Routing inter - vlan Sg300-28
Hello
Thank you and thank you in advance if you can help with this simple configuration
SG300, how can mode layer 3, you make 2 VLAN see each other?
In my lab at home:
Default Vlan1 (GE1: access mode) 192,168,2.254
Static VLAN10 (GE24: access mode) 192.168.10.1
Town of Port GE25: Trunk Mode directly connected to interface my router 192.168.2.1)
Vlan1 can communicate with the outside world and the internet, for example, to a different subnet: 192.168.1.0
VLAN10 is not visible from the outside and from VLAN1
How can I allow traffic from VLAN10 through the commune GE25 Port to the outside world?
The router config says: VLAN10 is diretly connected to 192.168.2.1, but I can't ping. I wonder why?
Concerning
Minh
--------------------------------------------------
VLAN #show SG300
Created by: D-default, S-Static, G-GVRP, R-radius assigned VLAN
Ports created by virtual local network name
---- ----------------- --------------------------- ----------------
1 1 article gi1-23, gi25-28, D m 1-8
10 gi24 S VLAN10
Ip #show SG300 road
Maximum parallel paths: 1 (1 after reset)
IP routing: enabled
Codes: > - best, C - connected, S - static
S 0.0.0.0/0 [1/1] via 192.168.2.1, 36:24:22, vlan 1
C 192.168.2.0/24 is directly connected, vlan 1
S 192.168.10.0/24 [1/1] via 192.168.2.1, 27:23:12, vlan 1
He had to set the default gateway on the switch to 192.168.2.1
-Tom
Please mark replied messages useful
Tags: Cisco Support
Similar Questions
-
No SG300-52 routing inter - VLAN
Hello
I have a base on this SG300-52 configuration:
- L3 is enabled
- Latest Firmware is installed (1.4.0.88)
- Vlan1 IP is 10.0.0.1/24
- A PC is connected to port 1 (with IP 10.0.0.3)
- VLAN99 IP is 192.168.0.2/29
- A router is connected to the 49 port (with the 192.168.0.1 IP address and Internet access to the router is OK)
- On SG300-52 default gateway is 192.168.0.1
The SG-300:
- I can ping the default gateway (192.168.0.1) and any Internet address, using 192.168.0.2 as address IP Source
- I can't ping the default gateway (192.168.0.1) or any Internet address, using 10.0.0.1 as address IP Source
- I can ping my PC (10.0.0.3), using 10.0.0.1 as the IP Source address
- I can't ping my PC (10.0.0.3), using 192.168.0.2 as address IP Source
There is no routing inter - VLAN, but I can't find how to activate...
The complete configuration is the following:
#show run SG300-52
config-file-header
SG300-52
v1.4.0.88 / R800_NIK_1_4_194_194
CLI v1.0
router adjustment system modeSSD of encrypted file indicator
@
SSD-control-start
config of SSD
control of password file unrestricted SSD
no control of the integrity of the file ssd
SSD-control-end cb0a3fdb1f3a1af4e4430033719968c0
!
database of VLAN
VLAN 99
output
Add a voice vlan Yes-table 0001e3 Siemens_AG_phone___
Add a voice vlan Yes-table 00036 b Cisco_phone___
Add a voice vlan Yes-table 00096e Avaya___
Add a voice vlan Yes-table 000fe2 H3C_Aolynk___
Add a voice vlan Yes-table 0060 b 9 Philips_and_NEC_AG_phone
Add a voice vlan Yes-table 00d01e Pingtel_phone___
VLAN voice Yes-table add Polycom/Veritel_phone___ 00e075
Add a voice vlan Yes-table 00e0bb 3Com_phone___
Hello interface range vlan 1
hostname SG300-52
username privilege 15 c464af817287343305cbd6493c593885695df531 encrypted password cisco
property intellectual ssh server
Server SNMP Server
The telnet server IP
!
interface vlan 1
the IP 10.0.0.1 255.255.255.0
no ip address dhcp
!
interface vlan 99
name WAN
IP 192.168.0.2 255.255.255.248
!
interface gigabitethernet49
switchport mode general
VLAN allowed switchport General add 99 unidentified
switchport General pvid 99
!
output
Default IP gateway 192.168.0.1You have an idea on the issue?
