reset of the PXI-1000 b

Similar Questions

• How to reset the indicator of County of Terminal on the PXI-6608

  Dear community,

  Is it possible to reset the terminal number on the PXI-6608 indicator? When I use Get Attribute.vi I have the time to correct value first, but unfortunately (unlike DAQmx) reading of the value is not reset it...

  I like to keep track of how many times he flipped. And I don't want to use another counter to do because I like to keep them free for other things.

  Thank you!
  Case No.

  Traditional DAQ doesn't have a way to reset the indicator terminal number, as far as I know. One thing you might be able to do is change the "output" in "toggle" mode and then read the "output status" to determine the reversals to determine when the State of the output has changed in your application.

  I hope this helps!
  Gus...

• Trip trying to rearm with the pxi-5122 times

  Hi all!
  This is my first discussion in this forum so I'm not sure this is the right place to post, because I'm using LabView, but maybe it's a hardware problem.

  Then... I have a problem to calculate the tripping time rearm to pxi 5122.
  Compared to data sheets, I read that it should be about 3 us with the CDT to the large or 12 US if on.
  But I need a precise measurement of the time out after each record measured so I decided to find it by myself...
  With the help of an acquisition program that I have previous written in LabView, I started only acquisitions of 10000 records and each record is composed of 128 samples; as signal I've used waves square with different frequencies, 10 volts peak-to-peak (my trigger was set on the first channel of 5122 with 1 volt in value of edge).

  First acquisition: wave of 50 kHz. Theoretically, I s 0,2 need to capture 10000 records without losing all the square wave signals. Choose a time of acquisition for a single record of 15.3 us, I found that the time required is 0.199998 , very similar to the one expected.
  Then by choosing a time of acquisition for a single record of 15.4 us, I found approximately 0.4 s.
  I can guess that this latter one each tops of two waves will lost so I held twice the capture of 10000 records time.

  Because the wave is 20 us I calculated a timeout of 20-15, 3 = 4.7 us.
  It wasn't like the 3 described us for the 5122 but I was not impressed and I went with my essay.

  Second wave: 20 kHz. I need 0.5 s to capture 10000 records without losing the square wave signals.
  What I found was that in this case, choose us an acquisition time for one record of 39.6 required 0.5 s to capture all vertices, then with 39.7 us I held about 1 second, once again, twice by the time.
  The previous example, I calculated the dead time: 50-39, 6 is 10.4 us.

  Very strange... idle time I'm supposed to be the trigger for rearmament (and thus fixed) did not differ in 2 cases.
  Tried with other wavelengths, the values are always different.

  This also the frequency of the square wave of fixing and changing the number of samples per record.
  For example, with 128 samples per files as I told before, I needed a measurement time of 15.3 US to collect all the consecutive summits, while 64 samples I need 12.8 us and so forth.

  So it seems to be a dependency between the dead after a record time (the trigger reset? now I'm not sure if I can call it that) and the sampling frequency of the pxi 5122.
  But I don't know why, the acquisition of data behave in this way.

  Is this good? Rearm time should be set, shouldn't it?

  I know it took some time to read my problem but I tried to be more precise, I could.
  Thank you in advance.

  Giacomo

  Yes that's correct.  However, I do not think that its acceptable rate of the nearest synchronization that is chosen.  I really think he goes to rate lowest according to acceptable timetable.  So, if a synchronization rate is 2 and another is 5, and you want a 4.9uS rate, the synchronization will be 2, while 5 is the closest.  (Or maybe it's the other way around)  That's why you see the double period during the change of rates by just a fraction.

• Problem with the PXI-6534 elimination change detection task

  I ran into the following problem.  I use a PXI-6534 and PXI-6602 with vb.net for detection with a timestamp of changes.  My code works fine and I get data exactly as I want, the problem comes when I try to call the task.dispose function.

  When I call him has, she throws an exception with error-200088 code, task does not exist.  But the task is still stopped and I can run my code again and everything works fine.  If I do not call the task.dispose, I get an error when I try to run my code again.  The material seems to have left in an unknown state, and I have to restart my computer to get it back. (the MAX NOR even reset the 6602, he says only that the Council does not exist).

