Replace cable Ribbon keyboard T420

Similar Questions

• Equium U400/146 - I need a replacement lcd cable/Ribbon

  Hello
  Please help I have searched for days.
  I need a replacement lcd cable/Ribbon. Identification number (DDOBU2LC000)

  My laptop is Toshiba Equium U400/146 PSU42E-00400SKS model number. Sound off out of warranty, so I took it to
  my local repair shop, but they could not get the part. The problem with the LCD is that it starts in green
  I can still use the programs, the grays and whites shine through.

  When it is connected to a crt monitor, the laptop is fine. Return to the cable, the screen number is REC-NI3311-LOL. C1

  If someone could point me in the right direction for this part, I would be most gratefull

  Thank you

  Hello

  All laptop parts can be ordered from the local ASP (certified partner).
  I think that guys should be able to order this cable/Ribbon.

  Here you can find the database with all FSA worldwide:
  http://EU.computers.Toshiba-Europe.com-> supported downloads &-> find an authorized service provider

  Good luck

• Portege R500 - replacement of the keyboard - success

  After buying a new keyboard for the R500 on EBay about a year ago, I finally blew the courage to replace a badly scratched by a new keyboard. The reason I've waited? I was worried about how to get out the old keyboard (it is locked down to the chassis, and it was obvious that I have would hurt one during the withdrawal.

  There is a nice write-up general on how to disassemble a R500 here:
  http://www.irisvista.com/tech/laptops/Toshiba-Portege-R500/disassemble-laptop-remove-hard-drive.htm

  The description above is not to discuss the keyboard however, so here's some additional information and tips:

  * Read this whole procedure before you start - it's simple, but not for the faint of heart.

  * Shut down, unplug the power, remove the battery.

  * Make sure that you have the correct keyboard for your model. The US keyboard is p/n G83C000903US for example. One I removed was a Rev 1 and a new one, I had a Rev 2 (don't know the difference - they look identical). They can get as low as $40-mais check the part number before you buy.

  * The keyboard connector is located under the computer, and so you will have to take off from the bottom, carefully following the instructions in the link above.

  A couple of notes: (a) the cable Ribbon PCMCIA connector must be opened to disconnect the cable, as this is the only thing that prevents you from removing the bottom of the computer. You can easily do so through access memory on the back door, but BE careful not to damage the cable lock. It works by switch to the top the little plastic lever that is held in place by small pieces of plastic on the sides of the connector that flex * a little *. Be gentle with this connector. When you put it back later-connector, if you placed the cable all the way into the connector, you can lock with only slight pressure down on the connector, and it will snap into place.

  (b) there are other types of cable Ribbon connectors use too. For example, to unlock the keyboard connector, now visible also on the bottom of the deck, slide both ends of the connector in the direction where the cable plugs in. They are snug and will only move about 1/4 ", be gentle but firm.

  (c) the two tiny connectors blocks free access to the water of the keyboard do not have locks on them. We're a band with only a few drivers, and one is a red and white power connector. Just pull out them. All the other connectors, you will probably miss through requires unlocking, so be careful!

  _Now back to the keyboard: _

  Once you have managed to disconnect his cable on the bottom, turn the laptop and start to remove the keyboard on the edges. It is supported by many small pieces of sticky tape, 2 faces, and that's it. As the base of the keyboard is made of aluminum, it is likely that you will distort the keyboard a bit as release you it, even though it may be downplayed maybe using a tool like a rule or something plastic and pry with it. Take care of not to damage the connector of the Ribbon and try to ignore these scary cracking sounds that identify each section!

  Once you have turned it off, you must remove any excess tape before starting point and again put a bunch of small pieces of new, good quality 2-sided tape (such as 3 m). No need to use anything stronger or thicker - just put a bunch of parts everywhere on the base, especially near the edges and the space key.

  Now, finally, turn the keyboard in position, making sure that you screw the connector back Ribbon through to the correct place. Turn the laptop over and re - insert and lock the Ribbon connector (make sure that it is directly and fully forward lock connector). All other connectors back in too. Then come back and push down hard on all sections.

  Re-assembling, taking care to put the 4 mm and 6 mm screws in the right places and a tiny on the side.

  Cross your fingers and turn it on!

  Good luck!

  Thank mate for this review.
  Generally the replacement of keyboard is not really complicated and someone with small technician skills should be able to replace it

• replacement of the keyboard to the other language

  Hello...

  Inspiron 15R SE 7520 version is available in several languages for the keyboard... Arabic.. Spanish..  US English... etc, and I can't find a replacement for my keyboard UK question...