Thanks in advance for your help.
Hi Anthena1390
My email is [email protected] / * /. When you reply to the email can let me know which devices need to communicate on VLAN 99. Is there a major reason for SG300 happen DHCP assumes that your router? Well I would like to add a few screenshots, they will show you how to properly set up a P2p link, assign DHCP pools, how to correctly add default routes. Send an email and lets get your problem is resolved.
-
RV042G router - Inter VLAN:
Is this router supports 802. 1 q? Or do I have to connect to a router port by VLAN?
for example. If I have 2 VLANS configured on a SINGLE SWITCH, do:
(a) TRUNK VLAN switch and plug a port on the ROUTER?
(b) connect a port on the ROUTER to VLAN1 and another port to VLAN2?
Thank you
Henrique
Hello Henrique,
The RV042G is not compatible 802. 1 q Trunking, so you would need a VIRTUAL local network connection.
According to the switch, you may need to disable the tree covering both to make multiple connections to the same router work.
Hope that helps,
Christopher Ebert - Advanced Network Support Engineer
Cisco Small Business Support Center
* Please note the useful messages *.
-
Problem with routing inter - VLAN... How to solve it?
Hi all.
I have a WRVS4400N in my office to have a VPN with our main customer and also to manage the entire network of small size.
In two weeks, more or less we will change our office somewhere else, merge two in one.
At its new location, we will have two different ADSL connections, and we will keep our separate LAN to the other LAN.
The goal is to interconnect the two local networks in order to 'see' the machines on one local network to another, but keep the two local networks with their current configuration, subnet, etc..
To achieve this, I created a new VLAN on the router and I have attached only port4 to this VLAN.
As you can see, VLAN main has its own/24 subnet (10.148.145.0/24) and dhcp enabled (for addresses on my LAN) while the new VIRTUAL local network has its own 24 subnet too (10.0.0.0/24) but with the disabled dhcp (is a different LAN with its own DHCP server).
VLAN 1 use ports 1-3 and VLAN 2 use the single port 4.
Of course, I enabled routing inter - VLAN:
To emulate the future scenario, I connected a router with an Internet port 4 with IP:10.0.0.2, and I therefore two different local networks.
Well, the reality is this:
-From my PC connected to the VLAN1 I have an IP address (assigned by my Cisco) and I see all my VLAN and I see 10.0.0.1 too (IP of the router on VLAN2), but I don't see any more (pings to 10.0.0.2 didn't answer). I can access Cisco router to 10.0.0.1 and 10.148.145.97.
-My PC connected to the VLAN2 I have an IP address (assigned by the other router on 10.0.0.2), I see only my VLAN (10.0.0.0/24 IPs). I can access only Cisco router to 10.0.0.1.
How can I do to enable these two VLANS to 'see' each other?
How can I control access to the WAN port? I don't want machines to VLAN2 accessing internet through our router.
Thank you and best regards!
Hello Francisco,.
In router mode gateway mode switch will turn off the NAT on the router. Which will allow to the vlan 2 does not to get out to the internet but also vlan 1 and which is not what you want. You may be able to create access rules and deny rules for not being able to get out of the internet... may create some default of the rules of the road as 0.0.0.0. Also, you may be able to create internet air to stop a certain subnet that it is able to get out of the internet as well.
Regarding the VLAN talk to each other, everything looks good, routing inter - vlan, it is allowing the two VLAN to talk to each other and which is activated. What your default gateways are installed on devices you are testing? As long as default gateways on your PC and devices are pointing to the routers ip/gateway address, you should be good to go at this point.
VLAN 1: default gateway should be 10.148.145.97
VLAN 2: default gateway must be 10.0.0.1
Other than that everything seems to be implemented correctly based on the images. The VLANs that you put in place on the ports are correct.
Let me know your devices are configured on the rise and will go from there.
Hope this helps,
Thank you
Clayton Sill
-
Restricted Inter-VLAN with SG200-26 and SG300-10 routing
Hi all
My apologies if this has been covered elsewhere.
