replacement of the console commands?

Similar Questions

• replacement of the alias command

  I would use the MDP to manage my PIX. My config is currently using the alias command. Can I replace the alias with static controls?

  Thank you

  Alias of (internal) exodus 192.195.176.17 174.18.2.20 255.255.255.255

  In fact, the keyword "dns" on the second static shouln t be there. You need the 'dns' on the first static for hosts on the DMZ are the real IP and not the NATted in DNS answers. Make sure that you "clea xlate" after these changes, clear dns caches (ipconfig/flushdns on win2k/xp), and that there is not the host entries in the affected machines. For your configuration, you should have this:

  static (dmz, outside) 123.123.123.123 192.168.1.1 dns netmask 255.255.255.255 [keyword dns tells the pix to DNS doctoring for this translation because DNS resolves the public IP address]

  static (dmz, inside) 123.123.123.123 192.168.1.1 subnet 255.255.255.255 mask [allows the internal hosts to connect to the public IP found in DNS and it translates the private IP on the way to the demilitarized zone]

• ESX3i - can I remove snapshots from the console/command line?

  In ESX3i remove an instant expansion of the VI Client takes too long the client times out and appears to block all connected VI customers.  Is it possible that I can delete the snapshots of the console (not supported)?

  Yes, you can, just know he has not supported but works, take a look here: http://engr.ucsb.edu/~duonglt/vmware/#vmware_vimsh

  vim-cmd vmsvc/snapshot.removeall [VmId]
  vim-cmd vmsvc/snapshot.remove [VmId] [removeChildren] [snapshotLevel] [snapshotIndex]
  

  You can also take a look at the vCLI/RCLI utility snapshotmanager.pl http://www.vmware.com/support/developer/viperltoolkit/viperl15/doc/snapshotmanager.html

  =========================================================================

  William Lam

  VMware vExpert 2009

  Scripts for VMware ESX/ESXi and resources at: http://engineering.ucsb.edu/~duonglt/vmware/

  repository scripts vGhetto

  http://Twitter.com/lamw

  If you find this information useful, please give points to "correct" or "useful".

• What is the service console command to give the IP address of the ESX host?

  What is the service console command to give the IP address of the ESX host? /

  What is the command to give the IP address of a host that has no IP?

  see this

  http://KB.VMware.com/kb/4309499

  It's good to have as well

  http://VMware-land.com/esxcfg-help.html

• Need help with commands from the console.

  Guys,

  I'm discovering nuer console which is attached to a particular hba.  I have connected to the console and you have run the following command

  cat/proc/vmware/scsi/vmhba1

  It returns a message saying something like "this is a directory" now all I have is a blank screen with a blinking cursor and I can't go back to the root.  Can someone help me to pease keep in mind Im these commands do not at all know.

  Thank you.

  ... try with CTRL + C or ": q!"

  CAD commands reference

  Bye bye

• How can I disable the damned shortcuts to the web developer? E.g. reopen a page Ctrl + Shift + T now opens the console, do not have the basic FF command... Terrible.

  The shortcuts are the same - tools for web developers are now open for CTRL + SHIFT + T rather than reopen a closed tab, etc... It is very annoying.

  I can't delete web developer, but I never wanted to install it.

  Subject: config does not work, or reinstall Firefox...

  Is there one solution other then moving to Chrome?

  Hello!

  I know this is an old post, but I found the solution to your problem.
  I had the same problem but with adblock plus (extension of masking element).

  It uses the same combination of keys ctrl, shift + k and when was rush to the web developer of this combination has opened...

  To DISABLE this shortcut, you must OPEN the console of the web developer and click on the gear which is located in the left side.
  Then, UNCHECK the box that says Console and press the X on the far right close the console.

  Disable your Add on and turn it on again and you'll be fine.
  (or restart Firefox)

  In my case it worked well and instead of "null" in the key of the element AdBlockPlus combination hide now, he says the corresponding key and no longer opens the "web developer console.

  I hope it helps

  (if you want I can provide before/after screenshots to see)

  Thank you

  Dimitris

• service console commands not show the non-root user

  Hello

  If I create a user with shell access none of the SC commands are available, even if I KNEW the root. As soon as I give you shell access to the root the command that are available once more.

  I tried add the user to the root user group account but still have the same question.

  Am I missing something?