  I live in the Sultanate of Oman,... If I can use any keyboard for laptop Inspiron 15R SE 7520 , as Arabic... Note my keyboard are 87 key, & touch there also 86 and they market online for the same laptop ? they are the same socket? Do I need for the new dell program?

  my laptop (UK Version):

  Inspiron 15R SE 7520, serial number:

  ADMIN NOTE: maintain the label removed by privacy policy >

  Hi basil,.

  Please write to us.

  Will be of the same type for any language keyboard.

  Once the new keyboard is installed the language must be added in the window of the region and language.

  Please go through this link on how to change the same.

  www.howtogeek.com/.../

  Provide us with your system tag #, name and e-mail via private message, by clicking on my name in blue and then select send a private message to use of records.

  Regardss

• HP 4200n replacement cable

  I have a HP4200n laser printer, and the cable from the back of the printer in the console of the computer is broken into pieces. Where I would be able to buy the replacement cable and y at - it a serial number for this spare part? HP says that she no longer has this part. Thank you.

  What kind of cable is it?

  Do you mean a DB25 parallel port cable?

  You can buy a third-partyvendor like this.

• Replace the standard keyboard with a backlit keyboard

  My dv6-3190sl features of a standard keyboard... is it possible to replace it with a backlit keyboard?

  the backlite keyboard should have an additional connector to power the light... I did some internet research... and I saw that this card mother dv6 had this connector, even if the keyboard is a standard.

  answer me please...

  concerning

  @lynnbartlett

  Hello

  This thread is about the dv6-3000 series models, and you have the model dv6-2000 series.

  The backlit keyboard can be installed in your model, because the motherboard has no connector for the keyboard light cable zif.

• AT200 - need an exclusive replacement cable

  Hi all

  Please help I need an exclusive replacement for my AT200 cable, Ive lost the original I know stupid and know that I must replace lead rare stupid thought the Toshiba with the addition of the port as a way to recharge.

  Also, I can't install the software updates Toshiba via USB.

  Ive checked out the official site of Tohisba UK he mentions reseallers etc, but can't find one in stock everywhere and if I come across one am shocked at how much they cost please help.

  I tried most of the web and I think I'll have to ring Toshiba direct but can't justify spending £35-40 on a leash.

  Ive tried loading via a charger 2Amp via micro Usb wire but it's too slow, even you charger outputs 2amps am unsure of the micro usb cable or port on the AT200 allows anything above 1 ampere, if even that.

  Thank you

  Hello

  I think that the compatible adapter AT200 (AC ADAPTER (UK) 2PIN 10W 2A) has a reference number: A200000340. Compatible USB cable has a reference number: A200000140

  I think that available in your country ASP could provide all of these parts

• Satellite A300 - replacement for the keyboard button problem

  Satellite A300 broken my number key 3.
  Easy to fix but still Toshiba have charged me £43 to replace it with a new full keyboard.
  It is less than 6 months old and still under warranty.

  What an absolute joke, I wouldn't have another toshiba again.

  > What an absolute joke, I wouldn't have another Toshiba again.
  Well, it is your personal opinion but I agree.

  However, if you understand something about laptops so you'd know that the single button can not be replaced.
  Only the CAP can be replaced but not the button on the keyboard, and thus the entire keyboard needs to be replaced!

  In addition, the guarantee only covers hardware problems that are not caused by laptop user I n don't know why the button on your keyboard is broken (maybe you was your fault) but I think that you have contacted the ASP in your country and talked to the technician then why you didn't explain that it wasn't your fault?

  In any case, the case should be clear now

• Replacement cables SHC68-68-EPM?

  I have a PXI-6363.  The recommended cable is the SHC68-68-EPM cable.  I have one of these practices, but need 2.  I found a couple of unused cables carrying around (NI SHC68-68 - RMIO & SHC68 - 68 - RDIO).  Can I use one of these as a substitute for a cable EPM?

  I am not convinced that you can simply replace them and if they don't work it wouldn't be ideal. On the one hand, the SHC68-68-EPM cable specifies that it ends by a shift of VHDCI 68 pin, while others are just VHDCI, but I was not able to find information about the difference. In addition, they list compatibility for X and M series for RMIO or RDIO cable. While they are all 68 pin cables there are huge differences in grouping and shielding wire, and they are all optimized for different features/data acquisition cards. I found the mappings of wire for the EPM and RMIO which illustrates this.

  Wire mapping list to the SHC68-68-EPM cable

  http://digital.NI.com/public.nsf/allkb/DE2D842E545DE64B86256F78006EAB1A

  RMIO cable Wire Mapping

  http://digital.natinst.com/public.nsf/ $CXIV/ATTACH-AEEE-88AQJT/$FILE/SHC68-68-RMIO.png

• replacement of Spanish keyboard for Yoga 14?

  Hello

  I recently bought this laptop at BestBuy: THINKPAD YOGA 14 - 20DM009GUS (2 in 1)

  I need to get the keyboard in Spanish (with the N key)

  This room is available for purchase? could someone give me the part number?