My organization would like to organize a LAN game activity. The installation program I have in mind involves a switch 24 ports to connect all computers in player and saw that the switch connected to a smaller 'core' which has the connected the router and game server. I would like to know if I can put things up as follows...
SG200-26 with 1 to 24 ports on VLANS separated so they can talk to eachother. I'd then ports 25 and 26 to be a trunk aggregated (for bandwidth and redundancy) port to carry all 24 VLAN more an additional management VLAN (VLAN 100 e.g.) that will be used to access the switch. I want these aggregated trunk ports to connect to a 'core' SG300-10 switch that is connected to the game server and a router for internet access.
I would like to than the possibility of having two network connections of the server to the switch, one on the management of VLANS and the other on a VLAN different (e.g. 50 VLAN) which will be accessible by players (ports 1-24 of SG200-26). The power switch needs to be able to perform routing inter - VLAN restricted, because it does not VLAN 1-24 of eachother talk but they can talk to VLAN server, but only through specific service ports (e.g. 12345, 12346 port). Is this possible?
Also how I configure the SG300-10 to enable the VLAN 1-24 of VLAN 50, but not to talk or VLAN 100. So, I will probably have the router on its own LAN VIRTUAL (VLAN 60 ex.) and allow for VLAN 1-24 for access, but only via HTTP port 80 for web access.
What do you think?
Thank you.
Hi Marc, the default gateway of the computers will be the SVI to the switch.
Router-> couche3-> SG300 layer 2 SG300
router is 192.168.1.1
VLAN 1 in 300 SG is 192.168.1.100
2 VLAN on 300 SG is 192.168.2.1
SG300 layer 2 has a 1u, 2 t trunk.
My computer to connect to an access port 2 unidentified on the layer 2 SG300.
I am able to ping 192.168.2.1
I am able to ping 192.168.1.100
I can not 192.168.1.1 pnig
The reason is that the router has no idea on this subnet so cannot send the package to the source 192.168.2.x subnet.
The ACL and the basic connection are 2 different animals. The ACL is to prevent intervlan communication. The basic connection must be tags trunk and vlan or static routes.
-Tom
Please mark replied messages useful -
Catalyst 6500 Inter-VLAN routing
I have a Cisco 6500 switch and I have a question about routing inter - vlan and the command "IP ROUTING". I use dial-up virtual interfaces (I.e. int vlan 2, int vlan 3, etc.), but I noticed that I don't have the IP ROUTING enabled on my switch but I can route properly between the VLANS. I have even a little ports that I have configured with the command "no switchport" and I assigned an IP address to these ports. On routed ports, there is another switch on the other side configured with an IP address and I am able to ping and route traffic to the other network.
I did some research on this and all the documentation I am able to find talk of how you must enable IP ROUTING to route between the VLANS. I guess that this should only be done if you go to the road to other not directly connected networks.
http://www.ccnpguide.com/CCNP-switch-642-813-inter-VLAN-routing/
Can someone clarify this for me?
For the 6500 Series, IP routing is enabled by default, that so all VLAN can communicate with each other. You don't need to activate as you do for other switches (IE 3560, 3750, 3850, etc...)
HTH
-
RV180 router: impossible to get Inter-VLAN routing to work.
I've been hit in this now for two days and just can't get Inter-VLAN routing to work on this router.
Here is the place is:.
Updated to the latest firmware of Cisco (1.0.1.9).
From default settings, I added 2 VLAN as follows:VLAN (id = 1) default: dhcpmode = port IP=192.168.1.1/24 from server 1
VLAN vlan2 (id = 2): dhcpmode = port IP=192.168.2.1/24 from Server 2
VLAN vlan3 (id = 3): dhcpmode = port IP=192.168.3.1/24 Server 3(without link)
WAN port
|
Routing/NAT
|
--------------------------------------
VLAN ip 192.168.1.1 192.168.2.1 192.168.3.1
name of VLAN by default vlan2, vlan3
VLAN id ID = 1 ID = 2 ID = 3
Inter-VLAN only routing Yes Yes
Excluded excluded unidentified 1 port
2 excluded excluded Untagged port
Port 3 unmarked excluded except
Port 4 (not interest) without excluded tag excluded
--------- -------- --------
1 2 3 Port port
| | |
AdminPC PC3 PC2
192.168.2.191 192.168.3.181PC2 is assigned an IP address of 192.168.2.191 (DGW = 192.168.2.1) - OK
PC3 is assigned an IP address of 192.168.3.181 (DGW = 192.168.3.1) - OK(IP 192.168.2.191) PC2 can ping 192.168.2.1 and 192.168.3.1 - OK
(IP 192.168.3.181) PC3 can ping 192.168.3.1 and 192.168.2.1 - OKBUT...
