restrict the SSID / VLAN to some AP?

Similar Questions

• How to limit the command "Reload" on some devices

  Hello, sorry for my English.

  We must limit the enforcement of the "Reload" command on some switches and routers considered basic or hubs.

  I could set up the limitation of the use of the command using the EEM, but I left out a 6500 switch, core of the data center, because the version of the operating system does not support the EEM.

  We have configured AAA and authentication on a GANYMEDE server where the users listed here (not local) to access devices.

  In fact, grant us permissions to run certain commands only via the "tac_plus.conf" file that resides on the RADIUS server.

  What I could not do is to restrict execution to "Recharge" by using the same method, but I was with EEM on the routers and critical switches.

  I would like to know if it is possible to restrict the command "reload" on some devices in the configuration instructions in the file 'tac_plus.conf'.

  Thank you very much.

  Hello

  I've never used in production another Ganymede except Cisco ACS server.

  However, on your tac_plus.conf, you can create profiles and refuse or allow certain commands. In this profile, you can do a deny "reload". Have you tried?

  It should looks like:

  Group = {Usercommand}
  by default the service allowed =
  cmd = no {}
  refuse to recharge *.
  ....."

  On the switch, I assume that you have configured the aaa authorization command?

  Thank you

  PS: Please do not forget to rate and score as good response if this solves your problem

• 2 SSID on the same Vlan?

  Hi all -

  Newbie question. When I set up wireless, I'll be able to use 2 different SSID on the same vlan?

  Example:

  dot11 ssid example1

  VLAN 2

  authentication open eap eap_methods

  authentication network eap eap_methods

  dot11 ssid example2

  VLAN 2

  open authentication eap_methods

  authentication network eap eap_methods

  Hi James,

  I hope that the attached material will answer your question:

  Cisco Aironet 1100 series

  Using VLANs with Cisco Aironet Wireless Equipment

  Obsolete versions of software Cisco Aironet permit binding multiple SSID to a VLAN. The current versions are not.

  http://www.Cisco.com/en/us/Products/HW/Wireless/ps4570/products_configuration_example09186a00801d0815.shtml#.

  Configuration Guide for Cisco IOS software for Points of access Cisco Aironet, 12.2 (15) JA

  Multiple SSID configuration

  VLAN id - vlan

  (Optional) Assign the SSID to a VLAN in your network. Client devices that associate using the SSID are grouped in this VLAN. You can assign one SSID to a VLAN.

  http://www.Cisco.com/en/us/products/HW/wireless/ps4570/products_configuration_guide_chapter09186a00802085c4.html

  I hope this helps!

  Rob

  Remember messages useful rate...

• restrict the vlan address mac

  Hello gentlemen, I bought a 48 sf300 and 4 VLANS.

  How can I restrict the mac address of the device can be connect each vlan? I just want to let macs for vlan, should join the pc to a vlan.

  Thank you very much!

  Pedro here is a document for port security.

  https://supportforums.Cisco.com/docs/doc-27720

  https://supportforums.Cisco.com/docs/doc-27753

  -Tom
  Please mark replied messages useful

• VLAN and the SSID does not not in the Web Interface

  We have a couple of APs which do not show the VLAN and via the web interface of AP SSID.  If you go to the SSID Manager page in the web interface, the page rises but doesn't show any SSID configured.  It goes the same for Services - Vlan.  This page appears but does not show in any VLANS configured.  If you telnet to the APs, you see the mssid listed and all the SSID interfaces.  The SSID on the access point is functional and working.  It is just so hard to use the web interface for these APs.  I tried to compare configs running on APs where the web interface does not show this and APs that it shows, but cannot see any differences.

  Thank you.

  Have you tried with different browsers?

  Nicolas

• Restrict access to the SSID

  Hello

  I set up a WLAN with WiSM2 controller installed on a 6500 Series, Aironet APs and ACS 5.3 for userauthentication 3600series. GBA is connected to Active directory so that users authenticate using AD (802.1 x is used and not a pre-shared key) on SSID A. I created a SSID B separated for guest users. I put restrictions on this SSID. Guest users are also created on the same ad where are born the internal users. How can I force users who are invited to connect to the SSID B and not be able to connect to the SSID? Currently, they can connect at the same time.

  Help, please!

  Sybille.

