reset the cursor lists by program

Similar Questions

• There are no programs listed in the exception list allow programs and features in the Windows on Windows 7 firewall

  I try to add a program to the Windows Firewall exceptions list. When I go to control configuration\systeme and Security\Windows Firewall\Allowed programs, I discovered that there were not all of the programs listed.

  If I click on the "Edit settings" button, it becomes grey and nothing happens. I am the Admin so I should have access to it. When I click on the button "Allow another program", any program, I am trying to add will give me an error message saying "firewall cannot add Windows ' [program]" to the list of exceptions.

  This has happened recently. I was able to add programs to the list of exceptions before.

  Thanks for the reply.

  Run a place upgrade to repair your operating system

  How to perform an upgrade on the spot on Windows Vista, Windows 7, Windows Server 2008 & Windows Server 2008 R2
  http://support.Microsoft.com/kb/2255099

  Note: Before you perform an upgrade in-place, you must be prepared for the worst scenarios that led to your existing data on your computer being deleted. These data include data personal, settings, information about the hardware and software drivers. In case of a worst case scenario, you may have to reinstall all the programs. Make sure that you back up personal data to disks or other external storage devices before performing an upgrade on the spot.

  Please follow these recommended steps and post if you still experience the problem.

• If I'm totally off power to my PC, (storm in the region) to reset, the cursor appears, but will not move until I restart again.

  If I just powerdown (overnight), leaving a/c, connected, the cursor appears and moves, as my mouse moves.  HOWEVER, if I powerdown and completely disconnect the PC, 110V, to keep safe from one close shot of lightning, THEN the problem appears.  After the storm passed, I plug the PC into the 110 outlet, turn on the computer and restart it.  The cursor appears in the center of the screen, but it will not move when I move my mouse.  THE ONLY THING I can do is hit briefly, the power button to turn off the back and then click New to reboot (twice now)... then the cursor appears in the center of the screen and moves when I move my mouse.

  Yes, I still think it's the battery.  If the computer is turned off but still plugged into the wall, food always provides a small amount of power to the motherboard to keep a ready"" State.  In fact, if you stop it, but keep it is plugged, you can send a packet to 'Wake-on-LAN' through the Ethernet that would then turn on your computer so you don't have to press any button at all.  This requires that some things are always under tension even when the rest of your computer is turned off.  Remove the plug from the wall removes this standby power and now the BIOS of your motherboard must hold his memory by falling back on the battery.

  HTH,
  JW

• Retrieving value of a conference call log and add call logs for a list of the calls list by program

  Hi all

  I want to add programmatically call logs in the call logs list, I want to extract data from a ConferenceCallLog and based on the results I'm launching a new Normal call log, I fetch these data of ConferenceCallLog callDuration, callStatus, participating, notes, date. Here is my code for this:

  {} public void callLogAdded (CallLog callLog)

  If (callLog instanceof ConferencePhoneCallLog) {}
             
  ConferencePhoneCallLog newLog = callLog (ConferencePhoneCallLog);
  callType int = PhoneCallLog.TYPE_PLACED_CALL;
  int callDuration = newLog.getDuration ();
  callStatus int = newLog.getStatus ();
              
  PhoneCallLogID participant = newLog.getParticipantAt (0);
  String notes = newLog.getNotes ();
  Date date = new Date (callLog.getDate () .getTime ());

  try {}
  Thread.Sleep (1000);
  New Thread (new Runnable() {}
  public void run() {}
                        
  phn.addCall (new PhoneCallLog (date, callType, callDuration, PhoneCallLog.STATUS_NORMAL, participants, notes));
  }
  ({. start()});
  } catch (InterruptedException e) {}
  Generative TODO catch block
  e.printStackTrace ();
                 
  }
  }
  }

  but the call log has not added to the national list of newspapers. Please help me

  Turn on logging to the listener method. If it is run?

  If so, put the same code of your screen there. It runs?

  go step by step until you encounter something does not

• script to prevent the cursor from tab on if the format is incorrect

  Hi all

  I have the following script on the exit event of a field on my form I design, and basically if the format is wrong it must reset the cursor to the field unless the correct format is entered. Here is the Code:

  If

  (this.formattedValue<>YYYYMMDD) { }

  xfa.host.setFocus ("Last_Name5");

  }

  For some reason it isn't working and I wonder if someone on this forum will know why.