PC2 cannot ping PC3 - don't DO NOT WORK
PC3 can not ping PC2 - don't DO NOT WORK(does not work in gateway and router Mode)
CAN SOMEONE HELP ME UNDERSTAND WHY?
Your help is very appreciated.
I bought this unit specifically because she supported routing inter - VLAN!
Vlaminck
---------------------------------------------------------------------------
Support information:
Screenshots:
Belonging to a VLAN:
VLAN ID Description Inter VLAN device Port 1 Port 2 Port 3 Port 4
Routing Mgment
1 default disabled enabled unmarked excluded excluded unlabeled
2 active active VLAN2 excluded unmarked excluded excluded
Unmarked 3 VLAN3 active active excluded excluded excludedSeveral subnets VLAN:
VLAN ID IP address Subnet Mask DHCP DNS Proxy Mode status
1 192.168.1.1 255.255.255.0 DHCP Server enabled
2 192.168.2.1 255.255.255.0 DHCP Server enabled
3 192.168.3.1 255.255.255.0 DHCP Server enabledRouting table (Bridge Mode)
Destination Gateway Genmask Metric Ref use Interface Type flags
127.0.0.1 127.0.0.1 255.255.255.255 1 0 0 static lo upward, gateway, host
192.168.3.0 0.0.0.0 255.255.255.0 0 0 0 dynamic bdg3 to the TOP
192.168.2.0 0.0.0.0 255.255.255.0 0 0 0 dynamic bdg2 upward
192.168.1.0 0.0.0.0 255.255.255.0 0 0 0 static bdg1 to the TOP
192.168.1.0 192.168.1.1 255.255.255.0 1 0 0 static bdg1 upward, gateway
127.0.0.0 0.0.0.0 255.0.0.0 0 0 0 lo dynamicRouting table (router Mode)
(Ditto)
Hello
It's not because the pings are allowed on the same subnet that they come from a different subnet.
You probably have a firewall problem windows software because that by default, it removes a different subnet icmp echoes.
Concerning
Alain
Remember messages useful rate.
-
EMS 2010 routing problem inter vlan
OK, back to the base, I tried to install complicated things that did not work so now, I'm leaving the base.
I am trying to configure my SGE2010 48 ports Gigabit cisco / switch for routing inter - vlan.
so far, I put the mode switch layer 3 from the telnet console and rebooted, it.
entered the interface web and changed the ip of the vlan by default management 192.168.2.3
added the vlan 70 and vlan bridging 180, section of mangement of vlan
under the IP, IPv4 interface address, I've added the IP address for each virtual local area network as follows:
IP Interface Mask
192.168.70.3 255.255.255.0 VLAN 70
192.168.180.3 255.255.255.0 VLAN 180
then I went in transition, management of VLANs, vlan to the port:
set the port g1 get access to the vlan 70
sets the g2 as an access port for vlan 180
connected A computer to port g1 with static IP 192.168.70.200 mask 255.255.255.0 Gateway 192.168.70.3
connected computer B to port g2 with static IP 192.168.180.180 mask 255.255.255.0 Gateway 192.168.180.3
I'll then in the routing static routing: I see the 192.168.70.0 destination IP address 24 as a type of local railway and even for 192.168.180.0 24 as the type of local railway
on a computer, I ping the gateway 192.168.70.3 and it works
on computer B, I ping the gateway 192.168.180.3 and it works
problem is that they cannot ping each other, windows firewall is disabled on both computers.
If I do a tracert on any of the computer he reach the gateway by default but then expire on the second jump.
any suggestions what I could have done wrong and the solution to the problem would be appreciated.