  Interesting also is the exception thrown does not seem to be caught by the Try Catch method.  The code traverses the Try Catch without any problem (step by step in the code anyway), but with the exception, the message box appears, either immediately or when coming out of the subroutine.

  Also, I use TestStand 4.2 to call these functions, if that makes a difference.

  Any help would be greatly appreciated!  Its very frustrating that everything works and I get my data perfectly, but I can't run the code without exception popping up, and I can't seem to catch the exception.

  Here is the code I use:

      Public Sub StartChangeDetect_UUT1()
          If myCDrunningTaskA Is Nothing Then
              Try
                  ' Create the task
                  uut1ChangeDetectTask = New Task()
  
                  '************************ Create the digital input virtual channel alias
                  'Assign ports to digital virtual channel
                  uut1ChangeDetectTask.DIChannels.CreateChannel("Dev1/port0:3", "ChangeDetectUUT1", ChannelLineGrouping.OneChannelForAllLines)
                  'uut1ChangeDetectTask.DIChannels.All.DigitalFilterEnable = True
                  'uut1ChangeDetectTask.DIChannels.All.DigitalFilterMinimumPulseWidth = 0.000001
                  uut1ChangeDetectTask.DIChannels.All.InvertLines = True
                  uut1ChangeDetectTask.DIChannels.All.DataTransferMechanism = DIDataTransferMechanism.Dma
  
                  'Assign ports to monitor for change detection, both rising and falling edges
                  Dim rising As String
                  Dim falling As String
  
                  rising = "Dev1/port0:3"
                  falling = "Dev1/port0:3"
                  uut1ChangeDetectTask.Timing.ConfigureChangeDetection(rising, falling, SampleQuantityMode.ContinuousSamples, 4000000)
  
                  'export change detect event to PXI backplane so we can get timestamps from timer.
                  uut1ChangeDetectTask.ExportSignals.ChangeDetectionEventOutputTerminal = "/Dev1/PXI_Trig0"
                  uut1ChangeDetectTask.ExportSignals.ChangeDetectionEventPulsePolarity = ChangeDetectionEventPulsePolarity.ActiveHigh
  
                  'uut1ChangeDetectTask.Stream.Timeout = 20000
  
                  ' Verify the Task
                  uut1ChangeDetectTask.Control(TaskAction.Verify)
  
                  ' Set up the data table
                  Initializeuut1DataTable()
  
                  ' Create the readers for the DI and the CI
                  uut1ChangeDetectReader = New DigitalSingleChannelReader(uut1ChangeDetectTask.Stream)
  
                  uut1CDCallback = New AsyncCallback(AddressOf uut1ChangeDetectCallback)
                  uut1ChangeDetectReader.SynchronizeCallbacks = False
                  ' Set up our first callback
  
                  uut1ChangeDetectReader.BeginReadMultiSamplePortUInt32(-1, uut1CDCallback, uut1ChangeDetectTask)
                  myCDrunningTaskA = uut1ChangeDetectTask
  
                  'Set up Timer for time stamp
  
                  uut1TimeStampTask = New Task()
                  '****************set up PXI-6602 timer to get buffered change events.  ie capture timer output on  the PXI_Trig0
                  'we can then correlate this timer capture buffer to the change detect buffer to get the time stamps
  
                  uut1TimeStampTask.CIChannels.CreatePeriodChannel("Dev5/ctr0", "TimeStamp1", 0.0000001, 0.02, CIPeriodStartingEdge.Rising _
                               , CIPeriodMeasurementMethod.LowFrequencyOneCounter, 4, 4, CIPeriodUnits.Seconds)
                  uut1TimeStampTask.CIChannels.All.CounterTimebaseRate = 20000000.0
  
                  'Use exported change detect from 6534 board to take counter sample
                  uut1TimeStampTask.Timing.ConfigureImplicit(SampleQuantityMode.ContinuousSamples)
                  uut1TimeStampTask.CIChannels.All.PeriodTerminal = "/Dev5/PXI_trig0"
                  'uut1TimeStampTask.CIChannels.All.DuplicateCountPrevention = False
                  uut1TimeStampTask.CIChannels.All.DataTransferMechanism = CIDataTransferMechanism.Dma
  