  Thank you

  LP

  have you tried to use a model of 99999999 {num field validation?

• Sections black in the list of bookmarks when you move the cursor over the list.

  When I click to open the list of bookmarks and then move the cursor to the list I have sections of the list blackened, although the position of the slider is not blackened fortunately.

  I tried uninstall and reload, firefox restart Firefox, but nothing seems to help.
  Help please.

  Start Firefox in Safe Mode to check if one of the extensions (Firefox/tools > Modules > Extensions) or if hardware acceleration is the cause of the problem (switch to the DEFAULT theme: Firefox/tools > Modules > appearance).

  • Do NOT click on the reset button on the start safe mode window or make changes.
  • https://support.Mozilla.org/KB/safe+mode

  Try disabling hardware acceleration in Firefox.

  • Tools > Options > advanced > General > Browsing: "use hardware acceleration when available.
  • https://support.Mozilla.org/KB/troubleshooting+extensions+and+themes
  • https://hacks.Mozilla.org/2010/09/hardware-acceleration/

• In "Add/Remove Programs" he has no option to remove when a program is selected in the populated list?

  I can see all of the programs listed in Add/Remove Programs option in the control panel.  When I select a program in the list, there is no option to remove / uninstall the program.  I tried a lot of programs and none give me the option?

  Hello
   
   
  Method 1.
  Reregister the install and check engine.
  a. Click Start, click Accessories and then click command prompt.
  b. at the command prompt, type the following and press ENTER after each line:
   
  MSIExec /Unregister
   
  MSIExec/regserver
   
   
  Method 2.
  Check if you can in safe mode. Note: you will not be able to uninstall programs in safe mode. It's just to check if you can.
  a. refer to the article below for the procedure safe mode in Windows XP
  A description of the options to start in Windows XP Mode
  http://support.Microsoft.com/kb/315222

  Method 3.
  It seems that there is a background app that launches the installer of Windows. We can perform a boot minimum troubleshooting to find the same thing. You need to perform a clean boot to find the program that is causing and then disable or remove.
  How to configure Windows XP to start in a "clean boot" State
  http://support.Microsoft.com/kb/310353/en-us
  Note: When you are finished troubleshooting, follow the steps as explained in the article to reset the computer to start as usual.
  
  Method 4.
  See also the steps listed in the article below.
  How to troubleshoot issues that may occur when you install, uninstall, or upgrade one program on a Windows computer
  http://support.Microsoft.com/kb/2438651/en-us
   
   
  I hope this helps.

  Thank you, and in what concerns:
  Shekhar S - Microsoft technical support.

  Visit our Microsoft answers feedback Forum and let us know what you think.
  If this post can help solve your problem, please click the 'Mark as answer' or 'Useful' at the top of this message. Marking a post as answer, or relatively useful, you help others find the answer more quickly.

• Updated FF version 33.1, now see the on list of computer programs 33.0.3 AND 33.1 versions is this normal?

  Have never seen two downloads of Mozilla browser at the same time on the list of computer programs. 33.0.3 display 77.4 MB size while 33.1 has blown up to 155 MB. Ironically, that 155 figure is basically 77.4 multiplied twice... Two browser downloads on the list of programs at the same time - eh?

  Update, 31.1.1 released (fixed bug 1021265)

  Thank you

• Apple Mail pop up when turning on the computer even if there is no list of programs inside.

  Hello

  I read the instructions how to rid mail pop up of thing. but when I checked my computer in the login items... There is no list of programs in there so I tried to add the mail about it and remove it. then I tried to restart my computer, but when I open my mac pop mail again. What should I do to stop this? Please help me

  Thank you

  Concerning

  -Maureen

  This popup you speak, you are not clear.

• Since a recent issue of app updates on my iPad a applications - Gummy Drop mini disappeared and there seems to be no update in my update of the applications list or I can delete. I tried a reset nothing helps. What can I do? Thank you very much. Steve.

