Replacement of the power supply

Similar Questions

• Pavilion m9670ch Desktop: replacement of the power supply

  I replaced the original power supply with another more powerful (550W) earlier, I bought a new graphics card. This power is very strong, that's why I bought a new DARK PRO 10 power SUPPLY ATX 550W. Now, the computer does not start. When I press the power button, the fan starts momentarily and stops again. All cables are correctly installed. I reinstalled the old power supply (fort) again and everything works normally (except for the noisy fan). I contacted the manufacturer of the unit from the POWER of DARKNESS, but he referred me to HP, because they did not have a solution, but it may be a peculiarity of the motherboard. What can I do?

  Hello

  Return the Dark Power Pro and get a Corsair CX500, or CX600.

• Replacement of the power supply for SG3-120UK

  I am looking for a compatible power supply replacement for a desktop Compaq SG3-120UK, which has a block of power SUPPLY Bestec ATX0180 P5WB. Now, this power supply is defective. Can anyone recommend a suitable replacement?

  Can you provide the steps?

  The only source that I found in the United Kingdom says "call", as it is out of stock:

  http://microdream.co.UK/Bestec-atx0180p5wb-ATX-180W-PSU-power-supply.html

• Replacement of the power supply (very not worry, that it does not or other problems)

  I had an acer M985 and a power supply Liteon-on PS-6301 - 08A 3

  I want to replace it with an XFX 550W 80 + Bronze certified ATX Power Supply will he adapt to my case? There will be wiring problems? (my diet's die my pc shuts off automatically checked by highpoint, but my warranty is over, so I want to replace it for a better)

  Hi limtenggen

  This power supply will fit your Acer very well. There will be no problem of wire at all!

• Equium L10-273 - replacement of the power supply charger

  Hello

  After 2 1/2 years of relatively good service, my charger for my L10 273 died and went to heaven. I had a couple of universal Chargers since but the bit that connects to the adapter for different brands of laptops to the bit that starts is made of 2 pins that seem to constantly break. Can anyone recommend a place where I can get a charger replacement for less than £30 and is not maintained by two thin pieces of metal?

  This is what I got:
  http://www.Maplin.co.UK/module.aspx?ModuleNo=217916&&source=14&doy=28m2

  Hello zizou

  Just a quick comment: I don't really know if you have financial problems, but if possible buy the right replacement. I want to say that the best thing is to buy the same adapter. You will be safe and I hope that the next 2 and a half years without problem.

• Questions about the replacement of a power supply for a P7-1235

  I decided to do an update on my Pavilion P7-1235. I put in a graphics card and put in power level. After doing some research on this forum and others I know well enough that I need. The only question I have is about the food. I don't know what the original power supply. There is a vent on the side where it however. So I guess that there is a fan on this side of the power supply. This eating plan I get:

  http://www.Newegg.com/product/product.aspx?item=N82E16817139050 & TPK = % 20500% 20% 20modular %2 watt Corsair...

  I noticed that the fan is on top? Now there is no high ventilation in my P7-1235, I worry for nothing? I think that all the supplys to look the same. What is the top of the fan page for? Or can anyone suggest a replacement perfect for my exact Pavilion model?

  Sorry if the questions are stupid, but I'm still learning and want to do what I can myself!

  Hello

  Yes, you can use the power supply the same way. The image is in a vertical position for the convience of the buyer. I have the same with number of power supplies and it was fine. You can check the following links people have set up exact POWER supply in different ways.

  http://pcpartpicker.com/builds/by_part/Corsair-power-supply-cx500m

  However, please be aware of your power supply size and your case. If you have all materials/components in stock for your computer, then it is what it is;

  ATX case:

  : Height 39.4 (15.55 inches)

  Width: 17.5 cm (6.89 in)

  Depth: 40.9 cm (16,14 inches)

  PSU stock:

  (5.9 x 5.5 x 3.4 inches)

  And the power supply you want;

  Corsair size;

  "5.9"x 3.4"x 6.3"

  As you can see the length of the Corsair is considerably larger than your stock of power supply. This could hampor of air or could even make it so the holes of the PSU and the case does not match. However, this is usually not what worry. The height and width that should be worried because the length rarely causes problems, I wanted to just make sure that you knew in advance.

  Take advantage of your power supply; Corsair is a great brand.

• Replace the power supply, computer does not turn on

  I had a Seasonic SS 560 KM power supply for my HP Pav e9280t.  I removed the old power supply while keeping the power cable is plugged in.  Then replaced each power cables one at a time in the new power supply and finally he attached to the tower.

  Now when I try to turn on your computer, it just boots barely upward.  I can hear the fans kick on for a second or two, then everything just stops.

  Since I replaced the cables one at a time I don't think I missed anything; MoBo, Fan of MoBo, 1 optical drive, disk HARD 2 and 1GPU.  The tower is open and I can see the fan, the fan GPU MoBo and PSU fan all hang on one second so that they get the right power?