                  ' Set timeout
                  'uut1TimeStampTask.Stream.Timeout = 20000
                  ' Verify the Task
                  uut1TimeStampTask.Control(TaskAction.Verify)
                  uut1TimeStampReader = New CounterReader(uut1TimeStampTask.Stream)
                  uut1TSCallback = New AsyncCallback(AddressOf uut1TimeStampCallback)
  
                  uut1TimeStampReader.SynchronizeCallbacks = False
                  uut1TimeStampReader.BeginReadMultiSampleDouble(-1, uut1TSCallback, uut1TimeStampTask)
                  myTSrunningTaskA = uut1TimeStampTask
  
              Catch exception As DaqException
                  ' Display Errors
                  MessageBox.Show(exception.Message)
                  uut1StopChangeDetection("C:\PT3771\TestResults\")
              End Try
          End If
      End Sub
  
      Private Sub uut1ChangeDetectCallback(ByVal result As IAsyncResult)
          Try
              'If runningTask Is ar.AsyncState Then
              If myCDrunningTaskA Is uut1ChangeDetectTask Then
                  ' Read the available data from the channels
                  Dim data As UInt32() = uut1ChangeDetectReader.EndReadMultiSamplePortUInt32(result)
  
                  Dim b As UInt32
                  For Each b In data
                      ' in TestData waveform Y axix is data, x axis is time 
  
                      uut1TestData.SetY(uut1ChangeDataIndex, b)
                      uut1ChangeDataIndex += 1
  
                  Next b
  
                  '' Set up a new callback
                  uut1ChangeDetectReader.BeginReadMultiSamplePortUInt32(-1, uut1CDCallback, uut1ChangeDetectTask)
              End If
          Catch exception As DaqException
              ' Display Errors
              MessageBox.Show(exception.Message)
              uut1StopChangeDetection("C:\PT3771\TestResults\")
          End Try
      End Sub 'DigitalCallback
  
      Private Sub uut1TimeStampCallback(ByVal result As IAsyncResult)
          Try
              'If runningTask Is ar.AsyncState Then
              If myTSrunningTaskA Is uut1TimeStampTask Then
                  ' Read the available data from the channels
                  Dim data2 As Double() = uut1TimeStampReader.EndReadMultiSampleDouble(result)
  
                  ' in TestData waveform Y axix is data, x axis is time
                  Dim b As Double
                  For Each b In data2
                      uut1TimeSum = uut1TimeSum + b
                      uut1TestData.SetX(uut1TimeStampIndex, uut1TimeSum)
                      uut1TimeStampIndex += 1
                  Next b
  
                  ' Set up a new callback
                  uut1TimeStampReader.BeginReadMultiSampleDouble(-1, uut1TSCallback, uut1TimeStampReader)
  
              End If
          Catch exception As DaqException
              ' Display Errors
              MessageBox.Show(exception.Message)
              uut1StopChangeDetection("C:\PT3771\TestResults\")
          End Try
      End Sub 'CounterCallback
  
      Public Sub uut1StopChangeDetection(ByVal location As String)
  
          Try
              If Not (myTSrunningTaskA Is Nothing) Then
                  uut1TimeStampTask.Dispose()
                  myTSrunningTaskA = Nothing
  
              End If
  
              If Not (myCDrunningTaskA Is Nothing) Then
                  uut1ChangeDetectTask.Dispose()
                  myCDrunningTaskA = Nothing
  
              End If
          Catch ex As Exception
              MessageBox.Show(ex.Message)
          End Try
  
          uut1TestData.UpdatePointCount()
          uut1TestData.SaveToDisk("C:\PT3771\TestResults\uut1TestWaveFile.csv")
          uut1TestData.SaveToDiskBinary("C:\PT3771\TestResults\uut1TestWaveFile")
      End Sub 'StopTask
  

  Joe,

  Last updated.  It seems that when the task.dispose is run, recalls seem to have called one last time.  I took the call to the stopUUT1ChangeDetect in the two recalls (so eliminate it would not enforce a second time), and no exception was thrown.