  You will need a way to distinguish users of your guests to "internal users". I guess that there is an attribute in AD which will allow to this

  Assuming that this is the case then add two new conditions to the authorization policy

  -Flag user/guest (suppose can get from AD)

  -called-station-id (RADIUS attribute). This attribute includes the SSID in the end

  Can then set the rules

  If flag user/guest is equal to 'Guest' and ends called-station-id-with "SSID" then< allow="" access.="" assign="">

  If flag user/guest is equal to 'Internal' and ends called-station-id-with "internal SSID" then< allow="" access.="" assign="">

  default rule would be to deny access

• Prevent students access the SSID with the school laptops

  Hi all

  I'm new to the network and I'm having a problem with the ACL.  My router is a RVS4000 that connects to a SG300.  The SG300 is in mode layer 3 and distributes to other sg300/200 that connect to multiple WAP321s. I have all configured for two VLAN, (10) public and private (1).  I need a way to keep my laptop student outside the public network for the purpose of monitoring.  I had hoped to do this with a mac-based acl, but I wonder if it's the best way, and if the ACL must be on WAP or the main switch.  All advice and/or assistance in writing the ACL would be highly appreciated.

  > wap321s cluster up to what it means when I apply the ACL to a unit, it will spread to others?

  Yes, it is the collection point - easier administration with configuration to all units instead of the configuration of per - WAP of multiplication. More on the features and benefits of the grouping of WAP, you can find here.

  But rather than use the ACL, I recommend to use filtering MAC (Wireless-> MAC filtering) for two reasons:

  • the administration if MAC filtering is easier than the ACL (this is a simple list where you put the MAC address you want to allow or deny). This feature is also designed directly to these needs that you have
  • with the help of MAC filtering you will prevent some laptops to connect to wireless networks - which means that these laptops will not connect successfully. But the ACL is designed for situations when you wanted to block some sort of communication for already connected clients.

  If you decide to use the MAC filtering, be sure to choose the option MAC Local filter inside the SSID configuration section.

• LWAPP access point not to advertise the SSID

  I have a 4402 WLC and LWAPP AIR-LAP1131AG-E-K9 connected to it.

  I've been struggling with the config for some time now.

  I have a laptop next to who will not see the SSID I configured it broadcast.

  I have no idea why, but I got the following errors in the log.

  APR 17 11:37:59.091 sim.c:913 SIM-3-GW_MISMATCH: MAC address of the 00:0f:f7:32:c1:80 GW received the JOIN query is different from the MAC addr 00:00 caching: 0C: 07:ac:64 of the Gw. removal of the address IP of Gw 10.45.50.97 for AP Mgr. & send ARP REQ. for resolv

  APR 17 11:37:49.080 spam_lrad.c:1107 LWAPP-3-DISC_INTF_ERR2: ignoring the discovery request received on one VLAN badly (70) on the interface mode LWAPP-L3 (1)

  I notice that the first error property intellectual GW-related, but I don't know if this is specified, and why it is inconsistent.

  I don't know what the second error means either on the VLAN evil.

  Please can someone help!

  Thank you very much

  Neil

  I saw this in HP laptops some time there and his call "LAN Switching".  By default, it is disabled on BIOS.

• How can I change the SSID to a Photosmart C4580?

  I browsed the forum and read some articles which none still worked. I use a Mac and spin the OS of Yosemite. In the sourse of trying to get the ro printer recognize the new router I have rest the factory default, so he now tells me that the SSID is hpsetup. How can I now change that to pick up the new router SSID?

  Hey Andy,

  You can try to enter the password in the section "WPA - PSK", instead of "WEP encryption" section, to see if it will work. It won't hurt to not test.

  Here are a few screenshots from another thread with someone who has the same issue which may help:

  Photosmart C4580 spend direct USB for iMac, wireless through Time Capsule

  If try your password does not work, you can try an application called Keychain, which can be used to retrieve wireless password, just to make sure that you use the same one.

  How to manage passwords with Keychain Access

  I hope that helps you

• Cisco Wireless - E2500 N Dual Band router and hide the SSID

  Hello

  I tried to hide my SSID by allowing emissions the SSID of the first, and then the other band.

  Once I have say-activated the SSID broadcast of the last band my laptop, which has the wireless card, would lose connection to the internet on reboot.

  I read somewhere, but now can't find the article, you can hide those SSID, but it requires some work to connect to a network that is more diffuse.

  Someone has knowledge on how to go about this, or maybe they could point me to a resource that explains how to set this up... thanks.

  Tom.

  The properties of the wireless network. Check "Connect even if this network is not broadcast".

• HP Officejet Pro 8100: change the ssid

  I recently tried the Hotspot to unite AT & T.  That has worked very well but not decided to take it and went back to my Airport base station and the old service provider.  When I tried to connect my printer to my network - a printer works fine but the HP Officejet Pro 8100 will not change back the Name (SSID) the name for the old SSID hotspot network.  Since I was a new AirBook Pro I have to connect the cable to a USB port and then run the utility for my printer and select network.  It does not connect.  Any suggestions?