  Thank you

  Type su - (less known space)

  Or su - root

  André

• How to open the console design

  Hello friends am new on oim 11g
  I just finished with the facilities (wls, IOM, etc.)
  I created a user with connector gtc (only reconciliation) now I want to generate Email user id based on his first name and family name
  people me to go console fo design, suggesting how to go to console design and generate email identification.
  
  Please help me with the above query
  
  Thans in advance

  Use the following steps to create a file wlfullclient.jar for a client application to JDK 1.6:

  Replace the directories in the server/lib directory.
  CD WL_HOME/server/lib
  Use the following command to create wlfullclient.jar in server/lib directory:
  java-jar wljarbuilder.jar

  Now copy this file jar to the Oracle_IDM1/designconsole/ext folder

  After that, go to the folder Oracle_IDM/designconsole

  and run the xlclient.bat file, it will launch the console design.

  HTH

• kernel: disk0s2: error IO repeatedly appearing in the activity of the Console. He says this hard drive is faulty?

  I've recently updated for the SSD, and it was a bit of a bumpy road so far.

  I get these messages in the console app a lot

  kernel: disk0s2: i/o error.

  My new hard drive isn't a lemon or is it a software problem?

  It does not necessarily mean that the SSD is a failure. It could also be a problem with the SATA cable. Check if it is probably connected and/or replace it.

• repeating the DCs error in the console

  I have a repetitive message in the Console, which is repeated exactly every 30 seconds or more... This I would appreciate any advise about what this can be, and how I might be able to solve. Thanks in advance for any advice!

  I have an iMac (retina 5K, 27 inches, end of 2014), El Capitan Version 10.11.5 (15F34) running. I copied the two rehearsals directly from the Console application.

  May 25 07:44:57 iMac DCs [360]: SOSPeerCoderSendMessageIfNeeded omxnNgZCVvvURMf11h320hLKvs getCoder: Domain error Code = com.apple.security.sos.error = 1032 "no coderData or encoder for peer: omxnNgZCVvvURMf11h320hLKvs" UserInfo = {NSDescription = no coderData or encoder for peer: omxnNgZCVvvURMf11h320hLKvs}

  May 25 07:44:57 iMac DCs [360]: SOSEngineCreateMessage_locked + ioW618FpBgIOyiqNDJ1Or0JeB: JkkzpREit8hbVLJ3KBM0m3umY0 error in send: Domain error Code = com.apple.security.sos.error = 1032 "no coderData or encoder for peer: omxnNgZCVvvURMf11h320hLKvs" UserInfo = {NSDescription = no coderData or encoder for peer: omxnNgZCVvvURMf11h320hLKvs}

  May 25 07:44:57 iMac DCs [360]: __SOSCCProcessSyncWithAllPeers_Server_block_invoke sync with all counterparts failed: Domain error Code = com.apple.security.sos.error = 1032 "no coderData or encoder for peer: omxnNgZCVvvURMf11h320hLKvs" UserInfo = {NSDescription = no coderData or encoder for peer: omxnNgZCVvvURMf11h320hLKvs}

  May 25 07:44:57 iMac CloudKeychainProxy [445]: _block_invoke_2 __39-[UbiqitousKVSProxy doSyncWithAllPeers] < UBK-s-pCS - > syncWithAllPeers (null), rescheduling of the timer

  May 25 07:44:57 iMac CloudKeychainProxy [445]: + [SOSPersistentState: write error: data:] cannot save PersistentState in XML

  May 25 07:45:12 iMac DCs [360]: SOSPeerCoderSendMessageIfNeeded omxnNgZCVvvURMf11h320hLKvs getCoder: Domain error Code = com.apple.security.sos.error = 1032 "no coderData or encoder for peer: omxnNgZCVvvURMf11h320hLKvs" UserInfo = {NSDescription = no coderData or encoder for peer: omxnNgZCVvvURMf11h320hLKvs}

  May 25 07:45:12 iMac DCs [360]: SOSEngineCreateMessage_locked + ioW618FpBgIOyiqNDJ1Or0JeB: JkkzpREit8hbVLJ3KBM0m3umY0 error in send: Domain error Code = com.apple.security.sos.error = 1032 "no coderData or encoder for peer: omxnNgZCVvvURMf11h320hLKvs" UserInfo = {NSDescription = no coderData or encoder for peer: omxnNgZCVvvURMf11h320hLKvs}

  May 25 07:45:12 iMac DCs [360]: __SOSCCProcessSyncWithAllPeers_Server_block_invoke sync with all counterparts failed: Domain error Code = com.apple.security.sos.error = 1032 "no coderData or encoder for peer: omxnNgZCVvvURMf11h320hLKvs" UserInfo = {NSDescription = no coderData or encoder for peer: omxnNgZCVvvURMf11h320hLKvs}