  Thanks for your help!  Although if you'd still answer my question on the PXI-6534 Digital input filtering, I'd appreciate it.

  Thanks again.

  Thad

• Change in gain on the PXI-6221

  Hi all

  I apologize in advance for a newbee question. I recently started to work on the measurement of force in the laboratory of fluid mechanics. We got a load cell 3 - axis with 0.5 mV/V, power per channel, which I hung on SG24, which sits on SC-2345, connected to the PXI-6221.

  As far as I understand, after the signal comes out SG24 unit, it is amplified to 500mV and powered to PXI card, which in turn have 4 possible gains of 0.2V, 1V, 5V, 10V. To keep the resolution as fine as possible, I'd be interested take a +/-200mV gain, which in turn cut my signal more then half but keep a resolution ~ 6.1uV, I like not having the range, my forces expected fall shorter reach.

  The problem is that I can't find neither manual or MAX a way how truly change the gain. If I open MAX > NOR-DAQmx devices > PXI-6221, I see no possibility to change the input voltage. I can see +/-10V in the Test Panel, but if I change to +/-200 m it resets at + /-10, after I close and reopen again.

  Can someone help please on this issue?

  Thanks in advance

  Hi Chris,

  You made my day )

  Thanks a bunch!

• There is no conectivity with the pxi-8145 or. User1 witness stays on all the time.

  NI PXI-8145 connectivity has suddenly disappeared.  I tried to reset the IP address using the switch NORM/IPRST, but it is still impossible to detect the device.  MAX cannot detect it even if the workstation (PC) detects a network.  Also, USER1 light is all the time (and it's supposed to blink).  What I would do.  Is this a problem in map (PXI-8145) itself? or can be linked to the chassis (pxi - 1031)?  If there is no damage, what might have caused it? is there a Service Center for repair anywhere? How much would it cost?...

  K - lyn,

  The controller never worked properly?  Using FTP, look at the OR-RT/STARTUP folder (type ftp://x.x.x.x/ni-rt/startup in Internet Explorer, where x.x.x.x is the IP address of the controller).  What is there?  If you connect a monitor to it, something appears?  If so, what is on the screen?

  Your User1 light is constantly on.  The LED flashing sequence is documented in the manual on page B1.  Always on is not one of the choices.  When you power cycle the chassis, the controller starts with the LED User1, or it will Flash and then stay on?
  We can start from scratch by uninstalling the software on the controller and put it back.  To uninstall it, manually put the controller in safe MODE (switch S2 - see the PXI - 8140RT manual series pp. 2 - 6 and B-2 for more details).  Right now, starting with S2 switched uninstalls the software.  Switch to normal and then reconfigure the controller.

  What IP settings give you the controller? What version of LabVIEW Real-time using you? What drivers you put on the controller? What are the parameters of the host PC IP? What is in the program that you are using? You call dll or any C code?

• How to reset password HP mni 1000 wood

  Hello

  Can you please advise how to reset my password for the wood of the min 1000 hp laptop

  iI'm fatel error that I forgot the password

  Fatal error... System stopped

  [number of Series edited by Moderator]

  Thanks in advance

  Salim

  Try to SAL.

  e9lo1gf451 or e9lo1gfr51

  3rd letter tiny L.

  4th letter lowercase O.

  Use this code to go into the BIOS.

  Disable all passwords that are enabled.

  If demand for CURRENT password using this code.

  Request NEW password just press ENTER.

  If asked to hit just to CHECK password to enter.

  Save and exit.

  REO

  I must inform you that these services are not endorsed by HP, and that HP is not responsible for any damages that may occur to your system using these services. Please be aware that you do so at your own risk.

