Resolution of monitor and TV

Similar Questions

• Resolution with HP2311x and HP ProBook6455b series laptop monitor configuration problem

  Hello

  I have a problem-solving with portable HP2311x and ProBook6455b.

  Maximum resolution is 1024 x 768

  Current display driver is ATI Mobility Radeon HD 4200

  However, my HP monitor supports the 1920 X 1080.

  I used only the external monitor without using the laptop monitor and the maximum resolution is always 1024 x 768.

  I also downloaded the drivers recommended by HP, but it does not solve the issue.

  I also tried with the drivers provided by AMD, but I get still more low resolution (1280 x 768) because the driver software detects is ATI Mobility Radeon HD 4250

  When I try to use the AMD Vision Engine Control Center stops unexpectedly

  I have conteacted
  Portrait Displays, Inc..
  http://support.portrait.com

  But they suggested me to contact HP because they were not able to solve my problem.

  Any help will be appreciated.

  Kind regards.

  1. number and product name
  • HP ProBook 6455 b and HP 2311 x

  2 operating system installed (if applicable)
  • Windows 7 64 bit

  3. error message (if any)
  • No error message

  4. all changes made to your system until the problem occurred
  • No change

  Hello antgfig,

  Your ProBook is a business model.  Your question would better answer on the HP Enterprise Business Community Forum

  Good luck!

• Hi, im working with 2 1920 * 1080 monitors and you want to display a background thar image is on a resolution of 3840 * 1080 and I wanted to be half on each monitor. can u help me?

  Hi, im working with 2 1920 * 1080 monitors and you want to display a background thar image is on a resolution of 3840 * 1080 and I wanted to be half on each monitor. can u help me?

  Friday, July 20, 2012 14:35:27 + 0000, GastonBriatore wrote:

  Hi, im working with 2 1920 * 1080 monitors and you want to display a background thar image is on a resolution of 3840 * 1080 and I wanted to be half on each monitor. can u help me?

  Windows does not allow you this. However, you might be able to find a
  third party program that could do this.

  Ken Blake, Microsoft MVP

• monitor and TV resolution problem

  I have a computer connected to a monitor and a TV, using the configuration double monitor.  The problem I have is that when I put in place the TV and computer screen to display the same resolution, the icons on the computer screen are moving to a point approximately one inch above the bottom of the screen of the monitor.

  I can't have the icons to stay closer to the bottom of the screen, as they do on my other computer that has two computer screens.

  No idea what I can do about it?

  Have you tried setting the screen of the computer at its optimal resolution and the same thing with the TV? Chances are they'll be different. Check your TV manufacturers site to see what is best for your TV.

  I hope this helps.

• Different sizes of resolution between the Source monitor and program monitor

  Hi guys!

  Newbie here-sorry in advance. The size of resolution replaces my source monitor monitor of the program to the point where its very large in the program monitor and the image stays that way when exporting... What I am doing wrong?

  If all the clips are from the same camera, you make a new sequence that is correct, then put all your clips in it and change. You are simply based on this first clip sequence settings to lay the foundations for your project.

  If you have snippets of a few different types, such as 1080 p and 720 p, then you must decide on a workflow that suits your needs. If the final result must be distributed to 1080 p, you high-end 720 p content, but end result must be 720 p, better off to reduce the content in 1080 p. It depends on different factors.

  Thank you

  Jeff

• Bug in 2015 using two monitors and 6 K resolution Footage update

  After the update CC PP 2015 Ive notice a bug when I pull and extend a clip in my scenario, my second film LED 27 "monitor monitor which mirrors my monitor of the program just starts blinking and does not show the images rubbing as he used to. I extend the clip it does not reflect the correct position of the clip, it sparkles so that it shows my home desktop screen on occasion. Has anyone else been done to meet this bug. Its quite frustrating. This happens only when I have a second monitor hooked up. I've updated to version 9.0.2 they come out today. and I got the version 9.0.1 installed just F.Y.I before And I always feel the same questions. I am attaching a video and photo, so you can see the problem that is happening. After having tested far this only happens with images of 6 K resolution. It does not with a resolution of 4K and below. And again once this has happened after the update 2015 The photos of the show when I make drag and extend a clip in the program Monitor flashes and does not play the preview as it should, you can also see the timecode overlay is not correctly aligned either.  Password for the video: CCPP and I use a MacPro 2013 with 64 g ram duel D700 graphics cards and I'm editing a disc SSD of Raid Thunderbolt 2.

  
  

  I talked with Adobe tech support representative and he had no solution for me. Adobe can you please offer assistance more. Everything was good in Premiere Pro 2014 so it's probably a bug in update 2015 or conflict.

