Similar Questions

• 6008 USB channel power for specific times

  Hello

  I am new to Labview, so I don't know if it's easy or hard to do.

  I have an attached VI who writes exits Digital 12-channel.

  What I´d wants to be able to write each channel for a specified time (avoiding the is fine - it doesn´t have to be super accurate, but he needs to turn off automatically after a certain time).

  For example:

  When I click, channel 1, I want him to be for 1 second, then turn automatically cut and wait for the next command.

  When I click, channel 2, I want it turn on for 0.5 seconds, before turning automatically turn off and wait for the next command.

  When I click, channel 3, I want him to be for 5 seconds, then turn automatically cut and wait for the next command.

  etc.

  So when I click Run, I could click on channel 1, wait a few seconds, channel 1 still once, wait a minute, then channel 3, wait 10 minutes, then channel 2, etc, in any order.

  Is how easy it to do? Is this possible?

  Thanks in advance for any advice.

  Jon

  Hi Jon,

  If you want to set the time separately, my guess is it would be easier for you to create the channels separately. It's more manual work, but I think it's better to come up with an algorithm of time-supervision to all channels at once.

  To trigger the output, I think that it is better to share entries, then perhaps it would be good to get out them of the matrix as well.

  In a loop, you can check the value of the button and then just write 1 to the port, wait for the timeout with time delay vi, then wrtie 0 again.

  If you create tasks separately and do not merge error, the process for each channel will work in parallel, so a delay will not affect the actions of the other channel.

  Kind regards

  Mariana.

  

• Time for specific dept record display by adding 10 minutes

  Hello
  

  Oracle Database 11g Enterprise Edition Release 11.2.0.1.0 - 64bit Production
  With the Partitioning, OLAP, Data Mining and Real Application Testing options
  /****************************************************************************/
  
  create table dept(
  dept_id number(14) primary key,
  c_id number(14) constraint dept_fk references centers(c_id) NOT NULL,
  deptName varchar2(50)
  );
  
  create sequence dept_seq
  start with 1 increment by 1;
  
  create or replace trigger dept_trig
  before insert on dept
  referencing new as new
  for each row
  begin
  select dept_seq.nextval into :new.dept_id from dual;
  end;
  /
  
  create table shiftManager(
  s_id number(9) primary key,
  dept_id number(14) constraint shiftManager_fk references dept(dept_id) NOT NULL,
  title varchar2(110), /**e.g. Morning, After noon, Evening **/
  startTime date,
  endTime date
  );
  
  create sequence shiftManager_seq
  start with 1 increment by 1;
  
  create or replace trigger shiftManager_trig
  before insert on shiftManager
  referencing new as new
  for each row
  begin
  select shiftManager_seq.nextval into :new.s_id from dual;
  end;
  /
  
  select to_char(startTime,'HH24:MI'),to_char(endTime,'HH24:MI')
  from shiftManager where dept_id=1 order by startTime asc;

  I want to choose startTime adding 10 minutes to the end for dept_id specific for example time
  
  Dept1
  =====
  startTime = 09:00 and 14:00 = endTime
  
  POWER required:
  ================
  09:10
  09:20
  09:30
  09:40
  09:50
  10:00
  ..
  ..
  ..
  ..
  ..
  13:40
  13:50
  14:00
  
  Thank you in anticipation
  
  Best regards

  Raakh wrote:

  I am not able to understand especially startTime + (level - 1) / 24 / 6<= endtime="" +="" (600="" -="" 1)="" 600="">

  Oracle date arithmetic unit is day. So 1 / 24 represents 1 hour and 24 1/6 represents 10 minutes. You start by startTime and continue to add 10 min and startTime + (level - 1) / 24 / 6 impeccable (level starts from 1). Now we must stop when meet us or exceed the end time for the first time. Therefore, we can add add 9 min 59 s to endDate and use it as the end. And (600 - 1) 3600 / 24 represents 9 min 59 sec.