Edit: Here's the running configuration if it helps:
Cisco-SGE2010 # show running-config
database of VLAN
VLAN 70 180
output
g ethernet serial interface (1.26)
switchport access vlan 70
output
interface ethernet g2
switchport access vlan 180
output
interface vlan 70
printer name
output
interface vlan 180
name wireless
output
interface vlan 1
IP 192.168.2.3 address 255.255.255.0
output
interface vlan 70
IP 192.168.70.3 255.255.255.0
output
interface vlan 180
IP 192.168.180.3 255.255.255.0
output
Cisco-SGE2010 hostname
location of the Server SNMP here
SNMP Server contact me
Cisco-SGE2010 #.
If you can test both the interface switches the routing works correctly. You need to maybe turn off the Windows Firewall or open the firewall to allow ICMP to a different subnet. Windows Vista and 7 by default will block ICMP from any other subnet then their own.
Cisco Small Business Support Center
Randy Manthey
CCNA, CCNA - security
-
Problem of trunking routing\802.1 Q inter - VLAN SGE2000P - Cisco 2821
I am to evaluate the EMS and is unable to get routing inter - VLAN to work on aid and the external router via a 802. 1 q trunk. I have a 2821 with 3 secondary interfaces and I use the VLAN 1 as the VLAN native. G0/0 on router is connected to the port of G1 to the port of the EMS. I can create a VLAN and devices in the VLANs can reach devices in their VLAN respective, but they can't get the router IP address to access the other subnets. Currently I have the port connected to the configuration of the router, as a trunk by using VLAN 1, which is not marked. The EMS has the latest firmware and I tried some types of access ports, general & trunk, changed the PVID, nothing has worked for the other ports on the switch. What would have taken two minutes on a Cisco Configuration switch left flabbergasted me, it could be a defective switch? I was not able to find documentation or examples of this configuration scenario.
For reference, config the router interface:
G0/0.1
encapsulation dot1q 1 native
IP 1.1.1.1 255.255.255.0
G0/0.2
encapsulation dot1q 2
2.2.2.1 IP address 255.255.255.0
G0/0.3
encapsulation dot1q 3
3.3.3.1 IP address 255.255.255.0
Any help\direction is appreciated.
Thank you
Burt
Burt Hello, good evening,
Have you included the VLAN 2 and 3 on the trunk port and ensured that they are labeled? It should be set to tagged. The Web interface can be confusing with this config / operation.
Please check this and let me know, and if necessary I'll lab this for you as well. Please let me know,
Andrew
-
RV220W Inter VLAN firewall rules
Hello
I just bought RV220W Cisco router for our branch to replace Zywall 2 Plus. Update to the latest firmware 1.0.5.8 device.
I tried several different setting, but can not solve simple inter configuration of VLAN, that ZyWall resolves in a few clicks.
I have a simple task: I need two VLAN isolated on my network (VLAN 1: 10.1.2.1 and VLAN10: 192.168.2.1). No movement between them VLAN is allowed. I have to configure several exceptions:
1.) access of VLAN1 to Server (192.168.2.40) from VLAN10 port 3389 (RDP).
2.) VLAN10 access to a network printer (10.1.2.10) on port 9100 VLAN1.
I tried several settings and configurations of firewall that does not work.
I tried inter VLAN (VLAN-VLAN) rules to block all traffic except permitted, but these rules don't change anything. I have full access to one VLAN to another and vice versa.
I tried to disable routing inter VLAN, which solve my task of isolation, but firewall interVLAN rules does not work for exceptions, I need.
Thanks for all your help in advance.
Hello
For this configuration, you must first uncheck InterVlan routing for both VLAN (network > LAN > belonging to a VLAN). Also make sure that the ports are propely configured-tag/Untagged/excluded
After that, he must create access rules 2 (Inter MELANIECARDENES (VLAN - VLAN))
-from Defaul to VLAN10 - always allow - Source all - Destination 192.168.2.40
-Since VLAN10 to Default - always allow - Source all - Destination 10.1.2.10
There is no need to create rules to block, as it is by default and interVLAN routing is not enabled.
If with this configuration you still do not have access to the server and printer, you can use Administration - diagnosis - capture the packets and Wireshark to track if the packets are routed properly through VLANs and where the string stops.