  
  

  

  Hi Azzie,

  After the update CC PP 2015 Ive notice a bug when I pull and extend a clip in my scenario, my second film LED 27 "monitor monitor which mirrors my monitor of the program just starts blinking and does not show the images rubbing as he used to. I extend the clip it does not reflect the correct position of the clip, it sparkles so that it shows my home desktop screen on occasion. Has anyone else been done to meet this bug. Its quite frustrating. This happens only when I have a second monitor hooked up. I've updated to version 9.0.2 they come out today. and I got the version 9.0.1 installed just F.Y.I before and I always feel the same question >

  I see that we have a solution for you on another thread. Locking this since it is a copy of the other thread.

  Thank you

  Kevin

• How to make a menu fit for salvation policies monitors resolution is larger and readable?

  How to make a menu fit for salvation policies monitors resolution is larger and readable?

  My UI elements appear tiny. | Error postal codes of Mylenium

  Mylenium

• Dynadock U10 & Satellite Pro U400 (video display resolution - main monitor)

  Hi all
  I want to put in place the video driver Dynadock see the external monitor as primary monitor:
  I have difficulty option 'Mirror', but I can't change the resolution: it is set at 1280 x 1024 but I see 1280 x 800 (as in the laptop monitor) with the large black bars on top/bottom of my screen (losing a part of my screen 19 '')
  I guess if Iget 'turn off' the netbook monitor and adjustment of the external Dynadock monitor as primary monitor, I would see fine at maximum resolution (in the same way as if I connect the external display on the laptop VGA port: it works fine)
  Any suggestion?

  Thanks in advance!

  Hello januan,

  If you set the 'mirror' mode, you would have the same resolution on the external monitor, the internal display.
  In this mode you cannot set a resolution higher on the monitor station on the inside.

  If you set "extend mode", you can set different resolutions.

  You have installed the latest driver for display link?
  From this page you can download and install: http://www.displaylink.com/support/downloads.html

  Best regards

• Non - generic pnp on the 2nd monitor and no sound

  Original title: generic Non - pnp on the 2nd monitor

  • 2 monitors... Left (23 1/2 ")... Law (21 1/2 ")
  • ........................................ DYNEX... AOC ENVISION series
  • The two usually run on 1920 x 1080
  • With the help of the ATI Radeon HD 5700 series
  • Both using VGA adapters convert
  1. Turn it on one day and the resolution is all screwed up after using an Xbox on the AOC (AV HDMI cords don't transfer sound for me)<---- might="">
  2. Cannot repair resolution of VGA resolution (?) (1600 x 900, 1440 x 900...) due to the generic Non-Plug-and-Play monitor.
  3. System Restore - nothing
  4. Drivers switch autour using AVG and other versions of Radeon. -fucking nothing but resolution
  5. Re-plug-nothing
  6. Defragmentation (desperate after 4 hours) - nothing
  7. Restart for the 100th time
  8. The computer stops at 'Starting Windows' screen and stops at halfway through safe mode.
  9. F8 F8 F8 F8 F8
  10. 'Repair your computer' - nothing
  11. Connect to the computer through Tablet and update all the drivers - back to step 2 of this ti time sometimes shows generic Non - pnp monitor and sometimes peripheral display watch on: laptop display even if my 2nd monitor displays and able to react to what I put on it.

  Monitor AOC is shifted from 3/4 "(black margin on the bottom) and an uncertain amount to the left (no right margin)."

  trying to be as helpful as possible, I have a lot of work to do and CS work is almost impossible for me without 2 monitors to work please help, thank you.
  UPDATE! : I had no sound.

  Mike,

  Disable the LogMeIn driver from Device Manager and check. There are a few reported issues where LogMeIn driver has disabled the aero thus also changed the screen resolution feature.

  -Click Start, and then press on and enter type Device Manager.
  -Double click on graphics cards to expand the video drivers.
  -Right-click on the LogMeIn mirror driver and then click on disable.
  -Restart the computer and see if that helps.

  You can try to uninstall the video drivers and then install the driver from the AMD website as given in my first answer.
  Note: it is there no trouble uninstalling the video driver. When the video driver is uninstalled, Windows starts with minimum VGA drivers. The resolution of the screen (icons on the screen) may look bigger, but after installing the latest video drivers, the screen resolution will be back to normal.

  Please try the following steps and answer results.

• U3014 monitors and Radeon HD 8570 will not display 2560 x 1600

  Monitors and video cards say they take in charge of 2560 x 1600. But there is no other choice for this resolution in the catalyst control center or the display settings. Windows 7 Enterprise 64-bit
  Graphics card: Radeon HD 8570 (should support 2560 x 1600 on two screens).
  2 ports DVI and Display Port display-> DVI (via an adapter).

  Fix.