  In fact, we can simplify and use the following logic: difference between current 10 min. and end must be< 10="">

  connect by startTime + (level - 1) / 24 / 6 - endTime< 1="" 4="">

  SQL> select * from shiftManager
    2  /
  
     DEPT_ID STARTTIME ENDTIME
  ---------- --------- ---------
           1 01-JUL-11 01-JUL-11
           2 01-JUL-11 01-JUL-11
  
  SQL> select  to_char(column_value,'HH24:MI') tm
    2    from  shiftManager,
    3          table(
    4                cast(
    5                     multiset(
    6                              select  least(startTime + (level - 1) / 24 / 6,endTime)
    7                                from  dual
    8                                connect by startTime + (level - 1) / 24 / 6 - endTime < 1 /24 /6
    9                             )
   10                     as sys.OdciDateList
   11                    )
   12               )
   13    where dept_id=1
   14    order by column_value
   15  /
  
  TM
  -----
  09:30
  09:40
  09:50
  10:00
  10:10
  10:20
  10:30
  10:40
  10:50
  11:00
  11:10
  
  TM
  -----
  11:20
  11:30
  11:40
  11:50
  12:00
  12:10
  12:20
  12:30
  12:40
  12:45
  
  21 rows selected.
  
  SQL> 
  

  SY.

• How we can plan automatic updates app and icloud backup at a specific time and off-peak hours?

  How we can plan automatic updates app and icloud backup at a specific time and off-peak hours?

  It does not work like that. It cannot be scheduled for a specific time.

• Is there a way to disable notifications for specific people or focus groups, without disabling notifications for everyone? (in messages)

  Is it possible, in messages, the rotation of notifications for specific people or groups of discussion, without disabling notifications for all incoming messages? I sometimes have a lot of messages from my daughter and my phone buzzes away all the time which can be annoying. I don't want to disable notifications entirely or do it on the silence on the other I miss important messages form other people.

  You can enable do not disturb on an individual message, but which will shut down the entire conversation if it's a group. This is not the same as activation do not disturb for the phone, which disables all notifications. Open messages, select the message in question, in the upper right, click details and then scroll to the bottom, you should find the switch to do not disturb.

• Send an email at a specific time with data

  Hello everyone, I hope that I write in the right forum.

  I am very new to LabView but I need quickly.

  Where I work they have a very complicated VI, a facility emailer who, when a fualts of tests for low current or overheating as the VI will send an email on what failing platform and on what date and the fault.
  I was instructed to have these VI email "update" every morning at 08:00, or any time, I decide.

  Basically, the email will contain,

  -Reference number

  -current test duration

  -temp... etc

  I guess I can do a while loop around the whole VI? What should I use to initialize an email at a specific time?

  I'm sure it's a question of newbie, so for that I apoligize!

  Thank you very much for your help!

  Ryan

  You can generate a dynamic event or...

• How if the stop message loop when I put looped at a specific time.

  I don't know how while loop stop at a specific time. Generally. While the loop stops when we enter into stop button or mistakes have been made. now I want to while loop stop at a specific time, 40ms, 20ms and so on. How can I achieve that. Thank you!

  Use the number of cycles. Get the current number of cycles when you run this loop.  Add your time (20 ms) to the starting value, creating a 'downtime '. At each iteration number of cycles review and compare the current value of the value 'stop time '.  If it is higher, then stop, otherwise continue.

  Note that on an operating system, you will see some jitter in trying to use loop as small as 20 ms times.  You may need to go to a real-time, or something hardware system timed for any accuracy or stability to these time scales.

  Lynn

• How to program Windows Live Sync to run at a specific time?

  I am trying to program Windos Live Sync to start and stop at certain specific times. I tried with the Task Scheduler"of Windows Vista, but it not start when I expected. Any suggestions?

  Thanks in advance!

  It will cost you a few logging you can check for errors, as well as the credentials of the user that the task will run under.

  Scheduler tasks and Robocopy batch
  http://www.howtofixcomputers.com/forums/Windows-Vista/Task-Scheduler-Robocopy-batch-job-69002.html

• I use Windows Live Mail for some time now without any problem, then today it just started freezing.

  I've been using Windows live mail for some time now with no problems then today it just started freezing. I open my mail box, receive mail, then I'm going to open a specific e-mail and it begins to freeze.  I have to close the program and start again and it then it freezes again.  Any suggestions?  I did a check for viruses on my laptop and it comes back clean.  Thank you!!

  All 'Live' programs have their own forums. The experts he can better help you.