  I must have missed something or possibly faulty PSU?  Any help will be appreciated.

  Hello Chadow86, it is possible to the new power supply may be faulty. I would check double all the connectors again.

  Since you mentioned the fan to the motherboard, it would not be necessary to unplug the CPU fan when you changed the power supply. The CPU fan power source comes from the motherboard and not directly from the power supply. I don't know what fan on the motherboard you are talking about.

  I watched the specifications and photos of the new power supply. It is a modular design. I would check the cables connected to the power supply to make sure that they are in the correct connectors.

  If the system still does not start, the cause could be a new power supply faulty.

  I hope this helps.

• Replacing the power supply on a HP Pavilion P6000

  Outputs video (DVI and VGA) were both released on my motherboard. Rather than go through the hassle of dealing with Microsoft if I had to replace the MB, I decided to install a MSI Geforce 210 graphics card and the existing PCI express slot. However, the existing power is rated at 250 watts and the new video card got a minimum rating of 300 watts. It seems to work, and I don't do any high-end graphics or game. My main uses of the PC are paying bill online, e-mail and a few online forums. Should I replace the power supply with a higher nominal? I have a Hiper Type R PSU which is estimated at 580 watts and was planning to replace it with the 250, but it looks like not her suits because it is deeper than the power installed about half an inch. The deeper power looks like it should stick on a half inch at the rear of the computer when it is against the stop before power in the case. I would like to have some advice on the use of the existing offer or be able to use my power Hiper 580.

  The HP Pavilion P6617C model, which is the number of product BT427AAR developed a standard ATX size power supply. Dimensions (as you know) are 5.9 "x 3.4" on the back and depth 5.5"in the case. The small metal latch/stop button to slide the power supply existing forwards (for removal). There really is no support.

  4 rear mounting screws fix the power supply of the Cabinet. Of concern would be the length, an added 0.7 ", as well as cables/connectors.  You can try the Hiper in the case, and if it fits, OK. Otherwise, I suggest a diet that actually matches the Rosewill 630W

• CPU constantly tries to reboot - just replaced the power supply - and can't get into Windows at all the

  I replaced the power supply 2 weeks ago and left the computer.  Follow me up one morning, the computer froze and when I tried to reboot, it whirs and stops... 5 seconds later same thing.  The power button lights up orange... someone can give me an idea of the problem?  Defective power supply replacement?

  Hi Cathy,.

  This seems to be a hardware failure. You must get in touch with the manufacturer of the system or the local Techshop for better assistance.

• Can I replace the power supply on my desktop dell?

  I have the dell Inspiron 3847-3850BK and it's an inspiron with i3 processor. And my question is, can I replace the power supply on this desktop computer... The PSU is a l300nm-01. And also the PSU, I own the ATX form? NOTE: NOT THE MINI TOWER.

  Skrullknight

  I have the dell Inspiron 3847-3850BK and it's an inspiron with i3 processor. And my question is, can I replace the power supply on this desktop computer... The PSU is a l300nm-01. And also the PSU, I own the ATX form?

  Skrullknight

  Yes, the Dell Inspiron 3847 Mini-Tower can use generic power supplies ATX, with either a power connector 24 pin or 20 + 4 pin card mother main, with or without the on/off switch.

  You should be able to buy a compatible power supply either a local computer or online store.

  Note: You need a diet with four SATA power connectors.

  Bev.

• Replace the power supply in a Studio Slim s 540

  Hi, I bought a 540 s Slim of Studio in November 2009 and now I've decided I want to make games a bit. However, it runs a little hot, and there is not enough energy for a new card. I think I have a power supply that is 300w.

  I was watching a GTX 460 or ATI 5850. The 5850 is probably too much for the case. So I thought to replace the case by something simple but effective. I like this:

  http://www.Newegg.com/product/product.aspx?item=N82E16811119137&nm_mc=AFC-C8Junction&cm_mmc=AFC-C8Junction-_-RSSDailyDeals-_-na-_-na&aid=10521304&PID=3136390&SID=

  This case should be quite good, with the addition of a fan or two perhaps.

  Now to my next problem. I keep everything in the Studio Slim to the stock, the Quad Core, 6 GB of ram, etc. The only thing that changes is the power supply and graphics card. However, I've heard Dell Mobos/PSU are owners and making it difficult to replace PSU. I have need around a block power 400w-500w. What is compatible with the dell motherboard chipset? Help would be appreciated, thanks.

  Some of my features, if it helps:

  Motherboard: Dell 0M017G A00 P45/P43 chipset
  CPU: Intel Core 2 Quad Q8300
  RAM: Twin 400 mhz (DRAM frequency) 6 GB DDR2 memory
  HARD drive: Western Digital 7200 RPM 32 MB Caviar Black

  PSU: bed 10A 125v so I think that its to 300w?

  deuce985

  The Studio 540 Slim has a 250w power supply.