Kind regards
Bismuth
-
Routing between VLANS in one direction
OK... so I don't know if I can do this, but I'd like some input cases possible.
Network equipment - RV120W, SF300-24
VLAN10--> switch in VLAN, internet access - preferably just 3 addresses
VLAN20--> switch in VLAN, initiate connection with VLAN10, VLAN30, access internet (I realize that there is a risk to security, but inevitable)
VLAN30--> switch in VLAN can access internet
VLAN40--> Internet access only, can not pass
I the installation of circuits between the devices and assigns him VLAN quite easily, I'm not sure how (or if its possible) to create routing tables / settings to accomplish. I am not able to do this on a SF300, but some tips you would know - even if I accomplish only part of what would be ideal.
Hello Smith,
I suggest the creation of access list (ACL based IPv4) for your configuration (assuming you do your routing inter - VLAN on the switch). If you are routing inter - VLAN on the RV120W, you may need to create the list of access on the router instead.
See the article on more details on the ACL on SF300:
Configure lists of access based on IPv4 on the 200/300 series managed switches
Thank you
Vijay
Please note the answers.
-
Salvation of the forumers
My problem statement
a. how to let a single switchport to transport the vlan voice and data of vlan?
say I had create and configure the vlan (20) voice and data of vlan (10)
first of all, I do like this (join the voice vlan.png)
What should I do
A1. Management port for VLAN, VLAN
(define the interface as General, but then should I check PVID, tag or remove the brand?)
A2. Management VLAN-VLAN to the Port
(is it leaves vlan 10 and vlan 20 to join the switchport?) (Attach it VLAN to Port.png)
b. is this done switch "ip Routing" for inter routing VLAN?
say I create him VLAN, assign the IP address of the virtual interface for it. Have to do to activate routing inter - VLAN?
I have check the static route only switch IPv4, is that it need a manual to create the static route to reach subnet each VLAN?
can c. that be NTP server?
Thank you
Noel
Hello!
a. create a vlan 10 (data) and vlan 20 (voice). Set the switchport where you have an IP phone that is attached to the Trunk mode (management of Vlan-> settings of the Interface). Administrative PVID of the port should be 10. Go to the management of VLAN-> a Port VLAN membership, select the switchport and click Join VLANS. In the right column, you should have '10UP' (VLAN 10 Untagged, PVID: 10). In the left column select 20, labelling must be tagged, click the right arrow button to add 20 VLAN Tag to the port and click on apply.
These settings will make switchport transfer VLAN10 traffic (data) as non-identified and VLAN20 traffic as added to the phone the voice. In each case, your phone, if it has a PC in the Appendix must be configured for voice traffic with the tag VLAN20 tag and move unidentified to the PC data traffic. Voice of preserve settings VLAN as shown on the screenshot - he let the switch to assign the optimal settings of QoS for traffic vlan voice.
b. If you have the latest firmware installed routing Inter VLAN is enabled by default. Simply create interfaces SVI (assign an IP address to the VIRTUAL local area network interface) and if you have at least a host connected to the switchport member of the VLAN, the road to this subnet will automatically appear in the switch routing table. If you have multiple VLANs with the affected IP addresses and hosts active on these VLAN - all these networks appears in the table of routing as being directly connected and hosts all the VLANS will be able to communicate with each other. You must restrict the Inter-VLAN communication - use IP ACL.
c. No, the switch can be SNTP client only.
-
Hello
I'm get inter vlan routing to work on a 300-24 ports switch DF. I have a network of business existing on 192.168.111.0 and want to create a vlan on 192.168.1.1 which can talk to 192.168.111.0. I activated the layer 3 routing on the switch through the console and also provided ip routing commands. I have the following VIRTUAL networks:
Vlan1 - default 192.168.111.0
VLAN2 - 192.168.1.0
I turned on DNS and provided my two servers DNS 192.168.111.82 & 192.168.111.212.
I updated the VLAN1 interface 192.168.111.217 and VLAN2 interface 192.168.1.1.