• When I click on the gear in modules to select Reset all the Add-ons to update manually, NO checkmark shows and firefox deletes icon Protection of Kaspersky

  I love the old version of Firefox, because I REFUSE to use my computer without Kaspersky. I have it? > Kaspersky is MORE important for me than Firefox (G.Chrome is my backup)

  Now I have KIS 2016 and I love its hexagonal icon, showing attempts it is blocking (it is set to block). Firefox 3 times now DELETED this icon, but shows that the Protection of Kaspersky is always an active add-in. I had to uninstall KIS 2016 3 times to return to this icon. When I click on the gear to select the background choice 'Reset all the Add-ons to update manually', nothing happens. No check mark shows, in Options / Advanced, I chose never "check updates". I'm tired of wasting my time to re - install KIS 2016 to get back on this icon. About: config I have enabled FALSE app.update.auto, app.update.enable and app.update.silent. What can be done in addition to the removal of Firefox? (I'm NOT going to install latest Firefox because it is incompatible with KIS).

  You are using a version of Firefox that is very old, please upgrade to the latest version of Firefox updated to the latest version. Kapersky drops support for older versions of Firefox, so if you do not update you may encounter problems in the strange, not to mention many security bugs in older versions of Firefox.

  Then, make sure that you use the latest version of Kapersky and then use controls, buttons and Toolbars Customize Firefox to add the icon of kapersky on toolbars of Firefox.

• My office has been reset to the factory settings. I am enrolled in my sync account, but my favorites that are on my laptop, did not came to the top. Now what?

  I was fortunately sync-ed a year betweem my computer laptop Mac iBook and desktop HP - a lot of bookmarks - I am a student. My office had a small problem and I got it clean and reset to the factory settings. I'm now creating upward. I installed Firefox and made Google my default search engine. Then I logged in sync - no problem (even email, password... I wrote it!) I clicked sync, but my favorites are not come to the top. I closed Firefox and re-opened, but still no bookmarks. I looked at the settings and everything is checked. I wouldn't change anything. What Miss me? Thank you.

  Both devices use new synchronization and more importantly on Firefox 30.

  If you you don't need the synchronization of the former, and even if you use the same address as used for synchronization of the old all should operate under the new synchronization.

  I think that the new synchronization drops devices that have not synchronized within the past 21 days.

  Former site of Firefox Sync: new Firefox Sync https://account.services.mozilla.com/ site: https://accounts.firefox.com

• Help! Did a reset of the PRAM and downgraded OS, lost passwords, files, and records office and dock apps.

  I did a reset of the PRAM because my mac running weird and now everything has changed. All the files on the desktop disappeared, the apps on the dock as well, Finder looks different, some applications do not work because they are for older BONES. It seems that the OS has been downgraded. I left the game and cannot connect back with my Admin psswrd even if the allusion to the fact that I drove to this password. I have no xknow what to do and I lost a lot of projects becauae plugins I had are not installed.

  HELP Please!

  Restart with the hold Option key and see if the correct operating system is displayed.

  If this is the case, click on it and then select it in the pane of the system preferences Startup disk.

  If not and you have a backup, upgrade the computer to the most recent OS and restore files according to its needs.

  In the case of contrary and you do not have a backup, back up everything you can and then upgrade.

  (143474)

• every time I erase content and settings on my iphone 6 after reset at the start of my phone and after crossing the screen as Hello > select language > Connect wifi > my iphone doesnot ask me activation lock even if my unit is also found on

  every time I erase content and settings on my iphone 6 after reset at the start of my phone and after crossing the screen as Hello > select language > wifi connection > my iphone doesnot ask me lock activation that says that your iphone is connected with the old apple ID, please enter the id and password

  I always reset on find my optional equipment please tell me how to activate locking activation so that whenever I have factory reset my phone with finding my camera so my phone always ask an old apple and password

  I do not understand your question, but let me go with what I believe. Looks like you entered in iCloud and erased all the content and settings on the iPhone, and once you go by assigning back up again, you do not see something that you expect to see, for example, a request for an Apple ID. When you go through the installation process to select the language, etc., it must, at some point, ask you to identify yourself with your Apple ID. are you not see this?

  It would be better if you try to describe exactly what you do again. Also, without the help of any sign of punctuation, it is difficult to track everything you ask. Try providing the steps of what you do, and then what you see when you get to the point that you believe that something is going wrong. You mention both an old and new Apple ID, which is rather confusing.