  I have the instructions to change the keyboard, but I need to get the replacement:
  https://support.Lenovo.com/us/en/documents/pd100305

  Good day and welcome to the community.

  From the parts FRU registration: https://download.lenovo.com/parts/ThinkPad/tp_yoga14_frubom_20151130.pdf

  It looks like you want: 00HW773 - Backlit KBD, 14Yoga,, CHY

  I'm not sure a good source to recommend outside the United States. Apology.

  I hope this helps a little.

  Kind regards.

• Can I replace the standard keyboard with a backlit keyboard on this laptop?

  The laptop is the Pavilion 15 p267-nr. I know that the new buildings have an option for a backlit keyboard, but I don't know about this particular model. It is possible that I would take it to a technician to do because this laptop seems very complicated to make upgrades to.  The keyboard that is currently a has not all icons in the F5 key, which is where the backlit function should be enabled on.

  Hi @Luis2,

  Thank you for visiting the HP Forums! A place where you can find solutions for your problems with the help of the community!

  I stumbled upon your post on the laptop and wanted to help you! I looked at your question about your HP Pavilion Notebook 15 - p267nr and need info on a backlit keyboard replacement. Here link to your page 21 of the manual and it shows me your laptop supports not the backlit.

  You can say thanks for trying to help by clicking on the Thumbs Up below!

  Thank you.

• Problems with cable eSATAp on T420

  I'm looking for help to find the right cable for use with my port hybrid eSATA USB Lenovo Thinkpad T420. I've tried the cables from 3 different sources, and none of them plug into the port of all the way.

  I don't know if my port is damaged, or if I'm just using the wrong cable, so any suggestions would be appreciated.

  Here are the most recent cable I got:

  Link to image 1

  Here are some photos illustrating the situation:

  eSATA pins on the port:

  Link to image 2

  USB pins on the port, with the back of the visible port. No obvious barrier I see...

  Link to image 3

  the eSATA cable pins:

  Link to image 4

  Pins of the USB cable:

  Link to picture 5

  As you can see from the photos, all the pins of the connector seem to match the port, except for the P12 and P13 12V power pins. These pins are present on the cable, but not on the port. However, I understand that these pins are optional...

  Anyone had a similar experience? I use the right cable?

  Thank you!

  Moderator comment: images > 50 KB converted for programming. Community rules.

  I saw your post in the forum 'other' thinkpad first and unrecorded. Here's what I said:

  I don't have a thinkpad with eSATA right now. My T520 has integrated graphics, (eSATA only on discrete), but I have a mother T510 here with discrete graphics card that has the same port. My eSATA cable plug AND there is a gap similar to that of your photo. I didn't measure the gap, but it is between 3 and 4mm. What does not work? Do you know that your eSATA drive requires a separate power supply? Powered eSATA ports are not generally available, and certainly, the port is not powered on yout T420. When I use a 2.5 drive "connected to eSATA, I use another cable that connects the cable power (+ than the 5V & ground) to a USB port. (USB on one end and SATA power supply on the other) I had my cable, but I'm sure you can find one on eBAY. When I use a drive 3.5 "I use a power supply from an old desk.

• Replacement of button keyboard individual/single keys available anywhere?

  My HP Pavilion dv7 Notebook PC has 1 missing a key cover on the keyboard.

  (Product number: serial number of A6X02UAR #ABA: 4CB2151110)

  The missing key cover or "button" is the right arrow key (>), which is in red and shown below:
  

         ^=Up

  Left = > =right

  Any suggestions on where and how I can get this one missing protects keyboard instead of buying and/or replacement of all of the keyboard?

  Thanks in advance!

  Carl

  Hi carlbattl,

  Welcome to the HP Forums!

  You have the best experience in the HP forum, I would like to draw your attention to the Guide of the Forums HP first time here? Learn how to publish and more.

  I understand you want to buy a unique keyboard key.  Here is a link to a Google page with options to this topic. portable keys.

• (Redirected) Dell Inspiron 14 7447 replace no backlit keyboard with backlit?

  Hi, the laptop 7447 Variant (i5) 14 I have been no backlit keyboard variant they sell in the Philippines has no backlit keyboard. The feature is extremely useful, so I would ask:

  The backlit keyboard not can be replaced by a variant of backlit?

  Hi Mathew8991,

  Please repost this in the laptop computer forum help

  http://en.community.Dell.com/support-forums/laptop/

• How can I find a replacement for the keyboard and mouse Microsoft Sculpt?

  A feafae of replacement can be ordered if I broke one for my mouse wireless Sculpt & keyboard?

  My apologies, Mark;

  The link is broken for the validation of my answer somehow. I fixed it and here is another.

  Microsoft Hardware support