The FE1 - FE15 ports are access ports and assigned to VLAN1 (unidentified)
FE16 - FE24 ports are access ports and assigned to VLAN2 (unidentified)
I put a default route for the switch to 0.0.0.0 0.0.0.0 192.168.111.254 (router Draytek 2600). I have connected a computer (A) at the port of VLAN1 FE3 and a computer (B) to VLAN2 FE16 port. I put its IP address and computer default gateway has to 192.168.111.217 to 192.168.111.94. I updated computer B default gateway 192.168.1.1 and 192.168.1.2 IP.
Computer A has access to the Mdaemon Server files via the network grows but no internet (cannot ping google) and can ping computer B and RDP on computer B.
Computer B can ping computer A and RDP on A computer but do not have access to the company network i.e. MDaemon, file server etc. It can also access the internet.
The console I can ping www.google.co.uk and all the ip addresses in the network of the company i.e. 192.168.111.82 (DNS server). I do not understand what I am doing wrong and have been banging my head for staretd a few days a new job and desperately need to work so any help would be greatly appreciated
If I have computer scanner a wireshark wirh internet starts working wheird!
Show the configuration below:
switch7c0a71 #show run
database of VLAN
VLAN 2
output
Add a voice vlan Yes-table 0001e3 Siemens_AG_phone___
Add a voice vlan Yes-table 00036 b Cisco_phone___
Add a voice vlan Yes-table 00096e Avaya___
Add a voice vlan Yes-table 000fe2 H3C_Aolynk___
Add a voice vlan Yes-table 0060 b 9 Philips_and_NEC_AG_phone
Add a voice vlan Yes-table 00d01e Pingtel_phone___
VLAN voice Yes-table add Polycom/Veritel_phone___ 00e075
Add a voice vlan Yes-table 00e0bb 3Com_phone___
interface vlan 2
IP 192.168.1.1 255.255.255.0
output
interface vlan 1
IP 192.168.111.217 255.255.255.0
output
IP route 0.0.0.0 0.0.0.0 192.168.111.254
interface vlan 1
no ip address dhcp
output
Hello interface range vlan 1
hostname switch7c0a71
No complexity of passwords allow
No server snmp Server
interface fastethernet1
switchport mode access
output
interface fastethernet2
switchport mode access
output
interface fastethernet3
switchport mode access
output
interface fastethernet4
switchport mode access
output
interface fastethernet5
switchport mode access
output
fastethernet6 interface
switchport mode access
output
interface fastethernet7
switchport mode access
output
interface fastethernet8
switchport mode access
output
interface fastethernet9
switchport mode access
output
interface fastethernet10
switchport mode access
output
interface fastethernet11
switchport mode access
output
interface fastethernet12
switchport mode access
output
interface fastethernet13
switchport mode access
output
interface fastethernet14
switchport mode access
output
interface fastethernet15
switchport mode access
output
interface fastethernet16
switchport mode general
VLAN allowed switchport General add 2 unidentified
output
interface fastethernet17
switchport mode general
VLAN allowed switchport General add 2 unidentified
output
interface fastethernet18
switchport mode general
VLAN allowed switchport General add 2 unidentified
output
interface fastethernet19
switchport mode general
VLAN allowed switchport General add 2 unidentified
output
interface fastethernet20
switchport mode general
VLAN allowed switchport General add 2 unidentified
output
interface fastethernet21
switchport mode general
VLAN allowed switchport General add 2 unidentified
output
interface fastethernet22
switchport mode general
VLAN allowed switchport General add 2 unidentified
output
interface fastethernet23
switchport mode general
VLAN allowed switchport General add 2 unidentified
output
interface fastethernet24
switchport mode general
VLAN allowed switchport General add 2 unidentified
output
interface vlan 2
name of development
output
Hi Richard,
43 - permit Protocol: any / all
42 - Protocol deny EVERYTHING 192.168.2.0 0.0.0.255-> to 192.168.111.0 0.0.0.255
41 - Protocol to deny ALL 192.168.111.0 0.0.0.255-> to 192.168.2.0 0.0.0.255
40 allow the RDP Protocol TO ALL
etc.
To block everything, including MSSQL, with the exception of the RDP and other ports that you defined above. The other defined are simply not the RDP Protocol and service work?