  May 25 07:45:12 iMac CloudKeychainProxy [445]: _block_invoke_2 __39-[UbiqitousKVSProxy doSyncWithAllPeers] < UBK-s-pCS - > syncWithAllPeers (null), rescheduling of the timer

  May 25 07:45:12 iMac CloudKeychainProxy [445]: + [SOSPersistentState: write error: data:] cannot save PersistentState in XML

  Please take these steps to resynchronize the iCloud keychain. Your keychain on iCloud and other Apple devices will be unaffected. Take step 2 only if step 1 does not resolve the problem.

  iCloud Keychain has quite complex security measures that can be difficult to work with. It also has its fair share of bugs. If you have doubts about whether you can carry out instructions below, it may be best to contact the Apple Support before doing anything.

  Step 1

  Back up all data.

  Open the iCloud pane in system preferences and uncheck the keychain. You will be prompted to delete the keychain local iCloud. Confirm - the data will remain on the servers. Then re-check the box. Follow one of the procedures described in this article to support to implement the iCloud Keychain on an additional device. Test.

  If you can't disable iCloud Keychain because the box itself check again, disable it on all your other devices first, and then try again. Before you do, make sure that you can use at least one of the methods given in the related support above, article under the heading

  How to configure iCloud Keychain on a new device without another device to approve of?

  Step 2

  If your problems persist, uncheck the keychain again and continue.

  Triple-click on the line below on this page to select, then copy the text to the Clipboard by pressing Control-C key combination:

  ~/Library/Keychains

  In the Finder, select

  Go ▹ go to the folder...

  from the menu bar and paste it into the box that opens by pressing command + V. You won't see what you pasted a newline being included. Press return.

  A folder named "Key ring" should open. Inside, it is a subfolder with a similar long names (but not the same as) that:

  421DE5CA-D745-3AC1-91B0-CE5FC0ABA128

  The above is only an example; your will have a different name for the same general shape. Drag the subfolder (not the key ring file) to the trash.

  Restart the computer, empty the trash and reactivate iCloud keychain.

• Premium HP: HP Premium - problems with the TRIANGLE_P command in the programs.

  I have version 2015 7 28 (8151) firmware and can not be updated any further because I have only the Android app.

  Maybe the next problem has also been fixed already in a more recent update, as a previous problem of mine. We'll see.

  I want a 3-dimensional triangle of the project on the screen using the advanced form of TRIANGLE_P.

  First the good news.

  The following program works:

  EXPORT experiment1
  
    BEGIN
  
       LOCAL P1, P2, P3;
  
       RECT_P();                   Clears the screen
  
  P1: = {100,100,75};
  
       P2: = {200,100,75};
  
       P3: = {100,200,225};
  TRIANGLE_P ({P1, P2, P3}, {{1,2,3, #FF}});
  GEL;
  
    END;

  Explanation: I define three dimensions 3 points P1, P2, P3 and insert them in a list in the triangle command. What are the angles of the triangle.

  In the second argument, I defined the triangle specifying these points in the first list indices, which are 1,2,3. #FF means that it is blue.

  Here is the result:

  

  It's not very spectacular, because the only thing that the program leaves the coordinate z points away and drawing of the triangle 2 dimensions resulting. So there is not a lot 3-dimensionality thereon. In fact nothing.

  Now, I'll try to do a little more complicated by the third argument, I have left aside until now. The first 2 arguments are the 2 lists of lists.

  The simplest form is a rotation matrix or list trivial-{1}:

  Syntax: TRIANGLE_P ([G], points_definition, triangle_definitions,

  rotation_matrix or {rotation_matrix or - 1, ["N"], [{eye_x, eye_y, eye_z}

  or - 1], [{3Dxmin, 3Dxmax, 3Dymin, 3Dymax, 3Dzmin, 3Dzmax}]}, [zstring])

  User manual

  The simplest rotation matrix is the identity matrix which consists of all zeros except the diagonal elements, which are 1. So I create this way M1.

  Now, I have replace the triangle command by:

  TRIANGLE_P ({P1, P2, P3}, {{1,2,3, #FF}}, M1);

  Or

  TRIANGLE_P ({P1, P2, P3}, {{1,2,3, #FF}}, {-1});

  "Two return output programs: ' error: invalid entry.