  The power supply is a standard ATX format, but due to the constraints of the 540 Slimline case, it is a unit of owner of Dell, due to its shape, size, and the wiring harness.

  If the motherboard has been installed in a box ATX Mini/Mid Tower standard, more generic standard ATX power supplies can be associated, either a 24-pin or 20 + 4 pin main card mother power connector, with or without the on/off switch.

  You should be able to buy a compatible power supply either a local computer or online store.

  Note: You need a diet with four SATA power connectors.

  Bev.

• Replace the power supply on my m9340f

  Hello

  I own a Pavilion Elite m9340f and I need to replace the power supply (it has the original), because the power on button failure, which I did research on forums and the solution replaces the power supply (psu led always on, for example).

  But I need to know exactly what kind of food I buy (amp, voltage, PIN number, dimensions, etc.) because I need help on the specifications.

  I'm not planning to upgrade the motherboard the case, original hp. I read in another post something on the power restriction and benicia supporting more than 450 watts power supply motherboard. I find this absurd information, because components draw necessary power from the PSU without worrying if it's 350 or 700 watts. So is one of the things that I need to be confirmed if there is restriction of power.

  Thanks in advance,

  Prince of Jeronimo Ramos

  Jeronimo, welcome to the forum.

  I believe that any standard ATX PSU must be inserted into the case.  I like Corsair and OCZ.  They are excellent manufacturers.  I suggest to measure the PSU existing and comparing measures to whichever you choose.  As far as I know, there is no restriction on the power.  I did this for a long time.  More than 550W to 600W in your computer is not necessary, however.

  If your problem is solved, please click "accept as a Solution.

• I want to replace the power supply and graphics card in my p6550z

  Hello

  I'm looking to replace my power supply (BESTEC 300 watts) and the graphics card (ati radeon hd 5450). Here is a link to the HP page with my pc: http://h10025.www1.hp.com/ewfrf/wc/product?product=4242359&lc=en&cc=us&dlc=en&lang=en&cc=us

  The card I want to put is an Amd Radeon HD 6870. And I also want to put in a block of power SUPPLY Corsair 550 Watt.

  They will work when I install them? (I'm actually a little nervous about the upgrade my power supply and graphics card since it is the first time I'm doing this) (I'm also nervous because I've heard many horror stories about upgrading an HP computer)

  Hello

  There is a small metal tab inside (guts) on some models of PC HP adds stability to food. You'll have to push the tab down to get food out.  The link below will show this tab.

  How to replace a power supply.

  How to replace a video card.

  Corsair power supply (psu) I used can be mounted with the fan facing upwards or downwards depending on where fresh air is available from. Some PC cabinets have mesh ventilation where the PSU Monte so the fan should face the ventilation mesh so that fresh air can be brought into the power supply and then exhausted at the rear. Some HP computers have slots to air ventilation through the upper edges of the flanks and in this case, the PSU is mounted to the top fan. Otherwise, the Assembly of the fan should be such that the PSU will draw air from inside the Cabinet.

• Replace the power supply for a Pavilion a140n

  How to install a new power supply in a HP Pavilion a140n? Is there a step by step guide?

  Zz30fg, welcome to the forum.

  Is the model you list correct?  I can't find anywhere.

  Before you start, I suggest that you measure existing power supply unit (PSU) to make sure that the one you choose to insert in the space provided.

  The first thing you will do is turn off the computer.  Disconnect all devices that are connected, for example, keyboard, mouse, printer, etc.  Once done, remove the side cover of the case.  There are two or more screws on the back of the computer that you have to remove.  Then slide the side gently to the rear.  Put it somewhere safe.   Be sure to touch the metal inside of the case before touching any components.  This will eliminate static electricity (ESD).  Now you can disconnect the cables from the PSU.  This is where it gets a little tricky.  I normally take a picture of the connections and mark them as clearly as possible on the motherboard.  Believe me, you'll be much happier if you do.  Once this operation is complete, it is time to remove the (4) screws that hold the power supply in place.  Hold it with care.  If it falls it can damage other components.

  The new power supply will be marked with the appropriate connector cables.  At this point, it's just the opposite of what you were doing to uninstall the existing PSU.  Install the power supply into the case.  Do not overtighten the screws.  Make sure that the cables are inside the case.  Once in place, carefully connect all cables to the appropriate connectors.

  If you have any other questions, I will watch this thread for you help.

  If your problem is solved, please click "accept as a Solution.

• How to replace the power supply VAIO VGN-CS115J?

  Hello

  The power cord on my VAIO VGN-CS115J computer works correctly, but the power supply on my is broken.

  How can I get my fixed Power Jack?

  Friendly greetings,

  Jussi Yrjänä

  Zealious,

  It seems you need to remove the bottom case at least to get access to the DC Jack.  You may need to remove more pieces to remove it.  The p/n DC Jack is A-1609-073-A and can be ordered through Sony parts @ 800-488-7669 (US models).