Richard, do note useful messages and identify the right answers.
Best,
David
-
RV110W inter-VLAN-routing is not possible
In Cisco RV110W, I set up 2 VLANS, a 192.168.1.xxx (Green Net) and the second with only a fixed address 192.168.2.100 192.168.2.xxx (Server), which is configured in the DMZ area. I enabled in Cisco "inter-VLAN-Routing", described "routing between separate VLANs on Cisco RV110W" I can Ping the server in a direktion, the other I got an error. It is just expected and ok! All other abilities expected work well!
Now, I want to see the Green network server. (firewall on the server is off)
I configured the network/router with exactly the values of the index and has been an error: "destination LAN IP may not be the same as the router's IP subnet.
Sorry, I don't understand this. Can anyone help?
Thank you in anticipation
Anton
If I understand correctly, you have a second vlan, 192.168.2.x. The RV110W is a member of this subnet so that's why we do not have a static route for something that the router knows that she welcomes this subnet.
-Tom
Please evaluate the useful messages -
Hello! Everyone.
I have 2 small business sg300 switches connected through a catalyst 2960S, I created 2 VLANS and VLAN 3 on two SG300 connect my servers, but those who do not work properly. I connect a pc to a port in each VLAN on the two switches, then I test ping interfaces connected to this VLAN, but sometimes I only connections of a switch, and nothing when I try the second switch. Or I can reach almost all interfaces connected to the switch and one of them does not. When I disconnect and connect to an interface connected to these switches and try to test again the results change other behaviours.
I Don t need to route via VLAN I want only the link between each VLAN. So I Don t know if it s necessary to assign an IP address for VLANs
I made the other configuration using the web interface:
- I created 2 VLANS and VLAN 3 on each switch SG300 manually and ports assigned to VLANs
- I configured an each SG300 as TRUNK switch port to connect to the catalyst 2960S. And other ports such as access mode.
- In the Cat2960S, I configured the ports connected to each SG300 as TRUNK and the traffic of VLAN enabled if these ports.
The thing is, I don't know what is the problem in my setup. I thought on the GVRP Protocol implementation but Cat2960S support only VTP.
Does anyone know the right steps to implement this configuration or what is the process to implement the GVRP protocol using these 3 switches?
I have attached my diagram to know what I m doing.
Best regards.
Hello
In the two SG300 switch:
Configure the port Fe0/19 in the trunk and VLAN enable this port 1U, 2T, 3T (can be configured on GUI)
Cat2960 switch:
Configure the port Fe0/11.0/12 in the trunk and leave all the VLANS. (Vlan 1 must be native.)
concerning
Deborah
Maybe you are looking for
-
Why do I see tiny Chinese characters in the field of my tabs?
Chinese characters appear in the area of my tabs. As I work, and add tabs more, they get in the way of reading the tabs. I see that others have complained about the same thing. If she does not stop soon I will leave using Firefox.
-
Example: HP laptop 15 TS: disable the cursor pointing
Hi all. new here, so I hope I'm in the right place. I'm having no end of trouble with my 6 month old HP 15 TS Notebook PC, running Windows 10, although this happened the 8.1 win also. This thing "hover cursor" is driving me crazy! How the hell can I
-
Toshiba L 39, 4333 restarts after being turned to connected PC
Hello LED LCD L 39, 4333 correctly starts up and displays PC connected via VGA.Turning also TV on and off work initially and PC is displayed correctly. BUT:If the TV is turned off for long time > 30 min - 1 h with connected PC TV refuses to turn new
-
Cannot add a bug in the incident handler in the BlackBerry Tablet OS project
Hello I get an exception when you create a project in Flash Builder 4 (flex2/tools/oem/OEMException$ CircularLibraryDependencyException). I wanted to add it to the Manager of incidents under the BlackBerry Tablet OS Project (closest to you in the dev
-
BlackBerry BB Z10 User loading Support Forums (only) VERY slowly on Z10
I sent an earlier Z10 swimming & all the rice in China will not save. Therefore, I now have another one, I think it's equally impressive than my previous. Download speeds & page rendering (Z10 Optus Australia) are the best I've experienced on any Mob