I am unable to make changes in the BIOS, the memory is all of the same type (bought from Dell)

  Rob_991,

  The question that you are running in is due to the R710 need 3 memory channels to match.  Each game nine media is organized in three channels with three supports memory per channel. As shown below, each processor has 3 channels of memory, allowing only a single channel to the need to match, or filled.  So, with only having a couple of 16 GB DIMMs, you are only able to fill a channel on each side. What I would say is the addition of a couple more 16 GB DIMMS fill A1, A2, B1, B2 with them, and then place the 4 GB in A4, A5, A7, A8, as well as B4, B5, B7 and B8. This gives you two channels on each side, as well as 96 GB of memory.

  

  Let me know if this helps answer your question.

• Reference Dell R710, Dell and VMware VAAI MD3200

  Hi guys, we have 3 x Dell R710 hosts running VMware ESXi hypervisor v5.1. Our SAN is via Dell MD3200 Direct attached storage. We have activated the option of High Performance. My question is about VMware VAAI. In particular, the recommendation of VMware: http://kb.vmware.com/selfservice/microsites/search.do?language=en_US&cmd=displayKC&externalId=1033665 it says: "For more information on support VAAI in a particular storage group or required firmware levels, contact the storage array provider." So I'm wondering: is VAAI supported (or not) with the MD3200... and otherwise: should I be deactivation of VAAI settings as recommended by VMware? What are the potential implications for the performance of deactivation of VAAI... or support DO NOT turn it off? Thank you, Steve

  Indeed, you are using a fairly old firmware. The most recent is 07.84.53.60.

  To be able to upgrade to this version, you will need a version quite familiar of the MDSM. I would say to download 4.1.2.29 or later, which is 5.0.0.70. All servers Windows and Linux (not VMware or XenServer) server that manage and/or are connected via iSCSI SAN should have their MDSM, updated software before upgrade you the firmware on the raid on the SAN controller.

  RAID controller firmware: www.dell.com/.../powervault-md3200

  Latest resources DVD (5.0.0.70): www.dell.com/.../powervault-md3200

• Reference DELL R710 con disco rotto [GRO]

  Buongiorno, ho a server DELL R710 fuori co.

  HO a disco rotto.

  The error e he following:

  3 E1810 hard drive fault. Review & clear SALT

  MI servirebbe una offer by uno in sostituzione.

  Stiamo contattando by mail

  Saluti

• Reference Dell dock always shows an error at the beginning upward

  OT: Dell Dock.

  Dell Dock always shows an error at the beginning upward. Tried everything to remove it, but after three days, it always works on the removal of the transformation. What should I do now? I have a Dell Inspiron 545 s w/Windows 7

  Never mind. I'm tired of messing around with it. I disabled in the Startup tab "Yes I was" trying to delete, but it's not worth the hassle. Sorry for taking your time. At least I don't have to watch it at startup

• Reference Dell r710 upgrade to the idrac-7.

  Hello

  I have a few with idrac6 express dell r710.

  I want to upgrade to version business to use the kvm console.

  I know who to buy Ent idrac6 material to replace.

  But I want to upgrate to business idrac7 instead off idrac6 Ent.

  Is able to upgrade to idrac7 Ent or just Ent r710 idrac6?

  Please advice!

  Thank you.

  anhhuyla @.

  Anhhuyla,

  The R710 will support not using the iDrac 7, as is logical is incorporated into the Gen 12 systems themselves. To improve the iDrac6 at the enterprise level, you must add the Works Council (part number K869T or J675T) seen below.

  

  This will allow the use of the console remotely.

  Let me know if it helps.

• Reference Dell R710 enable HyperThreading on vSphere 4.1

  Hi all experts VM.

  I just buy Dell R710 server and installed Vmware ESX 4.1 on it.

  vmware configuration, I found that the "HyperThreading" does not.

  but I check the BIOS, it is already active.

  It is all set up on BIOS, I missed?

  attach with the show of the "HyperThreading" display not active on client vSpherer.

  Take a look at Intel® Xeon® Processor E5506

  Intel® Hyper-Threading technology no.

