Running the scenario of ODI number of command line only (for the linux files) - file not found

Similar Questions

• I come from components to build a new computer. Try to use the Windows XP Pro computer old version but after BIOS and XP installation I get the error "file not found \i386\ntkrnlmp.exe. The error code is 7. "What should I do?

  New components is a new computer.
  Inserted the XP Pro CD in the drive but get the error "file not found \i386\ntkrnlmp.exe. The error code is 7. »
  Rebooted comp 5 times with the same problem after BIOS.

  Hi Milkshake83,

  Thanks for posting. Proceed as follows for this error.

  Method 1: Restore the default settings of the BIOS WARNING: this procedure may involve changing the semiconductor (CMOS) settings of the computer's complementary metal oxide and by changing the BIOS of the computer. Incorrect changes to the BIOS of your computer can result in serious problems. Change the CMOS settings of the computer at your own risk.

  To resolve this issue, restore the BIOS of the computer to its default settings. For more information about the correct settings of the BIOS of the computer and how to check and change these settings, see the computer documentation or contact the manufacturer of the computer.

  In addition, to confirm that the computer's BIOS is current, contact the computer manufacturer to inquire about the last update of the BIOS available for the computer.

  Back to top

  Method 2: Remove the faulty RAM to resolve this issue, remove the memory modules installed in the computer.

  NOTE: you must leave enough RAM for the computer to start and run Windows.

  For more information on the amount of RAM that is required to run Windows, click on the number below to view the article in the Microsoft Knowledge Base:

  304297 configuration (http://support.microsoft.com/kb/304297/) System requirements for Microsoft Windows 2000 operating systems

  If the error message described in the "Symptoms" section of this article appears again after removing the memory module, remove a different memory module. This procedure may ask you to restart your computer several times to identify the specific memory module that is not working properly.

  For more information about how to add and remove RAM to the computer, contact the manufacturer of your computer or see the documentation that came with your computer.

  http://support.Microsoft.com/kb/318729

  I hope this helps!
  Shawn - Support Engineer - MCP, MCDST
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think

• Hello! I get the message "File not found" when I try to access my photos

  Hello! I get the message "File not found" when I try to access my photos in lightroom, and I can't find my photos! I had cleaned up my Mac and deleted by mistake in a different location and now only a gray peak appears in LR, along cable message, file not found. I had saved the raw disk backup files, but it won't let me import into lightroom. (Alright will appear in the import box, but it won't let me even click on it to add. Help!

  In the grid, right-click on an image of 'missing', select 'go to the folder in the library.

  If the folder view does not resemble what you show Finder, right-click on a folder and select 'Show the parent' '; repeat if necessary.

  This will show you where LR thinks that the file was originally.

  You can try to put the images where they were, or place them go elsewhere and 'move' the file in LR.

• Tools command line only for tiger?

  I have an iMac G3 carbon on OS X 10.4.11, with a small hard drive. Is there a command line only version of Xcode 2.5 tools?

  Hello redactedredacted,

  How tiny talk we? XCode 2.5 is less than 1 GB. You can download it here: https://developer.apple.com/downloads/

  Uncheck all the options except for the developer tools and scroll down. I don't know what options are available for the installation of.

• Try to install the downloaded drivers when comes up with the error "file not found".

  Downloaded the drivers Vista for the HP Photosmart premium C410b and installation of hen comes up with the following error message: file not found

  C:/program files/hp C1164EDO-EF08-4B0B-8085-3BDSEAAEFD8D} \gup\at. Any ideas?

  Hi daddums1958,

  Try using the brush included in the CD or download.

  Of the Original installation CD:

  1. Insert the CD in the drive and then cancel Setup

  2. open my computer and click right then on the CD from the drive and select open

  3 open the Util folder

  4 open the CCC folder

  5. run the L4uninstall.exe

  6. once the uninstall is complete, restart the computer

  7 run the Accessories\ System Tools Disk Cleanup

  8. download and install the latest version of Adobe flash player

  http://www.Adobe.com/support/flashplayer/downloads.html

  9 download drivers and full software features

  http://h10025.www1.HP.com/ewfrf/WC/softwareDownloadIndex?softwareitem=MP-84595-1&CC=US&DLC=en&LC=en&os=2093&Product=4186830&sw_lang=