  Windows Live Mail Forum
  http://www.windowslivehelp.com/forums.aspx?ProductID=15
  Bruce Hagen
  MS - MVP October 1, 2004 ~ September 30, 2010
  Imperial Beach, CA

• How can I configure my computer stops at a specific time?

  I know that I can set up Parental controls for other users, but I would like to be able to set a time limit so that the computer turns off. Is this possible?

  Thank you for your helpful suggestions.

  Loretta

  You can create a scheduled task that runs at a specific time every day. Its command line would be like this:

  stop, s, f, t 300
  The command will generate a group of pop up at the specified time, and then shut the computer down to 300 seconds (= 5 minutes) later. For information about how to create a scheduled task, click Start, click Help, then look for help on the scheduled task. When you create the task, make sure that it is running under the account 'System '. Initially, you must specify a time of 15 minutes now so that you can test the task shortly after it is created.
  If you find it intimidating to create a scheduled task then here is a simpler method:
  1 log in under an administrator account.

  2. click on the start planet.

  3. type the three letters cmd in the search box.

  4. press on Ctrl + Shift + Enter

  5. click on "run as Administrator".

  6. type the following commands and press ENTER after each:
  -22:00 / every: m, t, w, e, f, s, su shutdown.exe/s/f/t 300
  (to create the task described above. It will take place at 22:00).
  to
  (to see a list of all jobs created with this method)
  1/led
  (To remove the job #1).

• can I program windows 7 to start at a specific time?

  can I program windows 7 to start at a specific time and, for example, to play a full song on VLC file?
  FYI, I have windows 7 ultimate 64 bit version.

  Hello

  I suggest to see the link below and follow the steps provided by Andre Da Costa.

  Check if it helps.

  http://answers.Microsoft.com/en-us/Windows/Forum/Windows_7-desktop/is-there-a-way-to-AutoBoot-Windows-7-at-a-specific/8b586cbc-f40f-4784-A8F7-894275c1d07b

  Let us know if it helps.

• Choose that an audio specific time cannot define a specific "fade effect".

  Choose that an audio specific time cannot define a specific "fade effect". for example, I want to put a specific moment of the audio selected is set to-20dB fade effect (audio will not disappear), but I can't find this setting.

  Well, if you don't answer ryclark question, I'll tell you how you do in the waveform. If it's wrong, it's because you haven't we given the necessary information...

  Select the part of the wave that you want to fade out and open Effects > Ampliltude and Compression > envelope bland (process). Now select the preset "smooth fade out" and on the yellow line that is displayed, drag the end point + 10%. This will leave the audio 20dB above silence. Then apply this. You can save it as a preset if you want, and you can also change or add extra points to the wave of fade, change the way it fades.

• NIC team Active standby failover - how to see which physical adapter is actively used at a specific time by a VM or VMKernel port

  Hello, simple question.

  I have a vSwitch with two portgroup VMKernel. The switch is connected with two network adapters. The failover policy is set at the level of Portgroup. PG1 has active nic1 and nic 2 in standby mode. PG2 nic 1 standby and active NIC 2. I want to know via cli or gui, command which nic is actually used for a portgroup at a specific time. Is this possible?

  Thank you!
  Francesco

  You can see the active uplink for each vNIC in the network view (press 'n') with esxtop (r):

  

• How to import images set to a specific time length

  How to import images set to a specific time length? I make a slide show and pictures come to 20 minutes long, when I want to be 4 seconds. How can I configure the import to a second image 4?

  There is a setting preference for still life.

  Mylenium

• I need to reactivate Photoshop CS4 because I have a new hard drive in a reminder for my 2.5 yr old iMac last operating system running. When you open the program, I was told to contact Adobe support and give them an error code: 150:30. Please help with per

  I need to reactivate Photoshop CS4 because I have a new hard drive in a reminder for my 2.5 yr old iMac last operating system running. When you open the program, I was told to contact Adobe support and give them an error code: 150:30. Please help with permission. ?

  You can repair it yourself. I have a screenshot guide. You use app the Mac Terminal and a python (.py) script that comes with the recovery of the license for the Mac package.

  Don't forget to leave a space after typing sudo python and note that your password will not display any points. Simply enter it blind.

  Start 11 Message and take your time. It does not work. Layout error 150:30 opening Photoshop cs4 on Macbook Pro

  Gene