• Cannot create bookmarks. New install, have disabled all extensions, tried safe mode and reset to the default values. Any help of any of these actions.

  Hello.

  Statement of the problem is very simple: Firefox won't create bookmarks.

  New installation with Mint 17. New generation of PC with Asus A58M-A/USB3 motherboard, AMD A4 6300 processor 4 gig memory stick.

  All Mint and Firefox packages are up to date.

  A new profile has been created for the test, Firefox has been started in safemode, purged and re-installed and reset to the default values. None of these actions have contributed.

  Here is the info according to the troubleshooting information in Firefox

  The application databases

  Name: Firefox
  Version: 33.0
  User Agent: Mozilla/5.0 (X 11; Ubuntu; Linux x86_64; RV:33.0) Gecko/20100101 Firefox/33.0
  Windows multiprocessing: 0/1

  Reports of incidents for the last 3 days

  All Crash reports

  Extensions

  Name: Mint search Enhancer
  Version: 1.0
  Enabled: true
  ID: [email protected]

  Name: elegant
  Version: 1.0.7
  Enabled: true
  ID: {46551EC9-40F0-4e47-8E18-8E5CF550CFB8}

  Graphics

  Description of the adapter: X.Org - Gallium 0.4 on AMD ARUBA
  Device ID: Gallium 0.4 on AMD ARUBA
  Driver version: 3.0 Mesa 10.1.3
  GPU accelerated Windows: 0/1 Basic
  Vendor ID: X.Org
  WebGL Renderer: X.Org - Gallium 0.4 on AMD ARUBA
  windowLayerManagerRemote: false
  AzureCanvasBackend: Cairo
  AzureContentBackend: Cairo
  AzureFallbackCanvasBackend: no
  AzureSkiaAccelerated: 0

  Important change preferences

  Browser.cache.Disk.Capacity: 358400
  Browser.cache.Disk.smart_size.first_run: false
  Browser.cache.frecency_experiment: 3
  browser.places.smartBookmarksVersion: 7
  browser.sessionstore.upgradeBackup.latestBuildID: 20141013200257
  Browser.Startup.homepage_override.buildid: 20141013200257
  Browser.Startup.homepage_override.mstone: 33.0
  dom.mozApps.used: true
  extensions.lastAppVersion: 33.0
  Media.GMP - gmpopenh264.lastUpdate: 1416067922
  Media.GMP - gmpopenh264.version: 1.1
  Media.GMP - manager .lastCheck: 1416067922
  network.cookie.prefsMigrated: true
  places. History.expiration.transient_current_max_pages: 80569
  plugin.disable_full_page_plugin_for_types: application/pdf
  privacy.sanitize.migrateFx3Prefs: true

  Important preferences locked

  JavaScript

  Incremental GC: true

  Accessibility

  Enabled: false
  Prevent accessibility: 0

  Versions of the library

  NSPR
  The expected minimum version: 4.10.7
  Version: 4.10.7

  NSS
  The expected minimum version: 3.17.1 Basic ECC
  Version: 3.17.1 Basic ECC

  NSSSMIME
  The expected minimum version: 3.17.1 Basic ECC
  Version: 3.17.1 Basic ECC

  NSSSSL
  The expected minimum version: 3.17.1 Basic ECC
  Version: 3.17.1 Basic ECC

  NSSUTIL
  The expected minimum version: 3.17.1
  Version: 3.17.1

  Experimental features

  What other information can I give?

  Thank you.

  Jim

  You can check for problems with the database places.sqlite file in the Firefox profile folder.

  • http://KB.mozillazine.org/Bookmarks_history_and_toolbar_buttons_not_working_-_Firefox
  • https://support.Mozilla.org/KB/bookmarks+not+saved#w_fix-the-bookmarks-file
  • Maintenance: https://addons.mozilla.org/firefox/addon/places-maintenance/

• Hi I have a problem to connect on wifi I have reset all the setting ang simultaneously press the home buttom ang poewr but not wrking buttom, I can't and on the router because I was on a public area as hotel thank you

  I have 5 16 g model A1428 phone

  FCC ID * A IC * A IMEI; ***

  I TRY TO OPEN MY PHONE TO CHANGE THE BATTREY AND REMOVE THE LCD CABLE TO CHANGE THE POWER ON SWITCH, BUT UP TO THAT ONLY TO REMOVE THE LCD SCREEN, I GAVE ALL MY BECAUSE IS DIFFICULT... WHEN I PUT I CAN NOT CONNECT TO WIFI.