  Since a recent issue of app updates on my iPad a applications - Gummy Drop mini disappeared and there seems to be no update in my update of the applications list or I can delete. I tried a reset nothing helps. What can I do? Thank you very much. Steve.

  Not quite sure what "disappeared" means. You can try to remove and re - download.

• Reset the program in MainStage 3.2.3 numbers

  Hello!

  I use the latest version of MainStage on the latest version of Mac OS X El captain as well.

  I'm having a problem when I want to reset the progressive values program change numbers.

  The real function in the works of MainStage, but once the program changes have been reassigned, MainStage is unresponsive to changes in my controller patch.

  If I manually change the program numbers, MainStage then responds.

  In the midi window, I can see that the patch change information are sent to the MainStage but without some form of response from the program.

  Anyone else having this problem?

  How can I report it to apple?

  Best regards

  I can't help you with the problem you are having, but you can provide your feedback directly to Apple via the menu drop down Mainstage. They can or not to respond, but all feedback is apparently verified; I was contacted twice over the last 6 years after the filing of comments on bugs.

• The cursor position can go beyond the limits when programmed with change of position

  I have the VI joint that has 2 buttons on it to move the cursor right and left of an increment when pressed.  (The code works when I replace with another chart of mixed signals with the same data as this one).  For some reason, the cursor will move beyond 608 to 613 to the right and the left.  I have the shows all the parcels market, but it doesn't seem to affect the thing.   Any ideas as to why this is happening?

  I have not studied in detail what is happening in your case, but as the sliders are locked in patches, it seems more reasonable to use the property "cursor index. It sets the index position of the table data where the cursor is locked. Seems to work very well (and without all this only convoluted songs and dances with cursor lists and names of labels).

  Try this:

  

  (I also highly recommend to stay away from coloring Easter egg from the diagram. A Boolean is hard to see on a green background. There is not a single background color that does not interfere unless a color yarn. Don't try to be cute, to focus on the task of encoding instead.

• create the new file option in Windows - how to add Notepad in the list of programs

  When I'm in a particular folder, I can right click and choose new... to create a new file in this folder.  The usual programs are available to choose from, such as Word and Excel, and also a few programs that I have installed are also available.  How can I add Notepad to the list of programs offered at the "create new file" with?

  Thank you.

  Except if you have changed the file association "New text Document" is Notepad.

  John

• Windows XP Add Remove Programs opens, but the list of programs will not appear?

  Windows XP Add Remove Programs opens, but the list of programs will not appear? Can check the programs add and romove, but when the next screen appears to list all installed programs nothing happens, it just says: waiting will list is bieng prepared, expected 15 minutes still nothing, never had this problem before. Thank you

  Alas...

  As the forums MS Answers does not prompt for any information system when a new question is asked, we know absolutely nothing about your system.

  Not knowing the basic information a problem prolongs the frustration and the agony of these issues.

  Click Start, run and enter the following command:

  regsvr32 appwiz.cpl

  Click OK and you should see a message like this:

  DllRegisterServer in successful appwiz.cpl

  Restart and see how things look now.

• How to reset the default mail program? When I click to send e-mail to a box of 'Contact us' site web or excel sheet spread with addresses e-mail, a new msn email opens.

  How to reset the default mail program? Got msn.com. Now, I went to q.com. When I click to send e-mail to a box of 'Contact us' site web or excel sheet spread with addresses e-mail, a new msn email opens. Now, I get an error message: rundll32.exe - bad Image, followed by a message the the appklication or the DLL C:\Program FIles\MSN\MSNSharedFIles\MAILMAPI. DLL is not a valid Windows image. Please check against oyur installatiion diskette. I have msn unisnstalled.

  I can access my e-mail through hotmail msn, but no linger to subscribe to msn premium.

  original title: default e-mail program

  Hi PAULKRISSEL,

  This function is not supported natively in Windows. You may may find a third of the program that will change the default to q.com.
  
  WARNING: Microsoft provides no assurance or warranty, implied or otherwise and is not responsible for the download you receive from the sites of third parties or support related to the download or the downloaded technology. If you need assistance dealing with third party technology, please contact directly the manufacturer.