• Reference Dell R710 - ESX5.1 Server Admin 7.4 storage management alerts

  Greetings, I've been deployment OMSA 7.4 VIB to my Dell ESX5.1 host using successfully manage the update. However, all of my Dell R710s servers) report a warning in the Console Essentials OpenManage under the information Section of Agent software for the following: - Server (storage management) administrator - VMware ESXi 5.1.0 build-1065491 no further information is provided in addition to the version of the agent, the description, and manufacturing. Also, under this article the iDRAC6 shows as a "?" but the version of the agent and the description as well the listing agent. This could be linked to the fact that, under the CARS, section reports on RAC connection state as OFF. Step additional needed to get these warnings are resolved? See you soon

  You must configure two separate groups, I have one of MGMT (iDRAC) and another for the hosts, both being discovered using WS - MAN, because as you say they have different passwords, our names are the same.

  I hope this might set you on the right track.

• Reference Dell 2824 / Ubiquiti UniFI / label Guest WIFI VLAN

  Hello

  I have a PowerConnect 2824 and two Ubiquiti UniFI APs which each is connected to a port on the 2824.

  UniFi access points create wireless networks and share among all radio configuration. These two APs publish two SSID, a protégé of personnel, another network wireless wireless network not protected for the guests. I have the ability to mark every wireless network that I want to.

  I want to use a VLAN to push traffic via the Dell switch on a DMZ port in our firewall.

  My original idea was to:

  1 tag the comments with 11 wireless network VLAN.

  2. let the unlabeled personal wireless network.

  3. set the trunks on the two ports that puts an end to the APs to allow marked and 11.

  4. Add an additional port on the 2824 11 membership only.

  5 connect the 11 only port to port my firewall DMZ.

  Here are my questions:

  1. a trunk port enable both unlabeled and package ID?

  2. If so, can I specify a port DROP packets not marked? (I want to prevent things not tagged to reach the DMZ port on the firewall).

  3 - does anyone see a flaw in my game to the top?

  Thank you

  m

  Yes, they should be able to achieve anything on the vlan 1. The personal wireless packets should come in unmarked and vlan 1 being without a label, that is where the packages will remain.

  2 comments wireless packages will come in VLAN tagged on 11 and be able to access what in the VLAN 11, g16, could probably leave g16 tagged VLAN 11 If your firewall can read tags VLAN

  Your installer should work fine. VLAN 11 only have access to the dmz on the firewall port.

• Reference Dell R710 single CPU

  Hello team, we have R710 with single processor with populated 9 dims with 8 GB of memory.

  We have now 6 x 16 GB memory to improve memory, what is the best procedure to mix memory to fill the 3 slots with 8 GB of memory?

  Is it still feasible?

  StorageJohn,

  To maximize the amount of memory used, I would put the 6 16 GB DIMMS in slots A1, A2, A3, A4, A5 and A6. After that, then place a module dimm 8 GB in the location of the A7, A8 and A9. This is to maintain the requirements of the memory channels. See below.

  

  Let me know if it helps.

• Reference DELL e R510 upgraded memoria RAM [MS]

  Buongiorno,

  need di fare one set at level dei miei Server DELL R510.

  Sul sito dell trovo:

  SOLUZIONE 1

  Modulo di memoria sostitutivo certificato Dell 16 GB by some sistemi Dell - 2Rx4 RDIMMS LV for a 1600 MHz ECC

  Number di parte Winery

  SNP20D6FC / 16G

  Number di parte Dell

  A6994465
  a 165 euro

  e

  SOLUZIONE 2

  Modulo di memoria sostitutivo certificato Dell 16 GB by some Dell - 2Rx4 RDIMMS sistemi a LV DDR3 - 1333 MHz (require Westmere-EX (Intel Xeon E7) CPU-PowerEdge R810, R910, M910)

  Number di parte Winery

  SNPMGY5TC / 16G

  Number di parte Dell

  A6996789

  a 190 euro

  Qual'e the migliore Soluzione per me? Come posso verificare is both sound much compatibility?

   

  Supporto Dell

  Buongiorno,

  the memoirs da lei indicates sono perfettamente con compatibility it sistema reported

  OK, my che differenze, sono tra una e l'altra? Quella che costa di piu e piu veloce ha diverse prestazioni? o no no vale la Peña

  Supporto Dell

  , unica cosa, the memoirs currently has bordo 2 x 2 GB vanno estratte prima di installare the nuove.

  perch, so is diverse di memoirs? Ed incpmpatibili tr aloro?

  If a se, posso, having a disposizione della stessa series, installarle server other server knew an altro, Così da a rrivar a 8 GB knew quello?