  "I tried several forms of the third argument, for example by specifying all possible sub arguments, but all what I try, I always get nothing else than: ' error: entry invalid.

  So I would like to know if if my firmware update is the cause, or I did something wrong or it is a bug.

  Hello

  I thought about it...

  The 'problem' is that, with only 3 entries in the first list and matrice matrix of a rotation, think the system, the first review, 3 3 points x, y parameters are, z coordinates for each of the 3 points. On second review, we see that they are not valid and an error. This stems from the fact that the Triangle can take so many different types of arguments and that it is not always easy to distinguish between the different forms.

  You can make sure the system interprets the input data in the form that you want to ensure that the list of the point has at least 5 Articles (even if they are not used). Then, he will work as in:

  EXPORT tt
  BEGIN
  LOCAL P1, P2, P3;
  RECT_P();                   Clears the screen
  
  P1: = {100,100,75};
  P2: = {200,100,75};
  P3: = {100,200,225};
  
  TRIANGLE_P ({P1, P2, P3, P1, P1}, {{1,2,3, #FF}}, [[0.5,1,0,0], [0,2,0,0], [0,0,1,0], [0,0,0,0]]);
  
  GEL;
  END;

  Cyrille

• Distorted screen of the console using Ubuntu Linux on Satellite C70-B-212

  Hi all

  I have a problem with Linux on my laptop Satellite C70-B-212. The videochip Intel Graphics 4400 is supported by Linux, but on this laptop, it gives very distorted output on the console screen. I see a few vertical lines on the screen showing a few ghosts strange images of the output.

  The Office of exit itself seems to stop smoking well, until I have a screen and move it to the bottom of the screen. You can see the top of the screen some distortion in the upper line.

  In Windows everything works fine. When I use the parameter 'nomodeset' turns off the kernel mode setting these lines do not appear. But then, I expect that 3D hardware acceleration is disabled too.

  I suspect that this is a timing issue with the screen of the computer. Just a very minor lag on the clocks or sync.
  It could be just my laptop and then it just cloud be replaced or maybe it has to do with the series.
  Anyone seeing the same issue on this model or series.

  Having Linux on C70-B-212.
  Who can verify this by starting Linux liveCD on laptop C70-B-212.

  Thank you

  Marco

  Hi Marco

  It sounds like a driver problem => kernel.

  You can try a kernel later maybe?
  Do you know that you are using atm?

  in terminal type:

  uname - r

  Course Fedora uses 3.16 nuclei which is a very recent (if not the most recent) output.

  Some Ubuntu distro oriented have test of nuclei in the repositories, you will have to add it manually.
  Maybe it's worth a try?

  Tom BR

• Messages in the console mdworker and lsd

  On every few minutes, I get a hundred lines of messages in the console log.

  Kernel: Sandbox: mdworker (PID #) deny (1) - reading data from the file with the path to applications.

  What causes them and is there anything I can do to fix all these?

  I also get a lot of these minutes.

  LSD: LaunchServices: could store not lsd-identifier file to /private/var/dv/lsd/com.apple.lsdschemes.plist

  Same question, what causes them and can I do to solve this?

  Or are these just harmless noise, just a lot of it?

  I found mdworker messages are for mds_stores damean for projector which was unaware of the spotlight exclusion list (all HD on Mac) and consumed nearly 600 MB. I found the command, sudo mdutil - a-i off < cr >, enter the admin password, to stop the process, and mds_stores goes back to 175 MB. Apparently, there is a gap between the projector and mds_stores.

• Why a search of the console finds not all instances?

  For a long time, I used the Console to track my start and stop times to fill out a time sheet company. Since I upgraded to El Capitan (certainly of 10.6.8) research in console are totally reliable.

  I have a query log saved to the content of the 'Got boot device' message that usually gives me a list of departure times.

  A query saved to 'stop' or ' stop of "me gives stop times.

  But both strange, these searches find nothing. Today, for example, my first search captured all my time Starter for the past two weeks, but the second search returns only results from a week at the back. WHY? Paging trudged through all messages brings back me beyond that point in journal entries that meet the search criteria, but today the saved query is just ignorant.

  What gives? I never had this kind of behavior laminated with previous incarnations of Console.

  Is there an easier way to get a list of start and stop times?

  You can use Terminal and the 'last' command (without quotes) for a list of the connection history.

  

  It gives the date, the start - finish time & duration, time closed parentheses.

• Unable to open the console (~) inside the game of oblivion.

