RV042 and exchange 2010
I bought a RV042 to take advantage of the second internet connection, that we put in place. Port forwarding for the exchange server is currently managed by our main DSL modem/router. After spending some time by configuring the new RV042, I tried to implement yesterday. I changed the setting of the DSL modem/router to bridge and changed the IP address so that it does not enter into conflict with the new router. I unplugged and plugged the cables and I went back to my workstation. I opened a browser and the internet was not working. I pulled out my phone and sent an email of phone to my computer and it worked. Then I tried to send an email from the workstation to the phone. He came back not available immediately, and then I lost the connection to exchange server. He began asked for the password to connect and acted as if I was outside the tent to connect through all the pseudonyms known to our mail server. I even restarted the server of mail without success. I ended up having to remove the RV042 and reset the modem/router DSL to the old settings back to work. Anyone can shed light on what I might have missed in RV042 settings?
Some people are using the protocol binding to bind SSL (port 443) to one of the WAN of RV042 port can work around the problem of authentication with Exchange failure.
Tags: Cisco Support
Similar Questions
-
New to VMware and Exchange 2010
Hello
I'm new to VMware and have some questions about the installer. We just bought a HP DL380 G7 server and Exchange 2010. I want to virtualize this server with a BES. I'm trying to understand the best way to proceed. We also have a Dell EqualLogic iSCSI SAN (PS4000). Wouldn't it be better for me to boot from SAN and have ESxi installed on the SAN? Or would it be preferable for ESxi installed on the server and have my VM hosted/installed on the SAN? Thanks for the help.
Hello owblueiii,
I almose same infrastructure such as this, when I started the virtualization process was confused in this place, finally, we kept the boot on local, VMs oniSCSI SAN.
advantages: 1. because if you have any questions you can the Como.
2 and also a little difficult to troubleshoot if you have the on iscsi san boot partition.
3. you can register your vms on san iscsi timing if you want the new ESX installation.
Hope it's useful to your question.
-
Hi all
We want to improve our ESXis where are hosted Exchange 2010 VMs. We are planning to upgrade to VMware ESXi 6.0 U1a.
Do you know if this version of vSphere is supported by Microsoft? Servers OS of Exchange is Windows Server 2012 Standard.
Thank you
you are welocme
Yes, you are right... it is not supported YET... but take in mind that 6.0 U1 was released last month... so you have to wait a few days/weeks until they test the release.
but it is quite clear that they will also add u1 to list supported... then you can go ahead with the update... don't you worry that
-
Integration of TMSXE with Service Pack 3 for Microsoft Exchange 2010
Hello, we have a TMS 14.3.2, TMSXE 3.1.3 version and Exchange 2010 SP3 with the latest rollup update RU4.
Do we still need to apply the limitation on the Exchange for Exchange 2010SP3 RU4 server policy configuration?. Installation TMSXE document shows that it applies to Exchange 2010 SP1.
Are there specific configuration for Exchange 2010 SP3 RU4 settings?
Yes, the throttling policy applies - the reference SP1 seems to me when the limitation has been enabled on Exchange.
You can use the scheduled throttling policy. Next version of the solution offers impersonation as an alternative, which does not require the throttling policy.
-
Nice day
3 months ago I installed Exchange Server 2010, now I need to recover a mailbox from a backup. The backup was performed while he was still Exchange 2003. I want to know is you can restore an old Exchange 2003 database in the Exchange 2010 recovery store, and if so what is the way forward. PS I use symantec backup exec 2010 R3 as backup software.
If it is not possible, is there any other way to retrieve mailbox information
Any help will be much appreciated.
Hello Wh@pd@p,
I suggest posting your question on our forums TechNet for Microsoft Exchange Server, located here again: -
Need help with Exchange 2010 Diag and implementation
I NEED HELP FOR EXCHANGE 2010 DAG AND THE IMPLEMENTATION THAT CAN HELP-IM I IN THE RIGHT SUPPORT GROUP?
Hello HectorLopez_790,
Microsoft Communities is for consumer issues with Windows 8, Windows 7, Windows Vista and Windows XP. Your question with Exchange would be better supported in the TechNet forums.
Click here for a link to transfer your question in the forums of Exchange.Thank you
Marilyn
-
How to remove messages in Exchange 2010 by dates. in a group and exclude the Contacts, record retention and calendar.
I'm deleting emails from users in a group called MX_Purge file. I need to delete the emails date xx/xx/xxxx to xx/xx/xxxx.
I also need to exclude the excluded the following records 'calendars' folders 'Contacts' and 'Retention '.
The server people hang around more in the TechNet forums, if you ask, you will get a much better response:
http://social.technet.Microsoft.com/forums/en-us/Exchange2010/threads
-
Active Sync iPad ssl Client certificate
How do I configure the iPad2 to synchronize the iPad-Mailclient with Exchange 2010 via Active Sync using the certificate SSL client and name of user and password?
Hi Ewoki,
Your question is more complex than what is generally answered in the Microsoft Answers forums. It is better suited for the TechNet Exchange forum. Please post your question in the Forums TechNet in Exchange Server.
-
Exchange 2010 and high availability (redundancy)
Hello
If virtualize us Exchange 2010 on VMware and Vmotion used for high availability (redundancy). (that is, if we do not have to use Exchange clusters.) Claims we're still two x licenses Exchange 2010?
Thank you
Yes, you will need two exchange server license, if you have less than 5 databases in exchange, you can opt for the standard edition of Exchange. However the operating system you will be required Enterprise edition, as it is necessary for the cluster configuration.