  I TRY to RESET all THE SETTING or RESET or PRESS TOGETHER HOME BUTTOM AND POWER SWITCH ONLY MARKET THE ROUTER NETWORK I can't DO it BECAUSE it OF in CRUISE BOAT or in public space...

  Thank you!

  ALFREDFROMTAGBILARAN

  < personal information under the direction of the host >

  Please do the following and after each test to see if the problem is resolved - if yes, then you can omit the following steps - I tried to list them in ascending order of the effort at least on a Mac and / or an iDevice

  1. Check if the problem is related to a single device and if other devices connect normally-
  2. If the answer 1 is 'yes' - try to connect the device assigned to somewhere else if possible - coffee or the University
  3. Please see recommended settings of WiFi routers and Apple access points
  4. Perform a forced - restart cela do not delete or purge all data and allows to solve many problems - here is how - press and hold the Off / On Home button and at the same time for about 15-20 seconds, until the Apple logo appears. Allow normal startup upward.
  5. Settings - WiFi - < network name > - Click on forget network - do a restart forced 4 and then again add the network
  6. If home - reboot the router by unplugging it for 60 seconds (power) and the plug and reconnect - obviously, this step can be done in a public place like a cafe or airport or University. While you're there - make sure your router is working on the latest firmware (check manufacturer's website)
  7. Settings - general - reset - Reset network settings - remember to have very practical WiFi passwords because it erases the WiFi passwords
  8. If it is a new specific net device in your home - make sure that the router gives enough DNS for all numbers which must / wants a connection - stuff like the printer, Chromecast get overlooked - ask for more details on this so not sure option
  9. Backup the device to iTunes - restore as NEW (no backup) using iTunes - see if solves problem - if yes - restore backup
  10. An appointment of 'Genius' to an Apple Store, or select another authorized service provider.

• I had a problem with slow, so I used "reset". The popup ran forever so I stopped it. Now I can not remove or add the program.

  I had a problem with slow, so I used "reset". The popup ran forever so I stopped it. Now I can not use, remove or add the program. How should I proceed?

  TIA,
  BWSwede

  Try to create a new profile.

  See "create a profile":

  • https://support.Mozilla.org/KB/Profile-Manager-create-and-remove-Firefox-profiles
  • http://KB.mozillazine.org/Standard_diagnostic_-_Firefox#Profile_issues

  If the new profile works then you can transfer files from a profile in the new profile, but make sure not to copy corrupted files.

  • http://KB.mozillazine.org/Transferring_data_to_a_new_profile_-_Firefox
  • https://support.Mozilla.org/KB/recovering+important+data+from+an+old+profile

  What problems do you have that you want to reset Firefox?

  Firefox creates a new folder of old data of Firefox on the desktop?

  If reset you Firefox and a new profile is created and some of your data (bookmarks, passwords, cookies, form data) is automatically imported and your current profile will be moved on the desktop (old data of Firefox).

• Writing math graphically with the TX 1000

  I need to be able to write handwritten mathematics in MS Office applications (or elsewhere).  I thought that I would be able to open PowerPoint and write on slides, but I can't get the TX 1000 to stop the recognition of writing and graphics just record attempt.

  Is it possible to do what I'm looking for?

  Thank you

  Donald

  I think you need to do is to write the equations in Windows Journal and save the pages. Install the Windows Journal Reader plug in for MS Office program (free download from Microsoft), then import the pages of newspaper into PowerPoint for presentation. If you are projecting the tablet on a screen, you can use Windows Journal as you plan to write on and he won't try to handwriting recognition.

  The log viewer:

  http://www.BrotherSoft.com/Microsoft-Windows-Journal-Viewer-download-62604.html