  Hi guys, I have first pick in forums and countless other sites including instances of Bethesda Softworks.
  You have 2 similar cases with the console of the game Fallout 3.
  However, I turned to Microsoft for answers, because I found the problem: just need a specific solution.

  Information on my computer:

  Dell Studio XPS 1340 (laptop)
  Windows Vista Ultimate updated to service pack 2 (64-bit)

  To only justify some obvious things:
  -Yes my computer meets and exceeds the requirements of the game.
  -Yes the ~ button works in other programs.
  -Yes, I tried Shift + ' do ~ in the game (does not work)
  -Yes, I have uninstalled and reinstalled the game
  -Not my computer did not come with a remote
  -J' entered in the menu options (in the game) and changed another command for example like button next with ~ to see if the game was recognized and it didn't.

  There are a few bugs that can be made initially to counter the problem with the console.

  • Change the size of the screen so that you can see the "missing" console (where infact it was just out of sight)
  • Set up the document Oblivion.ini - bAllowConsole = 1 (corrected most of the problems where it was set to 0)
  • Download a mod to change the game and use it to activate the console in a different way (in this case using equipping an item)
  • If you have Microsoft Media Center, then; Disable the MIRC / Microsoft transceiver eHome infrared (or (EC) ITECIR infrared receiver), or inside of the appliance to manage

  My specific problem I have identified is that my laptop has a built-in infrared censor (and has the installed Microsoft Media Center), this has been identified on many forums as contradictory with the game console button (~). According to most of the solutions that have been validated by disabling it should fix it.

  I found the Microsoft eHome infrared transceiver AND IR receiver ITECIR (EC) in my device manager under human interface devices.
  But I can not disable - the option is greyed out =)
  (And Yes, I'm the administrator of this computer [the only account as well])

  So to make a very long explanation to a question.
  How can I disable the infrared in my device manager hardware when I am the administrator, but it is grayed out?

  Thanks for your time, Cappwood

  Hey Cappwood.
  I was searching Google earlier, I have the same problem. Sometimes I play a game called "Farcry" and in order to show the console (for once coming from servers if they are tks, spwnkillers, cheaters, etc, and of course the order entry), I have to set up the "key (located under my ESC key). Until today, I have to keep uninstalling 'infrared transceiver Ehome' whenever I start my computer laptop, or sometimes just when I connect a mouse or something.
  Fortunately, I found a solution on Google :) (The below is copied from another forum):

  (* Note that if you have Microsoft Ehome... you click right on this and uninstall for number of step 3).

  Originally posted by epic
  SOLVED! Here is what I did to fix it (and no need to uninstall it whenever you want to play XI):

  (1) disable automatic driver downloads:
  -Start menu-> right-click computer-> properties-> system settings advanced (upper-left)-> hardware-> Windows Update driver settings-> select 'never check the drivers when I connect a device.' -> OK-> Apply-> OK

  (2) disable SSDP Discovery:
  --> Start menu type "services.msc" without the quotes and press enter-> scroll down to "SSDP Discovery"-> right click and select Properties-> change Startup Type to "Disabled"-> Apply-> OK

  (3) uninstall ENE CIR Receiver:

  
  -Start menu-> right-click computer-> manage-> Device Manager-> click on the + next to Interface devices-> right-click "ENE CIR Receiver" and select uninstall-> MAKE SURE to CHECK THE UNINSTALL SOFTWARE BOX ON THE PROMPT (it will take Microsoft eHome Infrared Trasceiver with it)-> OK-> let the uninstall, take turn-> restart the computer

  (4) prevents the installation of IR device drivers:
  -Upon restart, you will receive a prompt asking you if you want to install the device drivers-> SELECT NEVER "for this DEVICE.

  (5) turn the SSDP Discovery:
  -Follow the signs to start and select 'Manual' from the drop-down menu (Startup Type)-> Apply-> OK

  (5) play XI
  -

  A credit of Milton on the BG Forums for the SSDP Discovery thing. Feel free to post these instructions in any thread on this issue. Enjoy!

  The thread of the forum can be found here, if you want to have a glance / thank so much! :

  http://www.bluegartrls.com/Forum/67734-uninstalling-Microsoft-eHome-infrared-transceiver.html

  As Epical says, thanks to Milton, Epical comes to the solution in a little easier to follow the steps. Milton has provided the solution :) But still, I personally thank Milton and Epical much for this, it was just one of those annoying things in life that I thought could easily be avoided.

  I hope it works for you,
  Jamie B.