  10. run the download to reinstall the printer

  If the software has been downloaded and extracted to your system:

  1. type % temp % in the field of race

  2. Locate and open the folder starting with 7z (example: 7zS2356)

  3 open the Util folder

  4 open the CCC folder

  5. run the L4uninstall.exe

  6. once the uninstall is complete, restart the computer

  7 run the Accessories\ System Tools Disk Cleanup

  8. download and install the latest version of Adobe flash player

  http://www.Adobe.com/support/flashplayer/downloads.html

  9 download drivers and full software features

  http://h10025.www1.HP.com/ewfrf/WC/softwareDownloadIndex?softwareitem=MP-84595-1&CC=US&DLC=en&LC=en&os=2093&Product=4186830&sw_lang=

  10. run the download to reinstall the printer

• IMAQdx attributes listed in the xml file not found in labview

  Hello

  Some attributes of my camera our watch camera (DALSA CamExpert) software but are not displayed in MAX.

  When I opened the xml file, I don't see a difference between the attributes shown and hidden.

  Why LabView displays all possible attributes?

  The sml file has specific requirements?

  Any ideas?

  Hello Eric,

  I solved the problem yesterday!

  I use a DALSA camera. Dalsa software downloads the XML file and saves it in a directory 'dalsa"on my local disk.

  National instruments software (MAX) downloaded XML file and saves it in another directory. The 2 files were not equal. I replaced the XML file OR the XML of Dalsa file and now I'm able to get all attributes.

  But thanks for your response!

  Kind regards

  Kim

• When you use the copy and collect the files to the new location, I get the error file not found...

  I have 24 hours to media manage and send a feature-length documentary online instead. Everything is ready to go and so I'm going in the media project manager manage all this and I get the following error message:

  

  This is meaningless - why he's looking for the file that it is the copy in the destination folder? The file in question is not in offline mode, it is bound to correctly in the project file and reads without problems. I also tried manually copying the file in the destination folder to see if it changes anything, but no luck.

  I would like ideas, that anyone could have!

  Thank you!

  -Michael

  It seems that because the name of the file was a '-' in there. I changed the name of the file and then reconnected and it has been working fine since.

• Beats audio hp dv-7 6770 ca fails to knit - click the icon for beats = .startup file not found!

  I can't get the software BEATS AUDIO to work in my laptop HP Dv ca - 7 6770

  When you click the icon of BEATS AUDIO you get an error message

  "cannot find file .startup!

  I can't reinstall somewhere or is there a solution?

  Thank you

  Kelly 46

  Hello

  I guess that your model number. is dv7 - 6070ca.

  Download and install the IDT pilot on the link below.

  FTP://ftp.HP.com/pub/SoftPaq/sp52001-52500/sp52399.exe

  Once the installation is complete, restart the laptop.

  Kind regards

  DP - K

• "File required for the Research Assistant is not found." How to restore my ability to use SEARCH?

  Whenever I have use SEARCH after STARTUP I get a message saying that a required file is missing, and that maybe I need to run the installation program. How can I retrieve the missing file and difficulty of RESEARCH?

  Try this link:

  "Error message:"a file that is required to run the search wizard is not found.
    <>http://support.Microsoft.com/kb/319949 >

  HTH,
  JW

• What should I do when after Lightrom 6 worked OK and I was rocking it draws to develop, all of a sudden I have started getting the message "folder or file not found?

  I downloaded photos successfully in Lightroom 6 and were able to develop and even export but suddenly in the process of development or export, Lightroom gives the message "File not found" and "file cannot be found. These pictures are already in Lightroom, how can't he not know where they are? And is it a problem with Lightroom, my computer, or what I did? And what should I do to correct this?

  Photos are never stored in Lightroom. They are stored on your hard drive somewhere, instead you put them, or to the place where you education Lightroom to put them.

  Lightroom is a database. When you import a pohtos, a record is created in the database for each photo, which contains the file name and the location of each photo. When the photo is no longer in the location Lightroom is looking (because somehow the file or folder has been moved, renamed or deleted outside of Lightroom), Lightroom indicates that it does not find the photo (or the photo is missing).