  Thanks for your suggestion. I tried this many times and it would be not just to reset the ssid. So after writing my post, I tried pressing the wireless button and the on/off switch at the same time. I went to try out some other combinations and print the configuration page. He changed the ssid for the correct name. Of course then I had to do what you described. Go to the printer utility with the cable connecting the computer and the printer and click on network. It has finally connected and I unplugged the cable between the computer and the printer. No problems now. Thanks for responding so quickly and hope it helps someone else.

• SG300-20 - configure DHCP on the interface VLAN

  I have read the different partners of the discussions on the SG300 and SG500 going on regarding the high setting of VLAN and DHCP on VIRTUAL networks.  For some reason, I could not get even this simple task to work.

  First thing I did was update my version firmware and boot as follows:

  SW version 1.3.7.18 (date of 12 January 2014 time 18:02:59)

  Start the 1.3.5.06 version (dated 21 July 2013 times 15:12:10)

  HW version V02

  When I rebooted the SG300 after the SW/Boot updates the boot configuration has been crushed and I had to configure my switch from scratch.  The intention is to have two VIRTUAL networks:

  VLAN 1: all the devices, servers, etc.

  VLAN 2: subnet basis which distributes DHCP addresses

  The SG300-20 is connected to a router Asus RT-AC66U on the 192.168.1.x subnet and provides access to the internal network and WiFi access (IP address of the router is 192.168.1.1 and the default gateway).  Everything works without any problem.  So my task is simply to create 2 VLANS on 192.168.2.x subnet and use DHCP to assign addresses.  I spent many hours on it and I still can't get it to work.  When I connect a laptop to the port (GI8) assigned to 2 VLANS, I end up finding a few wobbly 169.254.x.x address.  I definitely thought something would not 'easy' that hard to set up, but apparently I was wrong.

  The SG300 is running in mode L3 as shown in my running-config below.

  Someone gets to see something which could prevent my client from the laptop to receive the interface VLAN 2 DHCP IP addresses that are not on the 192.168.2.x subnet?

  Any ideas / suggestions would be greatly appreciated!

  Here's my running-config:

  config-file-header
  MYSTICSW1
  v1.3.7.18 / R750_NIK_1_35_647_358
  CLI v1.0
  router adjustment system mode

  SSD of encrypted file indicator
  @
  SSD-control-start
  config of SSD
  control of password file unrestricted SSD
  no control of the integrity of the file ssd
  SSD-control-end cb0a3fdb1f3a1af4e4430033719968c0
  !
  database of VLAN
  VLAN 2
  output
  Add a voice vlan Yes-table 0001e3 Siemens_AG_phone___
  Add a voice vlan Yes-table 00036 b Cisco_phone___
  Add a voice vlan Yes-table 00096e Avaya___
  Add a voice vlan Yes-table 000fe2 H3C_Aolynk___
  Add a voice vlan Yes-table 0060 b 9 Philips_and_NEC_AG_phone
  Add a voice vlan Yes-table 00d01e Pingtel_phone___
  VLAN voice Yes-table add Polycom/Veritel_phone___ 00e075
  Add a voice vlan Yes-table 00e0bb 3Com_phone___
  Hello interface range vlan 1
  hostname MYSTICSW1
  host 192.168.1.15 record
  logging source hostname id
  username privilege 15 b4a0fcf20b2cd9d80a55b06ab8f83277f9733904 encrypted password cisco
  location of the SNMP-Server Office
  clock timezone ""-5
  DST Web recurring U.S. clock.
  clock source sntp
  unicast SNTP client enable
  unicast SNTP client survey
  survey of 192.168.1.10 SNTP server
  !
  interface vlan 1
  IP 192.168.1.254 255.255.255.0
  no ip address dhcp
  !
  interface vlan 2
  name MysticWAN
  192.168.2.254 IP address 255.255.255.0
  !
  interface gigabitethernet8
  switchport mode access
  switchport access vlan 2
  !
  output
  Default IP gateway 192.168.1.1

  Thanks in advance!

  Clint Lambert

  Clint, please see this post

  https://supportforums.Cisco.com/message/4178990#4178990

  -Tom
  Please mark replied messages useful
  http://blogs.Cisco.com/smallbusiness/

• Multiple SSIDs\VLANs, DHCP and wireless

  Hello

  Check out my last post in a different discussion.  I reported it as answered, my first question has been answered, but I am still confused of DHCP is working.  I work with a config along the lines of:

  I work with a WLC 5508.

  He'll be there 2 separate WLAN on their own VIRTUAL local area network.

  The WLC connects to the Southwest over a trunk link, which seems logical.

  However, my question is in connection with the TOUR to the switch... should be a trunk as well? (one answer, needs to be an access port)

  So my next question is:

  How clients in their ssid / VLAN respective will receive an IP via DHCP to it to the switch port that connects the TOWER on a VLAN?