  Supporto Dell

  
  Speaking saluti

  Manual

  e possibile avere un offerta da referred to dell by the scope ed sommergibili delle memoirs?

• Reference Dell r710 vmotion questions

  Salvation communities,.

  Have a 4.1 esx cluster with some esxi4.1 hosts u2. I have a question were can I vmotion between esx in the cluster hosts, but the esxi hosts don't vmotion esx 4.1 guests.

  I get an error message saying that the CPU is different even if they are not.

  Any help appreciated

  Hi Aneetu,

  I did a check it on one of the clusters we manage here and are running the r710 - different BIOS can cause this kind of problem so definitely check the revision levels

• Reference Dell R710 - Perc 6 / disc matrix (support 4 TB?), I supported

  Hi all

  Since then, we want to upgrade the hard drive 2 TB (3.5 inches) for a large as 3/4 to.
  Is there information on the matrix of disc official supported of PERC 6 / i?

  We use Seagate 2 TB 72kRPM (bought from Dell) on our R710 servers. If the PERC 6 / I can't stand 3 to/4 TB disk. Is it possible to order the H700 support 4 TB drive adapter?

  We have installed the latest firmware /bios,
  -Perc 6/i: 6.3.3 - 0002, A-00
  -System BIOS: 6.4.0

  Thank you and best regards,
  Caleb Wong

  PERC 6 does not support disks larger than 2 TB. The H700 is supported in the R710 and supports disks larger than 2 TB. I would not, however, use desktop or NAS drives.

• Reference Dell r710 12core 32 GB super slow with sql and need help exch2010

  Hi all and thanks in advance.

  I have a new r710 which has a great for a few months then it has slowly degraded until now, it's an analysis on all the vm, I can't tell which one is it slows down because all the performance counters show a lot of place in all categories. I've been doing the reconnection to the datastore2 and datastore1, then I get a restored connection. I moved the Exchange 2010 vm to the datastore3 that does not have errors, but it is still slow. I wonder if I should move all the vm off the other two data stores and delete, and rescan the esxi for storage and back as data 1 and 2 stores. I have esxi 4.0 not improved update2. and there an esxi license and there 6 installation of drives western digital black 1 TB in raid1 3 - then I have every configuration of raid as a logical drive which is then turned into a data store.

  I don't know if the downturn is the hardware or a virtual machine is pulling them down - I'll start out them one by one to test tonight, but the advice or opinions are welcome.

  I don't know what your storage looks like initially but I would recommend HAVE TO go with update 2 - we had all sorts of problems with particular storage when you use storage VSA as the left hand.  Update 2 provided some great improvements to the vmkernel regarding VMFS.

  You can also publish newspapers vmkernel of any of the host in question and we can take a loo at it.

  Seriously, update your esx/esxi servers is always a good practice when you have weird problems.

  See you soon,.

  Chad King

  VCP-410. Server +.

  Twitter: http://twitter.com/cwjking

  If you find this or any other answer useful please consider awarding points marking the answer correct or useful

• Reference Dell R710 does not start after power failure

  Hello, I tried to find answers on the forum but nothing so far

  I have this R710 at home that I use as a media server, it was working fine before a power outage the other night (no I don't have a UPS :-(

  When the power returned, I noticed one of lighting power supply has been turned off, so I took it out of the unit, but the unit still won't turn.

  I still have a so-called good food because the small green LED on the motherboard lights, and I can access the iDRAC, this feature, I didn't before the net Searchin' for answers, I'm kind of a novice with the servers.

  When I access the iDRAC, on the power supply page, I see nothing, no power supply listed.

  Is it possible that a diet might be "half bad", enough to work the emergency circuits but not the power outlet?

  Symptoms:

  Camera lights.

  Can access the functions of the Idrac, but doesn't do anything if I try to activate it via the tasks "quick launch".

  Power supplies are not visible on the pages of the Idrac.

  Display before work.

  Server was very well just before a power failure which took one of the PSU

  The remaining 870 PSU has the green light on, and the fan works for 2 seconds every time I cut the power it.

  Thanks for any help.

  OK, well... no answers.

  I found a place locally that sold a diet so I arrived with my server, I told them I would buy the power supply that I confirm that the fault was in fact the power supply.

  Well, you know, the unit started correctly with the new power supply, now in IDRAC, I see both power supplies but on that faulty, he reads "present, entry lost.

  So the answer is YES, a power supply may be defective, even if the green light is on.