  If my memory is good, the screen only comes with a dual link DVI and a miniDisplayPort to DisplayPort cable, but you can use the miniDisplayport on display and displayport on your GFX card connector and try again.

• Connection between the monitor and the Studio 1458 laptop seems broken

  After happily using my Dell Studio 1458 for a little over a year, all of a sudden my laptop screen went completely blank (not black, but a sort of grey empty) when I started yesterday. I have reset several times, I let it run and I heard the sounds of standard Windows startup. Since I assumed the laptop worked again very well, and I plugged an external monitor. I am now using the laptop with this external monitor and everything except the monitor to the laptop works very well.

  I can still go to "change screen resolution" and see the laptop screen correctly detected by Windows. I can turn it on by selecting "extend these screens. I can also change the screen resolution on the laptop screen. It's the same kind of gray white whatever I do. Of all this I conclude, there is nothing wrong with the drivers: the more likely culprit seems to be the link between the laptop and the screen of the laptop. Unfortunately I ran out of warranty three weeks ago so I don't know what are my options here. I started to disassemble the laptop to see if maybe I could plug a cable loose once more, but I got cold feet at halfway when I remembered that I had saved not properly all my files.

  Any ideas on how should I proceed?

  Thank you

  Johannes

  This would mean it's time to start trying new parts - cable first.  If that does nothing, try a new inverter (if the screen is CCFL).  If it's backlit by LEDS, try a new screen.

• Can I connect a Bluetooth monitor and bike cadence monitor simultaneously for 5 s iPhone

  Can I connect a Bluetooth monitor and bike cadence monitor simultaneously for 5 s (iOS 9.2) iPhone?

  Hi thepaulbarlow,

  Welcome to the communities of Apple Support! I'm sure we can help you with your question. In general, the iPhone should be capable of supporting multiple Bluetooth devices, as described in the following article:

  Manage the health data from multiple sources on your iPod touch, iPhone, or Apple Watch - Apple Support

  If you have any questions for matching one or the other device, you can find information and the steps in the following article useful:

  Get help to connect a secondary Bluetooth device with your iPhone, iPad or iPod touch - Apple Support

  See you soon

• Can I connect a VGA cable simultaneously with a DVI cable to a monitor and use the source switch?

  I found a similar, but not exact question and I was wondering if I could use the VGA cable AND cable DVI simultaneously on a HP 2159 m monitor and switch back and forth from analog and digital using the source switch on the screen? I noticed that some casual games such as found at BigFish and other gaming sites works best on VGA on DVI but I like to watch movies and other DVI instead of VGA?

  I did two HP 2159 m monitor but it could in fact be wise space more convenient to just use the right now and switch from the analog to the digital format.

  Thanks for any response.

  Hello

  You will need to edit the video in the monitor source selection when you want to switch.  Don't put it on AUTO.

  For a test, connect two monitors and then configure your PC for two monitors. Then, remove the monitor as the secondary (VGA) and now connect the cable to the main monitor VGA port.  Now try the video source selection in the menu of the monitor.  I never tried it on my 2159 m but it can work.

  Some monitors do not react to two active flows.

• I have my black getit monitor and the computer does not respound after 2 mnts when I start playing games online

  I have my black getit monitor and the computer does not respound after 2 mnts when I start playing games online

  Hello

  1. what operating system is installed on the computer?
  2. what web browser are you using to play the games online?
  3. don't you make changes to the computer before the show?

  If you use Internet Explorer, then I suggest you to try the steps from the following link:

  The problems of games online using Internet Explorer
  http://support.Microsoft.com/kb/2528246
  
  Additional information:
  Why my screen is black when I start Windows 7?
  http://Windows.Microsoft.com/en-us/Windows7/why-is-my-screen-black-when-i-start-Windows-7

  Solve game problems
  http://Windows.Microsoft.com/en-us/Windows-Vista/troubleshoot-game-problems

  The problems of the game performance
  http://Windows.Microsoft.com/en-us/Windows-Vista/fixing-game-performance-problems

  Troubleshoot display with Microsoft games
  http://support.Microsoft.com/kb/263039

• I can stream movies on my PC using the desktop PC monitor. But when I unplug the monitor and use a PC to TV HDMI cable I get the video but the audio now

  . Video streaming

  I can stream movies on my PC using the desktop PC monitor. But when I unplug the monitor and use a PC to TV HDMI cable I get the video but the audio now... Suggestions?

  Thanks for the file INF. I ck'ed for driver updates and I have the latest drivers installed.  I got the sound working on the TV by hanging the audio output of the PC to the entrance of the TV with the HDMI cable in place for video. It's the simplest solution to this problem, so I took it.

  By the way, I have a Dell 620 with windows 7.