  Here are the basics of my config.

  Hatch 192.168.1.55 Mgmt iface and 56

  VLAN 9 is going to be for tours only (network 192.168.9.0/24)

  VLAN 6 is for example personal WLAN SSID is CORP-WLAN (network 192.168.6.0/24)

  8 VLAN for the guests, example SSID is GUEST-WLAN (network 192.168.8.0/24)

  I have DHCP pools configured for each network, and 43 is set for the APs over the nearest SW to the WLC (the SW there rising directly)

  I have a dynamic port configured on the WLC, and two wireless LANs are associated with the port and have received their VLAN respective.

  Allows to say that I am an AP, I have tension, and given that my SW port is VLAN 9, my broadcasts DHCP is heard by the SW, and he assigned me an IP of the 192.168.9.0 pool.  It's all great.  Now, I have a client that tries to associate to my Guest-WLAN SSID, and is now applying an IP address... How can I assign an IP address from the correct pool?

  Maybe I'm too complicate it a bit...?

  In addition, lets say I have 3 pools DHCP configured network 192.168.6.0 24, 8.0, 9.0 on my way... How will the switch knows what pool to match with and VLAN individual?  I should know this, but I feel forgetful... SW needs to have an interface vlan is configured with an IP address that falls within a configured pool?

  Give me a sense, that is a good question?

  Bill

  There are several ways to solve your problem, it depends on your expectations. I guess that you will travel with the value default Local AP Mode.

  By default, it is important to note that customer traffic to a point of integrated access to the WLC, and then it comes out of the WLC on the VIRTUAL LAN that you specified. This is why the AP can be a switchport Mode access and could reside in a vlan / entirely different subnet of your wireless users.

  So assuming that it is the model that you want to track, a high level overview of the configuration would be as follows:

  Suppose you want client WLAN 1 VLAN 11 and WLAN 2 VLAN 12.  Assuming that the WLC management interface is VLAN 1.

  You simply need to create a dynamic Interface in vlan 11 and vlan 12 with the appropriate addresses. Then you would set up WLAN 1 out Interface VLAN 11 and 2 WLAN as output interface 12 VLANS.

  Now when a customer joins 1 WLAN, its traffic will be the tunnel from AP to the WLC via CAPWAP and going to the controller on VLAN 11. The client will now effectively be in VLAN 11.

  Who is?

• Binding of the SSID authentication

  Hi friends,

  It is a query of wireless LAN design.

  Components used

  1 WLC Version 5.0

  2. 1142 cisco access points

  3 cisco ACS 1120

  4 authentication: 802.1 x WPA.

  I'm radio 2 SSID named (VLAN 10) HR & ADMIN (VLAN 20) in all points of access. Wireless clients Gets the IP address using the DHCP server.

  The issue I'm facing when person ADMIN Select HR ssid, it uses its useraname / password and connect to the network and human resources able to access the resource

  So, how to prevent the HR person uses his user name password to connect to the ssid ADMIN. The ultimate goal is, same HR employee selects ADMIN ssid, it should not get network access.

  Please help me by sharing your valuable ideas

  Kind regards

  Sairam

  Hi Sairam,

  In the Radius access request, the WLC is including the following attributes (among others):

  Called-Station-Id: this should come in the form of "(nom dele de mac: BSSID:SSID WLC)"
  Airespace-WLAN-Id: this is the index of the WLAN through which the user connects

  So you could build an authentication (or authorization) rule in ACS that verifies if the Radius Airespace-WLAN-Id attribute has the same index as the SSID ADMIN (or Called-Station-Id contains the string "ADMIN") and, if so, and if the user belongs to the HR group (defined in ACS or AD, for example), only not authentication (or approval).

  Hope this helps,

  Fede

  --
  If this helps you or answers to your question if it you please mark it as 'responded' or write it down, if other users can easily find it.

• When to use the filter VLAN vs SVI-list of access on the switches?

  If VLAN 10 is a user of 10.10.10.0/24 subnet, VLAN and I want torestrict which servers can access these users in VLAN 10, I can configure an access list and apply the ACL of a VIRTUAL local network access plan or apply the ACL on the SVI "interface vlan 10. What is a good practice as much as when I use a VIRTUAL local network access plan and when I apply the access list directly to SVI?

  Thank you very much

  VLAN-access plans are used when you want to restrict the hosts in a vlan. If you have a server and host in vlan 10 and you want to restrict this host to access the server, you must use a virtual local network access card.

  On the IVR access lists are used when you want to restrict intervlan routing between VLANS. If you have a host in vlan 10 and a server in vlan 15, you would use a normal ACL applied to the svi vlan 10, restricting the host to access the server in vlan 15.

  HTH,

  John

  Please note the useful messages *.