-
vSphere and Microsoft Exchange 2010
Hello anyone know of a guide of best practices for the configuration of Exchange 2010 on vSphere. I think mainly to Cluster Dag requriements regarding HA, DRS and FT
If you have found this device or any other answer useful please consider useful or correct buttons using attribute points
Tom Howarth VCP / vExpert
VMware communities user moderator
Blog: www.planetvm.net
Author of the contribution on "[VMware vSphere and Virtual Infrastructure Security: securing ESX and virtual environment | ]. [ http://www.amazon.co.uk/VMware-VSphere-Virtual-Infrastructure-Security/dp/0137158009/ref=sr_1_1?ie=UTF8 & s = books & qid = 1256146240 & sr = 1-1] & rdquo; .
Author of the contribution on "[VCP VMware Certified Professional on VSphere 4 Study Guide: Exam VCP-410 | ]. [ http://www.amazon.co.uk/VMware-Certified-Professional-VSphere-Study/dp/0470569611] ».
Tom if you can wait a week or two there were also a few sessions at VMworld on this specific topic. I would like to keep an eye on for them when they go out in public for more information as well.
-Kyle
«"RParker wrote: I guess I was mistaken, everything CAN be virtualized"»
-
Cannot receive emails from Exchange 2010
I have Small Business Server 2011 Microsoft and Microsoft Exchange 2010. I'm unable to receive emails.
When I run the Mail Exchange acceptance test, results are:
Presentation has no mail: error message: server does not support secure connections
Should I renew a certificate? If so, how do I? I take more than one other company support and have no previous information.
Thank you!
Hello
Your question is beyond the scope of this community.
I suggest that repost you your Question in Exchange for TechNet Forums.
https://social.technet.Microsoft.com/forums/Exchange/en-us/home?category=ExchangeServer
Or here:
https://social.technet.Microsoft.com/forums/Exchange/en-us/home?Forum=exchangesvrgeneral
SBS forums.
https://social.technet.Microsoft.com/forums/en-us/home?Forum=smallbusinessserver
"Windows Small Business Server 2011 Essentials online help"
https://msdn.Microsoft.com/en-us/library/home-client.aspx
See you soon.
-
Problem of Exchange 2010 TLS 1.0
Hi all
I have a windows 2008r2 with exchange 2010 with RU11
TLS 1.1 and 1.2 active
I installed the Update Rollup 4,6,7,8-v2, 10, 11
If I disable tls 1.0 mail will not be sent. This patch should be RU9.
I thought that the UK is cumulative? I made a mistake and
I have to install ru9? is it possible after ru11?
regarding
Patrick
Hello
Post your question in the TechNet Server Forums, as your question kindly is beyond the scope of these Forums.
http://social.technet.Microsoft.com/forums/WindowsServer/en-us/home?category=WindowsServer
Or in the Exchange Server TechNet Forums.
https://social.technet.Microsoft.com/forums/Exchange/en-us/home?category=ExchangeServer
See you soon.
-
Hello
I have exchange 2010 server and 2 links internet service, is there a way to let the server switch between links when the first link is down?
Hello
Your Question is beyond the scope of this community.
Kindly forward your Question in the TechNet Forums of Exchange Server.
https://social.technet.Microsoft.com/forums/Exchange/en-us/home?category=ExchangeServer
See you soon.
-
Hello
We have Microsoft Exchange 2010 in our organization with 50 user licenses, which works very well; recently we have 100 user Exchange 2013 licenses and according to the dealer, we can even add to an existing installation of 2010 that will be club licenses 50 + 100 = 150. Here now to get the answer for sub queries before you continue.
How can we add 100 user licenses at the multinational level to Exchange 2013 in our existing work 2010 installation?
It will affect the existing environment?
Thank you & best regards
Ziani
This issue is beyond the scope of this site (for consumers) and to be sure, you get the best (and fastest) reply, we have to ask either on Technet (for IT Pro) or MSDN (for developers)* -
Exchange 2010 SP3 Rollup Update 11 not no projection in WSUS / / SCCM
Hey all,.
I just wanted to see if anyone is noticing that Exchange 2010 SP3 Rollup 11 does not appear in their WSUS or SCCM. I ran Resync to see if they go up, as well as leave a traction of Exchange Server for updates from the internet. Or see the KB3078674
This is normal behavior for a published update recently?
This issue is beyond the scope of this site (for consumers) and to be sure, you get the best (and fastest) reply, we have to ask either on Technet (for IT Pro) or MSDN (for developers)*
Maybe you are looking for
-
Satellite Pro M10 will accept another motherboard model?
Hi chaps.It was established that my motherboard M10 is a bit dead. It's cheaper to replace the motherboard, but there is not a lot of second hand M10 motherboards are so thought someone here knows if held on another motherboard and a similar model wo
-
Can I download an iso of Windows site with a new unused OEM key
-
iMac early 2008 fails to boot completely
Hi all - I have an early 2008 iMac 3.06 GHz 24 "model that starts more completely. The system gets to the Apple screen and the progress bar comes in at halfway and there it is. I had replaced the original HARD with a SDD drive and had not had any pro
-
Windows Vista - 0 x 8008005 error, won't allow software updates
I experience problems when you try to download updates for windows and other programs on the computer. This includes SP2. I use Windows Vista, 32-bit, currently on SP1. When tempting to windows updates the following error is 0 x 80080005 recurring. I
-
I went out just to get the WMP110 Rangeplus PCI as well as a new computer. I started the computer and installed the drivers for this card and then turn off the computer put in card and start back, etc.. Then, he gives me a screen where it says congra