  Therefore, find the photo using your operating system. Once you have found the photo, you must tell Lightroom where the photo is, and what's his name. The exact tools used in this step are described here indetail: Adobe Lightroom - find folders and files moved or missing

• "File not found" error message when you save the document

  Hello

  Oddly enough, whenever I click on 'save' in CS6, it opens a window "save under", (which shouldn't happen), then I click on save witht the existing file name (he said then the doc exist already), I click on OK, (and then on OK to the next popup window) do get the message "file not found".  I have to click on 'ok' and the document is not saved.  I tried to register differently in previous versions, and it still does not work.  I recorded a video of this behavior. You can see here - http://screencast.com/t/W1GYK0zsrk

  Why would he try to find a file?  Looks like an error message when you try to open a doc, does not save a doc.

  Help, please!  I can't stop my station until I get the document to save.

  Yes, Mohit1233 - happened with each file yesterday. Finally, I closed the doc (make me lose my job requires), then restarted my computer and now, that problem has disappeared. I work on a PC (HP);

  Barblove - I tried to do that yesterday (copy and paste into a new doc) and still nothing. I also tried to copy the work in a CS3 doc (but got an error message).

• I, stupid, changed the program by default to a BAT file to the cmd prompt, well, now I can't run the batch files now, please help!

  I, stupid, changed the program by default to a BAT file to the cmd prompt, well, now I can't run the batch files now, please help!

  Hi William,.

  Welcome to the Microsoft community.

  Batch file is a type of script file, a text file, containing a series of commands to be executed by the command prompt. When you run a batch file, it opens the command prompt to run the scripts.

  It would be great if you can answer the following questions:

  1. what happens when you try to run a batch file?

  2 are. what batch file you referring?

  3. the problem occurs for a particular batch file?

  First of all, I suggest you to check the commands written in a batch file. To do the same thing, just right-click on the batch file, and then click change. It will open Notepad with the list of orders scripted for this particular batch file.

  If you have additional questions on the computer, please ask your question about Windows and we will be happy to help you.

• Run the local file after AnyConnect establishes a connection

  We have recently installed a pair of ASA 5525 and ran into a feature that was present on our old Juniper VPN solution that I can't read on the ASAs with AnyConnect news.  With the old solution when the VPN client on the computer of a user connected to the network, we would launch a program on the machine which would then map user share directories and printers - is there a similar solution with the installation of ASA\AnyConnect?  There is a batch file that is present in the same place on each of the assets of the company might be called to run this program, I just can't find a way to run the batch file, if possible.

  A solution to the issue is to have AnyConnect start before the connection of the user, then the program runs when the user opens a Windows session, but I would avoid this scenario if possible - I don't want AnyConnect launch before user logon.

  For any idea or suggestion would be greatly appreciated.

  Thank you.

  Paul

  Yes, this feature exists in anyconnect.

  http://www.Cisco.com/c/en/us/TD/docs/security/vpn_client/AnyConnect/ANYC...

• How do I run the .srt files in wmp 12

  original title: How do I run the .srt files this subtitle files in wmp 12 s? I downloaded directvobsub... but it isn't working...

  I bought a sony vaio e series laptop computer... I downloaded movies to watch and I'm interested to watch in vlc or other players, so I need to know how to watch movies with subtitles... Please help me

  my laptop i5 processor and it is x 64 bit...

  Hello, Sathyasheelan,

  HOW to: Watch movies and TV shows with subtitles

  http://hellboundbloggers.com/2010/06/03/watch-movies-and-TV-series-with-subtitles/

• shortcut for deskjet 8600 pro has disappeared. Re-run the installation program does not help. How can I get that back?

  When I bought and installed my Pro Deskjet 8600 in last July, a wonderful control program has been installed. However, the shortcut on the desktop for this program has disappeared, and I can't. Re-run the installation program does not help. How can I get that back. All I have now is an older version of the HP Solution Center, which does not have the features that I got into the habit of.

  Hello

  Uninstall the software by following programs > HP > HP Officejet Pro 8600 > Uninstall.

  Then download and install the latest version of the software below, it is a more recent software and should solve the problem you are experiencing:

  http://h10025.www1.HP.com/ewfrf/wc/softwareDownloadIndex?softwareitem=bi-108858-3&cc=us&DLC=en&LC=en&OS=4131&product=4323659&sw_lang=

  Shlomi